-
#
# Network device configuration
#
config MACB
tristate "Atmel MACB support"
- depends on AVR32 || ARCH_AT91SAM9260 || ARCH_AT91SAM9263 || ARCH_AT91SAM9G20 || ARCH_AT91CAP9
+ depends on AVR32 || ARCH_AT91SAM9260 || ARCH_AT91SAM9263 || ARCH_AT91SAM9G20 || ARCH_AT91SAM9G45 || ARCH_AT91CAP9
select PHYLIB
help
The Atmel MACB ethernet interface is found on many AT32 and AT91
config SH_ETH
tristate "Renesas SuperH Ethernet support"
depends on SUPERH && \
- (CPU_SUBTYPE_SH7710 || CPU_SUBTYPE_SH7712 || CPU_SUBTYPE_SH7763 || \
- CPU_SUBTYPE_SH7619)
+ (CPU_SUBTYPE_SH7710 || CPU_SUBTYPE_SH7712 || \
+ CPU_SUBTYPE_SH7763 || CPU_SUBTYPE_SH7619 || \
+ CPU_SUBTYPE_SH7724)
select CRC32
select MII
select MDIO_BITBANG
select PHYLIB
help
Renesas SuperH Ethernet device driver.
- This driver support SH7710, SH7712, SH7763 and SH7619.
+ This driver support SH7710, SH7712, SH7763, SH7619, and SH7724.
config SUNLANCE
tristate "Sun LANCE support"
To compile this driver as a module, choose M here. The module
will be called netx-eth.
+config TI_DAVINCI_EMAC
+ tristate "TI DaVinci EMAC Support"
+ depends on ARM && ARCH_DAVINCI
+ select PHYLIB
+ help
+ This driver supports TI's DaVinci Ethernet .
+
+ To compile this driver as a module, choose M here: the module
+ will be called davinci_emac_driver. This is recommended.
+
config DM9000
tristate "DM9000 support"
depends on ARM || BLACKFIN || MIPS
Enable the verify after the buffer write useful for debugging purpose.
If unsure, say N.
+config ETHOC
+ tristate "OpenCores 10/100 Mbps Ethernet MAC support"
+ depends on NET_ETHERNET && HAS_IOMEM && HAS_DMA
+ select MII
+ select PHYLIB
+ select CRC32
+ select BITREVERSE
+ help
+ Say Y here if you want to use the OpenCores 10/100 Mbps Ethernet MAC.
+
config SMC911X
tristate "SMSC LAN911[5678] support"
select CRC32
config SMSC911X
tristate "SMSC LAN911x/LAN921x families embedded ethernet support"
- depends on ARM || SUPERH
+ depends on ARM || SUPERH || BLACKFIN || MIPS
select CRC32
select MII
select PHYLIB
To compile this driver as a module, choose M here. The module
will be called ni65.
+config DNET
+ tristate "Dave ethernet support (DNET)"
+ depends on NET_ETHERNET && HAS_IOMEM
+ select PHYLIB
+ help
+ The Dave ethernet interface (DNET) is found on Qong Board FPGA.
+ Say Y to include support for the DNET chip.
+
+ To compile this driver as a module, choose M here: the module
+ will be called dnet.
+
source "drivers/net/tulip/Kconfig"
config AT1700
Please email feedback to <torben.mathiasen@compaq.com>.
+config KS8842
+ tristate "Micrel KSZ8842"
+ depends on HAS_IOMEM
+ help
+ This platform driver is for Micrel KSZ8842 / KS8842
+ 2-port ethernet switch chip (managed, VLAN, QoS).
+
+config KS8851
+ tristate "Micrel KS8851 SPI"
+ depends on SPI
+ select MII
+ select CRC32
+ help
+ SPI driver for Micrel KS8851 SPI attached network chip.
+
+config KS8851_MLL
+ tristate "Micrel KS8851 MLL"
+ depends on HAS_IOMEM
+ select MII
+ help
+ This platform driver is for Micrel KS8851 Address/data bus
+ multiplexed network chip.
+
config VIA_RHINE
tristate "VIA Rhine support"
depends on NET_PCI && PCI
config CPMAC
tristate "TI AR7 CPMAC Ethernet support (EXPERIMENTAL)"
- depends on NET_ETHERNET && EXPERIMENTAL && AR7 && BROKEN
+ depends on NET_ETHERNET && EXPERIMENTAL && AR7
select PHYLIB
help
TI AR7 CPMAC Ethernet support
the Motorola 68360 processor.
config FEC
- bool "FEC ethernet controller (of ColdFire CPUs)"
- depends on M523x || M527x || M5272 || M528x || M520x || M532x || MACH_MX27
+ bool "FEC ethernet controller (of ColdFire and some i.MX CPUs)"
+ depends on M523x || M527x || M5272 || M528x || M520x || M532x || MACH_MX27 || ARCH_MX35 || ARCH_MX25
help
Say Y here if you want to use the built-in 10/100 Fast ethernet
controller on some Motorola ColdFire and Freescale i.MX processors.
---help---
This option enables support for the MPC5200's on-chip
Fast Ethernet Controller
- If compiled as module, it will be called 'fec_mpc52xx.ko'.
+ If compiled as module, it will be called fec_mpc52xx.
config FEC_MPC52xx_MDIO
bool "MPC52xx FEC MDIO bus driver"
(Motorola? industry standard).
If your board uses an external PHY connected to FEC, enable this.
If not sure, enable.
- If compiled as module, it will be called 'fec_mpc52xx_phy.ko'.
+ If compiled as module, it will be called fec_mpc52xx_phy.
config NE_H8300
tristate "NE2000 compatible support for H8/300"
To compile this driver as a module, choose M here. The module
will be called atl2.
+config XILINX_EMACLITE
+ tristate "Xilinx 10/100 Ethernet Lite support"
+ depends on PPC32 || MICROBLAZE
+ help
+ This driver supports the 10/100 Ethernet Lite from Xilinx.
+
+config BCM63XX_ENET
+ tristate "Broadcom 63xx internal mac support"
+ depends on BCM63XX
+ select MII
+ select PHYLIB
+ help
+ This driver supports the ethernet MACs in the Broadcom 63xx
+ MIPS chipset family (BCM63XX).
+
source "drivers/net/fs_enet/Kconfig"
endif # NET_ETHERNET
To compile this driver as a module, choose M here. The module
will be called igb.
-config IGB_LRO
- bool "Use software LRO"
- depends on IGB && INET
- ---help---
- Say Y here if you want to use large receive offload.
-
- If in doubt, say N.
-
config IGB_DCA
bool "Direct Cache Access (DCA) Support"
default y
driver. DCA is a method for warming the CPU cache before data
is used, with the intent of lessening the impact of cache misses.
+config IGBVF
+ tristate "Intel(R) 82576 Virtual Function Ethernet support"
+ depends on PCI
+ ---help---
+ This driver supports Intel(R) 82576 virtual functions. For more
+ information on how to identify your adapter, go to the Adapter &
+ Driver ID Guide at:
+
+ <http://support.intel.com/support/network/adapter/pro100/21397.htm>
+
+ For general information and support, go to the Intel support
+ website at:
+
+ <http://support.intel.com>
+
+ More specific information on configuring the driver is in
+ <file:Documentation/networking/e1000.txt>.
+
+ To compile this driver as a module, choose M here. The module
+ will be called igbvf.
+
source "drivers/net/ixp2000/Kconfig"
config MYRI_SBUS
depends on SKGE && DEBUG_FS
help
This option adds the ability to dump driver state for debugging.
- The file debugfs/skge/ethX displays the state of the internal
+ The file /sys/kernel/debug/skge/ethX displays the state of the internal
transmit and receive rings.
If unsure, say N.
depends on SKY2 && DEBUG_FS
help
This option adds the ability to dump driver state for debugging.
- The file debugfs/sky2/ethX displays the state of the internal
+ The file /sys/kernel/debug/sky2/ethX displays the state of the internal
transmit and receive rings.
If unsure, say N.
tristate "Broadcom NetXtremeII support"
depends on PCI
select CRC32
- select ZLIB_INFLATE
+ select FW_LOADER
help
This driver supports Broadcom NetXtremeII gigabit Ethernet cards.
To compile this driver as a module, choose M here: the module
will be called bnx2. This is recommended.
+config CNIC
+ tristate "Broadcom CNIC support"
+ depends on PCI
+ select BNX2
+ select UIO
+ help
+ This driver supports offload features of Broadcom NetXtremeII
+ gigabit Ethernet cards.
+
+ To compile this driver as a module, choose M here: the module
+ will be called cnic. This is recommended.
+
config SPIDER_NET
tristate "Spider Gigabit Ethernet driver"
depends on PCI && (PPC_IBM_CELL_BLADE || PPC_CELLEB)
config GELIC_WIRELESS
bool "PS3 Wireless support"
+ depends on WLAN
depends on GELIC_NET
select WIRELESS_EXT
help
config GELIC_WIRELESS_OLD_PSK_INTERFACE
bool "PS3 Wireless private PSK interface (OBSOLETE)"
depends on GELIC_WIRELESS
+ select WEXT_PRIV
help
This option retains the obsolete private interface to pass
the PSK from user space programs to the driver. The PSK
This driver supports the Gigabit Ethernet mode of the QUICC Engine,
which is available on some Freescale SOCs.
-config UGETH_MAGIC_PACKET
- bool "Magic Packet detection support"
- depends on UCC_GETH
-
config UGETH_TX_ON_DEMAND
bool "Transmit on Demand support"
depends on UCC_GETH
config MV643XX_ETH
tristate "Marvell Discovery (643XX) and Orion ethernet support"
- depends on MV64360 || MV64X60 || (PPC_MULTIPLATFORM && PPC32) || PLAT_ORION
+ depends on MV64X60 || PPC32 || PLAT_ORION
+ select INET_LRO
select PHYLIB
help
This driver supports the gigabit ethernet MACs in the
Some boards that use the Discovery chipset are the Momenco
Ocelot C and Jaguar ATX and Pegasos II.
-config MV643XX_ETH_LRO
- tristate "Marvell 643XX ethernet driver LRO support"
- depends on MV643XX_ETH
- select INET_LRO
+config XILINX_LL_TEMAC
+ tristate "Xilinx LL TEMAC (LocalLink Tri-mode Ethernet MAC) driver"
+ select PHYLIB
+ depends on PPC_DCR_NATIVE
help
- Say y here if you want to use Large Receive Offload for the
- mv643xx_eth driver.
-
- If in doubt, say N.
+ This driver supports the Xilinx 10/100/1000 LocalLink TEMAC
+ core used in Xilinx Spartan and Virtex FPGAs
config QLA3XXX
tristate "QLogic QLA3XXX Network Driver Support"
To compile this driver as a module, choose M here. The module
will be called atl1e.
+config ATL1C
+ tristate "Atheros L1C Gigabit Ethernet support (EXPERIMENTAL)"
+ depends on PCI && EXPERIMENTAL
+ select CRC32
+ select MII
+ help
+ This driver supports the Atheros L1C gigabit ethernet adapter.
+
+ To compile this driver as a module, choose M here. The module
+ will be called atl1c.
+
config JME
tristate "JMicron(R) PCI-Express Gigabit Ethernet support"
depends on PCI
To compile this driver as a module, choose M here. The module
will be called jme.
+config S6GMAC
+ tristate "S6105 GMAC ethernet support"
+ depends on XTENSA_VARIANT_S6000
+ select PHYLIB
+ help
+ This driver supports the on chip ethernet device on the
+ S6105 xtensa processor.
+
+ To compile this driver as a module, choose M here. The module
+ will be called s6gmac.
+
+source "drivers/net/stmmac/Kconfig"
+
endif # NETDEV_1000
#
if NETDEV_10000
+config MDIO
+ tristate
+
config CHELSIO_T1
tristate "Chelsio 10Gb Ethernet support"
depends on PCI
select CRC32
+ select MDIO
help
This driver supports Chelsio gigabit and 10-gigabit
Ethernet cards. More information about adapter features and
tristate "Chelsio Communications T3 10Gb Ethernet support"
depends on CHELSIO_T3_DEPENDS
select FW_LOADER
+ select MDIO
help
This driver supports Chelsio T3-based gigabit and 10Gb Ethernet
adapters.
config IXGBE
tristate "Intel(R) 10GbE PCI Express adapters support"
depends on PCI && INET
+ select MDIO
---help---
This driver supports Intel(R) 10GbE PCI Express family of
adapters. For more information on how to identify your adapter, go
More specific information on configuring the driver is in
<file:Documentation/networking/s2io.txt>.
+config VXGE
+ tristate "Neterion X3100 Series 10GbE PCIe Server Adapter"
+ depends on PCI && INET
+ ---help---
+ This driver supports Neterion Inc's X3100 Series 10 GbE PCIe
+ I/O Virtualized Server Adapter.
+ More specific information on configuring the driver is in
+ <file:Documentation/networking/vxge.txt>.
+
+config VXGE_DEBUG_TRACE_ALL
+ bool "Enabling All Debug trace statments in driver"
+ default n
+ depends on VXGE
+ ---help---
+ Say Y here if you want to enabling all the debug trace statements in
+ driver. By default only few debug trace statements are enabled.
+
config MYRI10GE
tristate "Myricom Myri-10G Ethernet support"
depends on PCI && INET
config NIU
tristate "Sun Neptune 10Gbit Ethernet support"
depends on PCI
+ select CRC32
help
This enables support for cards based upon Sun's
Neptune chipset.
config BNX2X
tristate "Broadcom NetXtremeII 10Gb support"
depends on PCI
+ select FW_LOADER
select ZLIB_INFLATE
select LIBCRC32C
+ select MDIO
help
This driver supports Broadcom NetXtremeII 10 gigabit Ethernet cards.
To compile this driver as a module, choose M here: the module
source "drivers/net/sfc/Kconfig"
+source "drivers/net/benet/Kconfig"
+
endif # NETDEV_10000
source "drivers/net/tokenring/Kconfig"
source "drivers/atm/Kconfig"
+source "drivers/ieee802154/Kconfig"
+
source "drivers/s390/net/Kconfig"
config XEN_NETDEV_FRONTEND
This is the virtual network driver for virtio. It can be used with
lguest or QEMU based VMMs (like KVM or Xen). Say Y or M.
+config VMXNET3
+ tristate "VMware VMXNET3 ethernet driver"
+ depends on PCI && INET
+ help
+ This driver supports VMware's vmxnet3 virtual ethernet NIC.
+ To compile this driver as a module, choose M here: the
+ module will be called vmxnet3.
+
endif # NETDEVICES
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff