-/**
+/*
* drivers/gpio/max7301.c
*
* Copyright (C) 2006 Juergen Beisert, Pengutronix
* Copyright (C) 2008 Guennadi Liakhovetski, Pengutronix
+ * Copyright (C) 2009 Wolfram Sang, Pengutronix
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*
- * The Maxim's MAX7301 device is an SPI driven GPIO expander. There are
- * 28 GPIOs. 8 of them can trigger an interrupt. See datasheet for more
- * details
- * Note:
- * - DIN must be stable at the rising edge of clock.
- * - when writing:
- * - always clock in 16 clocks at once
- * - at DIN: D15 first, D0 last
- * - D0..D7 = databyte, D8..D14 = commandbyte
- * - D15 = low -> write command
- * - when reading
- * - always clock in 16 clocks at once
- * - at DIN: D15 first, D0 last
- * - D0..D7 = dummy, D8..D14 = register address
- * - D15 = high -> read command
- * - raise CS and assert it again
- * - always clock in 16 clocks at once
- * - at DOUT: D15 first, D0 last
- * - D0..D7 contains the data from the first cycle
- *
- * The driver exports a standard gpiochip interface
+ * Check max730x.c for further details.
*/
+#include <linux/module.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/mutex.h>
+#include <linux/slab.h>
#include <linux/spi/spi.h>
#include <linux/spi/max7301.h>
-#include <linux/gpio.h>
-
-#define DRIVER_NAME "max7301"
-
-/*
- * Pin configurations, see MAX7301 datasheet page 6
- */
-#define PIN_CONFIG_MASK 0x03
-#define PIN_CONFIG_IN_PULLUP 0x03
-#define PIN_CONFIG_IN_WO_PULLUP 0x02
-#define PIN_CONFIG_OUT 0x01
-
-#define PIN_NUMBER 28
-
-
-/*
- * Some registers must be read back to modify.
- * To save time we cache them here in memory
- */
-struct max7301 {
- struct mutex lock;
- u8 port_config[8]; /* field 0 is unused */
- u32 out_level; /* cached output levels */
- struct gpio_chip chip;
- struct spi_device *spi;
-};
-/**
- * max7301_write - Write a new register content
- * @spi: The SPI device
- * @reg: Register offset
- * @val: Value to write
- *
- * A write to the MAX7301 means one message with one transfer
- *
- * Returns 0 if successful or a negative value on error
- */
-static int max7301_write(struct spi_device *spi, unsigned int reg, unsigned int val)
+/* A write to the MAX7301 means one message with one transfer */
+static int max7301_spi_write(struct device *dev, unsigned int reg,
+ unsigned int val)
{
+ struct spi_device *spi = to_spi_device(dev);
u16 word = ((reg & 0x7F) << 8) | (val & 0xFF);
+
return spi_write(spi, (const u8 *)&word, sizeof(word));
}
-/**
- * max7301_read - Read back register content
- * @spi: The SPI device
- * @reg: Register offset
- *
- * A read from the MAX7301 means two transfers; here, one message each
- *
- * Returns positive 8 bit value from device if successful or a
- * negative value on error
- */
-static int max7301_read(struct spi_device *spi, unsigned int reg)
+/* A read from the MAX7301 means two transfers; here, one message each */
+
+static int max7301_spi_read(struct device *dev, unsigned int reg)
{
int ret;
u16 word;
+ struct spi_device *spi = to_spi_device(dev);
word = 0x8000 | (reg << 8);
ret = spi_write(spi, (const u8 *)&word, sizeof(word));
return word & 0xff;
}
-static int max7301_direction_input(struct gpio_chip *chip, unsigned offset)
-{
- struct max7301 *ts = container_of(chip, struct max7301, chip);
- u8 *config;
- int ret;
-
- /* First 4 pins are unused in the controller */
- offset += 4;
-
- config = &ts->port_config[offset >> 2];
-
- mutex_lock(&ts->lock);
-
- /* Standard GPIO API doesn't support pull-ups, has to be extended.
- * Hard-coding no pollup for now. */
- *config = (*config & ~(3 << (offset & 3))) | (1 << (offset & 3));
-
- ret = max7301_write(ts->spi, 0x08 + (offset >> 2), *config);
-
- mutex_unlock(&ts->lock);
-
- return ret;
-}
-
-static int __max7301_set(struct max7301 *ts, unsigned offset, int value)
-{
- if (value) {
- ts->out_level |= 1 << offset;
- return max7301_write(ts->spi, 0x20 + offset, 0x01);
- } else {
- ts->out_level &= ~(1 << offset);
- return max7301_write(ts->spi, 0x20 + offset, 0x00);
- }
-}
-
-static int max7301_direction_output(struct gpio_chip *chip, unsigned offset,
- int value)
-{
- struct max7301 *ts = container_of(chip, struct max7301, chip);
- u8 *config;
- int ret;
-
- /* First 4 pins are unused in the controller */
- offset += 4;
-
- config = &ts->port_config[offset >> 2];
-
- mutex_lock(&ts->lock);
-
- *config = (*config & ~(3 << (offset & 3))) | (1 << (offset & 3));
-
- ret = __max7301_set(ts, offset, value);
-
- if (!ret)
- ret = max7301_write(ts->spi, 0x08 + (offset >> 2), *config);
-
- mutex_unlock(&ts->lock);
-
- return ret;
-}
-
-static int max7301_get(struct gpio_chip *chip, unsigned offset)
-{
- struct max7301 *ts = container_of(chip, struct max7301, chip);
- int config, level = -EINVAL;
-
- /* First 4 pins are unused in the controller */
- offset += 4;
-
- mutex_lock(&ts->lock);
-
- config = (ts->port_config[offset >> 2] >> ((offset & 3) * 2)) & 3;
-
- switch (config) {
- case 1:
- /* Output: return cached level */
- level = !!(ts->out_level & (1 << offset));
- break;
- case 2:
- case 3:
- /* Input: read out */
- level = max7301_read(ts->spi, 0x20 + offset) & 0x01;
- }
- mutex_unlock(&ts->lock);
-
- return level;
-}
-
-static void max7301_set(struct gpio_chip *chip, unsigned offset, int value)
-{
- struct max7301 *ts = container_of(chip, struct max7301, chip);
-
- /* First 4 pins are unused in the controller */
- offset += 4;
-
- mutex_lock(&ts->lock);
-
- __max7301_set(ts, offset, value);
-
- mutex_unlock(&ts->lock);
-}
-
static int __devinit max7301_probe(struct spi_device *spi)
{
struct max7301 *ts;
- struct max7301_platform_data *pdata;
- int i, ret;
-
- pdata = spi->dev.platform_data;
- if (!pdata || !pdata->base) {
- dev_dbg(&spi->dev, "incorrect or missing platform data\n");
- return -EINVAL;
- }
+ int ret;
- /*
- * bits_per_word cannot be configured in platform data
- */
+ /* bits_per_word cannot be configured in platform data */
spi->bits_per_word = 16;
-
ret = spi_setup(spi);
if (ret < 0)
return ret;
if (!ts)
return -ENOMEM;
- mutex_init(&ts->lock);
-
- dev_set_drvdata(&spi->dev, ts);
+ ts->read = max7301_spi_read;
+ ts->write = max7301_spi_write;
+ ts->dev = &spi->dev;
- /* Power up the chip and disable IRQ output */
- max7301_write(spi, 0x04, 0x01);
-
- ts->spi = spi;
-
- ts->chip.label = DRIVER_NAME,
-
- ts->chip.direction_input = max7301_direction_input;
- ts->chip.get = max7301_get;
- ts->chip.direction_output = max7301_direction_output;
- ts->chip.set = max7301_set;
-
- ts->chip.base = pdata->base;
- ts->chip.ngpio = PIN_NUMBER;
- ts->chip.can_sleep = 1;
- ts->chip.dev = &spi->dev;
- ts->chip.owner = THIS_MODULE;
-
- /*
- * tristate all pins in hardware and cache the
- * register values for later use.
- */
- for (i = 1; i < 8; i++) {
- int j;
- /* 0xAA means input with internal pullup disabled */
- max7301_write(spi, 0x08 + i, 0xAA);
- ts->port_config[i] = 0xAA;
- for (j = 0; j < 4; j++) {
- int offset = (i - 1) * 4 + j;
- ret = max7301_direction_input(&ts->chip, offset);
- if (ret)
- goto exit_destroy;
- }
- }
-
- ret = gpiochip_add(&ts->chip);
+ ret = __max730x_probe(ts);
if (ret)
- goto exit_destroy;
-
- return ret;
-
-exit_destroy:
- dev_set_drvdata(&spi->dev, NULL);
- mutex_destroy(&ts->lock);
- kfree(ts);
+ kfree(ts);
return ret;
}
static int __devexit max7301_remove(struct spi_device *spi)
{
- struct max7301 *ts;
- int ret;
-
- ts = dev_get_drvdata(&spi->dev);
- if (ts == NULL)
- return -ENODEV;
-
- dev_set_drvdata(&spi->dev, NULL);
-
- /* Power down the chip and disable IRQ output */
- max7301_write(spi, 0x04, 0x00);
-
- ret = gpiochip_remove(&ts->chip);
- if (!ret) {
- mutex_destroy(&ts->lock);
- kfree(ts);
- } else
- dev_err(&spi->dev, "Failed to remove the GPIO controller: %d\n",
- ret);
-
- return ret;
+ return __max730x_remove(&spi->dev);
}
+static const struct spi_device_id max7301_id[] = {
+ { "max7301", 0 },
+ { }
+};
+MODULE_DEVICE_TABLE(spi, max7301_id);
+
static struct spi_driver max7301_driver = {
.driver = {
- .name = DRIVER_NAME,
- .owner = THIS_MODULE,
+ .name = "max7301",
+ .owner = THIS_MODULE,
},
- .probe = max7301_probe,
- .remove = __devexit_p(max7301_remove),
+ .probe = max7301_probe,
+ .remove = __devexit_p(max7301_remove),
+ .id_table = max7301_id,
};
static int __init max7301_init(void)
}
module_exit(max7301_exit);
-MODULE_AUTHOR("Juergen Beisert");
+MODULE_AUTHOR("Juergen Beisert, Wolfram Sang");
MODULE_LICENSE("GPL v2");
-MODULE_DESCRIPTION("MAX7301 SPI based GPIO-Expander");
-MODULE_ALIAS("spi:" DRIVER_NAME);
+MODULE_DESCRIPTION("MAX7301 GPIO-Expander");
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff