#ifndef MODULE
struct net_device * __init el2_probe(int unit)
{
- struct net_device *dev = alloc_ei_netdev();
+ struct net_device *dev = alloc_eip_netdev();
int err;
if (!dev)
}
#endif
+static const struct net_device_ops el2_netdev_ops = {
+ .ndo_open = el2_open,
+ .ndo_stop = el2_close,
+
+ .ndo_start_xmit = eip_start_xmit,
+ .ndo_tx_timeout = eip_tx_timeout,
+ .ndo_get_stats = eip_get_stats,
+ .ndo_set_multicast_list = eip_set_multicast_list,
+ .ndo_validate_addr = eth_validate_addr,
+ .ndo_set_mac_address = eth_mac_addr,
+ .ndo_change_mtu = eth_change_mtu,
+#ifdef CONFIG_NET_POLL_CONTROLLER
+ .ndo_poll_controller = eip_poll,
+#endif
+};
+
/* Probe for the Etherlink II card at I/O port base IOADDR,
returning non-zero on success. If found, set the station
address and memory parameters in DEVICE. */
iobase_reg = inb(ioaddr+0x403);
membase_reg = inb(ioaddr+0x404);
/* ASIC location registers should be 0 or have only a single bit set. */
- if ( (iobase_reg & (iobase_reg - 1))
- || (membase_reg & (membase_reg - 1))) {
+ if ((iobase_reg & (iobase_reg - 1)) ||
+ (membase_reg & (membase_reg - 1))) {
retval = -ENODEV;
goto out1;
}
}
if (ei_debug && version_printed++ == 0)
- printk(version);
+ pr_debug("%s", version);
dev->base_addr = ioaddr;
- printk("%s: 3c503 at i/o base %#3x, node ", dev->name, ioaddr);
+ pr_info("%s: 3c503 at i/o base %#3x, node ", dev->name, ioaddr);
/* Retrieve and print the ethernet address. */
for (i = 0; i < 6; i++)
- printk(" %2.2x", dev->dev_addr[i] = inb(ioaddr + i));
+ dev->dev_addr[i] = inb(ioaddr + i);
+ pr_cont("%pM", dev->dev_addr);
/* Map the 8390 back into the window. */
outb(ECNTRL_THIN, ioaddr + 0x406);
outb_p(E8390_PAGE0, ioaddr + E8390_CMD);
/* Probe for, turn on and clear the board's shared memory. */
- if (ei_debug > 2) printk(" memory jumpers %2.2x ", membase_reg);
+ if (ei_debug > 2)
+ pr_cont(" memory jumpers %2.2x ", membase_reg);
outb(EGACFR_NORM, ioaddr + 0x405); /* Enable RAM */
/* This should be probed for (or set via an ioctl()) at run-time.
#else
ei_status.interface_num = dev->mem_end & 0xf;
#endif
- printk(", using %sternal xcvr.\n", ei_status.interface_num == 0 ? "in" : "ex");
+ pr_cont(", using %sternal xcvr.\n", ei_status.interface_num == 0 ? "in" : "ex");
if ((membase_reg & 0xf0) == 0) {
dev->mem_start = 0;
writel(0xba5eba5e, mem_base);
for (i = sizeof(test_val); i < EL2_MEMSIZE; i+=sizeof(test_val)) {
writel(test_val, mem_base + i);
- if (readl(mem_base) != 0xba5eba5e
- || readl(mem_base + i) != test_val) {
- printk("3c503: memory failure or memory address conflict.\n");
+ if (readl(mem_base) != 0xba5eba5e ||
+ readl(mem_base + i) != test_val) {
+ pr_warning("3c503: memory failure or memory address conflict.\n");
dev->mem_start = 0;
ei_status.name = "3c503-PIO";
iounmap(mem_base);
if (dev->irq == 2)
dev->irq = 9;
else if (dev->irq > 5 && dev->irq != 9) {
- printk("3c503: configured interrupt %d invalid, will use autoIRQ.\n",
+ pr_warning("3c503: configured interrupt %d invalid, will use autoIRQ.\n",
dev->irq);
dev->irq = 0;
}
ei_status.saved_irq = dev->irq;
- dev->open = &el2_open;
- dev->stop = &el2_close;
+ dev->netdev_ops = &el2_netdev_ops;
dev->ethtool_ops = &netdev_ethtool_ops;
-#ifdef CONFIG_NET_POLL_CONTROLLER
- dev->poll_controller = ei_poll;
-#endif
retval = register_netdev(dev);
if (retval)
goto out1;
if (dev->mem_start)
- printk("%s: %s - %dkB RAM, 8kB shared mem window at %#6lx-%#6lx.\n",
+ pr_info("%s: %s - %dkB RAM, 8kB shared mem window at %#6lx-%#6lx.\n",
dev->name, ei_status.name, (wordlength+1)<<3,
dev->mem_start, dev->mem_end-1);
{
ei_status.tx_start_page = EL2_MB1_START_PG;
ei_status.rx_start_page = EL2_MB1_START_PG + TX_PAGES;
- printk("\n%s: %s, %dkB RAM, using programmed I/O (REJUMPER for SHARED MEMORY).\n",
+ pr_info("%s: %s, %dkB RAM, using programmed I/O (REJUMPER for SHARED MEMORY).\n",
dev->name, ei_status.name, (wordlength+1)<<3);
}
release_region(ioaddr + 0x400, 8);
return retval;
}
+static irqreturn_t el2_probe_interrupt(int irq, void *seen)
+{
+ *(bool *)seen = true;
+ return IRQ_HANDLED;
+}
+
static int
el2_open(struct net_device *dev)
{
- int retval = -EAGAIN;
+ int retval;
if (dev->irq < 2) {
int irqlist[] = {5, 9, 3, 4, 0};
outb(EGACFR_NORM, E33G_GACFR); /* Enable RAM and interrupts. */
do {
- if (request_irq (*irqp, NULL, 0, "bogus", dev) != -EBUSY) {
+ bool seen;
+
+ retval = request_irq(*irqp, el2_probe_interrupt, 0,
+ dev->name, &seen);
+ if (retval == -EBUSY)
+ continue;
+ if (retval < 0)
+ goto err_disable;
+
/* Twinkle the interrupt, and check if it's seen. */
- unsigned long cookie = probe_irq_on();
+ seen = false;
+ smp_wmb();
outb_p(0x04 << ((*irqp == 9) ? 2 : *irqp), E33G_IDCFR);
outb_p(0x00, E33G_IDCFR);
- if (*irqp == probe_irq_off(cookie) /* It's a good IRQ line! */
- && ((retval = request_irq(dev->irq = *irqp,
- ei_interrupt, 0, dev->name, dev)) == 0))
- break;
- }
+ msleep(1);
+ free_irq(*irqp, el2_probe_interrupt);
+ if (!seen)
+ continue;
+
+ retval = request_irq(dev->irq = *irqp, eip_interrupt, 0,
+ dev->name, dev);
+ if (retval == -EBUSY)
+ continue;
+ if (retval < 0)
+ goto err_disable;
} while (*++irqp);
+
if (*irqp == 0) {
+ err_disable:
outb(EGACFR_IRQOFF, E33G_GACFR); /* disable interrupts. */
- return retval;
+ return -EAGAIN;
}
} else {
- if ((retval = request_irq(dev->irq, ei_interrupt, 0, dev->name, dev))) {
+ if ((retval = request_irq(dev->irq, eip_interrupt, 0, dev->name, dev))) {
return retval;
}
}
el2_init_card(dev);
- ei_open(dev);
+ eip_open(dev);
return 0;
}
dev->irq = ei_status.saved_irq;
outb(EGACFR_IRQOFF, E33G_GACFR); /* disable interrupts. */
- ei_close(dev);
+ eip_close(dev);
return 0;
}
el2_reset_8390(struct net_device *dev)
{
if (ei_debug > 1) {
- printk("%s: Resetting the 3c503 board...", dev->name);
- printk("%#lx=%#02x %#lx=%#02x %#lx=%#02x...", E33G_IDCFR, inb(E33G_IDCFR),
+ pr_debug("%s: Resetting the 3c503 board...", dev->name);
+ pr_cont(" %#lx=%#02x %#lx=%#02x %#lx=%#02x...", E33G_IDCFR, inb(E33G_IDCFR),
E33G_CNTRL, inb(E33G_CNTRL), E33G_GACFR, inb(E33G_GACFR));
}
outb_p(ECNTRL_RESET|ECNTRL_THIN, E33G_CNTRL);
ei_status.txing = 0;
outb_p(ei_status.interface_num==0 ? ECNTRL_THIN : ECNTRL_AUI, E33G_CNTRL);
el2_init_card(dev);
- if (ei_debug > 1) printk("done\n");
+ if (ei_debug > 1)
+ pr_cont("done\n");
}
/* Initialize the 3c503 GA registers after a reset. */
{
if(!boguscount--)
{
- printk("%s: FIFO blocked in el2_block_output.\n", dev->name);
+ pr_notice("%s: FIFO blocked in el2_block_output.\n", dev->name);
el2_reset_8390(dev);
goto blocked;
}
}
blocked:;
outb_p(ei_status.interface_num==0 ? ECNTRL_THIN : ECNTRL_AUI, E33G_CNTRL);
- return;
}
/* Read the 4 byte, page aligned 8390 specific header. */
{
if(!boguscount--)
{
- printk("%s: FIFO blocked in el2_get_8390_hdr.\n", dev->name);
+ pr_notice("%s: FIFO blocked in el2_get_8390_hdr.\n", dev->name);
memset(hdr, 0x00, sizeof(struct e8390_pkt_hdr));
el2_reset_8390(dev);
goto blocked;
{
if(!boguscount--)
{
- printk("%s: FIFO blocked in el2_block_input.\n", dev->name);
+ pr_notice("%s: FIFO blocked in el2_block_input.\n", dev->name);
el2_reset_8390(dev);
goto blocked;
}
}
blocked:;
outb_p(ei_status.interface_num == 0 ? ECNTRL_THIN : ECNTRL_AUI, E33G_CNTRL);
- return;
}
for (this_dev = 0; this_dev < MAX_EL2_CARDS; this_dev++) {
if (io[this_dev] == 0) {
if (this_dev != 0) break; /* only autoprobe 1st one */
- printk(KERN_NOTICE "3c503.c: Presently autoprobing (not recommended) for a single card.\n");
+ pr_notice("3c503.c: Presently autoprobing (not recommended) for a single card.\n");
}
- dev = alloc_ei_netdev();
+ dev = alloc_eip_netdev();
if (!dev)
break;
dev->irq = irq[this_dev];
continue;
}
free_netdev(dev);
- printk(KERN_WARNING "3c503.c: No 3c503 card found (i/o = 0x%x).\n", io[this_dev]);
+ pr_warning("3c503.c: No 3c503 card found (i/o = 0x%x).\n", io[this_dev]);
break;
}
if (found)
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff