if MISC_DEVICES
+config AD525X_DPOT
+ tristate "Analog Devices AD525x Digital Potentiometers"
+ depends on I2C && SYSFS
+ help
+ If you say yes here, you get support for the Analog Devices
+ AD5258, AD5259, AD5251, AD5252, AD5253, AD5254 and AD5255
+ digital potentiometer chips.
+
+ See Documentation/misc-devices/ad525x_dpot.txt for the
+ userspace interface.
+
+ This driver can also be built as a module. If so, the module
+ will be called ad525x_dpot.
+
config ATMEL_PWM
tristate "Atmel AT32/AT91 PWM support"
- depends on AVR32 || ARCH_AT91
+ depends on AVR32 || ARCH_AT91SAM9263 || ARCH_AT91SAM9RL || ARCH_AT91CAP9
help
This option enables device driver support for the PWM channels
- on certain Atmel prcoessors. Pulse Width Modulation is used for
- purposes including software controlled power-efficent backlights
+ on certain Atmel processors. Pulse Width Modulation is used for
+ purposes including software controlled power-efficient backlights
on LCD displays, motor control, and waveform generation.
+config ATMEL_TCLIB
+ bool "Atmel AT32/AT91 Timer/Counter Library"
+ depends on (AVR32 || ARCH_AT91)
+ help
+ Select this if you want a library to allocate the Timer/Counter
+ blocks found on many Atmel processors. This facilitates using
+ these blocks by different drivers despite processor differences.
+
+config ATMEL_TCB_CLKSRC
+ bool "TC Block Clocksource"
+ depends on ATMEL_TCLIB && GENERIC_TIME
+ default y
+ help
+ Select this to get a high precision clocksource based on a
+ TC block with a 5+ MHz base clock rate. Two timer channels
+ are combined to make a single 32-bit timer.
+
+ When GENERIC_CLOCKEVENTS is defined, the third timer channel
+ may be used as a clock event device supporting oneshot mode
+ (delays of up to two seconds) based on the 32 KiHz clock.
+
+config ATMEL_TCB_CLKSRC_BLOCK
+ int
+ depends on ATMEL_TCB_CLKSRC
+ prompt "TC Block" if ARCH_AT91RM9200 || ARCH_AT91SAM9260 || CPU_AT32AP700X
+ default 0
+ range 0 1
+ help
+ Some chips provide more than one TC block, so you have the
+ choice of which one to use for the clock framework. The other
+ TC can be used for other purposes, such as PWM generation and
+ interval timing.
+
config IBM_ASM
tristate "Device driver for IBM RSA service processor"
depends on X86 && PCI && INPUT && EXPERIMENTAL
for your IBM server.
config PHANTOM
- tristate "Sensable PHANToM"
+ tristate "Sensable PHANToM (PCI)"
depends on PCI
help
Say Y here if you want to build a driver for Sensable PHANToM device.
+ This driver is only for PCI PHANToMs.
+
If you choose to build module, its name will be phantom. If unsure,
say N here.
-config EEPROM_93CX6
- tristate "EEPROM 93CX6 support"
- ---help---
- This is a driver for the EEPROM chipsets 93c46 and 93c66.
- The driver supports both read as well as write commands.
-
- If unsure, say N.
-
config SGI_IOC4
tristate "SGI IOC4 Base IO support"
depends on PCI
cards are supported via 'MMC/SD Card support: TI Flash Media MMC/SD
Interface support (MMC_TIFM_SD)'.
- To compile this driver as a module, choose M here: the module will
+ To compile this driver as a module, choose M here: the module will
be called tifm_core.
config TIFM_7XX1
To make actual use of the device, you will have to select some
flash card format drivers, as outlined in the TIFM_CORE Help.
- To compile this driver as a module, choose M here: the module will
+ To compile this driver as a module, choose M here: the module will
be called tifm_7xx1.
-config ACER_WMI
- tristate "Acer WMI Laptop Extras (EXPERIMENTAL)"
- depends on X86
- depends on EXPERIMENTAL
- depends on ACPI
- depends on LEDS_CLASS
- depends on BACKLIGHT_CLASS_DEVICE
- select ACPI_WMI
- ---help---
- This is a driver for newer Acer (and Wistron) laptops. It adds
- wireless radio and bluetooth control, and on some laptops,
- exposes the mail LED and LCD backlight.
-
- For more information about this driver see
- <file:Documentation/laptops/acer-wmi.txt>
-
- If you have an ACPI-WMI compatible Acer/ Wistron laptop, say Y or M
- here.
-
-config ASUS_LAPTOP
- tristate "Asus Laptop Extras (EXPERIMENTAL)"
- depends on X86
- depends on ACPI
- depends on EXPERIMENTAL && !ACPI_ASUS
- depends on LEDS_CLASS
- depends on BACKLIGHT_CLASS_DEVICE
- ---help---
- This is the new Linux driver for Asus laptops. It may also support some
- MEDION, JVC or VICTOR laptops. It makes all the extra buttons generate
- standard ACPI events that go through /proc/acpi/events. It also adds
- support for video output switching, LCD backlight control, Bluetooth and
- Wlan control, and most importantly, allows you to blink those fancy LEDs.
-
- For more information and a userspace daemon for handling the extra
- buttons see <http://acpi4asus.sf.net/>.
-
- If you have an ACPI-compatible ASUS laptop, say Y or M here.
-
-config FUJITSU_LAPTOP
- tristate "Fujitsu Laptop Extras"
- depends on X86
- depends on ACPI
- depends on BACKLIGHT_CLASS_DEVICE
- ---help---
- This is a driver for laptops built by Fujitsu:
-
- * P2xxx/P5xxx/S6xxx/S7xxx series Lifebooks
- * Possibly other Fujitsu laptop models
-
- It adds support for LCD brightness control.
-
- If you have a Fujitsu laptop, say Y or M here.
-
-config TC1100_WMI
- tristate "HP Compaq TC1100 Tablet WMI Extras (EXPERIMENTAL)"
- depends on X86 && !X86_64
- depends on EXPERIMENTAL
- depends on ACPI
- select ACPI_WMI
- ---help---
- This is a driver for the WMI extensions (wireless and bluetooth power
- control) of the HP Compaq TC1100 tablet.
-
-config MSI_LAPTOP
- tristate "MSI Laptop Extras"
- depends on X86
- depends on ACPI_EC
- depends on BACKLIGHT_CLASS_DEVICE
- ---help---
- This is a driver for laptops built by MSI (MICRO-STAR
- INTERNATIONAL):
-
- MSI MegaBook S270 (MS-1013)
- Cytron/TCM/Medion/Tchibo MD96100/SAM2000
-
- It adds support for Bluetooth, WLAN and LCD brightness control.
-
- More information about this driver is available at
- <http://0pointer.de/lennart/tchibo.html>.
-
- If you have an MSI S270 laptop, say Y or M here.
-
-config SONY_LAPTOP
- tristate "Sony Laptop Extras"
- depends on X86 && ACPI
- select BACKLIGHT_CLASS_DEVICE
- depends on INPUT
- ---help---
- This mini-driver drives the SNC and SPIC devices present in the ACPI
- BIOS of the Sony Vaio laptops.
-
- It gives access to some extra laptop functionalities like Bluetooth,
- screen brightness control, Fn keys and allows powering on/off some
- devices.
-
- Read <file:Documentation/laptops/sony-laptop.txt> for more information.
-
-config SONYPI_COMPAT
- bool "Sonypi compatibility"
- depends on SONY_LAPTOP
- ---help---
- Build the sonypi driver compatibility code into the sony-laptop driver.
-
-config THINKPAD_ACPI
- tristate "ThinkPad ACPI Laptop Extras"
- depends on X86 && ACPI
- select BACKLIGHT_CLASS_DEVICE
- select HWMON
- select NVRAM
- depends on INPUT
+config ICS932S401
+ tristate "Integrated Circuits ICS932S401"
+ depends on I2C && EXPERIMENTAL
+ help
+ If you say yes here you get support for the Integrated Circuits
+ ICS932S401 clock control chips.
+
+ This driver can also be built as a module. If so, the module
+ will be called ics932s401.
+
+config ATMEL_SSC
+ tristate "Device driver for Atmel SSC peripheral"
+ depends on AVR32 || ARCH_AT91
---help---
- This is a driver for the IBM and Lenovo ThinkPad laptops. It adds
- support for Fn-Fx key combinations, Bluetooth control, video
- output switching, ThinkLight control, UltraBay eject and more.
- For more information about this driver see
- <file:Documentation/laptops/thinkpad-acpi.txt> and
- <http://ibm-acpi.sf.net/> .
+ This option enables device driver support for Atmel Synchronized
+ Serial Communication peripheral (SSC).
- This driver was formerly known as ibm-acpi.
+ The SSC peripheral supports a wide variety of serial frame based
+ communications, i.e. I2S, SPI, etc.
- If you have an IBM or Lenovo ThinkPad laptop, say Y or M here.
+ If unsure, say N.
-config THINKPAD_ACPI_DEBUG
- bool "Verbose debug mode"
- depends on THINKPAD_ACPI
+config ENCLOSURE_SERVICES
+ tristate "Enclosure Services"
default n
- ---help---
- Enables extra debugging information, at the expense of a slightly
- increase in driver size.
+ help
+ Provides support for intelligent enclosures (bays which
+ contain storage devices). You also need either a host
+ driver (SCSI/ATA) which supports enclosures
+ or a SCSI enclosure device (SES) to use these services.
- If you are not sure, say N here.
+config SGI_XP
+ tristate "Support communication between SGI SSIs"
+ depends on NET
+ depends on (IA64_GENERIC || IA64_SGI_SN2 || IA64_SGI_UV || X86_UV) && SMP
+ select IA64_UNCACHED_ALLOCATOR if IA64_GENERIC || IA64_SGI_SN2
+ select GENERIC_ALLOCATOR if IA64_GENERIC || IA64_SGI_SN2
+ select SGI_GRU if X86_64 && SMP
+ ---help---
+ An SGI machine can be divided into multiple Single System
+ Images which act independently of each other and have
+ hardware based memory protection from the others. Enabling
+ this feature will allow for direct communication between SSIs
+ based on a network adapter and DMA messaging.
+
+config CS5535_MFGPT
+ tristate "CS5535/CS5536 Geode Multi-Function General Purpose Timer (MFGPT) support"
+ depends on PCI
+ depends on X86
+ default n
+ help
+ This driver provides access to MFGPT functionality for other
+ drivers that need timers. MFGPTs are available in the CS5535 and
+ CS5536 companion chips that are found in AMD Geode and several
+ other platforms. They have a better resolution and max interval
+ than the generic PIT, and are suitable for use as high-res timers.
+ You probably don't want to enable this manually; other drivers that
+ make use of it should enable it.
+
+config CS5535_MFGPT_DEFAULT_IRQ
+ int
+ depends on CS5535_MFGPT
+ default 7
+ help
+ MFGPTs on the CS5535 require an interrupt. The selected IRQ
+ can be overridden as a module option as well as by driver that
+ use the cs5535_mfgpt_ API; however, different architectures might
+ want to use a different IRQ by default. This is here for
+ architectures to set as necessary.
+
+config CS5535_CLOCK_EVENT_SRC
+ tristate "CS5535/CS5536 high-res timer (MFGPT) events"
+ depends on GENERIC_TIME && GENERIC_CLOCKEVENTS && CS5535_MFGPT
+ help
+ This driver provides a clock event source based on the MFGPT
+ timer(s) in the CS5535 and CS5536 companion chips.
+ MFGPTs have a better resolution and max interval than the
+ generic PIT, and are suitable for use as high-res timers.
-config THINKPAD_ACPI_DOCK
- bool "Legacy Docking Station Support"
- depends on THINKPAD_ACPI
- depends on ACPI_DOCK=n
+config HP_ILO
+ tristate "Channel interface driver for HP iLO/iLO2 processor"
+ depends on PCI
+ default n
+ help
+ The channel interface driver allows applications to communicate
+ with iLO/iLO2 management processors present on HP ProLiant
+ servers. Upon loading, the driver creates /dev/hpilo/dXccbN files,
+ which can be used to gather data from the management processor,
+ via read and write system calls.
+
+ To compile this driver as a module, choose M here: the
+ module will be called hpilo.
+
+config SGI_GRU
+ tristate "SGI GRU driver"
+ depends on X86_UV && SMP
+ default n
+ select MMU_NOTIFIER
+ ---help---
+ The GRU is a hardware resource located in the system chipset. The GRU
+ contains memory that can be mmapped into the user address space. This memory is
+ used to communicate with the GRU to perform functions such as load/store,
+ scatter/gather, bcopy, AMOs, etc. The GRU is directly accessed by user
+ instructions using user virtual addresses. GRU instructions (ex., bcopy) use
+ user virtual addresses for operands.
+
+ If you are not running on a SGI UV system, say N.
+
+config SGI_GRU_DEBUG
+ bool "SGI GRU driver debug"
+ depends on SGI_GRU
default n
---help---
- Allows the thinkpad_acpi driver to handle docking station events.
- This support was made obsolete by the generic ACPI docking station
- support (CONFIG_ACPI_DOCK). It will allow locking and removing the
- laptop from the docking station, but will not properly connect PCI
- devices.
+ This option enables addition debugging code for the SGI GRU driver. If
+ you are unsure, say N.
- If you are not sure, say N here.
+config ISL29003
+ tristate "Intersil ISL29003 ambient light sensor"
+ depends on I2C && SYSFS
+ help
+ If you say yes here you get support for the Intersil ISL29003
+ ambient light sensor.
-config THINKPAD_ACPI_BAY
- bool "Legacy Removable Bay Support"
- depends on THINKPAD_ACPI
- default y
- ---help---
- Allows the thinkpad_acpi driver to handle removable bays. It will
- electrically disable the device in the bay, and also generate
- notifications when the bay lever is ejected or inserted.
+ This driver can also be built as a module. If so, the module
+ will be called isl29003.
- If you are not sure, say Y here.
+config SENSORS_TSL2550
+ tristate "Taos TSL2550 ambient light sensor"
+ depends on I2C && SYSFS
+ help
+ If you say yes here you get support for the Taos TSL2550
+ ambient light sensor.
-config THINKPAD_ACPI_HOTKEY_POLL
- bool "Suport NVRAM polling for hot keys"
- depends on THINKPAD_ACPI
- default y
- ---help---
- Some thinkpad models benefit from NVRAM polling to detect a few of
- the hot key press events. If you know your ThinkPad model does not
- need to do NVRAM polling to support any of the hot keys you use,
- unselecting this option will save about 1kB of memory.
+ This driver can also be built as a module. If so, the module
+ will be called tsl2550.
- ThinkPads T40 and newer, R52 and newer, and X31 and newer are
- unlikely to need NVRAM polling in their latest BIOS versions.
+config EP93XX_PWM
+ tristate "EP93xx PWM support"
+ depends on ARCH_EP93XX
+ help
+ This option enables device driver support for the PWM channels
+ on the Cirrus EP93xx processors. The EP9307 chip only has one
+ PWM channel all the others have two, the second channel is an
+ alternate function of the EGPIO14 pin. A sysfs interface is
+ provided to control the PWM channels.
- NVRAM polling can detect at most the following keys: ThinkPad/Access
- IBM, Zoom, Switch Display (fn+F7), ThinkLight, Volume up/down/mute,
- Brightness up/down, Display Expand (fn+F8), Hibernate (fn+F12).
+ To compile this driver as a module, choose M here: the module will
+ be called ep93xx_pwm.
- If you are not sure, say Y here. The driver enables polling only if
- it is strictly necessary to do so.
+config DS1682
+ tristate "Dallas DS1682 Total Elapsed Time Recorder with Alarm"
+ depends on I2C && EXPERIMENTAL
+ help
+ If you say yes here you get support for Dallas Semiconductor
+ DS1682 Total Elapsed Time Recorder.
-config ATMEL_SSC
- tristate "Device driver for Atmel SSC peripheral"
- depends on AVR32 || ARCH_AT91
- ---help---
- This option enables device driver support for Atmel Syncronized
- Serial Communication peripheral (SSC).
+ This driver can also be built as a module. If so, the module
+ will be called ds1682.
- The SSC peripheral supports a wide variety of serial frame based
- communications, i.e. I2S, SPI, etc.
+config TI_DAC7512
+ tristate "Texas Instruments DAC7512"
+ depends on SPI && SYSFS
+ help
+ If you say yes here you get support for the Texas Instruments
+ DAC7512 16-bit digital-to-analog converter.
- If unsure, say N.
+ This driver can also be built as a module. If so, the module
+ will be calles ti_dac7512.
-config INTEL_MENLOW
- tristate "Thermal Management driver for Intel menlow platform"
- depends on ACPI_THERMAL
+config VMWARE_BALLOON
+ tristate "VMware Balloon Driver"
depends on X86
- ---help---
- ACPI thermal management enhancement driver on
- Intel Menlow platform.
+ help
+ This is VMware physical memory management driver which acts
+ like a "balloon" that can be inflated to reclaim physical pages
+ by reserving them in the guest and invalidating them in the
+ monitor, freeing up the underlying machine pages so they can
+ be allocated to other guests. The balloon can also be deflated
+ to allow the guest to use more physical memory.
If unsure, say N.
-config ENCLOSURE_SERVICES
- tristate "Enclosure Services"
- default n
- help
- Provides support for intelligent enclosures (bays which
- contain storage devices). You also need either a host
- driver (SCSI/ATA) which supports enclosures
- or a SCSI enclosure device (SES) to use these services.
+ To compile this driver as a module, choose M here: the
+ module will be called vmware_balloon.
+
+source "drivers/misc/c2port/Kconfig"
+source "drivers/misc/eeprom/Kconfig"
+source "drivers/misc/cb710/Kconfig"
+source "drivers/misc/iwmc3200top/Kconfig"
endif # MISC_DEVICES
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff