config BONDING
tristate "Bonding driver support"
depends on INET
+ depends on IPV6 || IPV6=n
---help---
Say 'Y' or 'M' if you wish to be able to 'bond' multiple Ethernet
Channels together. This is called 'Etherchannel' by Cisco,
This is the driver for the onboard card of MIPS Magnum 4000,
Acer PICA, Olivetti M700-10 and a few other identical OEM systems.
+config XTENSA_XT2000_SONIC
+ tristate "Xtensa XT2000 onboard SONIC Ethernet support"
+ depends on XTENSA_PLATFORM_XT2000
+ help
+ This is the driver for the onboard card of the Xtensa XT2000 board.
+
config MIPS_AU1X00_ENET
bool "MIPS AU1000 Ethernet support"
depends on SOC_AU1X00
config BFIN_MAC
tristate "Blackfin on-chip MAC support"
- depends on NET_ETHERNET && (BF526 || BF527 || BF536 || BF537)
+ depends on NET_ETHERNET && (BF516 || BF518 || BF526 || BF527 || BF536 || BF537)
select CRC32
select MII
select PHYLIB
select CRC32
select MII
depends on ARM || REDWOOD_5 || REDWOOD_6 || M32R || SUPERH || \
- SOC_AU1X00 || BLACKFIN || MN10300
+ MIPS || BLACKFIN || MN10300
help
This is a driver for SMC's 91x series of Ethernet chipsets,
including the SMC91C94 and the SMC91C111. Say Y if you want it
tristate "SMSC LAN911[5678] support"
select CRC32
select MII
- depends on ARCH_PXA || SUPERH
+ depends on ARM || SUPERH
help
This is a driver for SMSC's LAN911x series of Ethernet chipsets
including the new LAN9115, LAN9116, LAN9117, and LAN9118.
called smc911x. If you want to compile it as a module, say M
here and read <file:Documentation/kbuild/modules.txt>
+config SMSC911X
+ tristate "SMSC LAN911x/LAN921x families embedded ethernet support"
+ depends on ARM || SUPERH
+ select CRC32
+ select MII
+ select PHYLIB
+ ---help---
+ Say Y here if you want support for SMSC LAN911x and LAN921x families
+ of ethernet controllers.
+
+ To compile this driver as a module, choose M here and read
+ <file:Documentation/networking/net-modules.txt>. The module
+ will be called smsc911x.
+
config NET_VENDOR_RACAL
bool "Racal-Interlan (Micom) NI cards"
depends on ISA
config CS89x0
tristate "CS89x0 support"
- depends on NET_PCI && (ISA || MACH_IXDP2351 || ARCH_IXDP2X01 || ARCH_PNX010X)
+ depends on NET_ETHERNET && (ISA || EISA || MACH_IXDP2351 \
+ || ARCH_IXDP2X01 || ARCH_PNX010X || MACH_MX31ADS)
---help---
Support for CS89x0 chipset based Ethernet cards. If you have a
network (Ethernet) card of this type, say Y and read the
To compile this driver as a module, choose M here. The module
will be called cs89x0.
+config CS89x0_NONISA_IRQ
+ def_bool y
+ depends on CS89x0 != n
+ depends on MACH_IXDP2351 || ARCH_IXDP2X01 || ARCH_PNX010X || MACH_MX31ADS
+
config TC35815
tristate "TOSHIBA TC35815 Ethernet support"
depends on NET_PCI && PCI && MIPS
select PHYLIB
-config EEPRO100
- tristate "EtherExpressPro/100 support (eepro100, original Becker driver)"
- depends on NET_PCI && PCI
- select MII
- help
- If you have an Intel EtherExpress PRO/100 PCI network (Ethernet)
- card, say Y and read the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>.
-
- To compile this driver as a module, choose M here. The module
- will be called eepro100.
-
-
config E100
tristate "Intel(R) PRO/100+ support"
depends on NET_PCI && PCI
More specific information and updates are available from
<http://www.scyld.com/network/epic100.html>.
+config SMSC9420
+ tristate "SMSC LAN9420 PCI ethernet adapter support"
+ depends on NET_PCI && PCI
+ select CRC32
+ select PHYLIB
+ select SMSC_PHY
+ help
+ This is a driver for SMSC's LAN9420 PCI ethernet adapter.
+ Say Y if you want it compiled into the kernel,
+ and read the Ethernet-HOWTO, available from
+ <http://www.linuxdoc.org/docs.html#howto>.
+
+ This driver is also available as a module. The module will be
+ called smsc9420. If you want to compile it as a module, say M
+ here and read <file:Documentation/kbuild/modules.txt>
+
config SUNDANCE
tristate "Sundance Alta support"
depends on NET_PCI && PCI
config FEC_MPC52xx
tristate "MPC52xx FEC driver"
- depends on PPC_MERGE && PPC_MPC52xx && PPC_BESTCOMM_FEC
+ depends on PPC_MPC52xx && PPC_BESTCOMM
select CRC32
select PHYLIB
+ select PPC_BESTCOMM_FEC
---help---
This option enables support for the MPC5200's on-chip
Fast Ethernet Controller
To compile this driver as a module, choose M here. The module
will be called e1000.
-config E1000_DISABLE_PACKET_SPLIT
- bool "Disable Packet Split for PCI express adapters"
- depends on E1000
- help
- Say Y here if you want to use the legacy receive path for PCI express
- hardware.
-
- If in doubt, say N.
-
config E1000E
tristate "Intel(R) PRO/1000 PCI-Express Gigabit Ethernet support"
depends on PCI && (!SPARC32 || BROKEN)
will be called ipg. This is recommended.
config IGB
- tristate "Intel(R) 82575 PCI-Express Gigabit Ethernet support"
+ tristate "Intel(R) 82575/82576 PCI-Express Gigabit Ethernet support"
depends on PCI
---help---
- This driver supports Intel(R) 82575 gigabit ethernet family of
+ This driver supports Intel(R) 82575/82576 gigabit ethernet family of
adapters. For more information on how to identify your adapter, go
to the Adapter & Driver ID Guide at:
If in doubt, say N.
+config IGB_DCA
+ bool "Direct Cache Access (DCA) Support"
+ default y
+ depends on IGB && DCA && !(IGB=y && DCA=m)
+ ---help---
+ Say Y here if you want to use Direct Cache Access (DCA) in the
+ driver. DCA is a method for warming the CPU cache before data
+ is used, with the intent of lessening the impact of cache misses.
+
source "drivers/net/ixp2000/Kconfig"
config MYRI_SBUS
tristate "Realtek 8169 gigabit ethernet support"
depends on PCI
select CRC32
+ select MII
---help---
Say Y here if you have a Realtek 8169 PCI Gigabit Ethernet adapter.
bool "Magic Packet detection support"
depends on UCC_GETH
-config UGETH_FILTERING
- bool "Mac address filtering support"
- depends on UCC_GETH
-
config UGETH_TX_ON_DEMAND
bool "Transmit on Demand support"
depends on UCC_GETH
config MV643XX_ETH
tristate "Marvell Discovery (643XX) and Orion ethernet support"
depends on MV64360 || MV64X60 || (PPC_MULTIPLATFORM && PPC32) || PLAT_ORION
- select MII
+ select PHYLIB
help
This driver supports the gigabit ethernet MACs in the
Marvell Discovery PPC/MIPS chipset family (MV643XX) and
will be called qla3xxx.
config ATL1
- tristate "Attansic L1 Gigabit Ethernet support (EXPERIMENTAL)"
- depends on PCI && EXPERIMENTAL
+ tristate "Atheros/Attansic L1 Gigabit Ethernet support"
+ depends on PCI
select CRC32
select MII
help
- This driver supports the Attansic L1 gigabit ethernet adapter.
+ This driver supports the Atheros/Attansic L1 gigabit ethernet
+ adapter.
To compile this driver as a module, choose M here. The module
will be called atl1.
To compile this driver as a module, choose M here. The module
will be called atl1e.
+config JME
+ tristate "JMicron(R) PCI-Express Gigabit Ethernet support"
+ depends on PCI
+ select CRC32
+ select MII
+ ---help---
+ This driver supports the PCI-Express gigabit ethernet adapters
+ based on JMicron JMC250 chipset.
+
+ To compile this driver as a module, choose M here. The module
+ will be called jme.
+
endif # NETDEV_1000
#
Enables support for Chelsio's gigabit Ethernet PCI cards. If you
are using only 10G cards say 'N' here.
+config CHELSIO_T3_DEPENDS
+ tristate
+ depends on PCI && INET
+ default y
+
config CHELSIO_T3
tristate "Chelsio Communications T3 10Gb Ethernet support"
- depends on PCI && INET
+ depends on CHELSIO_T3_DEPENDS
select FW_LOADER
select INET_LRO
help
To compile the driver as a module, choose M here. The module
will be called ehea.
+config ENIC
+ tristate "Cisco 10G Ethernet NIC support"
+ depends on PCI && INET
+ select INET_LRO
+ help
+ This enables the support for the Cisco 10G Ethernet card.
+
config IXGBE
tristate "Intel(R) 10GbE PCI Express adapters support"
depends on PCI && INET
To compile this driver as a module, choose M here. The module
will be called ixgbe.
+config IXGBE_DCA
+ bool "Direct Cache Access (DCA) Support"
+ default y
+ depends on IXGBE && DCA && !(IXGBE=y && DCA=m)
+ ---help---
+ Say Y here if you want to use Direct Cache Access (DCA) in the
+ driver. DCA is a method for warming the CPU cache before data
+ is used, with the intent of lessening the impact of cache misses.
+
+config IXGBE_DCB
+ bool "Data Center Bridging (DCB) Support"
+ default n
+ depends on IXGBE && DCB
+ ---help---
+ Say Y here if you want to use Data Center Bridging (DCB) in the
+ driver.
+
+ If unsure, say N.
+
config IXGB
tristate "Intel(R) PRO/10GbE support"
depends on PCI
To compile this driver as a module, choose M here. The module
will be called myri10ge.
+config MYRI10GE_DCA
+ bool "Direct Cache Access (DCA) Support"
+ default y
+ depends on MYRI10GE && DCA && !(MYRI10GE=y && DCA=m)
+ ---help---
+ Say Y here if you want to use Direct Cache Access (DCA) in the
+ driver. DCA is a method for warming the CPU cache before data
+ is used, with the intent of lessening the impact of cache misses.
+
config NETXEN_NIC
tristate "NetXen Multi port (1/10) Gigabit Ethernet NIC"
depends on PCI
This driver supports the on-chip 1/10Gbit Ethernet controller on
PA Semi's PWRficient line of chips.
+config MLX4_EN
+ tristate "Mellanox Technologies 10Gbit Ethernet support"
+ depends on PCI && INET
+ select MLX4_CORE
+ select INET_LRO
+ help
+ This driver supports Mellanox Technologies ConnectX Ethernet
+ devices.
+
config MLX4_CORE
tristate
depends on PCI
To compile this driver as a module, choose M here: the module
will be called bnx2x. This is recommended.
+config QLGE
+ tristate "QLogic QLGE 10Gb Ethernet Driver Support"
+ depends on PCI
+ help
+ This driver supports QLogic ISP8XXX 10Gb Ethernet cards.
+
+ To compile this driver as a module, choose M here: the module
+ will be called qlge.
+
source "drivers/net/sfc/Kconfig"
endif # NETDEV_10000
source "drivers/net/wireless/Kconfig"
+source "drivers/net/wimax/Kconfig"
+
source "drivers/net/usb/Kconfig"
source "drivers/net/pcmcia/Kconfig"
default "128"
config FDDI
- bool "FDDI driver support"
+ tristate "FDDI driver support"
depends on (PCI || EISA || TC)
help
Fiber Distributed Data Interface is a high speed local area network
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff