/*
- * Copyright (c) 2006, 2007 QLogic Corporation. All rights reserved.
+ * Copyright (c) 2006, 2007, 2008 QLogic Corporation. All rights reserved.
* Copyright (c) 2003, 2004, 2005, 2006 PathScale, Inc. All rights reserved.
*
* This software is available to you under a choice of one of two
* SOFTWARE.
*/
+#include <linux/sched.h>
#include <linux/spinlock.h>
#include <linux/idr.h>
#include <linux/pci.h>
#include "ipath_kernel.h"
#include "ipath_verbs.h"
-#include "ipath_common.h"
static void ipath_update_pio_bufs(struct ipath_devdata *);
MODULE_PARM_DESC(debug, "mask for debug prints");
EXPORT_SYMBOL_GPL(ipath_debug);
+unsigned ipath_mtu4096 = 1; /* max 4KB IB mtu by default, if supported */
+module_param_named(mtu4096, ipath_mtu4096, uint, S_IRUGO);
+MODULE_PARM_DESC(mtu4096, "enable MTU of 4096 bytes, if supported");
+
+static unsigned ipath_hol_timeout_ms = 13000;
+module_param_named(hol_timeout_ms, ipath_hol_timeout_ms, uint, S_IRUGO);
+MODULE_PARM_DESC(hol_timeout_ms,
+ "duration of user app suspension after link failure");
+
+unsigned ipath_linkrecovery = 1;
+module_param_named(linkrecovery, ipath_linkrecovery, uint, S_IWUSR | S_IRUGO);
+MODULE_PARM_DESC(linkrecovery, "enable workaround for link recovery issue");
+
MODULE_LICENSE("GPL");
-MODULE_AUTHOR("QLogic <support@pathscale.com>");
+MODULE_AUTHOR("QLogic <support@qlogic.com>");
MODULE_DESCRIPTION("QLogic InfiniPath driver");
+/*
+ * Table to translate the LINKTRAININGSTATE portion of
+ * IBCStatus to a human-readable form.
+ */
const char *ipath_ibcstatus_str[] = {
"Disabled",
"LinkUp",
"CfgWaitRmt",
"CfgIdle",
"RecovRetrain",
- "LState0xD", /* unused */
+ "CfgTxRevLane", /* unused before IBA7220 */
"RecovWaitRmt",
"RecovIdle",
+ /* below were added for IBA7220 */
+ "CfgEnhanced",
+ "CfgTest",
+ "CfgWaitRmtTest",
+ "CfgWaitCfgEnhanced",
+ "SendTS_T",
+ "SendTstIdles",
+ "RcvTS_T",
+ "SendTst_TS1s",
+ "LTState18", "LTState19", "LTState1A", "LTState1B",
+ "LTState1C", "LTState1D", "LTState1E", "LTState1F"
};
static void __devexit ipath_remove_one(struct pci_dev *);
/* Only needed for registration, nothing else needs this info */
#define PCI_VENDOR_ID_PATHSCALE 0x1fc1
+#define PCI_VENDOR_ID_QLOGIC 0x1077
#define PCI_DEVICE_ID_INFINIPATH_HT 0xd
#define PCI_DEVICE_ID_INFINIPATH_PE800 0x10
+#define PCI_DEVICE_ID_INFINIPATH_7220 0x7220
/* Number of seconds before our card status check... */
#define STATUS_TIMEOUT 60
static const struct pci_device_id ipath_pci_tbl[] = {
{ PCI_DEVICE(PCI_VENDOR_ID_PATHSCALE, PCI_DEVICE_ID_INFINIPATH_HT) },
{ PCI_DEVICE(PCI_VENDOR_ID_PATHSCALE, PCI_DEVICE_ID_INFINIPATH_PE800) },
+ { PCI_DEVICE(PCI_VENDOR_ID_QLOGIC, PCI_DEVICE_ID_INFINIPATH_7220) },
{ 0, }
};
.probe = ipath_init_one,
.remove = __devexit_p(ipath_remove_one),
.id_table = ipath_pci_tbl,
+ .driver = {
+ .groups = ipath_driver_attr_groups,
+ },
};
-static void ipath_check_status(struct work_struct *work)
-{
- struct ipath_devdata *dd = container_of(work, struct ipath_devdata,
- status_work.work);
-
- /*
- * If we don't have any interrupts, let the user know and
- * don't bother checking again.
- */
- if (dd->ipath_int_counter == 0)
- dev_err(&dd->pcidev->dev, "No interrupts detected.\n");
-}
-
static inline void read_bars(struct ipath_devdata *dd, struct pci_dev *dev,
u32 *bar0, u32 *bar1)
{
dd->pcidev = pdev;
pci_set_drvdata(pdev, dd);
- INIT_DELAYED_WORK(&dd->status_work, ipath_check_status);
-
list_add(&dd->ipath_list, &ipath_dev_list);
bail_unlock:
return dd;
}
-int ipath_count_units(int *npresentp, int *nupp, u32 *maxportsp)
+int ipath_count_units(int *npresentp, int *nupp, int *maxportsp)
{
int nunits, npresent, nup;
struct ipath_devdata *dd;
unsigned long flags;
- u32 maxports;
+ int maxports;
nunits = npresent = nup = maxports = 0;
u32 *addr;
u64 msecs, emsecs;
- piobuf = ipath_getpiobuf(dd, &pbnum);
+ piobuf = ipath_getpiobuf(dd, 0, &pbnum);
if (!piobuf) {
dev_info(&dd->pcidev->dev,
"No PIObufs for checking perf, skipping\n");
udelay(1);
}
- writeq(0, piobuf); /* length 0, no dwords actually sent */
+ ipath_disable_armlaunch(dd);
+
+ /*
+ * length 0, no dwords actually sent, and mark as VL15
+ * on chips where that may matter (due to IB flowcontrol)
+ */
+ if ((dd->ipath_flags & IPATH_HAS_PBC_CNT))
+ writeq(1UL << 63, piobuf);
+ else
+ writeq(0, piobuf);
ipath_flush_wc();
/*
done:
/* disarm piobuf, so it's available again */
ipath_disarm_piobufs(dd, pbnum, 1);
+ ipath_enable_armlaunch(dd);
}
static int __devinit ipath_init_one(struct pci_dev *pdev,
struct ipath_devdata *dd;
unsigned long long addr;
u32 bar0 = 0, bar1 = 0;
+ u8 rev;
dd = ipath_alloc_devdata(pdev);
if (IS_ERR(dd)) {
}
addr = pci_resource_start(pdev, 0);
len = pci_resource_len(pdev, 0);
- ipath_cdbg(VERBOSE, "regbase (0) %llx len %d pdev->irq %d, vend %x/%x "
+ ipath_cdbg(VERBOSE, "regbase (0) %llx len %d irq %d, vend %x/%x "
"driver_data %lx\n", addr, len, pdev->irq, ent->vendor,
ent->device, ent->driver_data);
goto bail_disable;
}
- ret = pci_set_dma_mask(pdev, DMA_64BIT_MASK);
+ ret = pci_set_dma_mask(pdev, DMA_BIT_MASK(64));
if (ret) {
/*
* if the 64 bit setup fails, try 32 bit. Some systems
* do not setup 64 bit maps on systems with 2GB or less
* memory installed.
*/
- ret = pci_set_dma_mask(pdev, DMA_32BIT_MASK);
+ ret = pci_set_dma_mask(pdev, DMA_BIT_MASK(32));
if (ret) {
dev_info(&pdev->dev,
"Unable to set DMA mask for unit %u: %d\n",
}
else {
ipath_dbg("No 64bit DMA mask, used 32 bit mask\n");
- ret = pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK);
+ ret = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32));
if (ret)
dev_info(&pdev->dev,
"Unable to set DMA consistent mask "
}
}
else {
- ret = pci_set_consistent_dma_mask(pdev, DMA_64BIT_MASK);
+ ret = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(64));
if (ret)
dev_info(&pdev->dev,
"Unable to set DMA consistent mask "
"CONFIG_PCI_MSI is not enabled\n", ent->device);
return -ENODEV;
#endif
+ case PCI_DEVICE_ID_INFINIPATH_7220:
+#ifndef CONFIG_PCI_MSI
+ ipath_dbg("CONFIG_PCI_MSI is not enabled, "
+ "using INTx for unit %u\n", dd->ipath_unit);
+#endif
+ ipath_init_iba7220_funcs(dd);
+ break;
default:
ipath_dev_err(dd, "Found unknown QLogic deviceid 0x%x, "
"failing\n", ent->device);
goto bail_regions;
}
- dd->ipath_pcirev = pdev->revision;
+ ret = pci_read_config_byte(pdev, PCI_REVISION_ID, &rev);
+ if (ret) {
+ ipath_dev_err(dd, "Failed to read PCI revision ID unit "
+ "%u: err %d\n", dd->ipath_unit, -ret);
+ goto bail_regions; /* shouldn't ever happen */
+ }
+ dd->ipath_pcirev = rev;
#if defined(__powerpc__)
/* There isn't a generic way to specify writethrough mappings */
ipath_cdbg(VERBOSE, "mapped io addr %llx to kregbase %p\n",
addr, dd->ipath_kregbase);
- /*
- * clear ipath_flags here instead of in ipath_init_chip as it is set
- * by ipath_setup_htconfig.
- */
- dd->ipath_flags = 0;
- dd->ipath_lli_counter = 0;
- dd->ipath_lli_errors = 0;
-
if (dd->ipath_f_bus(dd, pdev))
ipath_dev_err(dd, "Failed to setup config space; "
"continuing anyway\n");
ipath_diag_add(dd);
ipath_register_ib_device(dd);
- /* Check that card status in STATUS_TIMEOUT seconds. */
- schedule_delayed_work(&dd->status_work, HZ * STATUS_TIMEOUT);
-
goto bail;
bail_irqsetup:
- if (pdev->irq) free_irq(pdev->irq, dd);
+ if (pdev->irq)
+ free_irq(pdev->irq, dd);
bail_iounmap:
iounmap((volatile void __iomem *) dd->ipath_kregbase);
static void __devexit cleanup_device(struct ipath_devdata *dd)
{
int port;
+ struct ipath_portdata **tmp;
+ unsigned long flags;
if (*dd->ipath_statusp & IPATH_STATUS_CHIP_PRESENT) {
/* can't do anything more with chip; needs re-init */
ipath_disable_wc(dd);
}
+ if (dd->ipath_spectriggerhit)
+ dev_info(&dd->pcidev->dev, "%lu special trigger hits\n",
+ dd->ipath_spectriggerhit);
+
if (dd->ipath_pioavailregs_dma) {
dma_free_coherent(&dd->pcidev->dev, PAGE_SIZE,
(void *) dd->ipath_pioavailregs_dma,
tmpp = dd->ipath_pageshadow;
dd->ipath_pageshadow = NULL;
vfree(tmpp);
+
+ dd->ipath_egrtidbase = NULL;
}
/*
* free any resources still in use (usually just kernel ports)
- * at unload; we do for portcnt, not cfgports, because cfgports
- * could have changed while we were loaded.
+ * at unload; we do for portcnt, because that's what we allocate.
+ * We acquire lock to be really paranoid that ipath_pd isn't being
+ * accessed from some interrupt-related code (that should not happen,
+ * but best to be sure).
*/
+ spin_lock_irqsave(&dd->ipath_uctxt_lock, flags);
+ tmp = dd->ipath_pd;
+ dd->ipath_pd = NULL;
+ spin_unlock_irqrestore(&dd->ipath_uctxt_lock, flags);
for (port = 0; port < dd->ipath_portcnt; port++) {
- struct ipath_portdata *pd = dd->ipath_pd[port];
- dd->ipath_pd[port] = NULL;
+ struct ipath_portdata *pd = tmp[port];
+ tmp[port] = NULL; /* debugging paranoia */
ipath_free_pddata(dd, pd);
}
- kfree(dd->ipath_pd);
- /*
- * debuggability, in case some cleanup path tries to use it
- * after this
- */
- dd->ipath_pd = NULL;
+ kfree(tmp);
}
static void __devexit ipath_remove_one(struct pci_dev *pdev)
*/
ipath_shutdown_device(dd);
- cancel_delayed_work(&dd->status_work);
flush_scheduled_work();
if (dd->verbs_dev)
unsigned cnt)
{
unsigned i, last = first + cnt;
- u64 sendctrl, sendorig;
+ unsigned long flags;
ipath_cdbg(PKT, "disarm %u PIObufs first=%u\n", cnt, first);
- sendorig = dd->ipath_sendctrl;
for (i = first; i < last; i++) {
- sendctrl = sendorig | INFINIPATH_S_DISARM |
- (i << INFINIPATH_S_DISARMPIOBUF_SHIFT);
+ spin_lock_irqsave(&dd->ipath_sendctrl_lock, flags);
+ /*
+ * The disarm-related bits are write-only, so it
+ * is ok to OR them in with our copy of sendctrl
+ * while we hold the lock.
+ */
ipath_write_kreg(dd, dd->ipath_kregs->kr_sendctrl,
- sendctrl);
+ dd->ipath_sendctrl | INFINIPATH_S_DISARM |
+ (i << INFINIPATH_S_DISARMPIOBUF_SHIFT));
+ /* can't disarm bufs back-to-back per iba7220 spec */
+ ipath_read_kreg64(dd, dd->ipath_kregs->kr_scratch);
+ spin_unlock_irqrestore(&dd->ipath_sendctrl_lock, flags);
}
-
- /*
- * Write it again with current value, in case ipath_sendctrl changed
- * while we were looping; no critical bits that would require
- * locking.
- *
- * disable PIOAVAILUPD, then re-enable, reading scratch in
- * between. This seems to avoid a chip timing race that causes
- * pioavail updates to memory to stop.
- */
- ipath_write_kreg(dd, dd->ipath_kregs->kr_sendctrl,
- sendorig & ~INFINIPATH_S_PIOBUFAVAILUPD);
- sendorig = ipath_read_kreg64(dd, dd->ipath_kregs->kr_scratch);
- ipath_write_kreg(dd, dd->ipath_kregs->kr_sendctrl,
- dd->ipath_sendctrl);
+ /* on some older chips, update may not happen after cancel */
+ ipath_force_pio_avail_update(dd);
}
/**
* -ETIMEDOUT state can have multiple states set, for any of several
* transitions.
*/
-static int ipath_wait_linkstate(struct ipath_devdata *dd, u32 state,
- int msecs)
+int ipath_wait_linkstate(struct ipath_devdata *dd, u32 state, int msecs)
{
dd->ipath_state_wanted = state;
wait_event_interruptible_timeout(ipath_state_wait,
(unsigned long long) ipath_read_kreg64(
dd, dd->ipath_kregs->kr_ibcctrl),
(unsigned long long) val,
- ipath_ibcstatus_str[val & 0xf]);
+ ipath_ibcstatus_str[val & dd->ibcs_lts_mask]);
}
return (dd->ipath_flags & state) ? 0 : -ETIMEDOUT;
}
+static void decode_sdma_errs(struct ipath_devdata *dd, ipath_err_t err,
+ char *buf, size_t blen)
+{
+ static const struct {
+ ipath_err_t err;
+ const char *msg;
+ } errs[] = {
+ { INFINIPATH_E_SDMAGENMISMATCH, "SDmaGenMismatch" },
+ { INFINIPATH_E_SDMAOUTOFBOUND, "SDmaOutOfBound" },
+ { INFINIPATH_E_SDMATAILOUTOFBOUND, "SDmaTailOutOfBound" },
+ { INFINIPATH_E_SDMABASE, "SDmaBase" },
+ { INFINIPATH_E_SDMA1STDESC, "SDma1stDesc" },
+ { INFINIPATH_E_SDMARPYTAG, "SDmaRpyTag" },
+ { INFINIPATH_E_SDMADWEN, "SDmaDwEn" },
+ { INFINIPATH_E_SDMAMISSINGDW, "SDmaMissingDw" },
+ { INFINIPATH_E_SDMAUNEXPDATA, "SDmaUnexpData" },
+ { INFINIPATH_E_SDMADESCADDRMISALIGN, "SDmaDescAddrMisalign" },
+ { INFINIPATH_E_SENDBUFMISUSE, "SendBufMisuse" },
+ { INFINIPATH_E_SDMADISABLED, "SDmaDisabled" },
+ };
+ int i;
+ int expected;
+ size_t bidx = 0;
+
+ for (i = 0; i < ARRAY_SIZE(errs); i++) {
+ expected = (errs[i].err != INFINIPATH_E_SDMADISABLED) ? 0 :
+ test_bit(IPATH_SDMA_ABORTING, &dd->ipath_sdma_status);
+ if ((err & errs[i].err) && !expected)
+ bidx += snprintf(buf + bidx, blen - bidx,
+ "%s ", errs[i].msg);
+ }
+}
+
/*
* Decode the error status into strings, deciding whether to always
* print * it or not depending on "normal packet errors" vs everything
* else. Return 1 if "real" errors, otherwise 0 if only packet
* errors, so caller can decide what to print with the string.
*/
-int ipath_decode_err(char *buf, size_t blen, ipath_err_t err)
+int ipath_decode_err(struct ipath_devdata *dd, char *buf, size_t blen,
+ ipath_err_t err)
{
int iserr = 1;
*buf = '\0';
strlcat(buf, "rbadversion ", blen);
if (err & INFINIPATH_E_RHDR)
strlcat(buf, "rhdr ", blen);
+ if (err & INFINIPATH_E_SENDSPECIALTRIGGER)
+ strlcat(buf, "sendspecialtrigger ", blen);
if (err & INFINIPATH_E_RLONGPKTLEN)
strlcat(buf, "rlongpktlen ", blen);
if (err & INFINIPATH_E_RMAXPKTLEN)
strlcat(buf, "hardware ", blen);
if (err & INFINIPATH_E_RESET)
strlcat(buf, "reset ", blen);
+ if (err & INFINIPATH_E_SDMAERRS)
+ decode_sdma_errs(dd, err, buf, blen);
+ if (err & INFINIPATH_E_INVALIDEEPCMD)
+ strlcat(buf, "invalideepromcmd ", blen);
done:
return iserr;
}
* ipath_get_egrbuf - get an eager buffer
* @dd: the infinipath device
* @bufnum: the eager buffer to get
- * @err: unused
*
* must only be called if ipath_pd[port] is known to be allocated
*/
-static inline void *ipath_get_egrbuf(struct ipath_devdata *dd, u32 bufnum,
- int err)
+static inline void *ipath_get_egrbuf(struct ipath_devdata *dd, u32 bufnum)
{
return dd->ipath_port0_skbinfo ?
(void *) dd->ipath_port0_skbinfo[bufnum].skb->data : NULL;
u32 eflags,
u32 l,
u32 etail,
- u64 *rc)
+ __le32 *rhf_addr,
+ struct ipath_message_header *hdr)
{
char emsg[128];
- struct ipath_message_header *hdr;
get_rhf_errstring(eflags, emsg, sizeof emsg);
- hdr = (struct ipath_message_header *)&rc[1];
ipath_cdbg(PKT, "RHFerrs %x hdrqtail=%x typ=%u "
"tlen=%x opcode=%x egridx=%x: %s\n",
eflags, l,
- ipath_hdrget_rcv_type((__le32 *) rc),
- ipath_hdrget_length_in_bytes((__le32 *) rc),
+ ipath_hdrget_rcv_type(rhf_addr),
+ ipath_hdrget_length_in_bytes(rhf_addr),
be32_to_cpu(hdr->bth[0]) >> 24,
etail, emsg);
/*
* ipath_kreceive - receive a packet
- * @dd: the infinipath device
+ * @pd: the infinipath port
*
* called from interrupt handler for errors or receive interrupt
*/
-void ipath_kreceive(struct ipath_devdata *dd)
+void ipath_kreceive(struct ipath_portdata *pd)
{
- u64 *rc;
+ struct ipath_devdata *dd = pd->port_dd;
+ __le32 *rhf_addr;
void *ebuf;
const u32 rsize = dd->ipath_rcvhdrentsize; /* words */
const u32 maxcnt = dd->ipath_rcvhdrcnt * rsize; /* words */
u32 etail = -1, l, hdrqtail;
struct ipath_message_header *hdr;
- u32 eflags, i, etype, tlen, pkttot = 0, updegr=0, reloop=0;
+ u32 eflags, i, etype, tlen, pkttot = 0, updegr = 0, reloop = 0;
static u64 totcalls; /* stats, may eventually remove */
+ int last;
- if (!dd->ipath_hdrqtailptr) {
- ipath_dev_err(dd,
- "hdrqtailptr not set, can't do receives\n");
- goto bail;
- }
+ l = pd->port_head;
+ rhf_addr = (__le32 *) pd->port_rcvhdrq + l + dd->ipath_rhf_offset;
+ if (dd->ipath_flags & IPATH_NODMA_RTAIL) {
+ u32 seq = ipath_hdrget_seq(rhf_addr);
- l = dd->ipath_port0head;
- hdrqtail = (u32) le64_to_cpu(*dd->ipath_hdrqtailptr);
- if (l == hdrqtail)
- goto bail;
+ if (seq != pd->port_seq_cnt)
+ goto bail;
+ hdrqtail = 0;
+ } else {
+ hdrqtail = ipath_get_rcvhdrtail(pd);
+ if (l == hdrqtail)
+ goto bail;
+ smp_rmb();
+ }
reloop:
- for (i = 0; l != hdrqtail; i++) {
- u32 qp;
- u8 *bthbytes;
-
- rc = (u64 *) (dd->ipath_pd[0]->port_rcvhdrq + (l << 2));
- hdr = (struct ipath_message_header *)&rc[1];
- /*
- * could make a network order version of IPATH_KD_QP, and
- * do the obvious shift before masking to speed this up.
- */
- qp = ntohl(hdr->bth[1]) & 0xffffff;
- bthbytes = (u8 *) hdr->bth;
-
- eflags = ipath_hdrget_err_flags((__le32 *) rc);
- etype = ipath_hdrget_rcv_type((__le32 *) rc);
+ for (last = 0, i = 1; !last; i += !last) {
+ hdr = dd->ipath_f_get_msgheader(dd, rhf_addr);
+ eflags = ipath_hdrget_err_flags(rhf_addr);
+ etype = ipath_hdrget_rcv_type(rhf_addr);
/* total length */
- tlen = ipath_hdrget_length_in_bytes((__le32 *) rc);
+ tlen = ipath_hdrget_length_in_bytes(rhf_addr);
ebuf = NULL;
- if (etype != RCVHQ_RCV_TYPE_EXPECTED) {
+ if ((dd->ipath_flags & IPATH_NODMA_RTAIL) ?
+ ipath_hdrget_use_egr_buf(rhf_addr) :
+ (etype != RCVHQ_RCV_TYPE_EXPECTED)) {
/*
- * it turns out that the chips uses an eager buffer
+ * It turns out that the chip uses an eager buffer
* for all non-expected packets, whether it "needs"
* one or not. So always get the index, but don't
* set ebuf (so we try to copy data) unless the
* length requires it.
*/
- etail = ipath_hdrget_index((__le32 *) rc);
+ etail = ipath_hdrget_index(rhf_addr);
+ updegr = 1;
if (tlen > sizeof(*hdr) ||
etype == RCVHQ_RCV_TYPE_NON_KD)
- ebuf = ipath_get_egrbuf(dd, etail, 0);
+ ebuf = ipath_get_egrbuf(dd, etail);
}
/*
* packets; only ipathhdrerr should be set.
*/
- if (etype != RCVHQ_RCV_TYPE_NON_KD && etype !=
- RCVHQ_RCV_TYPE_ERROR && ipath_hdrget_ipath_ver(
- hdr->iph.ver_port_tid_offset) !=
- IPS_PROTO_VERSION) {
+ if (etype != RCVHQ_RCV_TYPE_NON_KD &&
+ etype != RCVHQ_RCV_TYPE_ERROR &&
+ ipath_hdrget_ipath_ver(hdr->iph.ver_port_tid_offset) !=
+ IPS_PROTO_VERSION)
ipath_cdbg(PKT, "Bad InfiniPath protocol version "
"%x\n", etype);
- }
if (unlikely(eflags))
- ipath_rcv_hdrerr(dd, eflags, l, etail, rc);
+ ipath_rcv_hdrerr(dd, eflags, l, etail, rhf_addr, hdr);
else if (etype == RCVHQ_RCV_TYPE_NON_KD) {
- ipath_ib_rcv(dd->verbs_dev, rc + 1, ebuf, tlen);
+ ipath_ib_rcv(dd->verbs_dev, (u32 *)hdr, ebuf, tlen);
if (dd->ipath_lli_counter)
dd->ipath_lli_counter--;
+ } else if (etype == RCVHQ_RCV_TYPE_EAGER) {
+ u8 opcode = be32_to_cpu(hdr->bth[0]) >> 24;
+ u32 qp = be32_to_cpu(hdr->bth[1]) & 0xffffff;
ipath_cdbg(PKT, "typ %x, opcode %x (eager, "
"qp=%x), len %x; ignored\n",
- etype, bthbytes[0], qp, tlen);
+ etype, opcode, qp, tlen);
}
- else if (etype == RCVHQ_RCV_TYPE_EAGER)
- ipath_cdbg(PKT, "typ %x, opcode %x (eager, "
- "qp=%x), len %x; ignored\n",
- etype, bthbytes[0], qp, tlen);
else if (etype == RCVHQ_RCV_TYPE_EXPECTED)
ipath_dbg("Bug: Expected TID, opcode %x; ignored\n",
- be32_to_cpu(hdr->bth[0]) & 0xff);
+ be32_to_cpu(hdr->bth[0]) >> 24);
else {
/*
- * error packet, type of error unknown.
+ * error packet, type of error unknown.
* Probably type 3, but we don't know, so don't
* even try to print the opcode, etc.
+ * Usually caused by a "bad packet", that has no
+ * BTH, when the LRH says it should.
*/
- ipath_dbg("Error Pkt, but no eflags! egrbuf %x, "
- "len %x\nhdrq@%lx;hdrq+%x rhf: %llx; "
- "hdr %llx %llx %llx %llx %llx\n",
- etail, tlen, (unsigned long) rc, l,
- (unsigned long long) rc[0],
- (unsigned long long) rc[1],
- (unsigned long long) rc[2],
- (unsigned long long) rc[3],
- (unsigned long long) rc[4],
- (unsigned long long) rc[5]);
+ ipath_cdbg(ERRPKT, "Error Pkt, but no eflags! egrbuf"
+ " %x, len %x hdrq+%x rhf: %Lx\n",
+ etail, tlen, l, (unsigned long long)
+ le64_to_cpu(*(__le64 *) rhf_addr));
+ if (ipath_debug & __IPATH_ERRPKTDBG) {
+ u32 j, *d, dw = rsize-2;
+ if (rsize > (tlen>>2))
+ dw = tlen>>2;
+ d = (u32 *)hdr;
+ printk(KERN_DEBUG "EPkt rcvhdr(%x dw):\n",
+ dw);
+ for (j = 0; j < dw; j++)
+ printk(KERN_DEBUG "%8x%s", d[j],
+ (j%8) == 7 ? "\n" : " ");
+ printk(KERN_DEBUG ".\n");
+ }
}
l += rsize;
if (l >= maxcnt)
l = 0;
- if (etype != RCVHQ_RCV_TYPE_EXPECTED)
- updegr = 1;
+ rhf_addr = (__le32 *) pd->port_rcvhdrq +
+ l + dd->ipath_rhf_offset;
+ if (dd->ipath_flags & IPATH_NODMA_RTAIL) {
+ u32 seq = ipath_hdrget_seq(rhf_addr);
+
+ if (++pd->port_seq_cnt > 13)
+ pd->port_seq_cnt = 1;
+ if (seq != pd->port_seq_cnt)
+ last = 1;
+ } else if (l == hdrqtail)
+ last = 1;
/*
* update head regs on last packet, and every 16 packets.
* Reduce bus traffic, while still trying to prevent
* rcvhdrq overflows, for when the queue is nearly full
*/
- if (l == hdrqtail || (i && !(i&0xf))) {
- u64 lval;
- if (l == hdrqtail)
- /* request IBA6120 interrupt only on last */
- lval = dd->ipath_rhdrhead_intr_off | l;
- else
- lval = l;
- (void)ipath_write_ureg(dd, ur_rcvhdrhead, lval, 0);
+ if (last || !(i & 0xf)) {
+ u64 lval = l;
+
+ /* request IBA6120 and 7220 interrupt only on last */
+ if (last)
+ lval |= dd->ipath_rhdrhead_intr_off;
+ ipath_write_ureg(dd, ur_rcvhdrhead, lval,
+ pd->port_port);
if (updegr) {
- (void)ipath_write_ureg(dd, ur_rcvegrindexhead,
- etail, 0);
+ ipath_write_ureg(dd, ur_rcvegrindexhead,
+ etail, pd->port_port);
updegr = 0;
}
}
}
- if (!dd->ipath_rhdrhead_intr_off && !reloop) {
+ if (!dd->ipath_rhdrhead_intr_off && !reloop &&
+ !(dd->ipath_flags & IPATH_NODMA_RTAIL)) {
/* IBA6110 workaround; we can have a race clearing chip
* interrupt with another interrupt about to be delivered,
* and can clear it before it is delivered on the GPIO
* earlier packets, we "almost" guarantee we have covered
* that case.
*/
- u32 hqtail = (u32)le64_to_cpu(*dd->ipath_hdrqtailptr);
+ u32 hqtail = ipath_get_rcvhdrtail(pd);
if (hqtail != hdrqtail) {
hdrqtail = hqtail;
reloop = 1; /* loop 1 extra time at most */
pkttot += i;
- dd->ipath_port0head = l;
+ pd->port_head = l;
if (pkttot > ipath_stats.sps_maxpkts_call)
ipath_stats.sps_maxpkts_call = pkttot;
* happens when all buffers are in use, so only cpu overhead, not
* latency or bandwidth is affected.
*/
-#define _IPATH_ALL_CHECKBITS 0x5555555555555555ULL
if (!dd->ipath_pioavailregs_dma) {
ipath_dbg("Update shadow pioavail, but regs_dma NULL!\n");
return;
/*
* Chip Errata: bug 6641; even and odd qwords>3 are swapped
*/
- if (i > 3) {
- if (i & 1)
- piov = le64_to_cpu(
- dd->ipath_pioavailregs_dma[i - 1]);
- else
- piov = le64_to_cpu(
- dd->ipath_pioavailregs_dma[i + 1]);
- } else
+ if (i > 3 && (dd->ipath_flags & IPATH_SWAP_PIOBUFS))
+ piov = le64_to_cpu(dd->ipath_pioavailregs_dma[i ^ 1]);
+ else
piov = le64_to_cpu(dd->ipath_pioavailregs_dma[i]);
- pchg = _IPATH_ALL_CHECKBITS &
+ pchg = dd->ipath_pioavailkernel[i] &
~(dd->ipath_pioavailshadow[i] ^ piov);
pchbusy = pchg << INFINIPATH_SENDPIOAVAIL_BUSY_SHIFT;
if (pchg && (pchbusy & dd->ipath_pioavailshadow[i])) {
spin_unlock_irqrestore(&ipath_pioavail_lock, flags);
}
+/*
+ * used to force update of pioavailshadow if we can't get a pio buffer.
+ * Needed primarily due to exitting freeze mode after recovering
+ * from errors. Done lazily, because it's safer (known to not
+ * be writing pio buffers).
+ */
+static void ipath_reset_availshadow(struct ipath_devdata *dd)
+{
+ int i, im;
+ unsigned long flags;
+
+ spin_lock_irqsave(&ipath_pioavail_lock, flags);
+ for (i = 0; i < dd->ipath_pioavregs; i++) {
+ u64 val, oldval;
+ /* deal with 6110 chip bug on high register #s */
+ im = (i > 3 && (dd->ipath_flags & IPATH_SWAP_PIOBUFS)) ?
+ i ^ 1 : i;
+ val = le64_to_cpu(dd->ipath_pioavailregs_dma[im]);
+ /*
+ * busy out the buffers not in the kernel avail list,
+ * without changing the generation bits.
+ */
+ oldval = dd->ipath_pioavailshadow[i];
+ dd->ipath_pioavailshadow[i] = val |
+ ((~dd->ipath_pioavailkernel[i] <<
+ INFINIPATH_SENDPIOAVAIL_BUSY_SHIFT) &
+ 0xaaaaaaaaaaaaaaaaULL); /* All BUSY bits in qword */
+ if (oldval != dd->ipath_pioavailshadow[i])
+ ipath_dbg("shadow[%d] was %Lx, now %lx\n",
+ i, (unsigned long long) oldval,
+ dd->ipath_pioavailshadow[i]);
+ }
+ spin_unlock_irqrestore(&ipath_pioavail_lock, flags);
+}
+
/**
* ipath_setrcvhdrsize - set the receive header size
* @dd: the infinipath device
return ret;
}
-/**
- * ipath_getpiobuf - find an available pio buffer
- * @dd: the infinipath device
- * @pbufnum: the buffer number is placed here
+/*
+ * debugging code and stats updates if no pio buffers available.
+ */
+static noinline void no_pio_bufs(struct ipath_devdata *dd)
+{
+ unsigned long *shadow = dd->ipath_pioavailshadow;
+ __le64 *dma = (__le64 *)dd->ipath_pioavailregs_dma;
+
+ dd->ipath_upd_pio_shadow = 1;
+
+ /*
+ * not atomic, but if we lose a stat count in a while, that's OK
+ */
+ ipath_stats.sps_nopiobufs++;
+ if (!(++dd->ipath_consec_nopiobuf % 100000)) {
+ ipath_force_pio_avail_update(dd); /* at start */
+ ipath_dbg("%u tries no piobufavail ts%lx; dmacopy: "
+ "%llx %llx %llx %llx\n"
+ "ipath shadow: %lx %lx %lx %lx\n",
+ dd->ipath_consec_nopiobuf,
+ (unsigned long)get_cycles(),
+ (unsigned long long) le64_to_cpu(dma[0]),
+ (unsigned long long) le64_to_cpu(dma[1]),
+ (unsigned long long) le64_to_cpu(dma[2]),
+ (unsigned long long) le64_to_cpu(dma[3]),
+ shadow[0], shadow[1], shadow[2], shadow[3]);
+ /*
+ * 4 buffers per byte, 4 registers above, cover rest
+ * below
+ */
+ if ((dd->ipath_piobcnt2k + dd->ipath_piobcnt4k) >
+ (sizeof(shadow[0]) * 4 * 4))
+ ipath_dbg("2nd group: dmacopy: "
+ "%llx %llx %llx %llx\n"
+ "ipath shadow: %lx %lx %lx %lx\n",
+ (unsigned long long)le64_to_cpu(dma[4]),
+ (unsigned long long)le64_to_cpu(dma[5]),
+ (unsigned long long)le64_to_cpu(dma[6]),
+ (unsigned long long)le64_to_cpu(dma[7]),
+ shadow[4], shadow[5], shadow[6], shadow[7]);
+
+ /* at end, so update likely happened */
+ ipath_reset_availshadow(dd);
+ }
+}
+
+/*
+ * common code for normal driver pio buffer allocation, and reserved
+ * allocation.
*
* do appropriate marking as busy, etc.
* returns buffer number if one found (>=0), negative number is error.
- * Used by ipath_layer_send
*/
-u32 __iomem *ipath_getpiobuf(struct ipath_devdata *dd, u32 * pbufnum)
+static u32 __iomem *ipath_getpiobuf_range(struct ipath_devdata *dd,
+ u32 *pbufnum, u32 first, u32 last, u32 firsti)
{
- int i, j, starti, updated = 0;
- unsigned piobcnt, iter;
+ int i, j, updated = 0;
+ unsigned piobcnt;
unsigned long flags;
unsigned long *shadow = dd->ipath_pioavailshadow;
u32 __iomem *buf;
- piobcnt = (unsigned)(dd->ipath_piobcnt2k
- + dd->ipath_piobcnt4k);
- starti = dd->ipath_lastport_piobuf;
- iter = piobcnt - starti;
+ piobcnt = last - first;
if (dd->ipath_upd_pio_shadow) {
/*
* Minor optimization. If we had no buffers on last call,
* if no buffers were updated, to be paranoid
*/
ipath_update_pio_bufs(dd);
- /* we scanned here, don't do it at end of scan */
- updated = 1;
- i = starti;
+ updated++;
+ i = first;
} else
- i = dd->ipath_lastpioindex;
-
+ i = firsti;
rescan:
/*
* while test_and_set_bit() is atomic, we do that and then the
* of the remaining armlaunch errors.
*/
spin_lock_irqsave(&ipath_pioavail_lock, flags);
- for (j = 0; j < iter; j++, i++) {
- if (i >= piobcnt)
- i = starti;
- /*
- * To avoid bus lock overhead, we first find a candidate
- * buffer, then do the test and set, and continue if that
- * fails.
- */
- if (test_bit((2 * i) + 1, shadow) ||
- test_and_set_bit((2 * i) + 1, shadow))
+ for (j = 0; j < piobcnt; j++, i++) {
+ if (i >= last)
+ i = first;
+ if (__test_and_set_bit((2 * i) + 1, shadow))
continue;
/* flip generation bit */
- change_bit(2 * i, shadow);
+ __change_bit(2 * i, shadow);
break;
}
spin_unlock_irqrestore(&ipath_pioavail_lock, flags);
- if (j == iter) {
- volatile __le64 *dma = dd->ipath_pioavailregs_dma;
-
- /*
- * first time through; shadow exhausted, but may be real
- * buffers available, so go see; if any updated, rescan
- * (once)
- */
+ if (j == piobcnt) {
if (!updated) {
+ /*
+ * first time through; shadow exhausted, but may be
+ * buffers available, try an update and then rescan.
+ */
ipath_update_pio_bufs(dd);
- updated = 1;
- i = starti;
+ updated++;
+ i = first;
+ goto rescan;
+ } else if (updated == 1 && piobcnt <=
+ ((dd->ipath_sendctrl
+ >> INFINIPATH_S_UPDTHRESH_SHIFT) &
+ INFINIPATH_S_UPDTHRESH_MASK)) {
+ /*
+ * for chips supporting and using the update
+ * threshold we need to force an update of the
+ * in-memory copy if the count is less than the
+ * thershold, then check one more time.
+ */
+ ipath_force_pio_avail_update(dd);
+ ipath_update_pio_bufs(dd);
+ updated++;
+ i = first;
goto rescan;
}
- dd->ipath_upd_pio_shadow = 1;
+
+ no_pio_bufs(dd);
+ buf = NULL;
+ } else {
+ if (i < dd->ipath_piobcnt2k)
+ buf = (u32 __iomem *) (dd->ipath_pio2kbase +
+ i * dd->ipath_palign);
+ else
+ buf = (u32 __iomem *)
+ (dd->ipath_pio4kbase +
+ (i - dd->ipath_piobcnt2k) * dd->ipath_4kalign);
+ if (pbufnum)
+ *pbufnum = i;
+ }
+
+ return buf;
+}
+
+/**
+ * ipath_getpiobuf - find an available pio buffer
+ * @dd: the infinipath device
+ * @plen: the size of the PIO buffer needed in 32-bit words
+ * @pbufnum: the buffer number is placed here
+ */
+u32 __iomem *ipath_getpiobuf(struct ipath_devdata *dd, u32 plen, u32 *pbufnum)
+{
+ u32 __iomem *buf;
+ u32 pnum, nbufs;
+ u32 first, lasti;
+
+ if (plen + 1 >= IPATH_SMALLBUF_DWORDS) {
+ first = dd->ipath_piobcnt2k;
+ lasti = dd->ipath_lastpioindexl;
+ } else {
+ first = 0;
+ lasti = dd->ipath_lastpioindex;
+ }
+ nbufs = dd->ipath_piobcnt2k + dd->ipath_piobcnt4k;
+ buf = ipath_getpiobuf_range(dd, &pnum, first, nbufs, lasti);
+
+ if (buf) {
/*
- * not atomic, but if we lose one once in a while, that's OK
+ * Set next starting place. It's just an optimization,
+ * it doesn't matter who wins on this, so no locking
*/
- ipath_stats.sps_nopiobufs++;
- if (!(++dd->ipath_consec_nopiobuf % 100000)) {
- ipath_dbg(
- "%u pio sends with no bufavail; dmacopy: "
- "%llx %llx %llx %llx; shadow: "
- "%lx %lx %lx %lx\n",
- dd->ipath_consec_nopiobuf,
- (unsigned long long) le64_to_cpu(dma[0]),
- (unsigned long long) le64_to_cpu(dma[1]),
- (unsigned long long) le64_to_cpu(dma[2]),
- (unsigned long long) le64_to_cpu(dma[3]),
- shadow[0], shadow[1], shadow[2],
- shadow[3]);
+ if (plen + 1 >= IPATH_SMALLBUF_DWORDS)
+ dd->ipath_lastpioindexl = pnum + 1;
+ else
+ dd->ipath_lastpioindex = pnum + 1;
+ if (dd->ipath_upd_pio_shadow)
+ dd->ipath_upd_pio_shadow = 0;
+ if (dd->ipath_consec_nopiobuf)
+ dd->ipath_consec_nopiobuf = 0;
+ ipath_cdbg(VERBOSE, "Return piobuf%u %uk @ %p\n",
+ pnum, (pnum < dd->ipath_piobcnt2k) ? 2 : 4, buf);
+ if (pbufnum)
+ *pbufnum = pnum;
+
+ }
+ return buf;
+}
+
+/**
+ * ipath_chg_pioavailkernel - change which send buffers are available for kernel
+ * @dd: the infinipath device
+ * @start: the starting send buffer number
+ * @len: the number of send buffers
+ * @avail: true if the buffers are available for kernel use, false otherwise
+ */
+void ipath_chg_pioavailkernel(struct ipath_devdata *dd, unsigned start,
+ unsigned len, int avail)
+{
+ unsigned long flags;
+ unsigned end, cnt = 0, next;
+
+ /* There are two bits per send buffer (busy and generation) */
+ start *= 2;
+ end = start + len * 2;
+
+ spin_lock_irqsave(&ipath_pioavail_lock, flags);
+ /* Set or clear the busy bit in the shadow. */
+ while (start < end) {
+ if (avail) {
+ unsigned long dma;
+ int i, im;
/*
- * 4 buffers per byte, 4 registers above, cover rest
- * below
+ * the BUSY bit will never be set, because we disarm
+ * the user buffers before we hand them back to the
+ * kernel. We do have to make sure the generation
+ * bit is set correctly in shadow, since it could
+ * have changed many times while allocated to user.
+ * We can't use the bitmap functions on the full
+ * dma array because it is always little-endian, so
+ * we have to flip to host-order first.
+ * BITS_PER_LONG is slightly wrong, since it's
+ * always 64 bits per register in chip...
+ * We only work on 64 bit kernels, so that's OK.
*/
- if ((dd->ipath_piobcnt2k + dd->ipath_piobcnt4k) >
- (sizeof(shadow[0]) * 4 * 4))
- ipath_dbg("2nd group: dmacopy: %llx %llx "
- "%llx %llx; shadow: %lx %lx "
- "%lx %lx\n",
- (unsigned long long)
- le64_to_cpu(dma[4]),
- (unsigned long long)
- le64_to_cpu(dma[5]),
- (unsigned long long)
- le64_to_cpu(dma[6]),
- (unsigned long long)
- le64_to_cpu(dma[7]),
- shadow[4], shadow[5],
- shadow[6], shadow[7]);
+ /* deal with 6110 chip bug on high register #s */
+ i = start / BITS_PER_LONG;
+ im = (i > 3 && (dd->ipath_flags & IPATH_SWAP_PIOBUFS)) ?
+ i ^ 1 : i;
+ __clear_bit(INFINIPATH_SENDPIOAVAIL_BUSY_SHIFT
+ + start, dd->ipath_pioavailshadow);
+ dma = (unsigned long) le64_to_cpu(
+ dd->ipath_pioavailregs_dma[im]);
+ if (test_bit((INFINIPATH_SENDPIOAVAIL_CHECK_SHIFT
+ + start) % BITS_PER_LONG, &dma))
+ __set_bit(INFINIPATH_SENDPIOAVAIL_CHECK_SHIFT
+ + start, dd->ipath_pioavailshadow);
+ else
+ __clear_bit(INFINIPATH_SENDPIOAVAIL_CHECK_SHIFT
+ + start, dd->ipath_pioavailshadow);
+ __set_bit(start, dd->ipath_pioavailkernel);
+ } else {
+ __set_bit(start + INFINIPATH_SENDPIOAVAIL_BUSY_SHIFT,
+ dd->ipath_pioavailshadow);
+ __clear_bit(start, dd->ipath_pioavailkernel);
+ }
+ start += 2;
+ }
+
+ if (dd->ipath_pioupd_thresh) {
+ end = 2 * (dd->ipath_piobcnt2k + dd->ipath_piobcnt4k);
+ next = find_first_bit(dd->ipath_pioavailkernel, end);
+ while (next < end) {
+ cnt++;
+ next = find_next_bit(dd->ipath_pioavailkernel, end,
+ next + 1);
}
- buf = NULL;
- goto bail;
}
+ spin_unlock_irqrestore(&ipath_pioavail_lock, flags);
/*
- * set next starting place. Since it's just an optimization,
- * it doesn't matter who wins on this, so no locking
+ * When moving buffers from kernel to user, if number assigned to
+ * the user is less than the pio update threshold, and threshold
+ * is supported (cnt was computed > 0), drop the update threshold
+ * so we update at least once per allocated number of buffers.
+ * In any case, if the kernel buffers are less than the threshold,
+ * drop the threshold. We don't bother increasing it, having once
+ * decreased it, since it would typically just cycle back and forth.
+ * If we don't decrease below buffers in use, we can wait a long
+ * time for an update, until some other context uses PIO buffers.
*/
- dd->ipath_lastpioindex = i + 1;
- if (dd->ipath_upd_pio_shadow)
- dd->ipath_upd_pio_shadow = 0;
- if (dd->ipath_consec_nopiobuf)
- dd->ipath_consec_nopiobuf = 0;
- if (i < dd->ipath_piobcnt2k)
- buf = (u32 __iomem *) (dd->ipath_pio2kbase +
- i * dd->ipath_palign);
- else
- buf = (u32 __iomem *)
- (dd->ipath_pio4kbase +
- (i - dd->ipath_piobcnt2k) * dd->ipath_4kalign);
- ipath_cdbg(VERBOSE, "Return piobuf%u %uk @ %p\n",
- i, (i < dd->ipath_piobcnt2k) ? 2 : 4, buf);
- if (pbufnum)
- *pbufnum = i;
-
-bail:
- return buf;
+ if (!avail && len < cnt)
+ cnt = len;
+ if (cnt < dd->ipath_pioupd_thresh) {
+ dd->ipath_pioupd_thresh = cnt;
+ ipath_dbg("Decreased pio update threshold to %u\n",
+ dd->ipath_pioupd_thresh);
+ spin_lock_irqsave(&dd->ipath_sendctrl_lock, flags);
+ dd->ipath_sendctrl &= ~(INFINIPATH_S_UPDTHRESH_MASK
+ << INFINIPATH_S_UPDTHRESH_SHIFT);
+ dd->ipath_sendctrl |= dd->ipath_pioupd_thresh
+ << INFINIPATH_S_UPDTHRESH_SHIFT;
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_sendctrl,
+ dd->ipath_sendctrl);
+ spin_unlock_irqrestore(&dd->ipath_sendctrl_lock, flags);
+ }
}
/**
ret = -ENOMEM;
goto bail;
}
- pd->port_rcvhdrtail_kvaddr = dma_alloc_coherent(
- &dd->pcidev->dev, PAGE_SIZE, &phys_hdrqtail, GFP_KERNEL);
- if (!pd->port_rcvhdrtail_kvaddr) {
- ipath_dev_err(dd, "attempt to allocate 1 page "
- "for port %u rcvhdrqtailaddr failed\n",
- pd->port_port);
- ret = -ENOMEM;
- dma_free_coherent(&dd->pcidev->dev, amt,
- pd->port_rcvhdrq, pd->port_rcvhdrq_phys);
- pd->port_rcvhdrq = NULL;
- goto bail;
+
+ if (!(dd->ipath_flags & IPATH_NODMA_RTAIL)) {
+ pd->port_rcvhdrtail_kvaddr = dma_alloc_coherent(
+ &dd->pcidev->dev, PAGE_SIZE, &phys_hdrqtail,
+ GFP_KERNEL);
+ if (!pd->port_rcvhdrtail_kvaddr) {
+ ipath_dev_err(dd, "attempt to allocate 1 page "
+ "for port %u rcvhdrqtailaddr "
+ "failed\n", pd->port_port);
+ ret = -ENOMEM;
+ dma_free_coherent(&dd->pcidev->dev, amt,
+ pd->port_rcvhdrq,
+ pd->port_rcvhdrq_phys);
+ pd->port_rcvhdrq = NULL;
+ goto bail;
+ }
+ pd->port_rcvhdrqtailaddr_phys = phys_hdrqtail;
+ ipath_cdbg(VERBOSE, "port %d hdrtailaddr, %llx "
+ "physical\n", pd->port_port,
+ (unsigned long long) phys_hdrqtail);
}
- pd->port_rcvhdrqtailaddr_phys = phys_hdrqtail;
pd->port_rcvhdrq_size = amt;
(unsigned long) pd->port_rcvhdrq_phys,
(unsigned long) pd->port_rcvhdrq_size,
pd->port_port);
-
- ipath_cdbg(VERBOSE, "port %d hdrtailaddr, %llx physical\n",
- pd->port_port,
- (unsigned long long) phys_hdrqtail);
}
else
ipath_cdbg(VERBOSE, "reuse port %d rcvhdrq @%p %llx phys; "
/* clear for security and sanity on each use */
memset(pd->port_rcvhdrq, 0, pd->port_rcvhdrq_size);
- memset(pd->port_rcvhdrtail_kvaddr, 0, PAGE_SIZE);
+ if (pd->port_rcvhdrtail_kvaddr)
+ memset(pd->port_rcvhdrtail_kvaddr, 0, PAGE_SIZE);
/*
* tell chip each time we init it, even if we are re-using previous
ipath_write_kreg_port(dd, dd->ipath_kregs->kr_rcvhdraddr,
pd->port_port, pd->port_rcvhdrq_phys);
- ret = 0;
bail:
return ret;
}
-int ipath_waitfor_complete(struct ipath_devdata *dd, ipath_kreg reg_id,
- u64 bits_to_wait_for, u64 * valp)
-{
- unsigned long timeout;
- u64 lastval, val;
- int ret;
-
- lastval = ipath_read_kreg64(dd, reg_id);
- /* wait a ridiculously long time */
- timeout = jiffies + msecs_to_jiffies(5);
- do {
- val = ipath_read_kreg64(dd, reg_id);
- /* set so they have something, even on failures. */
- *valp = val;
- if ((val & bits_to_wait_for) == bits_to_wait_for) {
- ret = 0;
- break;
- }
- if (val != lastval)
- ipath_cdbg(VERBOSE, "Changed from %llx to %llx, "
- "waiting for %llx bits\n",
- (unsigned long long) lastval,
- (unsigned long long) val,
- (unsigned long long) bits_to_wait_for);
- cond_resched();
- if (time_after(jiffies, timeout)) {
- ipath_dbg("Didn't get bits %llx in register 0x%x, "
- "got %llx\n",
- (unsigned long long) bits_to_wait_for,
- reg_id, (unsigned long long) *valp);
- ret = -ENODEV;
- break;
- }
- } while (1);
-
- return ret;
-}
-
-/**
- * ipath_waitfor_mdio_cmdready - wait for last command to complete
- * @dd: the infinipath device
- *
- * Like ipath_waitfor_complete(), but we wait for the CMDVALID bit to go
- * away indicating the last command has completed. It doesn't return data
- */
-int ipath_waitfor_mdio_cmdready(struct ipath_devdata *dd)
-{
- unsigned long timeout;
- u64 val;
- int ret;
-
- /* wait a ridiculously long time */
- timeout = jiffies + msecs_to_jiffies(5);
- do {
- val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_mdio);
- if (!(val & IPATH_MDIO_CMDVALID)) {
- ret = 0;
- break;
- }
- cond_resched();
- if (time_after(jiffies, timeout)) {
- ipath_dbg("CMDVALID stuck in mdio reg? (%llx)\n",
- (unsigned long long) val);
- ret = -ENODEV;
- break;
- }
- } while (1);
-
- return ret;
-}
-
/*
* Flush all sends that might be in the ready to send state, as well as any
*/
void ipath_cancel_sends(struct ipath_devdata *dd, int restore_sendctrl)
{
+ unsigned long flags;
+
+ if (dd->ipath_flags & IPATH_IB_AUTONEG_INPROG) {
+ ipath_cdbg(VERBOSE, "Ignore while in autonegotiation\n");
+ goto bail;
+ }
+ /*
+ * If we have SDMA, and it's not disabled, we have to kick off the
+ * abort state machine, provided we aren't already aborting.
+ * If we are in the process of aborting SDMA (!DISABLED, but ABORTING),
+ * we skip the rest of this routine. It is already "in progress"
+ */
+ if (dd->ipath_flags & IPATH_HAS_SEND_DMA) {
+ int skip_cancel;
+ unsigned long *statp = &dd->ipath_sdma_status;
+
+ spin_lock_irqsave(&dd->ipath_sdma_lock, flags);
+ skip_cancel =
+ test_and_set_bit(IPATH_SDMA_ABORTING, statp)
+ && !test_bit(IPATH_SDMA_DISABLED, statp);
+ spin_unlock_irqrestore(&dd->ipath_sdma_lock, flags);
+ if (skip_cancel)
+ goto bail;
+ }
+
ipath_dbg("Cancelling all in-progress send buffers\n");
- dd->ipath_lastcancel = jiffies+HZ/2; /* skip armlaunch errs a bit */
+
+ /* skip armlaunch errs for a while */
+ dd->ipath_lastcancel = jiffies + HZ / 2;
+
/*
- * the abort bit is auto-clearing. We read scratch to be sure
- * that cancels and the abort have taken effect in the chip.
+ * The abort bit is auto-clearing. We also don't want pioavail
+ * update happening during this, and we don't want any other
+ * sends going out, so turn those off for the duration. We read
+ * the scratch register to be sure that cancels and the abort
+ * have taken effect in the chip. Otherwise two parts are same
+ * as ipath_force_pio_avail_update()
*/
+ spin_lock_irqsave(&dd->ipath_sendctrl_lock, flags);
+ dd->ipath_sendctrl &= ~(INFINIPATH_S_PIOBUFAVAILUPD
+ | INFINIPATH_S_PIOENABLE);
ipath_write_kreg(dd, dd->ipath_kregs->kr_sendctrl,
- INFINIPATH_S_ABORT);
+ dd->ipath_sendctrl | INFINIPATH_S_ABORT);
ipath_read_kreg64(dd, dd->ipath_kregs->kr_scratch);
+ spin_unlock_irqrestore(&dd->ipath_sendctrl_lock, flags);
+
+ /* disarm all send buffers */
ipath_disarm_piobufs(dd, 0,
- (unsigned)(dd->ipath_piobcnt2k + dd->ipath_piobcnt4k));
- if (restore_sendctrl) /* else done by caller later */
+ dd->ipath_piobcnt2k + dd->ipath_piobcnt4k);
+
+ if (dd->ipath_flags & IPATH_HAS_SEND_DMA)
+ set_bit(IPATH_SDMA_DISARMED, &dd->ipath_sdma_status);
+
+ if (restore_sendctrl) {
+ /* else done by caller later if needed */
+ spin_lock_irqsave(&dd->ipath_sendctrl_lock, flags);
+ dd->ipath_sendctrl |= INFINIPATH_S_PIOBUFAVAILUPD |
+ INFINIPATH_S_PIOENABLE;
ipath_write_kreg(dd, dd->ipath_kregs->kr_sendctrl,
- dd->ipath_sendctrl);
+ dd->ipath_sendctrl);
+ /* and again, be sure all have hit the chip */
+ ipath_read_kreg64(dd, dd->ipath_kregs->kr_scratch);
+ spin_unlock_irqrestore(&dd->ipath_sendctrl_lock, flags);
+ }
- /* and again, be sure all have hit the chip */
- ipath_read_kreg64(dd, dd->ipath_kregs->kr_scratch);
+ if ((dd->ipath_flags & IPATH_HAS_SEND_DMA) &&
+ !test_bit(IPATH_SDMA_DISABLED, &dd->ipath_sdma_status) &&
+ test_bit(IPATH_SDMA_RUNNING, &dd->ipath_sdma_status)) {
+ spin_lock_irqsave(&dd->ipath_sdma_lock, flags);
+ /* only wait so long for intr */
+ dd->ipath_sdma_abort_intr_timeout = jiffies + HZ;
+ dd->ipath_sdma_reset_wait = 200;
+ if (!test_bit(IPATH_SDMA_SHUTDOWN, &dd->ipath_sdma_status))
+ tasklet_hi_schedule(&dd->ipath_sdma_abort_task);
+ spin_unlock_irqrestore(&dd->ipath_sdma_lock, flags);
+ }
+bail:;
}
+/*
+ * Force an update of in-memory copy of the pioavail registers, when
+ * needed for any of a variety of reasons. We read the scratch register
+ * to make it highly likely that the update will have happened by the
+ * time we return. If already off (as in cancel_sends above), this
+ * routine is a nop, on the assumption that the caller will "do the
+ * right thing".
+ */
+void ipath_force_pio_avail_update(struct ipath_devdata *dd)
+{
+ unsigned long flags;
-static void ipath_set_ib_lstate(struct ipath_devdata *dd, int which)
+ spin_lock_irqsave(&dd->ipath_sendctrl_lock, flags);
+ if (dd->ipath_sendctrl & INFINIPATH_S_PIOBUFAVAILUPD) {
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_sendctrl,
+ dd->ipath_sendctrl & ~INFINIPATH_S_PIOBUFAVAILUPD);
+ ipath_read_kreg64(dd, dd->ipath_kregs->kr_scratch);
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_sendctrl,
+ dd->ipath_sendctrl);
+ ipath_read_kreg64(dd, dd->ipath_kregs->kr_scratch);
+ }
+ spin_unlock_irqrestore(&dd->ipath_sendctrl_lock, flags);
+}
+
+static void ipath_set_ib_lstate(struct ipath_devdata *dd, int linkcmd,
+ int linitcmd)
{
+ u64 mod_wd;
static const char *what[4] = {
- [0] = "DOWN",
- [INFINIPATH_IBCC_LINKCMD_INIT] = "INIT",
+ [0] = "NOP",
+ [INFINIPATH_IBCC_LINKCMD_DOWN] = "DOWN",
[INFINIPATH_IBCC_LINKCMD_ARMED] = "ARMED",
[INFINIPATH_IBCC_LINKCMD_ACTIVE] = "ACTIVE"
};
- int linkcmd = (which >> INFINIPATH_IBCC_LINKCMD_SHIFT) &
- INFINIPATH_IBCC_LINKCMD_MASK;
-
- ipath_cdbg(VERBOSE, "Trying to move unit %u to %s, current ltstate "
- "is %s\n", dd->ipath_unit,
- what[linkcmd],
- ipath_ibcstatus_str[
- (ipath_read_kreg64
- (dd, dd->ipath_kregs->kr_ibcstatus) >>
- INFINIPATH_IBCS_LINKTRAININGSTATE_SHIFT) &
- INFINIPATH_IBCS_LINKTRAININGSTATE_MASK]);
- /* flush all queued sends when going to DOWN or INIT, to be sure that
- * they don't block MAD packets */
- if (!linkcmd || linkcmd == INFINIPATH_IBCC_LINKCMD_INIT)
- ipath_cancel_sends(dd, 1);
+
+ if (linitcmd == INFINIPATH_IBCC_LINKINITCMD_DISABLE) {
+ /*
+ * If we are told to disable, note that so link-recovery
+ * code does not attempt to bring us back up.
+ */
+ preempt_disable();
+ dd->ipath_flags |= IPATH_IB_LINK_DISABLED;
+ preempt_enable();
+ } else if (linitcmd) {
+ /*
+ * Any other linkinitcmd will lead to LINKDOWN and then
+ * to INIT (if all is well), so clear flag to let
+ * link-recovery code attempt to bring us back up.
+ */
+ preempt_disable();
+ dd->ipath_flags &= ~IPATH_IB_LINK_DISABLED;
+ preempt_enable();
+ }
+
+ mod_wd = (linkcmd << dd->ibcc_lc_shift) |
+ (linitcmd << INFINIPATH_IBCC_LINKINITCMD_SHIFT);
+ ipath_cdbg(VERBOSE,
+ "Moving unit %u to %s (initcmd=0x%x), current ltstate is %s\n",
+ dd->ipath_unit, what[linkcmd], linitcmd,
+ ipath_ibcstatus_str[ipath_ib_linktrstate(dd,
+ ipath_read_kreg64(dd, dd->ipath_kregs->kr_ibcstatus))]);
ipath_write_kreg(dd, dd->ipath_kregs->kr_ibcctrl,
- dd->ipath_ibcctrl | which);
+ dd->ipath_ibcctrl | mod_wd);
+ /* read from chip so write is flushed */
+ (void) ipath_read_kreg64(dd, dd->ipath_kregs->kr_ibcstatus);
}
int ipath_set_linkstate(struct ipath_devdata *dd, u8 newstate)
int ret;
switch (newstate) {
+ case IPATH_IB_LINKDOWN_ONLY:
+ ipath_set_ib_lstate(dd, INFINIPATH_IBCC_LINKCMD_DOWN, 0);
+ /* don't wait */
+ ret = 0;
+ goto bail;
+
case IPATH_IB_LINKDOWN:
- ipath_set_ib_lstate(dd, INFINIPATH_IBCC_LINKINITCMD_POLL <<
- INFINIPATH_IBCC_LINKINITCMD_SHIFT);
+ ipath_set_ib_lstate(dd, INFINIPATH_IBCC_LINKCMD_DOWN,
+ INFINIPATH_IBCC_LINKINITCMD_POLL);
/* don't wait */
ret = 0;
goto bail;
case IPATH_IB_LINKDOWN_SLEEP:
- ipath_set_ib_lstate(dd, INFINIPATH_IBCC_LINKINITCMD_SLEEP <<
- INFINIPATH_IBCC_LINKINITCMD_SHIFT);
+ ipath_set_ib_lstate(dd, INFINIPATH_IBCC_LINKCMD_DOWN,
+ INFINIPATH_IBCC_LINKINITCMD_SLEEP);
/* don't wait */
ret = 0;
goto bail;
case IPATH_IB_LINKDOWN_DISABLE:
- ipath_set_ib_lstate(dd,
- INFINIPATH_IBCC_LINKINITCMD_DISABLE <<
- INFINIPATH_IBCC_LINKINITCMD_SHIFT);
+ ipath_set_ib_lstate(dd, INFINIPATH_IBCC_LINKCMD_DOWN,
+ INFINIPATH_IBCC_LINKINITCMD_DISABLE);
/* don't wait */
ret = 0;
goto bail;
- case IPATH_IB_LINKINIT:
- if (dd->ipath_flags & IPATH_LINKINIT) {
- ret = 0;
- goto bail;
- }
- ipath_set_ib_lstate(dd, INFINIPATH_IBCC_LINKCMD_INIT <<
- INFINIPATH_IBCC_LINKCMD_SHIFT);
- lstate = IPATH_LINKINIT;
- break;
-
case IPATH_IB_LINKARM:
if (dd->ipath_flags & IPATH_LINKARMED) {
ret = 0;
ret = -EINVAL;
goto bail;
}
- ipath_set_ib_lstate(dd, INFINIPATH_IBCC_LINKCMD_ARMED <<
- INFINIPATH_IBCC_LINKCMD_SHIFT);
+ ipath_set_ib_lstate(dd, INFINIPATH_IBCC_LINKCMD_ARMED, 0);
+
/*
* Since the port can transition to ACTIVE by receiving
* a non VL 15 packet, wait for either state.
ret = -EINVAL;
goto bail;
}
- ipath_set_ib_lstate(dd, INFINIPATH_IBCC_LINKCMD_ACTIVE <<
- INFINIPATH_IBCC_LINKCMD_SHIFT);
+ ipath_set_ib_lstate(dd, INFINIPATH_IBCC_LINKCMD_ACTIVE, 0);
lstate = IPATH_LINKACTIVE;
break;
dd->ipath_ibcctrl |= INFINIPATH_IBCC_LOOPBACK;
ipath_write_kreg(dd, dd->ipath_kregs->kr_ibcctrl,
dd->ipath_ibcctrl);
+
+ /* turn heartbeat off, as it causes loopback to fail */
+ dd->ipath_f_set_ib_cfg(dd, IPATH_IB_CFG_HRTBT,
+ IPATH_IB_HRTBT_OFF);
+ /* don't wait */
ret = 0;
- goto bail; // no state change to wait for
+ goto bail;
case IPATH_IB_LINK_EXTERNAL:
- dev_info(&dd->pcidev->dev, "Disabling IB local loopback (normal)\n");
+ dev_info(&dd->pcidev->dev,
+ "Disabling IB local loopback (normal)\n");
+ dd->ipath_f_set_ib_cfg(dd, IPATH_IB_CFG_HRTBT,
+ IPATH_IB_HRTBT_ON);
dd->ipath_ibcctrl &= ~INFINIPATH_IBCC_LOOPBACK;
ipath_write_kreg(dd, dd->ipath_kregs->kr_ibcctrl,
dd->ipath_ibcctrl);
+ /* don't wait */
ret = 0;
- goto bail; // no state change to wait for
+ goto bail;
+
+ /*
+ * Heartbeat can be explicitly enabled by the user via
+ * "hrtbt_enable" "file", and if disabled, trying to enable here
+ * will have no effect. Implicit changes (heartbeat off when
+ * loopback on, and vice versa) are included to ease testing.
+ */
+ case IPATH_IB_LINK_HRTBT:
+ ret = dd->ipath_f_set_ib_cfg(dd, IPATH_IB_CFG_HRTBT,
+ IPATH_IB_HRTBT_ON);
+ goto bail;
+
+ case IPATH_IB_LINK_NO_HRTBT:
+ ret = dd->ipath_f_set_ib_cfg(dd, IPATH_IB_CFG_HRTBT,
+ IPATH_IB_HRTBT_OFF);
+ goto bail;
default:
ipath_dbg("Invalid linkstate 0x%x requested\n", newstate);
* sanity checking on this, and we don't deal with what happens to
* programs that are already running when the size changes.
* NOTE: changing the MTU will usually cause the IBC to go back to
- * link initialize (IPATH_IBSTATE_INIT) state...
+ * link INIT state...
*/
int ipath_set_mtu(struct ipath_devdata *dd, u16 arg)
{
* piosize). We check that it's one of the valid IB sizes.
*/
if (arg != 256 && arg != 512 && arg != 1024 && arg != 2048 &&
- arg != 4096) {
+ (arg != 4096 || !ipath_mtu4096)) {
ipath_dbg("Trying to set invalid mtu %u, failing\n", arg);
ret = -EINVAL;
goto bail;
if (arg >= (piosize - IPATH_PIO_MAXIBHDR)) {
/* Only if it's not the initial value (or reset to it) */
if (piosize != dd->ipath_init_ibmaxlen) {
+ if (arg > piosize && arg <= dd->ipath_init_ibmaxlen)
+ piosize = dd->ipath_init_ibmaxlen;
dd->ipath_ibmaxlen = piosize;
changed = 1;
}
}
if (changed) {
+ u64 ibc = dd->ipath_ibcctrl, ibdw;
/*
- * set the IBC maxpktlength to the size of our pio
- * buffers in words
+ * update our housekeeping variables, and set IBC max
+ * size, same as init code; max IBC is max we allow in
+ * buffer, less the qword pbc, plus 1 for ICRC, in dwords
*/
- u64 ibc = dd->ipath_ibcctrl;
+ dd->ipath_ibmaxlen = piosize - 2 * sizeof(u32);
+ ibdw = (dd->ipath_ibmaxlen >> 2) + 1;
ibc &= ~(INFINIPATH_IBCC_MAXPKTLEN_MASK <<
- INFINIPATH_IBCC_MAXPKTLEN_SHIFT);
-
- piosize = piosize - 2 * sizeof(u32); /* ignore pbc */
- dd->ipath_ibmaxlen = piosize;
- piosize /= sizeof(u32); /* in words */
- /*
- * for ICRC, which we only send in diag test pkt mode, and
- * we don't need to worry about that for mtu
- */
- piosize += 1;
-
- ibc |= piosize << INFINIPATH_IBCC_MAXPKTLEN_SHIFT;
+ dd->ibcc_mpl_shift);
+ ibc |= ibdw << dd->ibcc_mpl_shift;
dd->ipath_ibcctrl = ibc;
ipath_write_kreg(dd, dd->ipath_kregs->kr_ibcctrl,
dd->ipath_ibcctrl);
return ret;
}
-int ipath_set_lid(struct ipath_devdata *dd, u32 arg, u8 lmc)
+int ipath_set_lid(struct ipath_devdata *dd, u32 lid, u8 lmc)
{
- dd->ipath_lid = arg;
+ dd->ipath_lid = lid;
dd->ipath_lmc = lmc;
+ dd->ipath_f_set_ib_cfg(dd, IPATH_IB_CFG_LIDLMC, lid |
+ (~((1U << lmc) - 1)) << 16);
+
+ dev_info(&dd->pcidev->dev, "We got a lid: 0x%x\n", lid);
+
return 0;
}
* but leave that to per-chip functions.
*/
val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_ibcstatus);
- ltstate = (val >> INFINIPATH_IBCS_LINKTRAININGSTATE_SHIFT) &
- INFINIPATH_IBCS_LINKTRAININGSTATE_MASK;
- lstate = (val >> INFINIPATH_IBCS_LINKSTATE_SHIFT) &
- INFINIPATH_IBCS_LINKSTATE_MASK;
+ ltstate = ipath_ib_linktrstate(dd, val);
+ lstate = ipath_ib_linkstate(dd, val);
dd->ipath_f_setextled(dd, lstate, ltstate);
mod_timer(&dd->ipath_led_override_timer, jiffies + timeoff);
dd->ipath_led_override_timer.data = (unsigned long) dd;
dd->ipath_led_override_timer.expires = jiffies + 1;
add_timer(&dd->ipath_led_override_timer);
- } else {
+ } else
atomic_dec(&dd->ipath_led_override_timer_active);
- }
}
/**
*/
void ipath_shutdown_device(struct ipath_devdata *dd)
{
+ unsigned long flags;
+
ipath_dbg("Shutting down the device\n");
+ ipath_hol_up(dd); /* make sure user processes aren't suspended */
+
dd->ipath_flags |= IPATH_LINKUNK;
dd->ipath_flags &= ~(IPATH_INITTED | IPATH_LINKDOWN |
IPATH_LINKINIT | IPATH_LINKARMED |
ipath_write_kreg(dd, dd->ipath_kregs->kr_rcvctrl,
dd->ipath_rcvctrl);
+ if (dd->ipath_flags & IPATH_HAS_SEND_DMA)
+ teardown_sdma(dd);
+
/*
* gracefully stop all sends allowing any in progress to trickle out
* first.
*/
- ipath_write_kreg(dd, dd->ipath_kregs->kr_sendctrl, 0ULL);
+ spin_lock_irqsave(&dd->ipath_sendctrl_lock, flags);
+ dd->ipath_sendctrl = 0;
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_sendctrl, dd->ipath_sendctrl);
/* flush it */
ipath_read_kreg64(dd, dd->ipath_kregs->kr_scratch);
+ spin_unlock_irqrestore(&dd->ipath_sendctrl_lock, flags);
+
/*
* enough for anything that's going to trickle out to have actually
* done so.
*/
udelay(5);
- ipath_set_ib_lstate(dd, INFINIPATH_IBCC_LINKINITCMD_DISABLE <<
- INFINIPATH_IBCC_LINKINITCMD_SHIFT);
+ dd->ipath_f_setextled(dd, 0, 0); /* make sure LEDs are off */
+
+ ipath_set_ib_lstate(dd, 0, INFINIPATH_IBCC_LINKINITCMD_DISABLE);
ipath_cancel_sends(dd, 0);
+ /*
+ * we are shutting down, so tell components that care. We don't do
+ * this on just a link state change, much like ethernet, a cable
+ * unplug, etc. doesn't change driver state
+ */
signal_ib_event(dd, IB_EVENT_PORT_ERR);
/* disable IBC */
*/
dd->ipath_f_quiet_serdes(dd);
+ /* stop all the timers that might still be running */
+ del_timer_sync(&dd->ipath_hol_timer);
if (dd->ipath_stats_timer_active) {
del_timer_sync(&dd->ipath_stats_timer);
dd->ipath_stats_timer_active = 0;
}
+ if (dd->ipath_intrchk_timer.data) {
+ del_timer_sync(&dd->ipath_intrchk_timer);
+ dd->ipath_intrchk_timer.data = 0;
+ }
+ if (atomic_read(&dd->ipath_led_override_timer_active)) {
+ del_timer_sync(&dd->ipath_led_override_timer);
+ atomic_set(&dd->ipath_led_override_timer_active, 0);
+ }
/*
* clear all interrupts and errors, so that the next time the driver
ipath_cdbg(VERBOSE, "free closed port %d "
"ipath_port0_skbinfo @ %p\n", pd->port_port,
skbinfo);
- for (e = 0; e < dd->ipath_rcvegrcnt; e++)
- if (skbinfo[e].skb) {
- pci_unmap_single(dd->pcidev, skbinfo[e].phys,
- dd->ipath_ibmaxlen,
- PCI_DMA_FROMDEVICE);
- dev_kfree_skb(skbinfo[e].skb);
- }
+ for (e = 0; e < dd->ipath_p0_rcvegrcnt; e++)
+ if (skbinfo[e].skb) {
+ pci_unmap_single(dd->pcidev, skbinfo[e].phys,
+ dd->ipath_ibmaxlen,
+ PCI_DMA_FROMDEVICE);
+ dev_kfree_skb(skbinfo[e].skb);
+ }
vfree(skbinfo);
}
kfree(pd->port_tid_pg_list);
*/
idr_init(&unit_table);
if (!idr_pre_get(&unit_table, GFP_KERNEL)) {
+ printk(KERN_ERR IPATH_DRV_NAME ": idr_pre_get() failed\n");
ret = -ENOMEM;
goto bail;
}
goto bail_unit;
}
- ret = ipath_driver_create_group(&ipath_driver.driver);
- if (ret < 0) {
- printk(KERN_ERR IPATH_DRV_NAME ": Unable to create driver "
- "sysfs entries: error %d\n", -ret);
- goto bail_pci;
- }
-
ret = ipath_init_ipathfs();
if (ret < 0) {
printk(KERN_ERR IPATH_DRV_NAME ": Unable to create "
"ipathfs: error %d\n", -ret);
- goto bail_group;
+ goto bail_pci;
}
goto bail;
-bail_group:
- ipath_driver_remove_group(&ipath_driver.driver);
-
bail_pci:
pci_unregister_driver(&ipath_driver);
{
ipath_exit_ipathfs();
- ipath_driver_remove_group(&ipath_driver.driver);
-
ipath_cdbg(VERBOSE, "Unregistering pci driver\n");
pci_unregister_driver(&ipath_driver);
{
int ret, i;
struct ipath_devdata *dd = ipath_lookup(unit);
+ unsigned long flags;
if (!dd) {
ret = -ENODEV;
goto bail;
}
+ spin_lock_irqsave(&dd->ipath_uctxt_lock, flags);
if (dd->ipath_pd)
for (i = 1; i < dd->ipath_cfgports; i++) {
- if (dd->ipath_pd[i] && dd->ipath_pd[i]->port_cnt) {
- ipath_dbg("unit %u port %d is in use "
- "(PID %u cmd %s), can't reset\n",
- unit, i,
- dd->ipath_pd[i]->port_pid,
- dd->ipath_pd[i]->port_comm);
- ret = -EBUSY;
- goto bail;
- }
+ if (!dd->ipath_pd[i] || !dd->ipath_pd[i]->port_cnt)
+ continue;
+ spin_unlock_irqrestore(&dd->ipath_uctxt_lock, flags);
+ ipath_dbg("unit %u port %d is in use "
+ "(PID %u cmd %s), can't reset\n",
+ unit, i,
+ pid_nr(dd->ipath_pd[i]->port_pid),
+ dd->ipath_pd[i]->port_comm);
+ ret = -EBUSY;
+ goto bail;
}
+ spin_unlock_irqrestore(&dd->ipath_uctxt_lock, flags);
+
+ if (dd->ipath_flags & IPATH_HAS_SEND_DMA)
+ teardown_sdma(dd);
dd->ipath_flags &= ~IPATH_INITTED;
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_intmask, 0ULL);
ret = dd->ipath_f_reset(dd);
- if (ret != 1)
- ipath_dbg("reset was not successful\n");
- ipath_dbg("Trying to reinitialize unit %u after reset attempt\n",
- unit);
- ret = ipath_init_chip(dd, 1);
+ if (ret == 1) {
+ ipath_dbg("Reinitializing unit %u after reset attempt\n",
+ unit);
+ ret = ipath_init_chip(dd, 1);
+ } else
+ ret = -EAGAIN;
if (ret)
ipath_dev_err(dd, "Reinitialize unit %u after "
"reset failed with %d\n", unit, ret);
return ret;
}
+/*
+ * send a signal to all the processes that have the driver open
+ * through the normal interfaces (i.e., everything other than diags
+ * interface). Returns number of signalled processes.
+ */
+static int ipath_signal_procs(struct ipath_devdata *dd, int sig)
+{
+ int i, sub, any = 0;
+ struct pid *pid;
+ unsigned long flags;
+
+ if (!dd->ipath_pd)
+ return 0;
+
+ spin_lock_irqsave(&dd->ipath_uctxt_lock, flags);
+ for (i = 1; i < dd->ipath_cfgports; i++) {
+ if (!dd->ipath_pd[i] || !dd->ipath_pd[i]->port_cnt)
+ continue;
+ pid = dd->ipath_pd[i]->port_pid;
+ if (!pid)
+ continue;
+
+ dev_info(&dd->pcidev->dev, "context %d in use "
+ "(PID %u), sending signal %d\n",
+ i, pid_nr(pid), sig);
+ kill_pid(pid, sig, 1);
+ any++;
+ for (sub = 0; sub < INFINIPATH_MAX_SUBPORT; sub++) {
+ pid = dd->ipath_pd[i]->port_subpid[sub];
+ if (!pid)
+ continue;
+ dev_info(&dd->pcidev->dev, "sub-context "
+ "%d:%d in use (PID %u), sending "
+ "signal %d\n", i, sub, pid_nr(pid), sig);
+ kill_pid(pid, sig, 1);
+ any++;
+ }
+ }
+ spin_unlock_irqrestore(&dd->ipath_uctxt_lock, flags);
+ return any;
+}
+
+static void ipath_hol_signal_down(struct ipath_devdata *dd)
+{
+ if (ipath_signal_procs(dd, SIGSTOP))
+ ipath_dbg("Stopped some processes\n");
+ ipath_cancel_sends(dd, 1);
+}
+
+
+static void ipath_hol_signal_up(struct ipath_devdata *dd)
+{
+ if (ipath_signal_procs(dd, SIGCONT))
+ ipath_dbg("Continued some processes\n");
+}
+
+/*
+ * link is down, stop any users processes, and flush pending sends
+ * to prevent HoL blocking, then start the HoL timer that
+ * periodically continues, then stop procs, so they can detect
+ * link down if they want, and do something about it.
+ * Timer may already be running, so use mod_timer, not add_timer.
+ */
+void ipath_hol_down(struct ipath_devdata *dd)
+{
+ dd->ipath_hol_state = IPATH_HOL_DOWN;
+ ipath_hol_signal_down(dd);
+ dd->ipath_hol_next = IPATH_HOL_DOWNCONT;
+ dd->ipath_hol_timer.expires = jiffies +
+ msecs_to_jiffies(ipath_hol_timeout_ms);
+ mod_timer(&dd->ipath_hol_timer, dd->ipath_hol_timer.expires);
+}
+
+/*
+ * link is up, continue any user processes, and ensure timer
+ * is a nop, if running. Let timer keep running, if set; it
+ * will nop when it sees the link is up
+ */
+void ipath_hol_up(struct ipath_devdata *dd)
+{
+ ipath_hol_signal_up(dd);
+ dd->ipath_hol_state = IPATH_HOL_UP;
+}
+
+/*
+ * toggle the running/not running state of user proceses
+ * to prevent HoL blocking on chip resources, but still allow
+ * user processes to do link down special case handling.
+ * Should only be called via the timer
+ */
+void ipath_hol_event(unsigned long opaque)
+{
+ struct ipath_devdata *dd = (struct ipath_devdata *)opaque;
+
+ if (dd->ipath_hol_next == IPATH_HOL_DOWNSTOP
+ && dd->ipath_hol_state != IPATH_HOL_UP) {
+ dd->ipath_hol_next = IPATH_HOL_DOWNCONT;
+ ipath_dbg("Stopping processes\n");
+ ipath_hol_signal_down(dd);
+ } else { /* may do "extra" if also in ipath_hol_up() */
+ dd->ipath_hol_next = IPATH_HOL_DOWNSTOP;
+ ipath_dbg("Continuing processes\n");
+ ipath_hol_signal_up(dd);
+ }
+ if (dd->ipath_hol_state == IPATH_HOL_UP)
+ ipath_dbg("link's up, don't resched timer\n");
+ else {
+ dd->ipath_hol_timer.expires = jiffies +
+ msecs_to_jiffies(ipath_hol_timeout_ms);
+ mod_timer(&dd->ipath_hol_timer,
+ dd->ipath_hol_timer.expires);
+ }
+}
+
int ipath_set_rx_pol_inv(struct ipath_devdata *dd, u8 new_pol_inv)
{
u64 val;
- if ( new_pol_inv > INFINIPATH_XGXS_RX_POL_MASK ) {
+
+ if (new_pol_inv > INFINIPATH_XGXS_RX_POL_MASK)
return -1;
- }
- if ( dd->ipath_rx_pol_inv != new_pol_inv ) {
+ if (dd->ipath_rx_pol_inv != new_pol_inv) {
dd->ipath_rx_pol_inv = new_pol_inv;
val = ipath_read_kreg64(dd, dd->ipath_kregs->kr_xgxsconfig);
val &= ~(INFINIPATH_XGXS_RX_POL_MASK <<
}
return 0;
}
+
+/*
+ * Disable and enable the armlaunch error. Used for PIO bandwidth testing on
+ * the 7220, which is count-based, rather than trigger-based. Safe for the
+ * driver check, since it's at init. Not completely safe when used for
+ * user-mode checking, since some error checking can be lost, but not
+ * particularly risky, and only has problematic side-effects in the face of
+ * very buggy user code. There is no reference counting, but that's also
+ * fine, given the intended use.
+ */
+void ipath_enable_armlaunch(struct ipath_devdata *dd)
+{
+ dd->ipath_lasterror &= ~INFINIPATH_E_SPIOARMLAUNCH;
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_errorclear,
+ INFINIPATH_E_SPIOARMLAUNCH);
+ dd->ipath_errormask |= INFINIPATH_E_SPIOARMLAUNCH;
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_errormask,
+ dd->ipath_errormask);
+}
+
+void ipath_disable_armlaunch(struct ipath_devdata *dd)
+{
+ /* so don't re-enable if already set */
+ dd->ipath_maskederrs &= ~INFINIPATH_E_SPIOARMLAUNCH;
+ dd->ipath_errormask &= ~INFINIPATH_E_SPIOARMLAUNCH;
+ ipath_write_kreg(dd, dd->ipath_kregs->kr_errormask,
+ dd->ipath_errormask);
+}
+
module_init(infinipath_init);
module_exit(infinipath_cleanup);
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff