tristate
default n
+config MFD_88PM860X
+ bool "Support Marvell 88PM8606/88PM8607"
+ depends on I2C=y
+ select MFD_CORE
+ help
+ This supports for Marvell 88PM8606/88PM8607 Power Management IC.
+ This includes the I2C driver and the core APIs _only_, you have to
+ select individual components like voltage regulators, RTC and
+ battery-charger under the corresponding menus.
+
config MFD_SM501
tristate "Support for Silicon Motion SM501"
---help---
config MFD_SH_MOBILE_SDHI
bool "Support for SuperH Mobile SDHI"
- depends on SUPERH
+ depends on SUPERH || ARCH_SHMOBILE
select MFD_CORE
---help---
This driver supports the SDHI hardware block found in many
HTC Magician devices, respectively. Actual functionality is
handled by the leds-pasic3 and ds1wm drivers.
+config HTC_I2CPLD
+ bool "HTC I2C PLD chip support"
+ depends on I2C=y && GPIOLIB
+ help
+ If you say yes here you get support for the supposed CPLD
+ found on omap850 HTC devices like the HTC Wizard and HTC Herald.
+ This device provides input and output GPIOs through an I2C
+ interface to one or more sub-chips.
+
config UCB1400_CORE
tristate "Philips UCB1400 Core driver"
depends on AC97_BUS
config MENELAUS
bool "Texas Instruments TWL92330/Menelaus PM chip"
- depends on I2C=y && ARCH_OMAP24XX
+ depends on I2C=y && ARCH_OMAP2
help
If you say yes here you get support for the Texas Instruments
TWL92330/Menelaus Power Management chip. This include voltage
cell phones and PDAs.
config TWL4030_CORE
- bool "Texas Instruments TWL4030/TPS659x0 Support"
+ bool "Texas Instruments TWL4030/TWL5030/TWL6030/TPS659x0 Support"
depends on I2C=y && GENERIC_HARDIRQS
help
- Say yes here if you have TWL4030 family chip on your board.
+ Say yes here if you have TWL4030 / TWL6030 family chip on your board.
This core driver provides register access and IRQ handling
facilities, and registers devices for the various functions
so that function-specific drivers can bind to them.
individual components like LCD backlight, voltage regulators,
LEDs and battery-charger under the corresponding menus.
+config PMIC_ADP5520
+ bool "Analog Devices ADP5520/01 MFD PMIC Core Support"
+ depends on I2C=y
+ help
+ Say yes here to add support for Analog Devices AD5520 and ADP5501,
+ Multifunction Power Management IC. This includes
+ the I2C driver and the core APIs _only_, you have to select
+ individual components like LCD backlight, LEDs, GPIOs and Kepad
+ under the corresponding menus.
+
+config MFD_MAX8925
+ bool "Maxim Semiconductor MAX8925 PMIC Support"
+ depends on I2C=y
+ select MFD_CORE
+ help
+ Say yes here to support for Maxim Semiconductor MAX8925. This is
+ a Power Management IC. This driver provies common support for
+ accessing the device, additional drivers must be enabled in order
+ to use the functionality of the device.
+
config MFD_WM8400
tristate "Support Wolfson Microelectronics WM8400"
select MFD_CORE
the functionality of the device.
config MFD_WM831X
- tristate "Support Wolfson Microelectronics WM831x/2x PMICs"
+ bool "Support Wolfson Microelectronics WM831x/2x PMICs"
select MFD_CORE
- depends on I2C
+ depends on I2C=y
help
Support for the Wolfson Microelecronics WM831x and WM832x PMICs.
This driver provides common support for accessing the device,
functionality of the device.
config MFD_WM8350
- tristate
+ bool
config MFD_WM8350_CONFIG_MODE_0
bool
depends on MFD_WM8350
config MFD_WM8350_I2C
- tristate "Support Wolfson Microelectronics WM8350 with I2C"
+ bool "Support Wolfson Microelectronics WM8350 with I2C"
select MFD_WM8350
- depends on I2C
+ depends on I2C=y
help
The WM8350 is an integrated audio and power management
subsystem with watchdog and RTC functionality for embedded
I2C as the control interface. Additional options must be
selected to enable support for the functionality of the chip.
+config MFD_WM8994
+ tristate "Support Wolfson Microelectronics WM8994"
+ select MFD_CORE
+ depends on I2C
+ help
+ The WM8994 is a highly integrated hi-fi CODEC designed for
+ smartphone applicatiosn. As well as audio functionality it
+ has on board GPIO and regulator functionality which is
+ supported via the relevant subsystems. This driver provides
+ core support for the WM8994, in order to use the actual
+ functionaltiy of the device other drivers must be enabled.
+
config MFD_PCF50633
tristate "Support for NXP PCF50633"
depends on I2C
the PCF50633 chip.
config AB3100_CORE
- tristate "ST-Ericsson AB3100 Mixed Signal Circuit core functions"
- depends on I2C
+ bool "ST-Ericsson AB3100 Mixed Signal Circuit core functions"
+ depends on I2C=y
default y if ARCH_U300
help
Select this to enable the AB3100 Mixed Signal IC core
This enables the PCAP ASIC present on EZX Phones. This is
needed for MMC, TouchScreen, Sound, USB, etc..
-config MFD_88PM8607
- bool "Support Marvell 88PM8607"
- depends on I2C=y
- select MFD_CORE
- help
- This supports for Marvell 88PM8607 Power Management IC. This includes
- the I2C driver and the core APIs _only_, you have to select
- individual components like voltage regulators, RTC and
- battery-charger under the corresponding menus.
-
config AB4500_CORE
tristate "ST-Ericsson's AB4500 Mixed Signal Power management chip"
depends on SPI
- default y
help
Select this option to enable access to AB4500 power management
chip. This connects to U8500 on the SSP/SPI bus and exports
read/write functions for the devices to get access to this chip.
This chip embeds various other multimedia funtionalities as well.
+config MFD_TIMBERDALE
+ tristate "Support for the Timberdale FPGA"
+ select MFD_CORE
+ depends on PCI && GPIOLIB
+ ---help---
+ This is the core driver for the timberdale FPGA. This device is a
+ multifunction device which exposes numerous platform devices.
+
+ The timberdale FPGA can be found on the Intel Atom development board
+ for in-vehicle infontainment, called Russellville.
+
+config LPC_SCH
+ tristate "Intel SCH LPC"
+ depends on PCI
+ select MFD_CORE
+ help
+ LPC bridge function of the Intel SCH provides support for
+ System Management Bus and General Purpose I/O.
+
endmenu
menu "Multimedia Capabilities Port drivers"
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff