*/
#include <linux/module.h>
-#include <linux/moduleparam.h>
#include <linux/init.h>
#include <linux/delay.h>
#include <linux/interrupt.h>
#include <linux/input.h>
+#include <linux/slab.h>
#include "saa7134-reg.h"
#include "saa7134.h"
-static unsigned int disable_ir = 0;
+#define MODULE_NAME "saa7134"
+
+static unsigned int disable_ir;
module_param(disable_ir, int, 0444);
MODULE_PARM_DESC(disable_ir,"disable infrared remote support");
-static unsigned int ir_debug = 0;
+static unsigned int ir_debug;
module_param(ir_debug, int, 0644);
MODULE_PARM_DESC(ir_debug,"enable debug messages [IR]");
-static int pinnacle_remote = 0;
+static int pinnacle_remote;
module_param(pinnacle_remote, int, 0644); /* Choose Pinnacle PCTV remote */
MODULE_PARM_DESC(pinnacle_remote, "Specify Pinnacle PCTV remote: 0=coloured, 1=grey (defaults to 0)");
static int ir_rc5_key_timeout = 115;
module_param(ir_rc5_key_timeout, int, 0644);
+static int repeat_delay = 500;
+module_param(repeat_delay, int, 0644);
+MODULE_PARM_DESC(repeat_delay, "delay before key repeat started");
+static int repeat_period = 33;
+module_param(repeat_period, int, 0644);
+MODULE_PARM_DESC(repeat_period, "repeat period between "
+ "keypresses when key is down");
+
+static unsigned int disable_other_ir;
+module_param(disable_other_ir, int, 0644);
+MODULE_PARM_DESC(disable_other_ir, "disable full codes of "
+ "alternative remotes from other manufacturers");
+
#define dprintk(fmt, arg...) if (ir_debug) \
printk(KERN_DEBUG "%s/ir: " fmt, dev->name , ## arg)
#define i2cdprintk(fmt, arg...) if (ir_debug) \
- printk(KERN_DEBUG "%s/ir: " fmt, ir->c.name , ## arg)
+ printk(KERN_DEBUG "%s/ir: " fmt, ir->name , ## arg)
-/** rc5 functions */
+/* Helper functions for RC5 and NEC decoding at GPIO16 or GPIO18 */
static int saa7134_rc5_irq(struct saa7134_dev *dev);
+static int saa7134_nec_irq(struct saa7134_dev *dev);
+static int saa7134_raw_decode_irq(struct saa7134_dev *dev);
+static void nec_task(unsigned long data);
+static void saa7134_nec_timer(unsigned long data);
/* -------------------- GPIO generic keycode builder -------------------- */
struct card_ir *ir = dev->remote;
u32 gpio, data;
+ /* here comes the additional handshake steps for some cards */
+ switch (dev->board) {
+ case SAA7134_BOARD_GOTVIEW_7135:
+ saa_setb(SAA7134_GPIO_GPSTATUS1, 0x80);
+ saa_clearb(SAA7134_GPIO_GPSTATUS1, 0x80);
+ break;
+ }
/* rising SAA7134_GPIO_GPRESCAN reads the status */
saa_clearb(SAA7134_GPIO_GPMODE3,SAA7134_GPIO_GPRESCAN);
saa_setb(SAA7134_GPIO_GPMODE3,SAA7134_GPIO_GPRESCAN);
dprintk("build_key gpio=0x%x mask=0x%x data=%d\n",
gpio, ir->mask_keycode, data);
+ switch (dev->board) {
+ case SAA7134_BOARD_KWORLD_PLUS_TV_ANALOG:
+ if (data == ir->mask_keycode)
+ ir_input_nokey(ir->dev, &ir->ir);
+ else
+ ir_input_keydown(ir->dev, &ir->ir, data);
+ return 0;
+ }
+
if (ir->polling) {
if ((ir->mask_keydown && (0 != (gpio & ir->mask_keydown))) ||
(ir->mask_keyup && (0 == (gpio & ir->mask_keyup)))) {
- ir_input_keydown(ir->dev, &ir->ir, data, data);
+ ir_input_keydown(ir->dev, &ir->ir, data);
} else {
ir_input_nokey(ir->dev, &ir->ir);
}
else { /* IRQ driven mode - handle key press and release in one go */
if ((ir->mask_keydown && (0 != (gpio & ir->mask_keydown))) ||
(ir->mask_keyup && (0 == (gpio & ir->mask_keyup)))) {
- ir_input_keydown(ir->dev, &ir->ir, data, data);
+ ir_input_keydown(ir->dev, &ir->ir, data);
ir_input_nokey(ir->dev, &ir->ir);
}
}
/* --------------------- Chip specific I2C key builders ----------------- */
+static int get_key_flydvb_trio(struct IR_i2c *ir, u32 *ir_key, u32 *ir_raw)
+{
+ int gpio;
+ int attempt = 0;
+ unsigned char b;
+
+ /* We need this to access GPI Used by the saa_readl macro. */
+ struct saa7134_dev *dev = ir->c->adapter->algo_data;
+
+ if (dev == NULL) {
+ dprintk("get_key_flydvb_trio: "
+ "gir->c->adapter->algo_data is NULL!\n");
+ return -EIO;
+ }
+
+ /* rising SAA7134_GPIGPRESCAN reads the status */
+ saa_clearb(SAA7134_GPIO_GPMODE3, SAA7134_GPIO_GPRESCAN);
+ saa_setb(SAA7134_GPIO_GPMODE3, SAA7134_GPIO_GPRESCAN);
+
+ gpio = saa_readl(SAA7134_GPIO_GPSTATUS0 >> 2);
+
+ if (0x40000 & ~gpio)
+ return 0; /* No button press */
+
+ /* No button press - only before first key pressed */
+ if (b == 0xFF)
+ return 0;
+
+ /* poll IR chip */
+ /* weak up the IR chip */
+ b = 0;
+
+ while (1 != i2c_master_send(ir->c, &b, 1)) {
+ if ((attempt++) < 10) {
+ /*
+ * wait a bit for next attempt -
+ * I don't know how make it better
+ */
+ msleep(10);
+ continue;
+ }
+ i2cdprintk("send wake up byte to pic16C505 (IR chip)"
+ "failed %dx\n", attempt);
+ return -EIO;
+ }
+ if (1 != i2c_master_recv(ir->c, &b, 1)) {
+ i2cdprintk("read error\n");
+ return -EIO;
+ }
+
+ *ir_key = b;
+ *ir_raw = b;
+ return 1;
+}
+
+static int get_key_msi_tvanywhere_plus(struct IR_i2c *ir, u32 *ir_key,
+ u32 *ir_raw)
+{
+ unsigned char b;
+ int gpio;
+
+ /* <dev> is needed to access GPIO. Used by the saa_readl macro. */
+ struct saa7134_dev *dev = ir->c->adapter->algo_data;
+ if (dev == NULL) {
+ dprintk("get_key_msi_tvanywhere_plus: "
+ "gir->c->adapter->algo_data is NULL!\n");
+ return -EIO;
+ }
+
+ /* rising SAA7134_GPIO_GPRESCAN reads the status */
+
+ saa_clearb(SAA7134_GPIO_GPMODE3, SAA7134_GPIO_GPRESCAN);
+ saa_setb(SAA7134_GPIO_GPMODE3, SAA7134_GPIO_GPRESCAN);
+
+ gpio = saa_readl(SAA7134_GPIO_GPSTATUS0 >> 2);
+
+ /* GPIO&0x40 is pulsed low when a button is pressed. Don't do
+ I2C receive if gpio&0x40 is not low. */
+
+ if (gpio & 0x40)
+ return 0; /* No button press */
+
+ /* GPIO says there is a button press. Get it. */
+
+ if (1 != i2c_master_recv(ir->c, &b, 1)) {
+ i2cdprintk("read error\n");
+ return -EIO;
+ }
+
+ /* No button press */
+
+ if (b == 0xff)
+ return 0;
+
+ /* Button pressed */
+
+ dprintk("get_key_msi_tvanywhere_plus: Key = 0x%02X\n", b);
+ *ir_key = b;
+ *ir_raw = b;
+ return 1;
+}
+
static int get_key_purpletv(struct IR_i2c *ir, u32 *ir_key, u32 *ir_raw)
{
unsigned char b;
/* poll IR chip */
- if (1 != i2c_master_recv(&ir->c,&b,1)) {
+ if (1 != i2c_master_recv(ir->c, &b, 1)) {
i2cdprintk("read error\n");
return -EIO;
}
unsigned char buf[5], cod4, code3, code4;
/* poll IR chip */
- if (5 != i2c_master_recv(&ir->c,buf,5))
+ if (5 != i2c_master_recv(ir->c, buf, 5))
return -EIO;
cod4 = buf[4];
return 1;
}
+
+static int get_key_beholdm6xx(struct IR_i2c *ir, u32 *ir_key, u32 *ir_raw)
+{
+ unsigned char data[12];
+ u32 gpio;
+
+ struct saa7134_dev *dev = ir->c->adapter->algo_data;
+
+ /* rising SAA7134_GPIO_GPRESCAN reads the status */
+ saa_clearb(SAA7134_GPIO_GPMODE3, SAA7134_GPIO_GPRESCAN);
+ saa_setb(SAA7134_GPIO_GPMODE3, SAA7134_GPIO_GPRESCAN);
+
+ gpio = saa_readl(SAA7134_GPIO_GPSTATUS0 >> 2);
+
+ if (0x400000 & ~gpio)
+ return 0; /* No button press */
+
+ ir->c->addr = 0x5a >> 1;
+
+ if (12 != i2c_master_recv(ir->c, data, 12)) {
+ i2cdprintk("read error\n");
+ return -EIO;
+ }
+ /* IR of this card normally decode signals NEC-standard from
+ * - Sven IHOO MT 5.1R remote. xxyye718
+ * - Sven DVD HD-10xx remote. xxyyf708
+ * - BBK ...
+ * - mayby others
+ * So, skip not our, if disable full codes mode.
+ */
+ if (data[10] != 0x6b && data[11] != 0x86 && disable_other_ir)
+ return 0;
+
+ /* Wrong data decode fix */
+ if (data[9] != (unsigned char)(~data[8]))
+ return 0;
+
+ *ir_key = data[9];
+ *ir_raw = data[9];
+
+ return 1;
+}
+
+/* Common (grey or coloured) pinnacle PCTV remote handling
+ *
+ */
+static int get_key_pinnacle(struct IR_i2c *ir, u32 *ir_key, u32 *ir_raw,
+ int parity_offset, int marker, int code_modulo)
+{
+ unsigned char b[4];
+ unsigned int start = 0,parity = 0,code = 0;
+
+ /* poll IR chip */
+ if (4 != i2c_master_recv(ir->c, b, 4)) {
+ i2cdprintk("read error\n");
+ return -EIO;
+ }
+
+ for (start = 0; start < ARRAY_SIZE(b); start++) {
+ if (b[start] == marker) {
+ code=b[(start+parity_offset + 1) % 4];
+ parity=b[(start+parity_offset) % 4];
+ }
+ }
+
+ /* Empty Request */
+ if (parity == 0)
+ return 0;
+
+ /* Repeating... */
+ if (ir->old == parity)
+ return 0;
+
+ ir->old = parity;
+
+ /* drop special codes when a key is held down a long time for the grey controller
+ In this case, the second bit of the code is asserted */
+ if (marker == 0xfe && (code & 0x40))
+ return 0;
+
+ code %= code_modulo;
+
+ *ir_raw = code;
+ *ir_key = code;
+
+ i2cdprintk("Pinnacle PCTV key %02x\n", code);
+
+ return 1;
+}
+
+/* The grey pinnacle PCTV remote
+ *
+ * There are one issue with this remote:
+ * - I2c packet does not change when the same key is pressed quickly. The workaround
+ * is to hold down each key for about half a second, so that another code is generated
+ * in the i2c packet, and the function can distinguish key presses.
+ *
+ * Sylvain Pasche <sylvain.pasche@gmail.com>
+ */
+static int get_key_pinnacle_grey(struct IR_i2c *ir, u32 *ir_key, u32 *ir_raw)
+{
+
+ return get_key_pinnacle(ir, ir_key, ir_raw, 1, 0xfe, 0xff);
+}
+
+
+/* The new pinnacle PCTV remote (with the colored buttons)
+ *
+ * Ricardo Cerqueira <v4l@cerqueira.org>
+ */
+static int get_key_pinnacle_color(struct IR_i2c *ir, u32 *ir_key, u32 *ir_raw)
+{
+ /* code_modulo parameter (0x88) is used to reduce code value to fit inside IR_KEYTAB_SIZE
+ *
+ * this is the only value that results in 42 unique
+ * codes < 128
+ */
+
+ return get_key_pinnacle(ir, ir_key, ir_raw, 2, 0x80, 0x88);
+}
+
void saa7134_input_irq(struct saa7134_dev *dev)
{
- struct card_ir *ir = dev->remote;
+ struct card_ir *ir;
+
+ if (!dev || !dev->remote)
+ return;
+
+ ir = dev->remote;
+ if (!ir->running)
+ return;
- if (!ir->polling && !ir->rc5_gpio) {
+ if (ir->nec_gpio) {
+ saa7134_nec_irq(dev);
+ } else if (!ir->polling && !ir->rc5_gpio && !ir->raw_decode) {
build_key(dev);
} else if (ir->rc5_gpio) {
saa7134_rc5_irq(dev);
+ } else if (ir->raw_decode) {
+ saa7134_raw_decode_irq(dev);
}
}
static void saa7134_input_timer(unsigned long data)
{
- struct saa7134_dev *dev = (struct saa7134_dev*)data;
+ struct saa7134_dev *dev = (struct saa7134_dev *)data;
struct card_ir *ir = dev->remote;
- unsigned long timeout;
build_key(dev);
- timeout = jiffies + (ir->polling * HZ / 1000);
- mod_timer(&ir->timer, timeout);
+ mod_timer(&ir->timer, jiffies + msecs_to_jiffies(ir->polling));
+}
+
+void ir_raw_decode_timer_end(unsigned long data)
+{
+ struct saa7134_dev *dev = (struct saa7134_dev *)data;
+ struct card_ir *ir = dev->remote;
+
+ ir_raw_event_handle(dev->remote->dev);
+
+ ir->active = 0;
}
-static void saa7134_ir_start(struct saa7134_dev *dev, struct card_ir *ir)
+static int __saa7134_ir_start(void *priv)
{
+ struct saa7134_dev *dev = priv;
+ struct card_ir *ir;
+
+ if (!dev)
+ return -EINVAL;
+
+ ir = dev->remote;
+ if (!ir)
+ return -EINVAL;
+
+ if (ir->running)
+ return 0;
+
+ ir->running = 1;
if (ir->polling) {
- init_timer(&ir->timer);
- ir->timer.function = saa7134_input_timer;
- ir->timer.data = (unsigned long)dev;
+ setup_timer(&ir->timer, saa7134_input_timer,
+ (unsigned long)dev);
ir->timer.expires = jiffies + HZ;
add_timer(&ir->timer);
} else if (ir->rc5_gpio) {
ir->addr = 0x17;
ir->rc5_key_timeout = ir_rc5_key_timeout;
ir->rc5_remote_gap = ir_rc5_remote_gap;
+ } else if (ir->nec_gpio) {
+ setup_timer(&ir->timer_keyup, saa7134_nec_timer,
+ (unsigned long)dev);
+ tasklet_init(&ir->tlet, nec_task, (unsigned long)dev);
+ } else if (ir->raw_decode) {
+ /* set timer_end for code completion */
+ init_timer(&ir->timer_end);
+ ir->timer_end.function = ir_raw_decode_timer_end;
+ ir->timer_end.data = (unsigned long)dev;
+ ir->active = 0;
}
+
+ return 0;
}
-static void saa7134_ir_stop(struct saa7134_dev *dev)
+static void __saa7134_ir_stop(void *priv)
{
+ struct saa7134_dev *dev = priv;
+ struct card_ir *ir;
+
+ if (!dev)
+ return;
+
+ ir = dev->remote;
+ if (!ir)
+ return;
+
+ if (!ir->running)
+ return;
if (dev->remote->polling)
del_timer_sync(&dev->remote->timer);
+ else if (ir->rc5_gpio)
+ del_timer_sync(&ir->timer_end);
+ else if (ir->nec_gpio)
+ tasklet_kill(&ir->tlet);
+ else if (ir->raw_decode) {
+ del_timer_sync(&ir->timer_end);
+ ir->active = 0;
+ }
+
+ ir->running = 0;
+
+ return;
+}
+
+int saa7134_ir_start(struct saa7134_dev *dev)
+{
+ if (dev->remote->users)
+ return __saa7134_ir_start(dev);
+
+ return 0;
+}
+
+void saa7134_ir_stop(struct saa7134_dev *dev)
+{
+ if (dev->remote->users)
+ __saa7134_ir_stop(dev);
+}
+
+static int saa7134_ir_open(void *priv)
+{
+ struct saa7134_dev *dev = priv;
+
+ dev->remote->users++;
+ return __saa7134_ir_start(dev);
+}
+
+static void saa7134_ir_close(void *priv)
+{
+ struct saa7134_dev *dev = priv;
+
+ dev->remote->users--;
+ if (!dev->remote->users)
+ __saa7134_ir_stop(dev);
+}
+
+
+int saa7134_ir_change_protocol(void *priv, u64 ir_type)
+{
+ struct saa7134_dev *dev = priv;
+ struct card_ir *ir = dev->remote;
+ u32 nec_gpio, rc5_gpio;
+
+ if (ir_type == IR_TYPE_RC5) {
+ dprintk("Changing protocol to RC5\n");
+ nec_gpio = 0;
+ rc5_gpio = 1;
+ } else if (ir_type == IR_TYPE_NEC) {
+ dprintk("Changing protocol to NEC\n");
+ nec_gpio = 1;
+ rc5_gpio = 0;
+ } else {
+ dprintk("IR protocol type %ud is not supported\n",
+ (unsigned)ir_type);
+ return -EINVAL;
+ }
+
+ if (ir->running) {
+ saa7134_ir_stop(dev);
+ ir->nec_gpio = nec_gpio;
+ ir->rc5_gpio = rc5_gpio;
+ saa7134_ir_start(dev);
+ } else {
+ ir->nec_gpio = nec_gpio;
+ ir->rc5_gpio = rc5_gpio;
+ }
+
+ return 0;
}
int saa7134_input_init1(struct saa7134_dev *dev)
{
struct card_ir *ir;
struct input_dev *input_dev;
- IR_KEYTAB_TYPE *ir_codes = NULL;
+ char *ir_codes = NULL;
u32 mask_keycode = 0;
u32 mask_keydown = 0;
u32 mask_keyup = 0;
int polling = 0;
int rc5_gpio = 0;
- int ir_type = IR_TYPE_OTHER;
+ int nec_gpio = 0;
+ int raw_decode = 0;
+ int allow_protocol_change = 0;
+ u64 ir_type = IR_TYPE_OTHER;
int err;
if (dev->has_remote != SAA7134_REMOTE_GPIO)
case SAA7134_BOARD_FLYVIDEO3000:
case SAA7134_BOARD_FLYTVPLATINUM_FM:
case SAA7134_BOARD_FLYTVPLATINUM_MINI2:
- ir_codes = ir_codes_flyvideo;
+ case SAA7134_BOARD_ROVERMEDIA_LINK_PRO_FM:
+ ir_codes = RC_MAP_FLYVIDEO;
mask_keycode = 0xEC00000;
mask_keydown = 0x0040000;
break;
case SAA7134_BOARD_CINERGY400:
case SAA7134_BOARD_CINERGY600:
case SAA7134_BOARD_CINERGY600_MK3:
- ir_codes = ir_codes_cinergy;
+ ir_codes = RC_MAP_CINERGY;
mask_keycode = 0x00003f;
mask_keyup = 0x040000;
break;
case SAA7134_BOARD_ECS_TVP3XP:
case SAA7134_BOARD_ECS_TVP3XP_4CB5:
- ir_codes = ir_codes_eztv;
+ ir_codes = RC_MAP_EZTV;
mask_keycode = 0x00017c;
mask_keyup = 0x000002;
polling = 50; // ms
break;
case SAA7134_BOARD_KWORLD_XPERT:
case SAA7134_BOARD_AVACSSMARTTV:
- ir_codes = ir_codes_pixelview;
+ ir_codes = RC_MAP_PIXELVIEW;
mask_keycode = 0x00001F;
mask_keyup = 0x000020;
polling = 50; // ms
case SAA7134_BOARD_AVERMEDIA_305:
case SAA7134_BOARD_AVERMEDIA_307:
case SAA7134_BOARD_AVERMEDIA_STUDIO_305:
+ case SAA7134_BOARD_AVERMEDIA_STUDIO_505:
case SAA7134_BOARD_AVERMEDIA_STUDIO_307:
case SAA7134_BOARD_AVERMEDIA_STUDIO_507:
+ case SAA7134_BOARD_AVERMEDIA_STUDIO_507UA:
case SAA7134_BOARD_AVERMEDIA_GO_007_FM:
- ir_codes = ir_codes_avermedia;
+ case SAA7134_BOARD_AVERMEDIA_M102:
+ case SAA7134_BOARD_AVERMEDIA_GO_007_FM_PLUS:
+ ir_codes = RC_MAP_AVERMEDIA;
mask_keycode = 0x0007C8;
mask_keydown = 0x000010;
polling = 50; // ms
saa_setb(SAA7134_GPIO_GPMODE0, 0x4);
saa_setb(SAA7134_GPIO_GPSTATUS0, 0x4);
break;
+ case SAA7134_BOARD_AVERMEDIA_M135A:
+ ir_codes = RC_MAP_AVERMEDIA_M135A_RM_JX;
+ mask_keydown = 0x0040000; /* Enable GPIO18 line on both edges */
+ mask_keyup = 0x0040000;
+ mask_keycode = 0xffff;
+ raw_decode = 1;
+ break;
+ case SAA7134_BOARD_AVERMEDIA_M733A:
+ ir_codes = RC_MAP_AVERMEDIA_M733A_RM_K6;
+ mask_keydown = 0x0040000;
+ mask_keyup = 0x0040000;
+ mask_keycode = 0xffff;
+ raw_decode = 1;
+ break;
case SAA7134_BOARD_AVERMEDIA_777:
case SAA7134_BOARD_AVERMEDIA_A16AR:
- ir_codes = ir_codes_avermedia;
+ ir_codes = RC_MAP_AVERMEDIA;
mask_keycode = 0x02F200;
mask_keydown = 0x000400;
polling = 50; // ms
saa_setb(SAA7134_GPIO_GPMODE1, 0x1);
saa_setb(SAA7134_GPIO_GPSTATUS1, 0x1);
break;
+ case SAA7134_BOARD_AVERMEDIA_A16D:
+ ir_codes = RC_MAP_AVERMEDIA_A16D;
+ mask_keycode = 0x02F200;
+ mask_keydown = 0x000400;
+ polling = 50; /* ms */
+ /* Without this we won't receive key up events */
+ saa_setb(SAA7134_GPIO_GPMODE1, 0x1);
+ saa_setb(SAA7134_GPIO_GPSTATUS1, 0x1);
+ break;
case SAA7134_BOARD_KWORLD_TERMINATOR:
- ir_codes = ir_codes_pixelview;
+ ir_codes = RC_MAP_PIXELVIEW;
mask_keycode = 0x00001f;
mask_keyup = 0x000060;
polling = 50; // ms
break;
case SAA7134_BOARD_MANLI_MTV001:
case SAA7134_BOARD_MANLI_MTV002:
- case SAA7134_BOARD_BEHOLD_409FM:
- ir_codes = ir_codes_manli;
+ ir_codes = RC_MAP_MANLI;
mask_keycode = 0x001f00;
mask_keyup = 0x004000;
+ polling = 50; /* ms */
+ break;
+ case SAA7134_BOARD_BEHOLD_409FM:
+ case SAA7134_BOARD_BEHOLD_401:
+ case SAA7134_BOARD_BEHOLD_403:
+ case SAA7134_BOARD_BEHOLD_403FM:
+ case SAA7134_BOARD_BEHOLD_405:
+ case SAA7134_BOARD_BEHOLD_405FM:
+ case SAA7134_BOARD_BEHOLD_407:
+ case SAA7134_BOARD_BEHOLD_407FM:
+ case SAA7134_BOARD_BEHOLD_409:
+ case SAA7134_BOARD_BEHOLD_505FM:
+ case SAA7134_BOARD_BEHOLD_505RDS_MK5:
+ case SAA7134_BOARD_BEHOLD_505RDS_MK3:
+ case SAA7134_BOARD_BEHOLD_507_9FM:
+ case SAA7134_BOARD_BEHOLD_507RDS_MK3:
+ case SAA7134_BOARD_BEHOLD_507RDS_MK5:
+ ir_codes = RC_MAP_MANLI;
+ mask_keycode = 0x003f00;
+ mask_keyup = 0x004000;
+ polling = 50; /* ms */
+ break;
+ case SAA7134_BOARD_BEHOLD_COLUMBUS_TVFM:
+ ir_codes = RC_MAP_BEHOLD_COLUMBUS;
+ mask_keycode = 0x003f00;
+ mask_keyup = 0x004000;
polling = 50; // ms
break;
case SAA7134_BOARD_SEDNA_PC_TV_CARDBUS:
- ir_codes = ir_codes_pctv_sedna;
+ ir_codes = RC_MAP_PCTV_SEDNA;
mask_keycode = 0x001f00;
mask_keyup = 0x004000;
polling = 50; // ms
break;
case SAA7134_BOARD_GOTVIEW_7135:
- ir_codes = ir_codes_gotview7135;
- mask_keycode = 0x0003EC;
- mask_keyup = 0x008000;
+ ir_codes = RC_MAP_GOTVIEW7135;
+ mask_keycode = 0x0003CC;
mask_keydown = 0x000010;
- polling = 50; // ms
+ polling = 5; /* ms */
+ saa_setb(SAA7134_GPIO_GPMODE1, 0x80);
break;
case SAA7134_BOARD_VIDEOMATE_TV_PVR:
case SAA7134_BOARD_VIDEOMATE_GOLD_PLUS:
case SAA7134_BOARD_VIDEOMATE_TV_GOLD_PLUSII:
- ir_codes = ir_codes_videomate_tv_pvr;
+ ir_codes = RC_MAP_VIDEOMATE_TV_PVR;
mask_keycode = 0x00003F;
mask_keyup = 0x400000;
polling = 50; // ms
break;
case SAA7134_BOARD_PROTEUS_2309:
- ir_codes = ir_codes_proteus_2309;
+ ir_codes = RC_MAP_PROTEUS_2309;
mask_keycode = 0x00007F;
mask_keyup = 0x000080;
polling = 50; // ms
break;
case SAA7134_BOARD_VIDEOMATE_DVBT_300:
case SAA7134_BOARD_VIDEOMATE_DVBT_200:
- ir_codes = ir_codes_videomate_tv_pvr;
+ ir_codes = RC_MAP_VIDEOMATE_TV_PVR;
mask_keycode = 0x003F00;
mask_keyup = 0x040000;
break;
+ case SAA7134_BOARD_FLYDVBS_LR300:
case SAA7134_BOARD_FLYDVBT_LR301:
case SAA7134_BOARD_FLYDVBTDUO:
- ir_codes = ir_codes_flydvb;
+ ir_codes = RC_MAP_FLYDVB;
mask_keycode = 0x0001F00;
mask_keydown = 0x0040000;
break;
case SAA7134_BOARD_ASUSTeK_P7131_DUAL:
case SAA7134_BOARD_ASUSTeK_P7131_HYBRID_LNA:
- ir_codes = ir_codes_asus_pc39;
+ case SAA7134_BOARD_ASUSTeK_P7131_ANALOG:
+ ir_codes = RC_MAP_ASUS_PC39;
mask_keydown = 0x0040000;
rc5_gpio = 1;
break;
case SAA7134_BOARD_ENCORE_ENLTV:
case SAA7134_BOARD_ENCORE_ENLTV_FM:
- ir_codes = ir_codes_encore_enltv;
+ ir_codes = RC_MAP_ENCORE_ENLTV;
mask_keycode = 0x00007f;
mask_keyup = 0x040000;
polling = 50; // ms
break;
+ case SAA7134_BOARD_ENCORE_ENLTV_FM53:
+ ir_codes = RC_MAP_ENCORE_ENLTV_FM53;
+ mask_keydown = 0x0040000;
+ mask_keycode = 0x00007f;
+ nec_gpio = 1;
+ break;
case SAA7134_BOARD_10MOONSTVMASTER3:
- ir_codes = ir_codes_encore_enltv;
+ ir_codes = RC_MAP_ENCORE_ENLTV;
mask_keycode = 0x5f80000;
mask_keyup = 0x8000000;
polling = 50; //ms
break;
+ case SAA7134_BOARD_GENIUS_TVGO_A11MCE:
+ ir_codes = RC_MAP_GENIUS_TVGO_A11MCE;
+ mask_keycode = 0xff;
+ mask_keydown = 0xf00000;
+ polling = 50; /* ms */
+ break;
+ case SAA7134_BOARD_REAL_ANGEL_220:
+ ir_codes = RC_MAP_REAL_AUDIO_220_32_KEYS;
+ mask_keycode = 0x3f00;
+ mask_keyup = 0x4000;
+ polling = 50; /* ms */
+ break;
+ case SAA7134_BOARD_KWORLD_PLUS_TV_ANALOG:
+ ir_codes = RC_MAP_KWORLD_PLUS_TV_ANALOG;
+ mask_keycode = 0x7f;
+ polling = 40; /* ms */
+ break;
+ case SAA7134_BOARD_VIDEOMATE_S350:
+ ir_codes = RC_MAP_VIDEOMATE_S350;
+ mask_keycode = 0x003f00;
+ mask_keydown = 0x040000;
+ break;
+ case SAA7134_BOARD_LEADTEK_WINFAST_DTV1000S:
+ ir_codes = RC_MAP_WINFAST;
+ mask_keycode = 0x5f00;
+ mask_keyup = 0x020000;
+ polling = 50; /* ms */
+ break;
+ break;
}
if (NULL == ir_codes) {
printk("%s: Oops: IR config error [card=%d]\n",
}
ir->dev = input_dev;
+ dev->remote = ir;
+
+ ir->running = 0;
/* init hardware-specific stuff */
ir->mask_keycode = mask_keycode;
ir->mask_keyup = mask_keyup;
ir->polling = polling;
ir->rc5_gpio = rc5_gpio;
+ ir->nec_gpio = nec_gpio;
+ ir->raw_decode = raw_decode;
/* init input device */
snprintf(ir->name, sizeof(ir->name), "saa7134 IR (%s)",
snprintf(ir->phys, sizeof(ir->phys), "pci-%s/ir0",
pci_name(dev->pci));
- ir_input_init(input_dev, &ir->ir, ir_type, ir_codes);
+
+ ir->props.priv = dev;
+ ir->props.open = saa7134_ir_open;
+ ir->props.close = saa7134_ir_close;
+
+ if (raw_decode)
+ ir->props.driver_type = RC_DRIVER_IR_RAW;
+
+ if (!raw_decode && allow_protocol_change) {
+ ir->props.allowed_protos = IR_TYPE_RC5 | IR_TYPE_NEC;
+ ir->props.change_protocol = saa7134_ir_change_protocol;
+ }
+
+ err = ir_input_init(input_dev, &ir->ir, ir_type);
+ if (err < 0)
+ goto err_out_free;
+
input_dev->name = ir->name;
input_dev->phys = ir->phys;
input_dev->id.bustype = BUS_PCI;
input_dev->id.vendor = dev->pci->vendor;
input_dev->id.product = dev->pci->device;
}
- input_dev->cdev.dev = &dev->pci->dev;
-
- dev->remote = ir;
- saa7134_ir_start(dev, ir);
+ input_dev->dev.parent = &dev->pci->dev;
- err = input_register_device(ir->dev);
+ err = ir_input_register(ir->dev, ir_codes, &ir->props, MODULE_NAME);
if (err)
- goto err_out_stop;
+ goto err_out_free;
+
+ /* the remote isn't as bouncy as a keyboard */
+ ir->dev->rep[REP_DELAY] = repeat_delay;
+ ir->dev->rep[REP_PERIOD] = repeat_period;
return 0;
- err_out_stop:
- saa7134_ir_stop(dev);
+err_out_free:
dev->remote = NULL;
- err_out_free:
- input_free_device(input_dev);
kfree(ir);
return err;
}
return;
saa7134_ir_stop(dev);
- input_unregister_device(dev->remote->dev);
+ ir_input_unregister(dev->remote->dev);
kfree(dev->remote);
dev->remote = NULL;
}
-void saa7134_set_i2c_ir(struct saa7134_dev *dev, struct IR_i2c *ir)
+void saa7134_probe_i2c_ir(struct saa7134_dev *dev)
{
+ struct i2c_board_info info;
+
+ struct i2c_msg msg_msi = {
+ .addr = 0x50,
+ .flags = I2C_M_RD,
+ .len = 0,
+ .buf = NULL,
+ };
+
+ int rc;
+
if (disable_ir) {
- dprintk("Found supported i2c remote, but IR has been disabled\n");
- ir->get_key=NULL;
+ dprintk("IR has been disabled, not probing for i2c remote\n");
return;
}
+ memset(&info, 0, sizeof(struct i2c_board_info));
+ memset(&dev->init_data, 0, sizeof(dev->init_data));
+ strlcpy(info.type, "ir_video", I2C_NAME_SIZE);
+
switch (dev->board) {
case SAA7134_BOARD_PINNACLE_PCTV_110i:
case SAA7134_BOARD_PINNACLE_PCTV_310i:
- snprintf(ir->c.name, sizeof(ir->c.name), "Pinnacle PCTV");
+ dev->init_data.name = "Pinnacle PCTV";
if (pinnacle_remote == 0) {
- ir->get_key = get_key_pinnacle_color;
- ir->ir_codes = ir_codes_pinnacle_color;
+ dev->init_data.get_key = get_key_pinnacle_color;
+ dev->init_data.ir_codes = RC_MAP_PINNACLE_COLOR;
+ info.addr = 0x47;
} else {
- ir->get_key = get_key_pinnacle_grey;
- ir->ir_codes = ir_codes_pinnacle_grey;
+ dev->init_data.get_key = get_key_pinnacle_grey;
+ dev->init_data.ir_codes = RC_MAP_PINNACLE_GREY;
+ info.addr = 0x47;
}
break;
case SAA7134_BOARD_UPMOST_PURPLE_TV:
- snprintf(ir->c.name, sizeof(ir->c.name), "Purple TV");
- ir->get_key = get_key_purpletv;
- ir->ir_codes = ir_codes_purpletv;
+ dev->init_data.name = "Purple TV";
+ dev->init_data.get_key = get_key_purpletv;
+ dev->init_data.ir_codes = RC_MAP_PURPLETV;
+ info.addr = 0x7a;
+ break;
+ case SAA7134_BOARD_MSI_TVATANYWHERE_PLUS:
+ dev->init_data.name = "MSI TV@nywhere Plus";
+ dev->init_data.get_key = get_key_msi_tvanywhere_plus;
+ dev->init_data.ir_codes = RC_MAP_MSI_TVANYWHERE_PLUS;
+ info.addr = 0x30;
+ /* MSI TV@nywhere Plus controller doesn't seem to
+ respond to probes unless we read something from
+ an existing device. Weird...
+ REVISIT: might no longer be needed */
+ rc = i2c_transfer(&dev->i2c_adap, &msg_msi, 1);
+ dprintk(KERN_DEBUG "probe 0x%02x @ %s: %s\n",
+ msg_msi.addr, dev->i2c_adap.name,
+ (1 == rc) ? "yes" : "no");
break;
case SAA7134_BOARD_HAUPPAUGE_HVR1110:
- snprintf(ir->c.name, sizeof(ir->c.name), "HVR 1110");
- ir->get_key = get_key_hvr1110;
- ir->ir_codes = ir_codes_hauppauge_new;
+ dev->init_data.name = "HVR 1110";
+ dev->init_data.get_key = get_key_hvr1110;
+ dev->init_data.ir_codes = RC_MAP_HAUPPAUGE_NEW;
+ info.addr = 0x71;
break;
- default:
- dprintk("Shouldn't get here: Unknown board %x for I2C IR?\n",dev->board);
+ case SAA7134_BOARD_BEHOLD_607FM_MK3:
+ case SAA7134_BOARD_BEHOLD_607FM_MK5:
+ case SAA7134_BOARD_BEHOLD_609FM_MK3:
+ case SAA7134_BOARD_BEHOLD_609FM_MK5:
+ case SAA7134_BOARD_BEHOLD_607RDS_MK3:
+ case SAA7134_BOARD_BEHOLD_607RDS_MK5:
+ case SAA7134_BOARD_BEHOLD_609RDS_MK3:
+ case SAA7134_BOARD_BEHOLD_609RDS_MK5:
+ case SAA7134_BOARD_BEHOLD_M6:
+ case SAA7134_BOARD_BEHOLD_M63:
+ case SAA7134_BOARD_BEHOLD_M6_EXTRA:
+ case SAA7134_BOARD_BEHOLD_H6:
+ case SAA7134_BOARD_BEHOLD_X7:
+ case SAA7134_BOARD_BEHOLD_H7:
+ case SAA7134_BOARD_BEHOLD_A7:
+ dev->init_data.name = "BeholdTV";
+ dev->init_data.get_key = get_key_beholdm6xx;
+ dev->init_data.ir_codes = RC_MAP_BEHOLD;
+ dev->init_data.type = IR_TYPE_NEC;
+ info.addr = 0x2d;
break;
+ case SAA7134_BOARD_AVERMEDIA_CARDBUS_501:
+ case SAA7134_BOARD_AVERMEDIA_CARDBUS_506:
+ info.addr = 0x40;
+ break;
+ case SAA7134_BOARD_FLYDVB_TRIO:
+ dev->init_data.name = "FlyDVB Trio";
+ dev->init_data.get_key = get_key_flydvb_trio;
+ dev->init_data.ir_codes = RC_MAP_FLYDVB;
+ info.addr = 0x0b;
+ break;
+ default:
+ dprintk("No I2C IR support for board %x\n", dev->board);
+ return;
}
+ if (dev->init_data.name)
+ info.platform_data = &dev->init_data;
+ i2c_new_device(&dev->i2c_adap, &info);
+}
+
+static int saa7134_raw_decode_irq(struct saa7134_dev *dev)
+{
+ struct card_ir *ir = dev->remote;
+ unsigned long timeout;
+ int space;
+
+ /* Generate initial event */
+ saa_clearb(SAA7134_GPIO_GPMODE3, SAA7134_GPIO_GPRESCAN);
+ saa_setb(SAA7134_GPIO_GPMODE3, SAA7134_GPIO_GPRESCAN);
+ space = saa_readl(SAA7134_GPIO_GPSTATUS0 >> 2) & ir->mask_keydown;
+ ir_raw_event_store_edge(dev->remote->dev, space ? IR_SPACE : IR_PULSE);
+
+
+ /*
+ * Wait 15 ms from the start of the first IR event before processing
+ * the event. This time is enough for NEC protocol. May need adjustments
+ * to work with other protocols.
+ */
+ if (!ir->active) {
+ timeout = jiffies + jiffies_to_msecs(15);
+ mod_timer(&ir->timer_end, timeout);
+ ir->active = 1;
+ }
+
+ return 1;
}
static int saa7134_rc5_irq(struct saa7134_dev *dev)
return 1;
}
-/* ----------------------------------------------------------------------
- * Local variables:
- * c-basic-offset: 8
- * End:
+/* On NEC protocol, One has 2.25 ms, and zero has 1.125 ms
+ The first pulse (start) has 9 + 4.5 ms
*/
+
+static void saa7134_nec_timer(unsigned long data)
+{
+ struct saa7134_dev *dev = (struct saa7134_dev *) data;
+ struct card_ir *ir = dev->remote;
+
+ dprintk("Cancel key repeat\n");
+
+ ir_input_nokey(ir->dev, &ir->ir);
+}
+
+static void nec_task(unsigned long data)
+{
+ struct saa7134_dev *dev = (struct saa7134_dev *) data;
+ struct card_ir *ir;
+ struct timeval tv;
+ int count, pulse, oldpulse, gap;
+ u32 ircode = 0, not_code = 0;
+ int ngap = 0;
+
+ if (!data) {
+ printk(KERN_ERR "saa713x/ir: Can't recover dev struct\n");
+ /* GPIO will be kept disabled */
+ return;
+ }
+
+ ir = dev->remote;
+
+ /* rising SAA7134_GPIO_GPRESCAN reads the status */
+ saa_clearb(SAA7134_GPIO_GPMODE3, SAA7134_GPIO_GPRESCAN);
+ saa_setb(SAA7134_GPIO_GPMODE3, SAA7134_GPIO_GPRESCAN);
+
+ oldpulse = saa_readl(SAA7134_GPIO_GPSTATUS0 >> 2) & ir->mask_keydown;
+ pulse = oldpulse;
+
+ do_gettimeofday(&tv);
+ ir->base_time = tv;
+
+ /* Decode NEC pulsecode. This code can take up to 76.5 ms to run.
+ Unfortunately, using IRQ to decode pulse didn't work, since it uses
+ a pulse train of 38KHz. This means one pulse on each 52 us
+ */
+ do {
+ /* Wait until the end of pulse/space or 5 ms */
+ for (count = 0; count < 500; count++) {
+ udelay(10);
+ /* rising SAA7134_GPIO_GPRESCAN reads the status */
+ saa_clearb(SAA7134_GPIO_GPMODE3, SAA7134_GPIO_GPRESCAN);
+ saa_setb(SAA7134_GPIO_GPMODE3, SAA7134_GPIO_GPRESCAN);
+ pulse = saa_readl(SAA7134_GPIO_GPSTATUS0 >> 2)
+ & ir->mask_keydown;
+ if (pulse != oldpulse)
+ break;
+ }
+
+ do_gettimeofday(&tv);
+ gap = 1000000 * (tv.tv_sec - ir->base_time.tv_sec) +
+ tv.tv_usec - ir->base_time.tv_usec;
+
+ if (!pulse) {
+ /* Bit 0 has 560 us, while bit 1 has 1120 us.
+ Do something only if bit == 1
+ */
+ if (ngap && (gap > 560 + 280)) {
+ unsigned int shift = ngap - 1;
+
+ /* Address first, then command */
+ if (shift < 8) {
+ shift += 8;
+ ircode |= 1 << shift;
+ } else if (shift < 16) {
+ not_code |= 1 << shift;
+ } else if (shift < 24) {
+ shift -= 16;
+ ircode |= 1 << shift;
+ } else {
+ shift -= 24;
+ not_code |= 1 << shift;
+ }
+ }
+ ngap++;
+ }
+
+
+ ir->base_time = tv;
+
+ /* TIMEOUT - Long pulse */
+ if (gap >= 5000)
+ break;
+ oldpulse = pulse;
+ } while (ngap < 32);
+
+ if (ngap == 32) {
+ /* FIXME: should check if not_code == ~ircode */
+ ir->code = ir_extract_bits(ircode, ir->mask_keycode);
+
+ dprintk("scancode = 0x%02x (code = 0x%02x, notcode= 0x%02x)\n",
+ ir->code, ircode, not_code);
+
+ ir_input_keydown(ir->dev, &ir->ir, ir->code);
+ } else
+ dprintk("Repeat last key\n");
+
+ /* Keep repeating the last key */
+ mod_timer(&ir->timer_keyup, jiffies + msecs_to_jiffies(150));
+
+ saa_setl(SAA7134_IRQ2, SAA7134_IRQ2_INTE_GPIO18_P);
+}
+
+static int saa7134_nec_irq(struct saa7134_dev *dev)
+{
+ struct card_ir *ir = dev->remote;
+
+ saa_clearl(SAA7134_IRQ2, SAA7134_IRQ2_INTE_GPIO18_P);
+ tasklet_schedule(&ir->tlet);
+
+ return 1;
+}