# that for each of the symbols.
if NETDEVICES
-config NETDEVICES_MULTIQUEUE
- bool "Netdevice multiple hardware queue support"
- ---help---
- Say Y here if you want to allow the network stack to use multiple
- hardware TX queues on an ethernet device.
-
- Most people will say N here.
-
config IFB
tristate "Intermediate Functional Block support"
depends on NET_CLS_ACT
config BONDING
tristate "Bonding driver support"
depends on INET
+ depends on IPV6 || IPV6=n
---help---
Say 'Y' or 'M' if you wish to be able to 'bond' multiple Ethernet
Channels together. This is called 'Etherchannel' by Cisco,
config MACB
tristate "Atmel MACB support"
- depends on AVR32 || ARCH_AT91SAM9260 || ARCH_AT91SAM9263 || ARCH_AT91CAP9
+ depends on AVR32 || ARCH_AT91SAM9260 || ARCH_AT91SAM9263 || ARCH_AT91SAM9G20 || ARCH_AT91CAP9
select PHYLIB
help
The Atmel MACB ethernet interface is found on many AT32 and AT91
To compile this driver as a module, choose M here: the module
will be called apne.
-config APOLLO_ELPLUS
- tristate "Apollo 3c505 support"
- depends on APOLLO
- help
- Say Y or M here if your Apollo has a 3Com 3c505 ISA Ethernet card.
- If you don't have one made for Apollos, you can use one from a PC,
- except that your Apollo won't be able to boot from it (because the
- code in the ROM will be for a PC).
-
config MAC8390
bool "Macintosh NS 8390 based ethernet cards"
depends on MAC
config KORINA
tristate "Korina (IDT RC32434) Ethernet support"
- depends on NET_ETHERNET && MIKROTIK_RB500
+ depends on NET_ETHERNET && MIKROTIK_RB532
help
If you have a Mikrotik RouterBoard 500 or IDT RC32434
based system say Y. Otherwise say N.
This is the driver for the onboard card of MIPS Magnum 4000,
Acer PICA, Olivetti M700-10 and a few other identical OEM systems.
+config XTENSA_XT2000_SONIC
+ tristate "Xtensa XT2000 onboard SONIC Ethernet support"
+ depends on XTENSA_PLATFORM_XT2000
+ help
+ This is the driver for the onboard card of the Xtensa XT2000 board.
+
config MIPS_AU1X00_ENET
bool "MIPS AU1000 Ethernet support"
depends on SOC_AU1X00
If unsure, say N.
+config SH_ETH
+ tristate "Renesas SuperH Ethernet support"
+ depends on SUPERH && \
+ (CPU_SUBTYPE_SH7710 || CPU_SUBTYPE_SH7712 || CPU_SUBTYPE_SH7763 || \
+ CPU_SUBTYPE_SH7619)
+ select CRC32
+ select MII
+ select MDIO_BITBANG
+ select PHYLIB
+ help
+ Renesas SuperH Ethernet device driver.
+ This driver support SH7710, SH7712, SH7763 and SH7619.
+
config SUNLANCE
tristate "Sun LANCE support"
depends on SBUS
will be called smc-ultra32.
config BFIN_MAC
- tristate "Blackfin 527/536/537 on-chip mac support"
- depends on NET_ETHERNET && (BF527 || BF537 || BF536)
+ tristate "Blackfin on-chip MAC support"
+ depends on NET_ETHERNET && (BF516 || BF518 || BF526 || BF527 || BF536 || BF537)
select CRC32
select MII
select PHYLIB
select BFIN_MAC_USE_L1 if DMA_UNCACHED_NONE
help
- This is the driver for blackfin on-chip mac device. Say Y if you want it
+ This is the driver for Blackfin on-chip mac device. Say Y if you want it
compiled into the kernel. This driver is also available as a module
( = code which can be inserted in and removed from the running kernel
whenever you want). The module will be called bfin_mac.
select CRC32
select MII
depends on ARM || REDWOOD_5 || REDWOOD_6 || M32R || SUPERH || \
- SOC_AU1X00 || BLACKFIN || MN10300
+ MIPS || BLACKFIN || MN10300
help
This is a driver for SMC's 91x series of Ethernet chipsets,
including the SMC91C94 and the SMC91C111. Say Y if you want it
To compile this driver as a module, choose M here. The module
will be called dm9000.
+config DM9000_DEBUGLEVEL
+ int "DM9000 maximum debug level"
+ depends on DM9000
+ default 4
+ help
+ The maximum level of debugging code compiled into the DM9000
+ driver.
+
+config DM9000_FORCE_SIMPLE_PHY_POLL
+ bool "Force simple NSR based PHY polling"
+ depends on DM9000
+ ---help---
+ This configuration forces the DM9000 to use the NSR's LinkStatus
+ bit to determine if the link is up or down instead of the more
+ costly MII PHY reads. Note, this will not work if the chip is
+ operating with an external PHY.
+
config ENC28J60
tristate "ENC28J60 support"
depends on EXPERIMENTAL && SPI && NET_ETHERNET
Enable the verify after the buffer write useful for debugging purpose.
If unsure, say N.
-config DM9000_DEBUGLEVEL
- int "DM9000 maximum debug level"
- depends on DM9000
- default 4
- help
- The maximum level of debugging code compiled into the DM9000
- driver.
-
config SMC911X
tristate "SMSC LAN911[5678] support"
select CRC32
select MII
- depends on ARCH_PXA || SH_MAGIC_PANEL_R2
+ depends on ARM || SUPERH
help
This is a driver for SMSC's LAN911x series of Ethernet chipsets
including the new LAN9115, LAN9116, LAN9117, and LAN9118.
called smc911x. If you want to compile it as a module, say M
here and read <file:Documentation/kbuild/modules.txt>
+config SMSC911X
+ tristate "SMSC LAN911x/LAN921x families embedded ethernet support"
+ depends on ARM || SUPERH
+ select CRC32
+ select MII
+ select PHYLIB
+ ---help---
+ Say Y here if you want support for SMSC LAN911x and LAN921x families
+ of ethernet controllers.
+
+ To compile this driver as a module, choose M here and read
+ <file:Documentation/networking/net-modules.txt>. The module
+ will be called smsc911x.
+
config NET_VENDOR_RACAL
bool "Racal-Interlan (Micom) NI cards"
depends on ISA
config NE2000
tristate "NE2000/NE1000 support"
- depends on NET_ISA || (Q40 && m) || M32R || TOSHIBA_RBTX4927 || TOSHIBA_RBTX4938
+ depends on NET_ISA || (Q40 && m) || M32R || MACH_TX49XX
select CRC32
---help---
If you have a network (Ethernet) card of this type, say Y and read
To compile this driver as a module, choose M here. The module will
be called ibmveth.
-source "drivers/net/ibm_emac/Kconfig"
source "drivers/net/ibm_newemac/Kconfig"
config NET_PCI
To compile this driver as a module, choose M here. The module
will be called pcnet32.
-config PCNET32_NAPI
- bool "Use RX polling (NAPI)"
- depends on PCNET32
- help
- NAPI is a new driver API designed to reduce CPU and interrupt load
- when the driver is receiving lots of packets from the card. It is
- still somewhat experimental and thus not yet enabled by default.
-
- If your estimated Rx load is 10kpps or more, or if the card will be
- deployed on potentially unfriendly networks (e.g. in a firewall),
- then say Y here.
-
- If in doubt, say N.
-
config AMD8111_ETH
tristate "AMD 8111 (new PCI lance) support"
depends on NET_PCI && PCI
To compile this driver as a module, choose M here. The module
will be called amd8111e.
-config AMD8111E_NAPI
- bool "Use RX polling (NAPI)"
- depends on AMD8111_ETH
- help
- NAPI is a new driver API designed to reduce CPU and interrupt load
- when the driver is receiving lots of packets from the card. It is
- still somewhat experimental and thus not yet enabled by default.
-
- If your estimated Rx load is 10kpps or more, or if the card will be
- deployed on potentially unfriendly networks (e.g. in a firewall),
- then say Y here.
-
- If in doubt, say N.
-
config ADAPTEC_STARFIRE
tristate "Adaptec Starfire/DuraLAN support"
depends on NET_PCI && PCI
To compile this driver as a module, choose M here: the module
will be called starfire. This is recommended.
-config ADAPTEC_STARFIRE_NAPI
- bool "Use Rx Polling (NAPI) (EXPERIMENTAL)"
- depends on ADAPTEC_STARFIRE && EXPERIMENTAL
- help
- NAPI is a new driver API designed to reduce CPU and interrupt load
- when the driver is receiving lots of packets from the card. It is
- still somewhat experimental and thus not yet enabled by default.
-
- If your estimated Rx load is 10kpps or more, or if the card will be
- deployed on potentially unfriendly networks (e.g. in a firewall),
- then say Y here.
-
- If in doubt, say N.
-
config AC3200
tristate "Ansel Communications EISA 3200 support (EXPERIMENTAL)"
depends on NET_PCI && (ISA || EISA) && EXPERIMENTAL
config B44
tristate "Broadcom 440x/47xx ethernet support"
- depends on SSB_POSSIBLE
+ depends on SSB_POSSIBLE && HAS_DMA
select SSB
select MII
help
config CS89x0
tristate "CS89x0 support"
- depends on NET_PCI && (ISA || MACH_IXDP2351 || ARCH_IXDP2X01 || ARCH_PNX010X)
+ depends on NET_ETHERNET && (ISA || EISA || MACH_IXDP2351 \
+ || ARCH_IXDP2X01 || ARCH_PNX010X || MACH_MX31ADS)
---help---
Support for CS89x0 chipset based Ethernet cards. If you have a
network (Ethernet) card of this type, say Y and read the
To compile this driver as a module, choose M here. The module
will be called cs89x0.
+config CS89x0_NONISA_IRQ
+ def_bool y
+ depends on CS89x0 != n
+ depends on MACH_IXDP2351 || ARCH_IXDP2X01 || ARCH_PNX010X || MACH_MX31ADS
+
config TC35815
tristate "TOSHIBA TC35815 Ethernet support"
depends on NET_PCI && PCI && MIPS
select PHYLIB
-config EEPRO100
- tristate "EtherExpressPro/100 support (eepro100, original Becker driver)"
- depends on NET_PCI && PCI
- select MII
- help
- If you have an Intel EtherExpress PRO/100 PCI network (Ethernet)
- card, say Y and read the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>.
-
- To compile this driver as a module, choose M here. The module
- will be called eepro100.
-
-
config E100
tristate "Intel(R) PRO/100+ support"
depends on NET_PCI && PCI
More specific information and updates are available from
<http://www.scyld.com/network/epic100.html>.
+config SMSC9420
+ tristate "SMSC LAN9420 PCI ethernet adapter support"
+ depends on NET_PCI && PCI
+ select CRC32
+ select PHYLIB
+ select SMSC_PHY
+ help
+ This is a driver for SMSC's LAN9420 PCI ethernet adapter.
+ Say Y if you want it compiled into the kernel,
+ and read the Ethernet-HOWTO, available from
+ <http://www.linuxdoc.org/docs.html#howto>.
+
+ This driver is also available as a module. The module will be
+ called smsc9420. If you want to compile it as a module, say M
+ here and read <file:Documentation/kbuild/modules.txt>
+
config SUNDANCE
tristate "Sundance Alta support"
depends on NET_PCI && PCI
config TLAN
tristate "TI ThunderLAN support"
- depends on NET_PCI && (PCI || EISA) && !64BIT
+ depends on NET_PCI && (PCI || EISA)
---help---
If you have a PCI Ethernet network card based on the ThunderLAN chip
which is supported by this driver, say Y and read the
If unsure, say Y.
-config VIA_RHINE_NAPI
- bool "Use Rx Polling (NAPI)"
- depends on VIA_RHINE
- help
- NAPI is a new driver API designed to reduce CPU and interrupt load
- when the driver is receiving lots of packets from the card.
-
- If your estimated Rx load is 10kpps or more, or if the card will be
- deployed on potentially unfriendly networks (e.g. in a firewall),
- then say Y here.
-
-config LAN_SAA9730
- bool "Philips SAA9730 Ethernet support"
- depends on NET_PCI && PCI && MIPS_ATLAS
- help
- The SAA9730 is a combined multimedia and peripheral controller used
- in thin clients, Internet access terminals, and diskless
- workstations.
- See <http://www.semiconductors.philips.com/pip/SAA9730_flyer_1>.
-
config SC92031
tristate "Silan SC92031 PCI Fast Ethernet Adapter driver (EXPERIMENTAL)"
depends on NET_PCI && PCI && EXPERIMENTAL
config FEC_MPC52xx
tristate "MPC52xx FEC driver"
- depends on PPC_MERGE && PPC_MPC52xx && PPC_BESTCOMM_FEC
+ depends on PPC_MPC52xx && PPC_BESTCOMM
select CRC32
select PHYLIB
+ select PPC_BESTCOMM_FEC
---help---
This option enables support for the MPC5200's on-chip
Fast Ethernet Controller
Say Y here if you want to use the NE2000 compatible
controller on the Renesas H8/300 processor.
-source "drivers/net/fec_8xx/Kconfig"
+config ATL2
+ tristate "Atheros L2 Fast Ethernet support"
+ depends on PCI
+ select CRC32
+ select MII
+ help
+ This driver supports the Atheros L2 fast ethernet adapter.
+
+ To compile this driver as a module, choose M here. The module
+ will be called atl2.
+
source "drivers/net/fs_enet/Kconfig"
endif # NET_ETHERNET
To compile this driver as a module, choose M here. The module
will be called e1000.
-config E1000_NAPI
- bool "Use Rx Polling (NAPI)"
- depends on E1000
- help
- NAPI is a new driver API designed to reduce CPU and interrupt load
- when the driver is receiving lots of packets from the card. It is
- still somewhat experimental and thus not yet enabled by default.
-
- If your estimated Rx load is 10kpps or more, or if the card will be
- deployed on potentially unfriendly networks (e.g. in a firewall),
- then say Y here.
-
- If in doubt, say N.
-
-config E1000_DISABLE_PACKET_SPLIT
- bool "Disable Packet Split for PCI express adapters"
- depends on E1000
- help
- Say Y here if you want to use the legacy receive path for PCI express
- hardware.
-
- If in doubt, say N.
-
config E1000E
tristate "Intel(R) PRO/1000 PCI-Express Gigabit Ethernet support"
- depends on PCI
+ depends on PCI && (!SPARC32 || BROKEN)
---help---
This driver supports the PCI-Express Intel(R) PRO/1000 gigabit
ethernet family of adapters. For PCI or PCI-X e1000 adapters,
To compile this driver as a module, choose M here. The module
will be called e1000e.
-config E1000E_ENABLED
- def_bool E1000E != n
-
config IP1000
tristate "IP1000 Gigabit Ethernet support"
depends on PCI && EXPERIMENTAL
will be called ipg. This is recommended.
config IGB
- tristate "Intel(R) 82575 PCI-Express Gigabit Ethernet support"
+ tristate "Intel(R) 82575/82576 PCI-Express Gigabit Ethernet support"
depends on PCI
---help---
- This driver supports Intel(R) 82575 gigabit ethernet family of
+ This driver supports Intel(R) 82575/82576 gigabit ethernet family of
adapters. For more information on how to identify your adapter, go
to the Adapter & Driver ID Guide at:
To compile this driver as a module, choose M here. The module
will be called igb.
+config IGB_LRO
+ bool "Use software LRO"
+ depends on IGB && INET
+ select INET_LRO
+ ---help---
+ Say Y here if you want to use large receive offload.
+
+ If in doubt, say N.
+
+config IGB_DCA
+ bool "Direct Cache Access (DCA) Support"
+ default y
+ depends on IGB && DCA && !(IGB=y && DCA=m)
+ ---help---
+ Say Y here if you want to use Direct Cache Access (DCA) in the
+ driver. DCA is a method for warming the CPU cache before data
+ is used, with the intent of lessening the impact of cache misses.
+
source "drivers/net/ixp2000/Kconfig"
config MYRI_SBUS
tristate "Realtek 8169 gigabit ethernet support"
depends on PCI
select CRC32
+ select MII
---help---
Say Y here if you have a Realtek 8169 PCI Gigabit Ethernet adapter.
To compile this driver as a module, choose M here: the module
will be called r8169. This is recommended.
-config R8169_NAPI
- bool "Use Rx Polling (NAPI) (EXPERIMENTAL)"
- depends on R8169 && EXPERIMENTAL
- help
- NAPI is a new driver API designed to reduce CPU and interrupt load
- when the driver is receiving lots of packets from the card. It is
- still somewhat experimental and thus not yet enabled by default.
-
- If your estimated Rx load is 10kpps or more, or if the card will be
- deployed on potentially unfriendly networks (e.g. in a firewall),
- then say Y here.
-
- If in doubt, say N.
-
config R8169_VLAN
bool "VLAN support"
depends on R8169 && VLAN_8021Q
---help---
Say Y here for the r8169 driver to support the functions required
by the kernel 802.1Q code.
-
+
If in doubt, say Y.
config SB1250_MAC
config TIGON3
tristate "Broadcom Tigon3 support"
depends on PCI
+ select PHYLIB
help
This driver supports Broadcom Tigon3 based gigabit Ethernet cards.
the driver automatically distinguishes the models, you can
safely enable this option even if you have a wireless-less model.
+config GELIC_WIRELESS_OLD_PSK_INTERFACE
+ bool "PS3 Wireless private PSK interface (OBSOLETE)"
+ depends on GELIC_WIRELESS
+ help
+ This option retains the obsolete private interface to pass
+ the PSK from user space programs to the driver. The PSK
+ stands for 'Pre Shared Key' and is used for WPA[2]-PSK
+ (WPA-Personal) environment.
+ If WPA[2]-PSK is used and you need to use old programs that
+ support only this old interface, say Y. Otherwise N.
+
+ If unsure, say N.
+
config GIANFAR
tristate "Gianfar Ethernet"
depends on FSL_SOC
This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx,
and MPC86xx family of chips, and the FEC on the 8540.
-config GFAR_NAPI
- bool "Use Rx Polling (NAPI)"
- depends on GIANFAR
-
config UCC_GETH
tristate "Freescale QE Gigabit Ethernet"
depends on QUICC_ENGINE
This driver supports the Gigabit Ethernet mode of the QUICC Engine,
which is available on some Freescale SOCs.
-config UGETH_NAPI
- bool "Use Rx Polling (NAPI)"
- depends on UCC_GETH
-
config UGETH_MAGIC_PACKET
bool "Magic Packet detection support"
depends on UCC_GETH
-config UGETH_FILTERING
- bool "Mac address filtering support"
- depends on UCC_GETH
-
config UGETH_TX_ON_DEMAND
bool "Transmit on Demand support"
depends on UCC_GETH
config MV643XX_ETH
tristate "Marvell Discovery (643XX) and Orion ethernet support"
depends on MV64360 || MV64X60 || (PPC_MULTIPLATFORM && PPC32) || PLAT_ORION
- select MII
+ select PHYLIB
help
This driver supports the gigabit ethernet MACs in the
Marvell Discovery PPC/MIPS chipset family (MV643XX) and
will be called qla3xxx.
config ATL1
- tristate "Attansic L1 Gigabit Ethernet support (EXPERIMENTAL)"
- depends on PCI && EXPERIMENTAL
+ tristate "Atheros/Attansic L1 Gigabit Ethernet support"
+ depends on PCI
select CRC32
select MII
help
- This driver supports the Attansic L1 gigabit ethernet adapter.
+ This driver supports the Atheros/Attansic L1 gigabit ethernet
+ adapter.
To compile this driver as a module, choose M here. The module
will be called atl1.
+config ATL1E
+ tristate "Atheros L1E Gigabit Ethernet support (EXPERIMENTAL)"
+ depends on PCI && EXPERIMENTAL
+ select CRC32
+ select MII
+ help
+ This driver supports the Atheros L1E gigabit ethernet adapter.
+
+ To compile this driver as a module, choose M here. The module
+ will be called atl1e.
+
+config JME
+ tristate "JMicron(R) PCI-Express Gigabit Ethernet support"
+ depends on PCI
+ select CRC32
+ select MII
+ ---help---
+ This driver supports the PCI-Express gigabit ethernet adapters
+ based on JMicron JMC250 chipset.
+
+ To compile this driver as a module, choose M here. The module
+ will be called jme.
+
endif # NETDEV_1000
#
Enables support for Chelsio's gigabit Ethernet PCI cards. If you
are using only 10G cards say 'N' here.
-config CHELSIO_T1_NAPI
- bool "Use Rx Polling (NAPI)"
- depends on CHELSIO_T1
+config CHELSIO_T3_DEPENDS
+ tristate
+ depends on PCI && INET
default y
- help
- NAPI is a driver API designed to reduce CPU and interrupt load
- when the driver is receiving lots of packets from the card.
config CHELSIO_T3
tristate "Chelsio Communications T3 10Gb Ethernet support"
- depends on PCI
+ depends on CHELSIO_T3_DEPENDS
select FW_LOADER
+ select INET_LRO
help
This driver supports Chelsio T3-based gigabit and 10Gb Ethernet
adapters.
To compile the driver as a module, choose M here. The module
will be called ehea.
+config ENIC
+ tristate "Cisco 10G Ethernet NIC support"
+ depends on PCI && INET
+ select INET_LRO
+ help
+ This enables the support for the Cisco 10G Ethernet card.
+
config IXGBE
tristate "Intel(R) 10GbE PCI Express adapters support"
- depends on PCI
+ depends on PCI && INET
+ select INET_LRO
---help---
This driver supports Intel(R) 10GbE PCI Express family of
adapters. For more information on how to identify your adapter, go
To compile this driver as a module, choose M here. The module
will be called ixgbe.
+config IXGBE_DCA
+ bool "Direct Cache Access (DCA) Support"
+ default y
+ depends on IXGBE && DCA && !(IXGBE=y && DCA=m)
+ ---help---
+ Say Y here if you want to use Direct Cache Access (DCA) in the
+ driver. DCA is a method for warming the CPU cache before data
+ is used, with the intent of lessening the impact of cache misses.
+
+config IXGBE_DCB
+ bool "Data Center Bridging (DCB) Support"
+ default n
+ depends on IXGBE && DCB
+ ---help---
+ Say Y here if you want to use Data Center Bridging (DCB) in the
+ driver.
+
+ If unsure, say N.
+
config IXGB
tristate "Intel(R) PRO/10GbE support"
depends on PCI
To compile this driver as a module, choose M here. The module
will be called ixgb.
-config IXGB_NAPI
- bool "Use Rx Polling (NAPI) (EXPERIMENTAL)"
- depends on IXGB && EXPERIMENTAL
- help
- NAPI is a new driver API designed to reduce CPU and interrupt load
- when the driver is receiving lots of packets from the card. It is
- still somewhat experimental and thus not yet enabled by default.
-
- If your estimated Rx load is 10kpps or more, or if the card will be
- deployed on potentially unfriendly networks (e.g. in a firewall),
- then say Y here.
-
- If in doubt, say N.
-
config S2IO
tristate "S2IO 10Gbe XFrame NIC"
depends on PCI
More specific information on configuring the driver is in
<file:Documentation/networking/s2io.txt>.
-config S2IO_NAPI
- bool "Use Rx Polling (NAPI) (EXPERIMENTAL)"
- depends on S2IO && EXPERIMENTAL
- help
- NAPI is a new driver API designed to reduce CPU and interrupt load
- when the driver is receiving lots of packets from the card. It is
- still somewhat experimental and thus not yet enabled by default.
-
- If your estimated Rx load is 10kpps or more, or if the card will be
- deployed on potentially unfriendly networks (e.g. in a firewall),
- then say Y here.
-
- If in doubt, say N.
-
config MYRI10GE
tristate "Myricom Myri-10G Ethernet support"
depends on PCI && INET
To compile this driver as a module, choose M here. The module
will be called myri10ge.
+config MYRI10GE_DCA
+ bool "Direct Cache Access (DCA) Support"
+ default y
+ depends on MYRI10GE && DCA && !(MYRI10GE=y && DCA=m)
+ ---help---
+ Say Y here if you want to use Direct Cache Access (DCA) in the
+ driver. DCA is a method for warming the CPU cache before data
+ is used, with the intent of lessening the impact of cache misses.
+
config NETXEN_NIC
tristate "NetXen Multi port (1/10) Gigabit Ethernet NIC"
depends on PCI
This driver supports the on-chip 1/10Gbit Ethernet controller on
PA Semi's PWRficient line of chips.
+config MLX4_EN
+ tristate "Mellanox Technologies 10Gbit Ethernet support"
+ depends on PCI && INET
+ select MLX4_CORE
+ select INET_LRO
+ help
+ This driver supports Mellanox Technologies ConnectX Ethernet
+ devices.
+
config MLX4_CORE
tristate
depends on PCI
tristate "Broadcom NetXtremeII 10Gb support"
depends on PCI
select ZLIB_INFLATE
+ select LIBCRC32C
help
This driver supports Broadcom NetXtremeII 10 gigabit Ethernet cards.
To compile this driver as a module, choose M here: the module
will be called bnx2x. This is recommended.
+config QLGE
+ tristate "QLogic QLGE 10Gb Ethernet Driver Support"
+ depends on PCI
+ help
+ This driver supports QLogic ISP8XXX 10Gb Ethernet cards.
+
+ To compile this driver as a module, choose M here: the module
+ will be called qlge.
+
+source "drivers/net/sfc/Kconfig"
endif # NETDEV_10000
source "drivers/net/wireless/Kconfig"
+source "drivers/net/wimax/Kconfig"
+
source "drivers/net/usb/Kconfig"
source "drivers/net/pcmcia/Kconfig"
default "128"
config FDDI
- bool "FDDI driver support"
+ tristate "FDDI driver support"
depends on (PCI || EISA || TC)
help
Fiber Distributed Data Interface is a high speed local area network
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff