#include <linux/clk.h>
#include <linux/err.h>
#include <linux/mmc/host.h>
+#include <linux/io.h>
+#include <linux/regulator/consumer.h>
+#include <linux/gpio.h>
-#include <asm/dma.h>
-#include <asm/io.h>
#include <asm/sizes.h>
-#include <asm/arch/pxa-regs.h>
-#include <asm/arch/mmc.h>
+#include <mach/hardware.h>
+#include <mach/dma.h>
+#include <mach/mmc.h>
#include "pxamci.h"
#define NR_SG 1
#define CLKRT_OFF (~0)
+#define mmc_has_26MHz() (cpu_is_pxa300() || cpu_is_pxa310() \
+ || cpu_is_pxa935())
+
struct pxamci_host {
struct mmc_host *mmc;
spinlock_t lock;
unsigned int dma_dir;
unsigned int dma_drcmrrx;
unsigned int dma_drcmrtx;
+
+ struct regulator *vcc;
};
+static inline void pxamci_init_ocr(struct pxamci_host *host)
+{
+#ifdef CONFIG_REGULATOR
+ host->vcc = regulator_get(mmc_dev(host->mmc), "vmmc");
+
+ if (IS_ERR(host->vcc))
+ host->vcc = NULL;
+ else {
+ host->mmc->ocr_avail = mmc_regulator_get_ocrmask(host->vcc);
+ if (host->pdata && host->pdata->ocr_mask)
+ dev_warn(mmc_dev(host->mmc),
+ "ocr_mask/setpower will not be used\n");
+ }
+#endif
+ if (host->vcc == NULL) {
+ /* fall-back to platform data */
+ host->mmc->ocr_avail = host->pdata ?
+ host->pdata->ocr_mask :
+ MMC_VDD_32_33 | MMC_VDD_33_34;
+ }
+}
+
+static inline void pxamci_set_power(struct pxamci_host *host, unsigned int vdd)
+{
+ int on;
+
+#ifdef CONFIG_REGULATOR
+ if (host->vcc)
+ mmc_regulator_set_ocr(host->vcc, vdd);
+#endif
+ if (!host->vcc && host->pdata &&
+ gpio_is_valid(host->pdata->gpio_power)) {
+ on = ((1 << vdd) & host->pdata->ocr_mask);
+ gpio_set_value(host->pdata->gpio_power,
+ !!on ^ host->pdata->gpio_power_invert);
+ }
+ if (!host->vcc && host->pdata && host->pdata->setpower)
+ host->pdata->setpower(mmc_dev(host->mmc), vdd);
+}
+
static void pxamci_stop_clock(struct pxamci_host *host)
{
if (readl(host->base + MMC_STAT) & STAT_CLK_EN) {
if (data->flags & MMC_DATA_READ) {
host->dma_dir = DMA_FROM_DEVICE;
- dcmd = DCMD_INCTRGADDR | DCMD_FLOWTRG;
+ dcmd = DCMD_INCTRGADDR | DCMD_FLOWSRC;
DRCMR(host->dma_drcmrtx) = 0;
DRCMR(host->dma_drcmrrx) = host->dma | DRCMR_MAPVLD;
} else {
host->dma_dir = DMA_TO_DEVICE;
- dcmd = DCMD_INCSRCADDR | DCMD_FLOWSRC;
+ dcmd = DCMD_INCSRCADDR | DCMD_FLOWTRG;
DRCMR(host->dma_drcmrrx) = 0;
DRCMR(host->dma_drcmrtx) = host->dma | DRCMR_MAPVLD;
}
if (dalgn)
DALGN |= (1 << host->dma);
else
- DALGN &= (1 << host->dma);
+ DALGN &= ~(1 << host->dma);
DDADR(host->dma) = host->sg_dma;
- DCSR(host->dma) = DCSR_RUN;
+
+ /*
+ * workaround for erratum #91:
+ * only start DMA now if we are doing a read,
+ * otherwise we wait until CMD/RESP has finished
+ * before starting DMA.
+ */
+ if (!cpu_is_pxa27x() || data->flags & MMC_DATA_READ)
+ DCSR(host->dma) = DCSR_RUN;
}
static void pxamci_start_cmd(struct pxamci_host *host, struct mmc_command *cmd, unsigned int cmdat)
if (stat & STAT_TIME_OUT_RESPONSE) {
cmd->error = -ETIMEDOUT;
} else if (stat & STAT_RES_CRC_ERR && cmd->flags & MMC_RSP_CRC) {
-#ifdef CONFIG_PXA27x
/*
* workaround for erratum #42:
* Intel PXA27x Family Processor Specification Update Rev 001
* A bogus CRC error can appear if the msb of a 136 bit
* response is a one.
*/
- if (cmd->flags & MMC_RSP_136 && cmd->resp[0] & 0x80000000) {
+ if (cpu_is_pxa27x() &&
+ (cmd->flags & MMC_RSP_136 && cmd->resp[0] & 0x80000000))
pr_debug("ignoring CRC from command %d - *risky*\n", cmd->opcode);
- } else
-#endif
- cmd->error = -EILSEQ;
+ else
+ cmd->error = -EILSEQ;
}
pxamci_disable_irq(host, END_CMD_RES);
if (host->data && !cmd->error) {
pxamci_enable_irq(host, DATA_TRAN_DONE);
+ /*
+ * workaround for erratum #91, if doing write
+ * enable DMA late
+ */
+ if (cpu_is_pxa27x() && host->data->flags & MMC_DATA_WRITE)
+ DCSR(host->dma) = DCSR_RUN;
} else {
pxamci_finish_request(host, host->mrq);
}
return 0;
DCSR(host->dma) = 0;
- dma_unmap_sg(mmc_dev(host->mmc), data->sg, host->dma_len,
+ dma_unmap_sg(mmc_dev(host->mmc), data->sg, data->sg_len,
host->dma_dir);
if (stat & STAT_READ_TIME_OUT)
{
struct pxamci_host *host = mmc_priv(mmc);
+ if (host->pdata && gpio_is_valid(host->pdata->gpio_card_ro)) {
+ if (host->pdata->gpio_card_ro_invert)
+ return !gpio_get_value(host->pdata->gpio_card_ro);
+ else
+ return gpio_get_value(host->pdata->gpio_card_ro);
+ }
if (host->pdata && host->pdata->get_ro)
return !!host->pdata->get_ro(mmc_dev(mmc));
/*
clk_enable(host->clk);
if (ios->clock == 26000000) {
- /* to support 26MHz on pxa300/pxa310 */
+ /* to support 26MHz */
host->clkrt = 7;
} else {
/* to handle (19.5MHz, 26MHz) */
if (host->power_mode != ios->power_mode) {
host->power_mode = ios->power_mode;
- if (host->pdata && host->pdata->setpower)
- host->pdata->setpower(mmc_dev(mmc), ios->vdd);
+ pxamci_set_power(host, ios->vdd);
if (ios->power_mode == MMC_POWER_ON)
host->cmdat |= CMDAT_INIT;
struct mmc_host *mmc;
struct pxamci_host *host = NULL;
struct resource *r, *dmarx, *dmatx;
- int ret, irq;
+ int ret, irq, gpio_cd = -1, gpio_ro = -1, gpio_power = -1;
r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
irq = platform_get_irq(pdev, 0);
/*
* Block length register is only 10 bits before PXA27x.
*/
- mmc->max_blk_size = (cpu_is_pxa21x() || cpu_is_pxa25x()) ? 1023 : 2048;
+ mmc->max_blk_size = cpu_is_pxa25x() ? 1023 : 2048;
/*
* Block count register is 16 bits.
host->pdata = pdev->dev.platform_data;
host->clkrt = CLKRT_OFF;
- host->clk = clk_get(&pdev->dev, "MMCCLK");
+ host->clk = clk_get(&pdev->dev, NULL);
if (IS_ERR(host->clk)) {
ret = PTR_ERR(host->clk);
host->clk = NULL;
* Calculate minimum clock rate, rounding up.
*/
mmc->f_min = (host->clkrate + 63) / 64;
- mmc->f_max = (cpu_is_pxa300() || cpu_is_pxa310()) ? 26000000
- : host->clkrate;
+ mmc->f_max = (mmc_has_26MHz()) ? 26000000 : host->clkrate;
+
+ pxamci_init_ocr(host);
- mmc->ocr_avail = host->pdata ?
- host->pdata->ocr_mask :
- MMC_VDD_32_33|MMC_VDD_33_34;
mmc->caps = 0;
host->cmdat = 0;
- if (!cpu_is_pxa21x() && !cpu_is_pxa25x()) {
+ if (!cpu_is_pxa25x()) {
mmc->caps |= MMC_CAP_4_BIT_DATA | MMC_CAP_SDIO_IRQ;
host->cmdat |= CMDAT_SDIO_INT_EN;
- if (cpu_is_pxa300() || cpu_is_pxa310())
+ if (mmc_has_26MHz())
mmc->caps |= MMC_CAP_MMC_HIGHSPEED |
MMC_CAP_SD_HIGHSPEED;
}
}
host->dma_drcmrtx = dmatx->start;
+ if (host->pdata) {
+ gpio_cd = host->pdata->gpio_card_detect;
+ gpio_ro = host->pdata->gpio_card_ro;
+ gpio_power = host->pdata->gpio_power;
+ }
+ if (gpio_is_valid(gpio_power)) {
+ ret = gpio_request(gpio_power, "mmc card power");
+ if (ret) {
+ dev_err(&pdev->dev, "Failed requesting gpio_power %d\n", gpio_power);
+ goto out;
+ }
+ gpio_direction_output(gpio_power,
+ host->pdata->gpio_power_invert);
+ }
+ if (gpio_is_valid(gpio_ro)) {
+ ret = gpio_request(gpio_ro, "mmc card read only");
+ if (ret) {
+ dev_err(&pdev->dev, "Failed requesting gpio_ro %d\n", gpio_ro);
+ goto err_gpio_ro;
+ }
+ gpio_direction_input(gpio_ro);
+ }
+ if (gpio_is_valid(gpio_cd)) {
+ ret = gpio_request(gpio_cd, "mmc card detect");
+ if (ret) {
+ dev_err(&pdev->dev, "Failed requesting gpio_cd %d\n", gpio_cd);
+ goto err_gpio_cd;
+ }
+ gpio_direction_input(gpio_cd);
+
+ ret = request_irq(gpio_to_irq(gpio_cd), pxamci_detect_irq,
+ IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
+ "mmc card detect", mmc);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to request card detect IRQ\n");
+ goto err_request_irq;
+ }
+ }
+
if (host->pdata && host->pdata->init)
host->pdata->init(&pdev->dev, pxamci_detect_irq, mmc);
+ if (gpio_is_valid(gpio_power) && host->pdata->setpower)
+ dev_warn(&pdev->dev, "gpio_power and setpower() both defined\n");
+ if (gpio_is_valid(gpio_ro) && host->pdata->get_ro)
+ dev_warn(&pdev->dev, "gpio_ro and get_ro() both defined\n");
+
mmc_add_host(mmc);
return 0;
+err_request_irq:
+ gpio_free(gpio_cd);
+err_gpio_cd:
+ gpio_free(gpio_ro);
+err_gpio_ro:
+ gpio_free(gpio_power);
out:
if (host) {
if (host->dma >= 0)
static int pxamci_remove(struct platform_device *pdev)
{
struct mmc_host *mmc = platform_get_drvdata(pdev);
+ int gpio_cd = -1, gpio_ro = -1, gpio_power = -1;
platform_set_drvdata(pdev, NULL);
if (mmc) {
struct pxamci_host *host = mmc_priv(mmc);
+ mmc_remove_host(mmc);
+
+ if (host->pdata) {
+ gpio_cd = host->pdata->gpio_card_detect;
+ gpio_ro = host->pdata->gpio_card_ro;
+ gpio_power = host->pdata->gpio_power;
+ }
+ if (gpio_is_valid(gpio_cd)) {
+ free_irq(gpio_to_irq(gpio_cd), mmc);
+ gpio_free(gpio_cd);
+ }
+ if (gpio_is_valid(gpio_ro))
+ gpio_free(gpio_ro);
+ if (gpio_is_valid(gpio_power))
+ gpio_free(gpio_power);
+ if (host->vcc)
+ regulator_put(host->vcc);
+
if (host->pdata && host->pdata->exit)
host->pdata->exit(&pdev->dev, mmc);
- mmc_remove_host(mmc);
-
pxamci_stop_clock(host);
writel(TXFIFO_WR_REQ|RXFIFO_RD_REQ|CLK_IS_OFF|STOP_CMD|
END_CMD_RES|PRG_DONE|DATA_TRAN_DONE,
}
#ifdef CONFIG_PM
-static int pxamci_suspend(struct platform_device *dev, pm_message_t state)
+static int pxamci_suspend(struct device *dev)
{
- struct mmc_host *mmc = platform_get_drvdata(dev);
+ struct mmc_host *mmc = dev_get_drvdata(dev);
int ret = 0;
if (mmc)
- ret = mmc_suspend_host(mmc, state);
+ ret = mmc_suspend_host(mmc, PMSG_SUSPEND);
return ret;
}
-static int pxamci_resume(struct platform_device *dev)
+static int pxamci_resume(struct device *dev)
{
- struct mmc_host *mmc = platform_get_drvdata(dev);
+ struct mmc_host *mmc = dev_get_drvdata(dev);
int ret = 0;
if (mmc)
return ret;
}
-#else
-#define pxamci_suspend NULL
-#define pxamci_resume NULL
+
+static const struct dev_pm_ops pxamci_pm_ops = {
+ .suspend = pxamci_suspend,
+ .resume = pxamci_resume,
+};
#endif
static struct platform_driver pxamci_driver = {
.probe = pxamci_probe,
.remove = pxamci_remove,
- .suspend = pxamci_suspend,
- .resume = pxamci_resume,
.driver = {
.name = DRIVER_NAME,
.owner = THIS_MODULE,
+#ifdef CONFIG_PM
+ .pm = &pxamci_pm_ops,
+#endif
},
};
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff