#define MAX_DEVICES 12
-#include <linux/config.h>
#include <linux/module.h>
#include <linux/errno.h>
#include <linux/signal.h>
#include <linux/ptrace.h>
#include <linux/ioport.h>
#include <linux/mm.h>
+#include <linux/seq_file.h>
#include <linux/slab.h>
#include <linux/netdevice.h>
#include <linux/vmalloc.h>
#include <linux/termios.h>
#include <linux/workqueue.h>
#include <linux/hdlc.h>
+#include <linux/synclink.h>
-#ifdef CONFIG_HDLC_MODULE
-#define CONFIG_HDLC 1
+#if defined(CONFIG_HDLC) || (defined(CONFIG_HDLC_MODULE) && defined(CONFIG_SYNCLINKMP_MODULE))
+#define SYNCLINK_GENERIC_HDLC 1
+#else
+#define SYNCLINK_GENERIC_HDLC 0
#endif
#define GET_USER(error,value,addr) error = get_user(value,addr)
#include <asm/uaccess.h>
-#include "linux/synclink.h"
-
static MGSL_PARAMS default_params = {
MGSL_MODE_HDLC, /* unsigned long mode */
0, /* unsigned char loopback; */
#define IO_PIN_SHUTDOWN_LIMIT 100
-#define RELEVANT_IFLAG(iflag) (iflag & (IGNBRK|BRKINT|IGNPAR|PARMRK|INPCK))
-
struct _input_signal_events {
int ri_up;
int ri_down;
typedef struct _synclinkmp_info {
void *if_ptr; /* General purpose pointer (used by SPPP) */
int magic;
- int flags;
- int count; /* count of opens */
+ struct tty_port port;
int line;
unsigned short close_delay;
unsigned short closing_wait; /* time to wait before closing */
struct mgsl_icount icount;
- struct tty_struct *tty;
int timeout;
int x_char; /* xon/xoff character */
- int blocked_open; /* # of blocked opens */
u16 read_status_mask1; /* break detection (SR1 indications) */
u16 read_status_mask2; /* parity/framing/overun (SR2 indications) */
unsigned char ignore_status_mask1; /* break detection (SR1 indications) */
int tx_get;
int tx_count;
- wait_queue_head_t open_wait;
- wait_queue_head_t close_wait;
-
wait_queue_head_t status_event_wait_q;
wait_queue_head_t event_wait_q;
struct timer_list tx_timer; /* HDLC transmit timeout timer */
u32 pending_bh;
- int bh_running; /* Protection from multiple */
+ bool bh_running; /* Protection from multiple */
int isr_overflow;
- int bh_requested;
+ bool bh_requested;
int dcd_chkcount; /* check counts to prevent */
int cts_chkcount; /* too many IRQs if a signal */
unsigned char *tmp_rx_buf;
unsigned int tmp_rx_buf_count;
- int rx_enabled;
- int rx_overflow;
+ bool rx_enabled;
+ bool rx_overflow;
- int tx_enabled;
- int tx_active;
+ bool tx_enabled;
+ bool tx_active;
u32 idle_mode;
unsigned char ie0_value;
unsigned int irq_level; /* interrupt level */
unsigned long irq_flags;
- int irq_requested; /* nonzero if IRQ requested */
+ bool irq_requested; /* true if IRQ requested */
MGSL_PARAMS params; /* communications parameters */
unsigned char serial_signals; /* current serial signal states */
- int irq_occurred; /* for diagnostics use */
+ bool irq_occurred; /* for diagnostics use */
unsigned int init_error; /* Initialization startup error */
u32 last_mem_alloc;
unsigned char* sca_base; /* HD64570 SCA Memory address */
u32 phys_sca_base;
u32 sca_offset;
- int sca_base_requested;
+ bool sca_base_requested;
unsigned char* lcr_base; /* local config registers (PCI only) */
u32 phys_lcr_base;
unsigned char* statctrl_base; /* status/control register memory */
u32 phys_statctrl_base;
u32 statctrl_offset;
- int sca_statctrl_requested;
+ bool sca_statctrl_requested;
u32 misc_ctrl_value;
char flag_buf[MAX_ASYNC_BUFFER_SIZE];
char char_buf[MAX_ASYNC_BUFFER_SIZE];
- BOOLEAN drop_rts_on_tx_done;
+ bool drop_rts_on_tx_done;
struct _input_signal_events input_signal_events;
/* SPPP/Cisco HDLC device parts */
int netcount;
- int dosyncppp;
spinlock_t netlock;
-#ifdef CONFIG_HDLC
+#if SYNCLINK_GENERIC_HDLC
struct net_device *netdev;
#endif
* .text section address and breakpoint on module load.
* This is useful for use with gdb and add-symbol-file command.
*/
-static int break_on_load=0;
+static int break_on_load = 0;
/*
* Driver major number, defaults to zero to get auto
* assigned major number. May be forced as module parameter.
*/
-static int ttymajor=0;
+static int ttymajor = 0;
/*
* Array of user specified options for ISA adapters.
*/
static int debug_level = 0;
static int maxframe[MAX_DEVICES] = {0,};
-static int dosyncppp[MAX_DEVICES] = {0,};
module_param(break_on_load, bool, 0);
module_param(ttymajor, int, 0);
module_param(debug_level, int, 0);
module_param_array(maxframe, int, NULL, 0);
-module_param_array(dosyncppp, int, NULL, 0);
static char *driver_name = "SyncLink MultiPort driver";
static char *driver_version = "$Revision: 4.38 $";
static int open(struct tty_struct *tty, struct file * filp);
static void close(struct tty_struct *tty, struct file * filp);
static void hangup(struct tty_struct *tty);
-static void set_termios(struct tty_struct *tty, struct termios *old_termios);
+static void set_termios(struct tty_struct *tty, struct ktermios *old_termios);
static int write(struct tty_struct *tty, const unsigned char *buf, int count);
-static void put_char(struct tty_struct *tty, unsigned char ch);
+static int put_char(struct tty_struct *tty, unsigned char ch);
static void send_xchar(struct tty_struct *tty, char ch);
static void wait_until_sent(struct tty_struct *tty, int timeout);
static int write_room(struct tty_struct *tty);
static void tx_release(struct tty_struct *tty);
static int ioctl(struct tty_struct *tty, struct file *file, unsigned int cmd, unsigned long arg);
-static int read_proc(char *page, char **start, off_t off, int count,int *eof, void *data);
static int chars_in_buffer(struct tty_struct *tty);
static void throttle(struct tty_struct * tty);
static void unthrottle(struct tty_struct * tty);
-static void set_break(struct tty_struct *tty, int break_state);
+static int set_break(struct tty_struct *tty, int break_state);
-#ifdef CONFIG_HDLC
+#if SYNCLINK_GENERIC_HDLC
#define dev_to_port(D) (dev_to_hdlc(D)->priv)
static void hdlcdev_tx_done(SLMP_INFO *info);
static void hdlcdev_rx(SLMP_INFO *info, char *buf, int size);
static int tiocmget(struct tty_struct *tty, struct file *file);
static int tiocmset(struct tty_struct *tty, struct file *file,
unsigned int set, unsigned int clear);
-static void set_break(struct tty_struct *tty, int break_state);
+static int set_break(struct tty_struct *tty, int break_state);
static void add_device(SLMP_INFO *info);
static void device_init(int adapter_num, struct pci_dev *pdev);
static int startup(SLMP_INFO *info);
static int block_til_ready(struct tty_struct *tty, struct file * filp,SLMP_INFO *info);
+static int carrier_raised(struct tty_port *port);
static void shutdown(SLMP_INFO *info);
static void program_hw(SLMP_INFO *info);
static void change_params(SLMP_INFO *info);
-static int init_adapter(SLMP_INFO *info);
-static int register_test(SLMP_INFO *info);
-static int irq_test(SLMP_INFO *info);
-static int loopback_test(SLMP_INFO *info);
+static bool init_adapter(SLMP_INFO *info);
+static bool register_test(SLMP_INFO *info);
+static bool irq_test(SLMP_INFO *info);
+static bool loopback_test(SLMP_INFO *info);
static int adapter_test(SLMP_INFO *info);
-static int memory_test(SLMP_INFO *info);
+static bool memory_test(SLMP_INFO *info);
static void reset_adapter(SLMP_INFO *info);
static void reset_port(SLMP_INFO *info);
static void rx_start(SLMP_INFO *info);
static void rx_reset_buffers(SLMP_INFO *info);
static void rx_free_frame_buffers(SLMP_INFO *info, unsigned int first, unsigned int last);
-static int rx_get_frame(SLMP_INFO *info);
+static bool rx_get_frame(SLMP_INFO *info);
static void tx_start(SLMP_INFO *info);
static void tx_stop(SLMP_INFO *info);
static void set_rate(SLMP_INFO *info, u32 data_rate);
static int bh_action(SLMP_INFO *info);
-static void bh_handler(void* Context);
+static void bh_handler(struct work_struct *work);
static void bh_receive(SLMP_INFO *info);
static void bh_transmit(SLMP_INFO *info);
static void bh_status(SLMP_INFO *info);
return;
ld = tty_ldisc_ref(tty);
if (ld) {
- if (ld->receive_buf)
- ld->receive_buf(tty, data, flags, count);
+ if (ld->ops->receive_buf)
+ ld->ops->receive_buf(tty, data, flags, count);
tty_ldisc_deref(ld);
}
}
}
tty->driver_data = info;
- info->tty = tty;
+ info->port.tty = tty;
if (debug_level >= DEBUG_LEVEL_INFO)
printk("%s(%d):%s open(), old ref count = %d\n",
- __FILE__,__LINE__,tty->driver->name, info->count);
+ __FILE__,__LINE__,tty->driver->name, info->port.count);
/* If port is closing, signal caller to try again */
- if (tty_hung_up_p(filp) || info->flags & ASYNC_CLOSING){
- if (info->flags & ASYNC_CLOSING)
- interruptible_sleep_on(&info->close_wait);
- retval = ((info->flags & ASYNC_HUP_NOTIFY) ?
+ if (tty_hung_up_p(filp) || info->port.flags & ASYNC_CLOSING){
+ if (info->port.flags & ASYNC_CLOSING)
+ interruptible_sleep_on(&info->port.close_wait);
+ retval = ((info->port.flags & ASYNC_HUP_NOTIFY) ?
-EAGAIN : -ERESTARTSYS);
goto cleanup;
}
- info->tty->low_latency = (info->flags & ASYNC_LOW_LATENCY) ? 1 : 0;
+ info->port.tty->low_latency = (info->port.flags & ASYNC_LOW_LATENCY) ? 1 : 0;
spin_lock_irqsave(&info->netlock, flags);
if (info->netcount) {
spin_unlock_irqrestore(&info->netlock, flags);
goto cleanup;
}
- info->count++;
+ info->port.count++;
spin_unlock_irqrestore(&info->netlock, flags);
- if (info->count == 1) {
+ if (info->port.count == 1) {
/* 1st open on this device, init hardware */
retval = startup(info);
if (retval < 0)
cleanup:
if (retval) {
if (tty->count == 1)
- info->tty = NULL; /* tty layer will release tty struct */
- if(info->count)
- info->count--;
+ info->port.tty = NULL; /* tty layer will release tty struct */
+ if(info->port.count)
+ info->port.count--;
}
return retval;
*/
static void close(struct tty_struct *tty, struct file *filp)
{
- SLMP_INFO * info = (SLMP_INFO *)tty->driver_data;
+ SLMP_INFO * info = tty->driver_data;
if (sanity_check(info, tty->name, "close"))
return;
if (debug_level >= DEBUG_LEVEL_INFO)
printk("%s(%d):%s close() entry, count=%d\n",
- __FILE__,__LINE__, info->device_name, info->count);
-
- if (!info->count)
- return;
-
- if (tty_hung_up_p(filp))
- goto cleanup;
+ __FILE__,__LINE__, info->device_name, info->port.count);
- if ((tty->count == 1) && (info->count != 1)) {
- /*
- * tty->count is 1 and the tty structure will be freed.
- * info->count should be one in this case.
- * if it's not, correct it so that the port is shutdown.
- */
- printk("%s(%d):%s close: bad refcount; tty->count is 1, "
- "info->count is %d\n",
- __FILE__,__LINE__, info->device_name, info->count);
- info->count = 1;
- }
-
- info->count--;
-
- /* if at least one open remaining, leave hardware active */
- if (info->count)
+ if (tty_port_close_start(&info->port, tty, filp) == 0)
goto cleanup;
-
- info->flags |= ASYNC_CLOSING;
-
- /* set tty->closing to notify line discipline to
- * only process XON/XOFF characters. Only the N_TTY
- * discipline appears to use this (ppp does not).
- */
- tty->closing = 1;
-
- /* wait for transmit data to clear all layers */
-
- if (info->closing_wait != ASYNC_CLOSING_WAIT_NONE) {
- if (debug_level >= DEBUG_LEVEL_INFO)
- printk("%s(%d):%s close() calling tty_wait_until_sent\n",
- __FILE__,__LINE__, info->device_name );
- tty_wait_until_sent(tty, info->closing_wait);
- }
-
- if (info->flags & ASYNC_INITIALIZED)
+
+ if (info->port.flags & ASYNC_INITIALIZED)
wait_until_sent(tty, info->timeout);
- if (tty->driver->flush_buffer)
- tty->driver->flush_buffer(tty);
-
+ flush_buffer(tty);
tty_ldisc_flush(tty);
-
shutdown(info);
- tty->closing = 0;
- info->tty = NULL;
-
- if (info->blocked_open) {
- if (info->close_delay) {
- msleep_interruptible(jiffies_to_msecs(info->close_delay));
- }
- wake_up_interruptible(&info->open_wait);
- }
-
- info->flags &= ~(ASYNC_NORMAL_ACTIVE|ASYNC_CLOSING);
-
- wake_up_interruptible(&info->close_wait);
-
+ tty_port_close_end(&info->port, tty);
+ info->port.tty = NULL;
cleanup:
if (debug_level >= DEBUG_LEVEL_INFO)
printk("%s(%d):%s close() exit, count=%d\n", __FILE__,__LINE__,
- tty->driver->name, info->count);
+ tty->driver->name, info->port.count);
}
/* Called by tty_hangup() when a hangup is signaled.
*/
static void hangup(struct tty_struct *tty)
{
- SLMP_INFO *info = (SLMP_INFO *)tty->driver_data;
+ SLMP_INFO *info = tty->driver_data;
if (debug_level >= DEBUG_LEVEL_INFO)
printk("%s(%d):%s hangup()\n",
flush_buffer(tty);
shutdown(info);
- info->count = 0;
- info->flags &= ~ASYNC_NORMAL_ACTIVE;
- info->tty = NULL;
+ info->port.count = 0;
+ info->port.flags &= ~ASYNC_NORMAL_ACTIVE;
+ info->port.tty = NULL;
- wake_up_interruptible(&info->open_wait);
+ wake_up_interruptible(&info->port.open_wait);
}
/* Set new termios settings
*/
-static void set_termios(struct tty_struct *tty, struct termios *old_termios)
+static void set_termios(struct tty_struct *tty, struct ktermios *old_termios)
{
- SLMP_INFO *info = (SLMP_INFO *)tty->driver_data;
+ SLMP_INFO *info = tty->driver_data;
unsigned long flags;
if (debug_level >= DEBUG_LEVEL_INFO)
printk("%s(%d):%s set_termios()\n", __FILE__,__LINE__,
tty->driver->name );
- /* just return if nothing has changed */
- if ((tty->termios->c_cflag == old_termios->c_cflag)
- && (RELEVANT_IFLAG(tty->termios->c_iflag)
- == RELEVANT_IFLAG(old_termios->c_iflag)))
- return;
-
change_params(info);
/* Handle transition to B0 status */
const unsigned char *buf, int count)
{
int c, ret = 0;
- SLMP_INFO *info = (SLMP_INFO *)tty->driver_data;
+ SLMP_INFO *info = tty->driver_data;
unsigned long flags;
if (debug_level >= DEBUG_LEVEL_INFO)
if (sanity_check(info, tty->name, "write"))
goto cleanup;
- if (!tty || !info->tx_buf)
+ if (!info->tx_buf)
goto cleanup;
if (info->params.mode == MGSL_MODE_HDLC) {
/* Add a character to the transmit buffer.
*/
-static void put_char(struct tty_struct *tty, unsigned char ch)
+static int put_char(struct tty_struct *tty, unsigned char ch)
{
- SLMP_INFO *info = (SLMP_INFO *)tty->driver_data;
+ SLMP_INFO *info = tty->driver_data;
unsigned long flags;
+ int ret = 0;
if ( debug_level >= DEBUG_LEVEL_INFO ) {
printk( "%s(%d):%s put_char(%d)\n",
}
if (sanity_check(info, tty->name, "put_char"))
- return;
+ return 0;
- if (!tty || !info->tx_buf)
- return;
+ if (!info->tx_buf)
+ return 0;
spin_lock_irqsave(&info->lock,flags);
if (info->tx_put >= info->max_frame_size)
info->tx_put -= info->max_frame_size;
info->tx_count++;
+ ret = 1;
}
}
spin_unlock_irqrestore(&info->lock,flags);
+ return ret;
}
/* Send a high-priority XON/XOFF character
*/
static void send_xchar(struct tty_struct *tty, char ch)
{
- SLMP_INFO *info = (SLMP_INFO *)tty->driver_data;
+ SLMP_INFO *info = tty->driver_data;
unsigned long flags;
if (debug_level >= DEBUG_LEVEL_INFO)
*/
static void wait_until_sent(struct tty_struct *tty, int timeout)
{
- SLMP_INFO * info = (SLMP_INFO *)tty->driver_data;
+ SLMP_INFO * info = tty->driver_data;
unsigned long orig_jiffies, char_time;
if (!info )
if (sanity_check(info, tty->name, "wait_until_sent"))
return;
- if (!(info->flags & ASYNC_INITIALIZED))
+ lock_kernel();
+
+ if (!(info->port.flags & ASYNC_INITIALIZED))
goto exit;
orig_jiffies = jiffies;
}
exit:
+ unlock_kernel();
if (debug_level >= DEBUG_LEVEL_INFO)
printk("%s(%d):%s wait_until_sent() exit\n",
__FILE__,__LINE__, info->device_name );
*/
static int write_room(struct tty_struct *tty)
{
- SLMP_INFO *info = (SLMP_INFO *)tty->driver_data;
+ SLMP_INFO *info = tty->driver_data;
int ret;
if (sanity_check(info, tty->name, "write_room"))
return 0;
+ lock_kernel();
if (info->params.mode == MGSL_MODE_HDLC) {
ret = (info->tx_active) ? 0 : HDLC_MAX_FRAME_SIZE;
} else {
if (ret < 0)
ret = 0;
}
+ unlock_kernel();
if (debug_level >= DEBUG_LEVEL_INFO)
printk("%s(%d):%s write_room()=%d\n",
*/
static void flush_chars(struct tty_struct *tty)
{
- SLMP_INFO *info = (SLMP_INFO *)tty->driver_data;
+ SLMP_INFO *info = tty->driver_data;
unsigned long flags;
if ( debug_level >= DEBUG_LEVEL_INFO )
*/
static void flush_buffer(struct tty_struct *tty)
{
- SLMP_INFO *info = (SLMP_INFO *)tty->driver_data;
+ SLMP_INFO *info = tty->driver_data;
unsigned long flags;
if (debug_level >= DEBUG_LEVEL_INFO)
del_timer(&info->tx_timer);
spin_unlock_irqrestore(&info->lock,flags);
- wake_up_interruptible(&tty->write_wait);
tty_wakeup(tty);
}
*/
static void tx_hold(struct tty_struct *tty)
{
- SLMP_INFO *info = (SLMP_INFO *)tty->driver_data;
+ SLMP_INFO *info = tty->driver_data;
unsigned long flags;
if (sanity_check(info, tty->name, "tx_hold"))
*/
static void tx_release(struct tty_struct *tty)
{
- SLMP_INFO *info = (SLMP_INFO *)tty->driver_data;
+ SLMP_INFO *info = tty->driver_data;
unsigned long flags;
if (sanity_check(info, tty->name, "tx_release"))
*
* Return Value: 0 if success, otherwise error code
*/
-static int ioctl(struct tty_struct *tty, struct file *file,
+static int do_ioctl(struct tty_struct *tty, struct file *file,
unsigned int cmd, unsigned long arg)
{
- SLMP_INFO *info = (SLMP_INFO *)tty->driver_data;
+ SLMP_INFO *info = tty->driver_data;
int error;
struct mgsl_icount cnow; /* kernel counter temps */
struct serial_icounter_struct __user *p_cuser; /* user space */
return 0;
}
+static int ioctl(struct tty_struct *tty, struct file *file,
+ unsigned int cmd, unsigned long arg)
+{
+ int ret;
+ lock_kernel();
+ ret = do_ioctl(tty, file, cmd, arg);
+ unlock_kernel();
+ return ret;
+}
+
/*
* /proc fs routines....
*/
-static inline int line_info(char *buf, SLMP_INFO *info)
+static inline void line_info(struct seq_file *m, SLMP_INFO *info)
{
char stat_buf[30];
- int ret;
unsigned long flags;
- ret = sprintf(buf, "%s: SCABase=%08x Mem=%08X StatusControl=%08x LCR=%08X\n"
+ seq_printf(m, "%s: SCABase=%08x Mem=%08X StatusControl=%08x LCR=%08X\n"
"\tIRQ=%d MaxFrameSize=%u\n",
info->device_name,
info->phys_sca_base,
strcat(stat_buf, "|RI");
if (info->params.mode == MGSL_MODE_HDLC) {
- ret += sprintf(buf+ret, "\tHDLC txok:%d rxok:%d",
+ seq_printf(m, "\tHDLC txok:%d rxok:%d",
info->icount.txok, info->icount.rxok);
if (info->icount.txunder)
- ret += sprintf(buf+ret, " txunder:%d", info->icount.txunder);
+ seq_printf(m, " txunder:%d", info->icount.txunder);
if (info->icount.txabort)
- ret += sprintf(buf+ret, " txabort:%d", info->icount.txabort);
+ seq_printf(m, " txabort:%d", info->icount.txabort);
if (info->icount.rxshort)
- ret += sprintf(buf+ret, " rxshort:%d", info->icount.rxshort);
+ seq_printf(m, " rxshort:%d", info->icount.rxshort);
if (info->icount.rxlong)
- ret += sprintf(buf+ret, " rxlong:%d", info->icount.rxlong);
+ seq_printf(m, " rxlong:%d", info->icount.rxlong);
if (info->icount.rxover)
- ret += sprintf(buf+ret, " rxover:%d", info->icount.rxover);
+ seq_printf(m, " rxover:%d", info->icount.rxover);
if (info->icount.rxcrc)
- ret += sprintf(buf+ret, " rxlong:%d", info->icount.rxcrc);
+ seq_printf(m, " rxlong:%d", info->icount.rxcrc);
} else {
- ret += sprintf(buf+ret, "\tASYNC tx:%d rx:%d",
+ seq_printf(m, "\tASYNC tx:%d rx:%d",
info->icount.tx, info->icount.rx);
if (info->icount.frame)
- ret += sprintf(buf+ret, " fe:%d", info->icount.frame);
+ seq_printf(m, " fe:%d", info->icount.frame);
if (info->icount.parity)
- ret += sprintf(buf+ret, " pe:%d", info->icount.parity);
+ seq_printf(m, " pe:%d", info->icount.parity);
if (info->icount.brk)
- ret += sprintf(buf+ret, " brk:%d", info->icount.brk);
+ seq_printf(m, " brk:%d", info->icount.brk);
if (info->icount.overrun)
- ret += sprintf(buf+ret, " oe:%d", info->icount.overrun);
+ seq_printf(m, " oe:%d", info->icount.overrun);
}
/* Append serial signal status to end */
- ret += sprintf(buf+ret, " %s\n", stat_buf+1);
+ seq_printf(m, " %s\n", stat_buf+1);
- ret += sprintf(buf+ret, "\ttxactive=%d bh_req=%d bh_run=%d pending_bh=%x\n",
+ seq_printf(m, "\ttxactive=%d bh_req=%d bh_run=%d pending_bh=%x\n",
info->tx_active,info->bh_requested,info->bh_running,
info->pending_bh);
-
- return ret;
}
/* Called to print information about devices
*/
-int read_proc(char *page, char **start, off_t off, int count,
- int *eof, void *data)
+static int synclinkmp_proc_show(struct seq_file *m, void *v)
{
- int len = 0, l;
- off_t begin = 0;
SLMP_INFO *info;
- len += sprintf(page, "synclinkmp driver:%s\n", driver_version);
+ seq_printf(m, "synclinkmp driver:%s\n", driver_version);
info = synclinkmp_device_list;
while( info ) {
- l = line_info(page + len, info);
- len += l;
- if (len+begin > off+count)
- goto done;
- if (len+begin < off) {
- begin += len;
- len = 0;
- }
+ line_info(m, info);
info = info->next_device;
}
+ return 0;
+}
- *eof = 1;
-done:
- if (off >= len+begin)
- return 0;
- *start = page + (off-begin);
- return ((count < begin+len-off) ? count : begin+len-off);
+static int synclinkmp_proc_open(struct inode *inode, struct file *file)
+{
+ return single_open(file, synclinkmp_proc_show, NULL);
}
+static const struct file_operations synclinkmp_proc_fops = {
+ .owner = THIS_MODULE,
+ .open = synclinkmp_proc_open,
+ .read = seq_read,
+ .llseek = seq_lseek,
+ .release = single_release,
+};
+
/* Return the count of bytes in transmit buffer
*/
static int chars_in_buffer(struct tty_struct *tty)
{
- SLMP_INFO *info = (SLMP_INFO *)tty->driver_data;
+ SLMP_INFO *info = tty->driver_data;
if (sanity_check(info, tty->name, "chars_in_buffer"))
return 0;
*/
static void throttle(struct tty_struct * tty)
{
- SLMP_INFO *info = (SLMP_INFO *)tty->driver_data;
+ SLMP_INFO *info = tty->driver_data;
unsigned long flags;
if (debug_level >= DEBUG_LEVEL_INFO)
*/
static void unthrottle(struct tty_struct * tty)
{
- SLMP_INFO *info = (SLMP_INFO *)tty->driver_data;
+ SLMP_INFO *info = tty->driver_data;
unsigned long flags;
if (debug_level >= DEBUG_LEVEL_INFO)
/* set or clear transmit break condition
* break_state -1=set break condition, 0=clear
*/
-static void set_break(struct tty_struct *tty, int break_state)
+static int set_break(struct tty_struct *tty, int break_state)
{
unsigned char RegValue;
- SLMP_INFO * info = (SLMP_INFO *)tty->driver_data;
+ SLMP_INFO * info = tty->driver_data;
unsigned long flags;
if (debug_level >= DEBUG_LEVEL_INFO)
__FILE__,__LINE__, info->device_name, break_state);
if (sanity_check(info, tty->name, "set_break"))
- return;
+ return -EINVAL;
spin_lock_irqsave(&info->lock,flags);
RegValue = read_reg(info, CTL);
RegValue &= ~BIT3;
write_reg(info, CTL, RegValue);
spin_unlock_irqrestore(&info->lock,flags);
+ return 0;
}
-#ifdef CONFIG_HDLC
+#if SYNCLINK_GENERIC_HDLC
/**
* called by generic HDLC layer when protocol selected (PPP, frame relay, etc.)
unsigned short new_crctype;
/* return error if TTY interface open */
- if (info->count)
+ if (info->port.count)
return -EBUSY;
switch (encoding)
}
info->params.encoding = new_encoding;
- info->params.crc_type = new_crctype;;
+ info->params.crc_type = new_crctype;
/* if network interface up, reprogram hardware */
if (info->netcount)
static int hdlcdev_xmit(struct sk_buff *skb, struct net_device *dev)
{
SLMP_INFO *info = dev_to_port(dev);
- struct net_device_stats *stats = hdlc_stats(dev);
unsigned long flags;
if (debug_level >= DEBUG_LEVEL_INFO)
tx_load_dma_buffer(info, skb->data, skb->len);
/* update network statistics */
- stats->tx_packets++;
- stats->tx_bytes += skb->len;
+ dev->stats.tx_packets++;
+ dev->stats.tx_bytes += skb->len;
/* done with socket buffer, so free it */
dev_kfree_skb(skb);
/* arbitrate between network and tty opens */
spin_lock_irqsave(&info->netlock, flags);
- if (info->count != 0 || info->netcount != 0) {
+ if (info->port.count != 0 || info->netcount != 0) {
printk(KERN_WARNING "%s: hdlc_open returning busy\n", dev->name);
spin_unlock_irqrestore(&info->netlock, flags);
return -EBUSY;
spin_lock_irqsave(&info->lock, flags);
get_signals(info);
spin_unlock_irqrestore(&info->lock, flags);
- hdlc_set_carrier(info->serial_signals & SerialSignal_DCD, dev);
-
+ if (info->serial_signals & SerialSignal_DCD)
+ netif_carrier_on(dev);
+ else
+ netif_carrier_off(dev);
return 0;
}
printk("%s:hdlcdev_ioctl(%s)\n",__FILE__,dev->name);
/* return error if TTY interface open */
- if (info->count)
+ if (info->port.count)
return -EBUSY;
if (cmd != SIOCWANDEV)
static void hdlcdev_tx_timeout(struct net_device *dev)
{
SLMP_INFO *info = dev_to_port(dev);
- struct net_device_stats *stats = hdlc_stats(dev);
unsigned long flags;
if (debug_level >= DEBUG_LEVEL_INFO)
printk("hdlcdev_tx_timeout(%s)\n",dev->name);
- stats->tx_errors++;
- stats->tx_aborted_errors++;
+ dev->stats.tx_errors++;
+ dev->stats.tx_aborted_errors++;
spin_lock_irqsave(&info->lock,flags);
tx_stop(info);
{
struct sk_buff *skb = dev_alloc_skb(size);
struct net_device *dev = info->netdev;
- struct net_device_stats *stats = hdlc_stats(dev);
if (debug_level >= DEBUG_LEVEL_INFO)
printk("hdlcdev_rx(%s)\n",dev->name);
if (skb == NULL) {
- printk(KERN_NOTICE "%s: can't alloc skb, dropping packet\n", dev->name);
- stats->rx_dropped++;
+ printk(KERN_NOTICE "%s: can't alloc skb, dropping packet\n",
+ dev->name);
+ dev->stats.rx_dropped++;
return;
}
- memcpy(skb_put(skb, size),buf,size);
+ memcpy(skb_put(skb, size), buf, size);
- skb->protocol = hdlc_type_trans(skb, info->netdev);
+ skb->protocol = hdlc_type_trans(skb, dev);
- stats->rx_packets++;
- stats->rx_bytes += size;
+ dev->stats.rx_packets++;
+ dev->stats.rx_bytes += size;
netif_rx(skb);
-
- info->netdev->last_rx = jiffies;
}
+static const struct net_device_ops hdlcdev_ops = {
+ .ndo_open = hdlcdev_open,
+ .ndo_stop = hdlcdev_close,
+ .ndo_change_mtu = hdlc_change_mtu,
+ .ndo_start_xmit = hdlc_start_xmit,
+ .ndo_do_ioctl = hdlcdev_ioctl,
+ .ndo_tx_timeout = hdlcdev_tx_timeout,
+};
+
/**
* called by device driver when adding device instance
* do generic HDLC initialization
dev->irq = info->irq_level;
/* network layer callbacks and settings */
- dev->do_ioctl = hdlcdev_ioctl;
- dev->open = hdlcdev_open;
- dev->stop = hdlcdev_close;
- dev->tx_timeout = hdlcdev_tx_timeout;
- dev->watchdog_timeo = 10*HZ;
+ dev->netdev_ops = &hdlcdev_ops;
+ dev->watchdog_timeo = 10 * HZ;
dev->tx_queue_len = 50;
/* generic HDLC layer callbacks and settings */
/* Return next bottom half action to perform.
* Return Value: BH action code or 0 if nothing to do.
*/
-int bh_action(SLMP_INFO *info)
+static int bh_action(SLMP_INFO *info)
{
unsigned long flags;
int rc = 0;
if (!rc) {
/* Mark BH routine as complete */
- info->bh_running = 0;
- info->bh_requested = 0;
+ info->bh_running = false;
+ info->bh_requested = false;
}
spin_unlock_irqrestore(&info->lock,flags);
/* Perform bottom half processing of work items queued by ISR.
*/
-void bh_handler(void* Context)
+static void bh_handler(struct work_struct *work)
{
- SLMP_INFO *info = (SLMP_INFO*)Context;
+ SLMP_INFO *info = container_of(work, SLMP_INFO, task);
int action;
if (!info)
printk( "%s(%d):%s bh_handler() entry\n",
__FILE__,__LINE__,info->device_name);
- info->bh_running = 1;
+ info->bh_running = true;
while((action = bh_action(info)) != 0) {
__FILE__,__LINE__,info->device_name);
}
-void bh_receive(SLMP_INFO *info)
+static void bh_receive(SLMP_INFO *info)
{
if ( debug_level >= DEBUG_LEVEL_BH )
printk( "%s(%d):%s bh_receive()\n",
while( rx_get_frame(info) );
}
-void bh_transmit(SLMP_INFO *info)
+static void bh_transmit(SLMP_INFO *info)
{
- struct tty_struct *tty = info->tty;
+ struct tty_struct *tty = info->port.tty;
if ( debug_level >= DEBUG_LEVEL_BH )
printk( "%s(%d):%s bh_transmit() entry\n",
__FILE__,__LINE__,info->device_name);
- if (tty) {
+ if (tty)
tty_wakeup(tty);
- wake_up_interruptible(&tty->write_wait);
- }
}
-void bh_status(SLMP_INFO *info)
+static void bh_status(SLMP_INFO *info)
{
if ( debug_level >= DEBUG_LEVEL_BH )
printk( "%s(%d):%s bh_status() entry\n",
info->cts_chkcount = 0;
}
-void isr_timer(SLMP_INFO * info)
+static void isr_timer(SLMP_INFO * info)
{
unsigned char timer = (info->port_num & 1) ? TIMER2 : TIMER0;
*/
write_reg(info, (unsigned char)(timer + TMCS), 0);
- info->irq_occurred = TRUE;
+ info->irq_occurred = true;
if ( debug_level >= DEBUG_LEVEL_ISR )
printk("%s(%d):%s isr_timer()\n",
__FILE__,__LINE__,info->device_name);
}
-void isr_rxint(SLMP_INFO * info)
+static void isr_rxint(SLMP_INFO * info)
{
- struct tty_struct *tty = info->tty;
+ struct tty_struct *tty = info->port.tty;
struct mgsl_icount *icount = &info->icount;
unsigned char status = read_reg(info, SR1) & info->ie1_value & (FLGD + IDLD + CDCD + BRKD);
unsigned char status2 = read_reg(info, SR2) & info->ie2_value & OVRN;
if ( tty ) {
if (!(status & info->ignore_status_mask1)) {
if (info->read_status_mask1 & BRKD) {
- *tty->flip.flag_buf_ptr = TTY_BREAK;
- if (info->flags & ASYNC_SAK)
+ tty_insert_flip_char(tty, 0, TTY_BREAK);
+ if (info->port.flags & ASYNC_SAK)
do_SAK(tty);
}
}
/*
* handle async rx data interrupts
*/
-void isr_rxrdy(SLMP_INFO * info)
+static void isr_rxrdy(SLMP_INFO * info)
{
u16 status;
unsigned char DataByte;
- struct tty_struct *tty = info->tty;
+ struct tty_struct *tty = info->port.tty;
struct mgsl_icount *icount = &info->icount;
if ( debug_level >= DEBUG_LEVEL_ISR )
while((status = read_reg(info,CST0)) & BIT0)
{
+ int flag = 0;
+ bool over = false;
DataByte = read_reg(info,TRB);
- if ( tty ) {
- if (tty->flip.count >= TTY_FLIPBUF_SIZE)
- continue;
-
- *tty->flip.char_buf_ptr = DataByte;
- *tty->flip.flag_buf_ptr = 0;
- }
-
icount->rx++;
if ( status & (PE + FRME + OVRN) ) {
if ( tty ) {
if (status & PE)
- *tty->flip.flag_buf_ptr = TTY_PARITY;
+ flag = TTY_PARITY;
else if (status & FRME)
- *tty->flip.flag_buf_ptr = TTY_FRAME;
+ flag = TTY_FRAME;
if (status & OVRN) {
/* Overrun is special, since it's
* reported immediately, and doesn't
* affect the current character
*/
- if (tty->flip.count < TTY_FLIPBUF_SIZE) {
- tty->flip.count++;
- tty->flip.flag_buf_ptr++;
- tty->flip.char_buf_ptr++;
- *tty->flip.flag_buf_ptr = TTY_OVERRUN;
- }
+ over = true;
}
}
} /* end of if (error) */
if ( tty ) {
- tty->flip.flag_buf_ptr++;
- tty->flip.char_buf_ptr++;
- tty->flip.count++;
+ tty_insert_flip_char(tty, DataByte, flag);
+ if (over)
+ tty_insert_flip_char(tty, 0, TTY_OVERRUN);
}
}
if ( debug_level >= DEBUG_LEVEL_ISR ) {
- printk("%s(%d):%s isr_rxrdy() flip count=%d\n",
- __FILE__,__LINE__,info->device_name,
- tty ? tty->flip.count : 0);
printk("%s(%d):%s rx=%d brk=%d parity=%d frame=%d overrun=%d\n",
__FILE__,__LINE__,info->device_name,
icount->rx,icount->brk,icount->parity,
icount->frame,icount->overrun);
}
- if ( tty && tty->flip.count )
+ if ( tty )
tty_flip_buffer_push(tty);
}
info->icount.txok++;
}
- info->tx_active = 0;
+ info->tx_active = false;
info->tx_count = info->tx_put = info->tx_get = 0;
del_timer(&info->tx_timer);
if (info->params.mode != MGSL_MODE_ASYNC && info->drop_rts_on_tx_done ) {
info->serial_signals &= ~SerialSignal_RTS;
- info->drop_rts_on_tx_done = 0;
+ info->drop_rts_on_tx_done = false;
set_signals(info);
}
-#ifdef CONFIG_HDLC
+#if SYNCLINK_GENERIC_HDLC
if (info->netcount)
hdlcdev_tx_done(info);
else
#endif
{
- if (info->tty && (info->tty->stopped || info->tty->hw_stopped)) {
+ if (info->port.tty && (info->port.tty->stopped || info->port.tty->hw_stopped)) {
tx_stop(info);
return;
}
/*
* handle tx status interrupts
*/
-void isr_txint(SLMP_INFO * info)
+static void isr_txint(SLMP_INFO * info)
{
unsigned char status = read_reg(info, SR1) & info->ie1_value & (UDRN + IDLE + CCTS);
/*
* handle async tx data interrupts
*/
-void isr_txrdy(SLMP_INFO * info)
+static void isr_txrdy(SLMP_INFO * info)
{
if ( debug_level >= DEBUG_LEVEL_ISR )
printk("%s(%d):%s isr_txrdy() tx_count=%d\n",
return;
}
- if (info->tty && (info->tty->stopped || info->tty->hw_stopped)) {
+ if (info->port.tty && (info->port.tty->stopped || info->port.tty->hw_stopped)) {
tx_stop(info);
return;
}
if ( info->tx_count )
tx_load_fifo( info );
else {
- info->tx_active = 0;
+ info->tx_active = false;
info->ie0_value &= ~TXRDYE;
write_reg(info, IE0, info->ie0_value);
}
info->pending_bh |= BH_TRANSMIT;
}
-void isr_rxdmaok(SLMP_INFO * info)
+static void isr_rxdmaok(SLMP_INFO * info)
{
/* BIT7 = EOT (end of transfer)
* BIT6 = EOM (end of message/frame)
info->pending_bh |= BH_RECEIVE;
}
-void isr_rxdmaerror(SLMP_INFO * info)
+static void isr_rxdmaerror(SLMP_INFO * info)
{
/* BIT5 = BOF (buffer overflow)
* BIT4 = COF (counter overflow)
printk("%s(%d):%s isr_rxdmaerror(), status=%02x\n",
__FILE__,__LINE__,info->device_name,status);
- info->rx_overflow = TRUE;
+ info->rx_overflow = true;
info->pending_bh |= BH_RECEIVE;
}
-void isr_txdmaok(SLMP_INFO * info)
+static void isr_txdmaok(SLMP_INFO * info)
{
unsigned char status_reg1 = read_reg(info, SR1);
write_reg(info, IE0, info->ie0_value);
}
-void isr_txdmaerror(SLMP_INFO * info)
+static void isr_txdmaerror(SLMP_INFO * info)
{
/* BIT5 = BOF (buffer overflow)
* BIT4 = COF (counter overflow)
/* handle input serial signal changes
*/
-void isr_io_pin( SLMP_INFO *info, u16 status )
+static void isr_io_pin( SLMP_INFO *info, u16 status )
{
struct mgsl_icount *icount;
info->input_signal_events.dcd_up++;
} else
info->input_signal_events.dcd_down++;
-#ifdef CONFIG_HDLC
- if (info->netcount)
- hdlc_set_carrier(status & SerialSignal_DCD, info->netdev);
+#if SYNCLINK_GENERIC_HDLC
+ if (info->netcount) {
+ if (status & SerialSignal_DCD)
+ netif_carrier_on(info->netdev);
+ else
+ netif_carrier_off(info->netdev);
+ }
#endif
}
if (status & MISCSTATUS_CTS_LATCHED)
wake_up_interruptible(&info->status_event_wait_q);
wake_up_interruptible(&info->event_wait_q);
- if ( (info->flags & ASYNC_CHECK_CD) &&
+ if ( (info->port.flags & ASYNC_CHECK_CD) &&
(status & MISCSTATUS_DCD_LATCHED) ) {
if ( debug_level >= DEBUG_LEVEL_ISR )
printk("%s CD now %s...", info->device_name,
(status & SerialSignal_DCD) ? "on" : "off");
if (status & SerialSignal_DCD)
- wake_up_interruptible(&info->open_wait);
+ wake_up_interruptible(&info->port.open_wait);
else {
if ( debug_level >= DEBUG_LEVEL_ISR )
printk("doing serial hangup...");
- if (info->tty)
- tty_hangup(info->tty);
+ if (info->port.tty)
+ tty_hangup(info->port.tty);
}
}
- if ( (info->flags & ASYNC_CTS_FLOW) &&
+ if ( (info->port.flags & ASYNC_CTS_FLOW) &&
(status & MISCSTATUS_CTS_LATCHED) ) {
- if ( info->tty ) {
- if (info->tty->hw_stopped) {
+ if ( info->port.tty ) {
+ if (info->port.tty->hw_stopped) {
if (status & SerialSignal_CTS) {
if ( debug_level >= DEBUG_LEVEL_ISR )
printk("CTS tx start...");
- info->tty->hw_stopped = 0;
+ info->port.tty->hw_stopped = 0;
tx_start(info);
info->pending_bh |= BH_TRANSMIT;
return;
if (!(status & SerialSignal_CTS)) {
if ( debug_level >= DEBUG_LEVEL_ISR )
printk("CTS tx stop...");
- info->tty->hw_stopped = 1;
+ info->port.tty->hw_stopped = 1;
tx_stop(info);
}
}
* dev_id device ID supplied during interrupt registration
* regs interrupted processor context
*/
-static irqreturn_t synclinkmp_interrupt(int irq, void *dev_id,
- struct pt_regs *regs)
+static irqreturn_t synclinkmp_interrupt(int dummy, void *dev_id)
{
- SLMP_INFO * info;
+ SLMP_INFO *info = dev_id;
unsigned char status, status0, status1=0;
unsigned char dmastatus, dmastatus0, dmastatus1=0;
unsigned char timerstatus0, timerstatus1=0;
unsigned short tmp;
if ( debug_level >= DEBUG_LEVEL_ISR )
- printk("%s(%d): synclinkmp_interrupt(%d)entry.\n",
- __FILE__,__LINE__,irq);
-
- info = (SLMP_INFO *)dev_id;
- if (!info)
- return IRQ_NONE;
+ printk(KERN_DEBUG "%s(%d): synclinkmp_interrupt(%d)entry.\n",
+ __FILE__, __LINE__, info->irq_level);
spin_lock(&info->lock);
timerstatus0 = read_reg(info, ISR2);
if ( debug_level >= DEBUG_LEVEL_ISR )
- printk("%s(%d):%s status0=%02x, dmastatus0=%02x, timerstatus0=%02x\n",
- __FILE__,__LINE__,info->device_name,
- status0,dmastatus0,timerstatus0);
+ printk(KERN_DEBUG "%s(%d):%s status0=%02x, dmastatus0=%02x, timerstatus0=%02x\n",
+ __FILE__, __LINE__, info->device_name,
+ status0, dmastatus0, timerstatus0);
if (info->port_count == 4) {
/* get status for SCA1 (ports 2-3) */
* do not request bottom half processing if the
* device is not open in a normal mode.
*/
- if ( port && (port->count || port->netcount) &&
+ if ( port && (port->port.count || port->netcount) &&
port->pending_bh && !port->bh_running &&
!port->bh_requested ) {
if ( debug_level >= DEBUG_LEVEL_ISR )
printk("%s(%d):%s queueing bh task.\n",
__FILE__,__LINE__,port->device_name);
schedule_work(&port->task);
- port->bh_requested = 1;
+ port->bh_requested = true;
}
}
spin_unlock(&info->lock);
if ( debug_level >= DEBUG_LEVEL_ISR )
- printk("%s(%d):synclinkmp_interrupt(%d)exit.\n",
- __FILE__,__LINE__,irq);
+ printk(KERN_DEBUG "%s(%d):synclinkmp_interrupt(%d)exit.\n",
+ __FILE__, __LINE__, info->irq_level);
return IRQ_HANDLED;
}
if ( debug_level >= DEBUG_LEVEL_INFO )
printk("%s(%d):%s tx_releaseup()\n",__FILE__,__LINE__,info->device_name);
- if (info->flags & ASYNC_INITIALIZED)
+ if (info->port.flags & ASYNC_INITIALIZED)
return 0;
if (!info->tx_buf) {
- info->tx_buf = (unsigned char *)kmalloc(info->max_frame_size, GFP_KERNEL);
+ info->tx_buf = kmalloc(info->max_frame_size, GFP_KERNEL);
if (!info->tx_buf) {
printk(KERN_ERR"%s(%d):%s can't allocate transmit buffer\n",
__FILE__,__LINE__,info->device_name);
change_params(info);
- info->status_timer.expires = jiffies + msecs_to_jiffies(10);
- add_timer(&info->status_timer);
+ mod_timer(&info->status_timer, jiffies + msecs_to_jiffies(10));
- if (info->tty)
- clear_bit(TTY_IO_ERROR, &info->tty->flags);
+ if (info->port.tty)
+ clear_bit(TTY_IO_ERROR, &info->port.tty->flags);
- info->flags |= ASYNC_INITIALIZED;
+ info->port.flags |= ASYNC_INITIALIZED;
return 0;
}
{
unsigned long flags;
- if (!(info->flags & ASYNC_INITIALIZED))
+ if (!(info->port.flags & ASYNC_INITIALIZED))
return;
if (debug_level >= DEBUG_LEVEL_INFO)
del_timer(&info->tx_timer);
del_timer(&info->status_timer);
- if (info->tx_buf) {
- kfree(info->tx_buf);
- info->tx_buf = NULL;
- }
+ kfree(info->tx_buf);
+ info->tx_buf = NULL;
spin_lock_irqsave(&info->lock,flags);
reset_port(info);
- if (!info->tty || info->tty->termios->c_cflag & HUPCL) {
+ if (!info->port.tty || info->port.tty->termios->c_cflag & HUPCL) {
info->serial_signals &= ~(SerialSignal_DTR + SerialSignal_RTS);
set_signals(info);
}
spin_unlock_irqrestore(&info->lock,flags);
- if (info->tty)
- set_bit(TTY_IO_ERROR, &info->tty->flags);
+ if (info->port.tty)
+ set_bit(TTY_IO_ERROR, &info->port.tty->flags);
- info->flags &= ~ASYNC_INITIALIZED;
+ info->port.flags &= ~ASYNC_INITIALIZED;
}
static void program_hw(SLMP_INFO *info)
get_signals(info);
- if (info->netcount || (info->tty && info->tty->termios->c_cflag & CREAD) )
+ if (info->netcount || (info->port.tty && info->port.tty->termios->c_cflag & CREAD) )
rx_start(info);
spin_unlock_irqrestore(&info->lock,flags);
unsigned cflag;
int bits_per_char;
- if (!info->tty || !info->tty->termios)
+ if (!info->port.tty || !info->port.tty->termios)
return;
if (debug_level >= DEBUG_LEVEL_INFO)
printk("%s(%d):%s change_params()\n",
__FILE__,__LINE__, info->device_name );
- cflag = info->tty->termios->c_cflag;
+ cflag = info->port.tty->termios->c_cflag;
/* if B0 rate (hangup) specified then negate DTR and RTS */
/* otherwise assert DTR and RTS */
* current data rate.
*/
if (info->params.data_rate <= 460800) {
- info->params.data_rate = tty_get_baud_rate(info->tty);
+ info->params.data_rate = tty_get_baud_rate(info->port.tty);
}
if ( info->params.data_rate ) {
info->timeout += HZ/50; /* Add .02 seconds of slop */
if (cflag & CRTSCTS)
- info->flags |= ASYNC_CTS_FLOW;
+ info->port.flags |= ASYNC_CTS_FLOW;
else
- info->flags &= ~ASYNC_CTS_FLOW;
+ info->port.flags &= ~ASYNC_CTS_FLOW;
if (cflag & CLOCAL)
- info->flags &= ~ASYNC_CHECK_CD;
+ info->port.flags &= ~ASYNC_CHECK_CD;
else
- info->flags |= ASYNC_CHECK_CD;
+ info->port.flags |= ASYNC_CHECK_CD;
/* process tty input control flags */
info->read_status_mask2 = OVRN;
- if (I_INPCK(info->tty))
+ if (I_INPCK(info->port.tty))
info->read_status_mask2 |= PE | FRME;
- if (I_BRKINT(info->tty) || I_PARMRK(info->tty))
+ if (I_BRKINT(info->port.tty) || I_PARMRK(info->port.tty))
info->read_status_mask1 |= BRKD;
- if (I_IGNPAR(info->tty))
+ if (I_IGNPAR(info->port.tty))
info->ignore_status_mask2 |= PE | FRME;
- if (I_IGNBRK(info->tty)) {
+ if (I_IGNBRK(info->port.tty)) {
info->ignore_status_mask1 |= BRKD;
/* If ignoring parity and break indicators, ignore
* overruns too. (For real raw support).
*/
- if (I_IGNPAR(info->tty))
+ if (I_IGNPAR(info->port.tty))
info->ignore_status_mask2 |= OVRN;
}
*/
static int tiocmget(struct tty_struct *tty, struct file *file)
{
- SLMP_INFO *info = (SLMP_INFO *)tty->driver_data;
+ SLMP_INFO *info = tty->driver_data;
unsigned int result;
unsigned long flags;
static int tiocmset(struct tty_struct *tty, struct file *file,
unsigned int set, unsigned int clear)
{
- SLMP_INFO *info = (SLMP_INFO *)tty->driver_data;
+ SLMP_INFO *info = tty->driver_data;
unsigned long flags;
if (debug_level >= DEBUG_LEVEL_INFO)
return 0;
}
+static int carrier_raised(struct tty_port *port)
+{
+ SLMP_INFO *info = container_of(port, SLMP_INFO, port);
+ unsigned long flags;
+ spin_lock_irqsave(&info->lock,flags);
+ get_signals(info);
+ spin_unlock_irqrestore(&info->lock,flags);
+
+ return (info->serial_signals & SerialSignal_DCD) ? 1 : 0;
+}
+
+static void raise_dtr_rts(struct tty_port *port)
+{
+ SLMP_INFO *info = container_of(port, SLMP_INFO, port);
+ unsigned long flags;
+
+ spin_lock_irqsave(&info->lock,flags);
+ info->serial_signals |= SerialSignal_RTS + SerialSignal_DTR;
+ set_signals(info);
+ spin_unlock_irqrestore(&info->lock,flags);
+}
/* Block the current process until the specified port is ready to open.
*/
{
DECLARE_WAITQUEUE(wait, current);
int retval;
- int do_clocal = 0, extra_count = 0;
+ bool do_clocal = false;
+ bool extra_count = false;
unsigned long flags;
+ int cd;
+ struct tty_port *port = &info->port;
if (debug_level >= DEBUG_LEVEL_INFO)
printk("%s(%d):%s block_til_ready()\n",
if (filp->f_flags & O_NONBLOCK || tty->flags & (1 << TTY_IO_ERROR)){
/* nonblock mode is set or port is not enabled */
/* just verify that callout device is not active */
- info->flags |= ASYNC_NORMAL_ACTIVE;
+ port->flags |= ASYNC_NORMAL_ACTIVE;
return 0;
}
if (tty->termios->c_cflag & CLOCAL)
- do_clocal = 1;
+ do_clocal = true;
/* Wait for carrier detect and the line to become
* free (i.e., not in use by the callout). While we are in
- * this loop, info->count is dropped by one, so that
+ * this loop, port->count is dropped by one, so that
* close() knows when to free things. We restore it upon
* exit, either normal or abnormal.
*/
retval = 0;
- add_wait_queue(&info->open_wait, &wait);
+ add_wait_queue(&port->open_wait, &wait);
if (debug_level >= DEBUG_LEVEL_INFO)
printk("%s(%d):%s block_til_ready() before block, count=%d\n",
- __FILE__,__LINE__, tty->driver->name, info->count );
+ __FILE__,__LINE__, tty->driver->name, port->count );
spin_lock_irqsave(&info->lock, flags);
if (!tty_hung_up_p(filp)) {
- extra_count = 1;
- info->count--;
+ extra_count = true;
+ port->count--;
}
spin_unlock_irqrestore(&info->lock, flags);
- info->blocked_open++;
+ port->blocked_open++;
while (1) {
- if ((tty->termios->c_cflag & CBAUD)) {
- spin_lock_irqsave(&info->lock,flags);
- info->serial_signals |= SerialSignal_RTS + SerialSignal_DTR;
- set_signals(info);
- spin_unlock_irqrestore(&info->lock,flags);
- }
+ if (tty->termios->c_cflag & CBAUD)
+ tty_port_raise_dtr_rts(port);
set_current_state(TASK_INTERRUPTIBLE);
- if (tty_hung_up_p(filp) || !(info->flags & ASYNC_INITIALIZED)){
- retval = (info->flags & ASYNC_HUP_NOTIFY) ?
+ if (tty_hung_up_p(filp) || !(port->flags & ASYNC_INITIALIZED)){
+ retval = (port->flags & ASYNC_HUP_NOTIFY) ?
-EAGAIN : -ERESTARTSYS;
break;
}
- spin_lock_irqsave(&info->lock,flags);
- get_signals(info);
- spin_unlock_irqrestore(&info->lock,flags);
+ cd = tty_port_carrier_raised(port);
- if (!(info->flags & ASYNC_CLOSING) &&
- (do_clocal || (info->serial_signals & SerialSignal_DCD)) ) {
+ if (!(port->flags & ASYNC_CLOSING) && (do_clocal || cd))
break;
- }
if (signal_pending(current)) {
retval = -ERESTARTSYS;
if (debug_level >= DEBUG_LEVEL_INFO)
printk("%s(%d):%s block_til_ready() count=%d\n",
- __FILE__,__LINE__, tty->driver->name, info->count );
+ __FILE__,__LINE__, tty->driver->name, port->count );
schedule();
}
set_current_state(TASK_RUNNING);
- remove_wait_queue(&info->open_wait, &wait);
+ remove_wait_queue(&port->open_wait, &wait);
if (extra_count)
- info->count++;
- info->blocked_open--;
+ port->count++;
+ port->blocked_open--;
if (debug_level >= DEBUG_LEVEL_INFO)
printk("%s(%d):%s block_til_ready() after, count=%d\n",
- __FILE__,__LINE__, tty->driver->name, info->count );
+ __FILE__,__LINE__, tty->driver->name, port->count );
if (!retval)
- info->flags |= ASYNC_NORMAL_ACTIVE;
+ port->flags |= ASYNC_NORMAL_ACTIVE;
return retval;
}
-int alloc_dma_bufs(SLMP_INFO *info)
+static int alloc_dma_bufs(SLMP_INFO *info)
{
unsigned short BuffersPerFrame;
unsigned short BufferCount;
/* Allocate DMA buffers for the transmit and receive descriptor lists.
*/
-int alloc_buf_list(SLMP_INFO *info)
+static int alloc_buf_list(SLMP_INFO *info)
{
unsigned int i;
/* Allocate the frame DMA buffers used by the specified buffer list.
*/
-int alloc_frame_bufs(SLMP_INFO *info, SCADESC *buf_list,SCADESC_EX *buf_list_ex,int count)
+static int alloc_frame_bufs(SLMP_INFO *info, SCADESC *buf_list,SCADESC_EX *buf_list_ex,int count)
{
int i;
unsigned long phys_addr;
return 0;
}
-void free_dma_bufs(SLMP_INFO *info)
+static void free_dma_bufs(SLMP_INFO *info)
{
info->buffer_list = NULL;
info->rx_buf_list = NULL;
/* allocate buffer large enough to hold max_frame_size.
* This buffer is used to pass an assembled frame to the line discipline.
*/
-int alloc_tmp_rx_buf(SLMP_INFO *info)
+static int alloc_tmp_rx_buf(SLMP_INFO *info)
{
info->tmp_rx_buf = kmalloc(info->max_frame_size, GFP_KERNEL);
if (info->tmp_rx_buf == NULL)
return 0;
}
-void free_tmp_rx_buf(SLMP_INFO *info)
+static void free_tmp_rx_buf(SLMP_INFO *info)
{
- if (info->tmp_rx_buf)
- kfree(info->tmp_rx_buf);
+ kfree(info->tmp_rx_buf);
info->tmp_rx_buf = NULL;
}
-int claim_resources(SLMP_INFO *info)
+static int claim_resources(SLMP_INFO *info)
{
if (request_mem_region(info->phys_memory_base,SCA_MEM_SIZE,"synclinkmp") == NULL) {
printk( "%s(%d):%s mem addr conflict, Addr=%08X\n",
goto errout;
}
else
- info->shared_mem_requested = 1;
+ info->shared_mem_requested = true;
if (request_mem_region(info->phys_lcr_base + info->lcr_offset,128,"synclinkmp") == NULL) {
printk( "%s(%d):%s lcr mem addr conflict, Addr=%08X\n",
goto errout;
}
else
- info->lcr_mem_requested = 1;
+ info->lcr_mem_requested = true;
if (request_mem_region(info->phys_sca_base + info->sca_offset,SCA_BASE_SIZE,"synclinkmp") == NULL) {
printk( "%s(%d):%s sca mem addr conflict, Addr=%08X\n",
goto errout;
}
else
- info->sca_base_requested = 1;
+ info->sca_base_requested = true;
if (request_mem_region(info->phys_statctrl_base + info->statctrl_offset,SCA_REG_SIZE,"synclinkmp") == NULL) {
printk( "%s(%d):%s stat/ctrl mem addr conflict, Addr=%08X\n",
goto errout;
}
else
- info->sca_statctrl_requested = 1;
+ info->sca_statctrl_requested = true;
- info->memory_base = ioremap(info->phys_memory_base,SCA_MEM_SIZE);
+ info->memory_base = ioremap_nocache(info->phys_memory_base,
+ SCA_MEM_SIZE);
if (!info->memory_base) {
printk( "%s(%d):%s Cant map shared memory, MemAddr=%08X\n",
__FILE__,__LINE__,info->device_name, info->phys_memory_base );
goto errout;
}
- info->lcr_base = ioremap(info->phys_lcr_base,PAGE_SIZE);
+ info->lcr_base = ioremap_nocache(info->phys_lcr_base, PAGE_SIZE);
if (!info->lcr_base) {
printk( "%s(%d):%s Cant map LCR memory, MemAddr=%08X\n",
__FILE__,__LINE__,info->device_name, info->phys_lcr_base );
}
info->lcr_base += info->lcr_offset;
- info->sca_base = ioremap(info->phys_sca_base,PAGE_SIZE);
+ info->sca_base = ioremap_nocache(info->phys_sca_base, PAGE_SIZE);
if (!info->sca_base) {
printk( "%s(%d):%s Cant map SCA memory, MemAddr=%08X\n",
__FILE__,__LINE__,info->device_name, info->phys_sca_base );
}
info->sca_base += info->sca_offset;
- info->statctrl_base = ioremap(info->phys_statctrl_base,PAGE_SIZE);
+ info->statctrl_base = ioremap_nocache(info->phys_statctrl_base,
+ PAGE_SIZE);
if (!info->statctrl_base) {
printk( "%s(%d):%s Cant map SCA Status/Control memory, MemAddr=%08X\n",
__FILE__,__LINE__,info->device_name, info->phys_statctrl_base );
return -ENODEV;
}
-void release_resources(SLMP_INFO *info)
+static void release_resources(SLMP_INFO *info)
{
if ( debug_level >= DEBUG_LEVEL_INFO )
printk( "%s(%d):%s release_resources() entry\n",
if ( info->irq_requested ) {
free_irq(info->irq_level, info);
- info->irq_requested = 0;
+ info->irq_requested = false;
}
if ( info->shared_mem_requested ) {
release_mem_region(info->phys_memory_base,SCA_MEM_SIZE);
- info->shared_mem_requested = 0;
+ info->shared_mem_requested = false;
}
if ( info->lcr_mem_requested ) {
release_mem_region(info->phys_lcr_base + info->lcr_offset,128);
- info->lcr_mem_requested = 0;
+ info->lcr_mem_requested = false;
}
if ( info->sca_base_requested ) {
release_mem_region(info->phys_sca_base + info->sca_offset,SCA_BASE_SIZE);
- info->sca_base_requested = 0;
+ info->sca_base_requested = false;
}
if ( info->sca_statctrl_requested ) {
release_mem_region(info->phys_statctrl_base + info->statctrl_offset,SCA_REG_SIZE);
- info->sca_statctrl_requested = 0;
+ info->sca_statctrl_requested = false;
}
if (info->memory_base){
/* Add the specified device instance data structure to the
* global linked list of devices and increment the device count.
*/
-void add_device(SLMP_INFO *info)
+static void add_device(SLMP_INFO *info)
{
info->next_device = NULL;
info->line = synclinkmp_device_count;
if (info->line < MAX_DEVICES) {
if (maxframe[info->line])
info->max_frame_size = maxframe[info->line];
- info->dosyncppp = dosyncppp[info->line];
}
synclinkmp_device_count++;
info->irq_level,
info->max_frame_size );
-#ifdef CONFIG_HDLC
+#if SYNCLINK_GENERIC_HDLC
hdlcdev_init(info);
#endif
}
+static const struct tty_port_operations port_ops = {
+ .carrier_raised = carrier_raised,
+ .raise_dtr_rts = raise_dtr_rts,
+};
+
/* Allocate and initialize a device instance structure
*
* Return Value: pointer to SLMP_INFO if success, otherwise NULL
{
SLMP_INFO *info;
- info = (SLMP_INFO *)kmalloc(sizeof(SLMP_INFO),
+ info = kzalloc(sizeof(SLMP_INFO),
GFP_KERNEL);
if (!info) {
printk("%s(%d) Error can't allocate device instance data for adapter %d, port %d\n",
__FILE__,__LINE__, adapter_num, port_num);
} else {
- memset(info, 0, sizeof(SLMP_INFO));
+ tty_port_init(&info->port);
+ info->port.ops = &port_ops;
info->magic = MGSL_MAGIC;
- INIT_WORK(&info->task, bh_handler, info);
+ INIT_WORK(&info->task, bh_handler);
info->max_frame_size = 4096;
- info->close_delay = 5*HZ/10;
- info->closing_wait = 30*HZ;
- init_waitqueue_head(&info->open_wait);
- init_waitqueue_head(&info->close_wait);
+ info->port.close_delay = 5*HZ/10;
+ info->port.closing_wait = 30*HZ;
init_waitqueue_head(&info->status_event_wait_q);
init_waitqueue_head(&info->event_wait_q);
spin_lock_init(&info->netlock);
info->phys_statctrl_base &= ~(PAGE_SIZE-1);
info->bus_type = MGSL_BUS_TYPE_PCI;
- info->irq_flags = SA_SHIRQ;
-
- init_timer(&info->tx_timer);
- info->tx_timer.data = (unsigned long)info;
- info->tx_timer.function = tx_timeout;
+ info->irq_flags = IRQF_SHARED;
- init_timer(&info->status_timer);
- info->status_timer.data = (unsigned long)info;
- info->status_timer.function = status_timeout;
+ setup_timer(&info->tx_timer, tx_timeout, (unsigned long)info);
+ setup_timer(&info->status_timer, status_timeout,
+ (unsigned long)info);
/* Store the PCI9050 misc control register value because a flaw
* in the PCI9050 prevents LCR registers from being read if
return info;
}
-void device_init(int adapter_num, struct pci_dev *pdev)
+static void device_init(int adapter_num, struct pci_dev *pdev)
{
SLMP_INFO *port_array[SCA_MAX_PORTS];
int port;
port_array[0]->irq_level );
}
else {
- port_array[0]->irq_requested = 1;
+ port_array[0]->irq_requested = true;
adapter_test(port_array[0]);
}
}
}
-static struct tty_operations ops = {
+static const struct tty_operations ops = {
.open = open,
.close = close,
.write = write,
.send_xchar = send_xchar,
.break_ctl = set_break,
.wait_until_sent = wait_until_sent,
- .read_proc = read_proc,
.set_termios = set_termios,
.stop = tx_hold,
.start = tx_release,
.hangup = hangup,
.tiocmget = tiocmget,
.tiocmset = tiocmset,
+ .proc_fops = &synclinkmp_proc_fops,
};
+
static void synclinkmp_cleanup(void)
{
int rc;
/* release devices */
info = synclinkmp_device_list;
while(info) {
-#ifdef CONFIG_HDLC
+#if SYNCLINK_GENERIC_HDLC
hdlcdev_exit(info);
#endif
free_dma_bufs(info);
serial_driver->init_termios = tty_std_termios;
serial_driver->init_termios.c_cflag =
B9600 | CS8 | CREAD | HUPCL | CLOCAL;
+ serial_driver->init_termios.c_ispeed = 9600;
+ serial_driver->init_termios.c_ospeed = 9600;
serial_driver->flags = TTY_DRIVER_REAL_RAW;
tty_set_operations(serial_driver, &ops);
if ((rc = tty_register_driver(serial_driver)) < 0) {
* The TxCLK and RxCLK signals are generated from the BRG and
* the TxD is looped back to the RxD internally.
*/
-void enable_loopback(SLMP_INFO *info, int enable)
+static void enable_loopback(SLMP_INFO *info, int enable)
{
if (enable) {
/* MD2 (Mode Register 2)
* data_rate data rate of clock in bits per second
* A data rate of 0 disables the AUX clock.
*/
-void set_rate( SLMP_INFO *info, u32 data_rate )
+static void set_rate( SLMP_INFO *info, u32 data_rate )
{
u32 TMCValue;
unsigned char BRValue;
/* Disable receiver
*/
-void rx_stop(SLMP_INFO *info)
+static void rx_stop(SLMP_INFO *info)
{
if (debug_level >= DEBUG_LEVEL_ISR)
printk("%s(%d):%s rx_stop()\n",
write_reg(info, RXDMA + DCMD, SWABORT); /* reset/init Rx DMA */
write_reg(info, RXDMA + DIR, 0); /* disable Rx DMA interrupts */
- info->rx_enabled = 0;
- info->rx_overflow = 0;
+ info->rx_enabled = false;
+ info->rx_overflow = false;
}
/* enable the receiver
*/
-void rx_start(SLMP_INFO *info)
+static void rx_start(SLMP_INFO *info)
{
int i;
write_reg(info, CMD, RXENABLE);
- info->rx_overflow = FALSE;
- info->rx_enabled = 1;
+ info->rx_overflow = false;
+ info->rx_enabled = true;
}
/* Enable the transmitter and send a transmit frame if
* one is loaded in the DMA buffers.
*/
-void tx_start(SLMP_INFO *info)
+static void tx_start(SLMP_INFO *info)
{
if (debug_level >= DEBUG_LEVEL_ISR)
printk("%s(%d):%s tx_start() tx_count=%d\n",
if (!info->tx_enabled ) {
write_reg(info, CMD, TXRESET);
write_reg(info, CMD, TXENABLE);
- info->tx_enabled = TRUE;
+ info->tx_enabled = true;
}
if ( info->tx_count ) {
/* RTS and set a flag indicating that the driver should */
/* negate RTS when the transmission completes. */
- info->drop_rts_on_tx_done = 0;
+ info->drop_rts_on_tx_done = false;
if (info->params.mode != MGSL_MODE_ASYNC) {
if ( !(info->serial_signals & SerialSignal_RTS) ) {
info->serial_signals |= SerialSignal_RTS;
set_signals( info );
- info->drop_rts_on_tx_done = 1;
+ info->drop_rts_on_tx_done = true;
}
}
write_reg(info, TXDMA + DIR, 0x40); /* enable Tx DMA interrupts (EOM) */
write_reg(info, TXDMA + DSR, 0xf2); /* clear Tx DMA IRQs, enable Tx DMA */
- info->tx_timer.expires = jiffies + msecs_to_jiffies(5000);
- add_timer(&info->tx_timer);
+ mod_timer(&info->tx_timer, jiffies +
+ msecs_to_jiffies(5000));
}
else {
tx_load_fifo(info);
write_reg(info, IE0, info->ie0_value);
}
- info->tx_active = 1;
+ info->tx_active = true;
}
}
/* stop the transmitter and DMA
*/
-void tx_stop( SLMP_INFO *info )
+static void tx_stop( SLMP_INFO *info )
{
if (debug_level >= DEBUG_LEVEL_ISR)
printk("%s(%d):%s tx_stop()\n",
info->ie0_value &= ~TXRDYE;
write_reg(info, IE0, info->ie0_value); /* disable tx data interrupts */
- info->tx_enabled = 0;
- info->tx_active = 0;
+ info->tx_enabled = false;
+ info->tx_active = false;
}
/* Fill the transmit FIFO until the FIFO is full or
* there is no more data to load.
*/
-void tx_load_fifo(SLMP_INFO *info)
+static void tx_load_fifo(SLMP_INFO *info)
{
u8 TwoBytes[2];
/* Reset a port to a known state
*/
-void reset_port(SLMP_INFO *info)
+static void reset_port(SLMP_INFO *info)
{
if (info->sca_base) {
/* Reset all the ports to a known state.
*/
-void reset_adapter(SLMP_INFO *info)
+static void reset_adapter(SLMP_INFO *info)
{
int i;
/* Program port for asynchronous communications.
*/
-void async_mode(SLMP_INFO *info)
+static void async_mode(SLMP_INFO *info)
{
unsigned char RegValue;
/* MD2, Mode Register 2
*
* 07..02 Reserved, must be 0
- * 01..00 CNCT<1..0> Channel connection, 0=normal
+ * 01..00 CNCT<1..0> Channel connection, 00=normal 11=local loopback
*
* 0000 0000
*/
RegValue = 0x00;
+ if (info->params.loopback)
+ RegValue |= (BIT1 + BIT0);
write_reg(info, MD2, RegValue);
/* RXS, Receive clock source
write_reg(info, IE2, info->ie2_value);
set_rate( info, info->params.data_rate * 16 );
-
- if (info->params.loopback)
- enable_loopback(info,1);
}
/* Program the SCA for HDLC communications.
*/
-void hdlc_mode(SLMP_INFO *info)
+static void hdlc_mode(SLMP_INFO *info)
{
unsigned char RegValue;
u32 DpllDivisor;
/* Set the transmit HDLC idle mode
*/
-void tx_set_idle(SLMP_INFO *info)
+static void tx_set_idle(SLMP_INFO *info)
{
unsigned char RegValue = 0xff;
/* Query the adapter for the state of the V24 status (input) signals.
*/
-void get_signals(SLMP_INFO *info)
+static void get_signals(SLMP_INFO *info)
{
u16 status = read_reg(info, SR3);
u16 gpstatus = read_status_reg(info);
/* Set the state of DTR and RTS based on contents of
* serial_signals member of device context.
*/
-void set_signals(SLMP_INFO *info)
+static void set_signals(SLMP_INFO *info)
{
unsigned char RegValue;
u16 EnableBit;
* and set the current buffer to the first buffer. This effectively
* makes all buffers free and discards any data in buffers.
*/
-void rx_reset_buffers(SLMP_INFO *info)
+static void rx_reset_buffers(SLMP_INFO *info)
{
rx_free_frame_buffers(info, 0, info->rx_buf_count - 1);
}
* first index of 1st receive buffer of frame
* last index of last receive buffer of frame
*/
-void rx_free_frame_buffers(SLMP_INFO *info, unsigned int first, unsigned int last)
+static void rx_free_frame_buffers(SLMP_INFO *info, unsigned int first, unsigned int last)
{
- int done = 0;
+ bool done = false;
while(!done) {
/* reset current buffer for reuse */
info->rx_buf_list[first].status = 0xff;
if (first == last) {
- done = 1;
+ done = true;
/* set new last rx descriptor address */
write_reg16(info, RXDMA + EDA, info->rx_buf_list_ex[first].phys_entry);
}
/* Return a received frame from the receive DMA buffers.
* Only frames received without errors are returned.
*
- * Return Value: 1 if frame returned, otherwise 0
+ * Return Value: true if frame returned, otherwise false
*/
-int rx_get_frame(SLMP_INFO *info)
+static bool rx_get_frame(SLMP_INFO *info)
{
unsigned int StartIndex, EndIndex; /* index of 1st and last buffers of Rx frame */
unsigned short status;
unsigned int framesize = 0;
- int ReturnCode = 0;
+ bool ReturnCode = false;
unsigned long flags;
- struct tty_struct *tty = info->tty;
+ struct tty_struct *tty = info->port.tty;
unsigned char addr_field = 0xff;
SCADESC *desc;
SCADESC_EX *desc_ex;
info->icount.rxcrc++;
framesize = 0;
-#ifdef CONFIG_HDLC
+#if SYNCLINK_GENERIC_HDLC
{
- struct net_device_stats *stats = hdlc_stats(info->netdev);
- stats->rx_errors++;
- stats->rx_frame_errors++;
+ info->netdev->stats.rx_errors++;
+ info->netdev->stats.rx_frame_errors++;
}
#endif
}
index = 0;
}
-#ifdef CONFIG_HDLC
+#if SYNCLINK_GENERIC_HDLC
if (info->netcount)
hdlcdev_rx(info,info->tmp_rx_buf,framesize);
else
/* Free the buffers used by this frame. */
rx_free_frame_buffers( info, StartIndex, EndIndex );
- ReturnCode = 1;
+ ReturnCode = true;
Cleanup:
if ( info->rx_enabled && info->rx_overflow ) {
/* load the transmit DMA buffer with data
*/
-void tx_load_dma_buffer(SLMP_INFO *info, const char *buf, unsigned int count)
+static void tx_load_dma_buffer(SLMP_INFO *info, const char *buf, unsigned int count)
{
unsigned short copy_count;
unsigned int i = 0;
info->last_tx_buf = ++i;
}
-int register_test(SLMP_INFO *info)
+static bool register_test(SLMP_INFO *info)
{
static unsigned char testval[] = {0x00, 0xff, 0xaa, 0x55, 0x69, 0x96};
- static unsigned int count = sizeof(testval)/sizeof(unsigned char);
+ static unsigned int count = ARRAY_SIZE(testval);
unsigned int i;
- int rc = TRUE;
+ bool rc = true;
unsigned long flags;
spin_lock_irqsave(&info->lock,flags);
(read_reg(info, SA0) != testval[(i+2)%count]) ||
(read_reg(info, SA1) != testval[(i+3)%count]) )
{
- rc = FALSE;
+ rc = false;
break;
}
}
return rc;
}
-int irq_test(SLMP_INFO *info)
+static bool irq_test(SLMP_INFO *info)
{
unsigned long timeout;
unsigned long flags;
/* assume failure */
info->init_error = DiagStatus_IrqFailure;
- info->irq_occurred = FALSE;
+ info->irq_occurred = false;
/* setup timer0 on SCA0 to interrupt */
/* initialize individual SCA device (2 ports)
*/
-static int sca_init(SLMP_INFO *info)
+static bool sca_init(SLMP_INFO *info)
{
/* set wait controller to single mem partition (low), no wait states */
write_reg(info, PABR0, 0); /* wait controller addr boundary 0 */
*/
write_reg(info, ITCR, 0);
- return TRUE;
+ return true;
}
/* initialize adapter hardware
*/
-int init_adapter(SLMP_INFO *info)
+static bool init_adapter(SLMP_INFO *info)
{
int i;
sca_init(info->port_array[0]);
sca_init(info->port_array[2]);
- return TRUE;
+ return true;
}
/* Loopback an HDLC frame to test the hardware
* interrupt and DMA functions.
*/
-int loopback_test(SLMP_INFO *info)
+static bool loopback_test(SLMP_INFO *info)
{
#define TESTFRAMESIZE 20
unsigned long timeout;
u16 count = TESTFRAMESIZE;
unsigned char buf[TESTFRAMESIZE];
- int rc = FALSE;
+ bool rc = false;
unsigned long flags;
- struct tty_struct *oldtty = info->tty;
+ struct tty_struct *oldtty = info->port.tty;
u32 speed = info->params.clock_speed;
info->params.clock_speed = 3686400;
- info->tty = NULL;
+ info->port.tty = NULL;
/* assume failure */
info->init_error = DiagStatus_DmaFailure;
msleep_interruptible(10);
if (rx_get_frame(info)) {
- rc = TRUE;
+ rc = true;
break;
}
}
/* verify received frame length and contents */
- if (rc == TRUE &&
- ( info->tmp_rx_buf_count != count ||
- memcmp(buf, info->tmp_rx_buf,count))) {
- rc = FALSE;
+ if (rc &&
+ ( info->tmp_rx_buf_count != count ||
+ memcmp(buf, info->tmp_rx_buf,count))) {
+ rc = false;
}
spin_lock_irqsave(&info->lock,flags);
spin_unlock_irqrestore(&info->lock,flags);
info->params.clock_speed = speed;
- info->tty = oldtty;
+ info->port.tty = oldtty;
return rc;
}
/* Perform diagnostics on hardware
*/
-int adapter_test( SLMP_INFO *info )
+static int adapter_test( SLMP_INFO *info )
{
unsigned long flags;
if ( debug_level >= DEBUG_LEVEL_INFO )
/* Test the shared memory on a PCI adapter.
*/
-int memory_test(SLMP_INFO *info)
+static bool memory_test(SLMP_INFO *info)
{
static unsigned long testval[] = { 0x0, 0x55555555, 0xaaaaaaaa,
0x66666666, 0x99999999, 0xffffffff, 0x12345678 };
- unsigned long count = sizeof(testval)/sizeof(unsigned long);
+ unsigned long count = ARRAY_SIZE(testval);
unsigned long i;
unsigned long limit = SCA_MEM_SIZE/sizeof(unsigned long);
unsigned long * addr = (unsigned long *)info->memory_base;
for ( i = 0 ; i < count ; i++ ) {
*addr = testval[i];
if ( *addr != testval[i] )
- return FALSE;
+ return false;
}
/* Test address lines with incrementing pattern over */
for ( i = 0 ; i < limit ; i++ ) {
if ( *addr != i * 4 )
- return FALSE;
+ return false;
addr++;
}
memset( info->memory_base, 0, SCA_MEM_SIZE );
- return TRUE;
+ return true;
}
/* Load data into PCI adapter shared memory.
* the write transation. This allows any pending DMA request to gain control
* of the local bus in a timely fasion.
*/
-void load_pci_memory(SLMP_INFO *info, char* dest, const char* src, unsigned short count)
+static void load_pci_memory(SLMP_INFO *info, char* dest, const char* src, unsigned short count)
{
/* A load interval of 16 allows for 4 32-bit writes at */
/* 136ns each for a maximum latency of 542ns on the local bus.*/
memcpy(dest, src, count % sca_pci_load_interval);
}
-void trace_block(SLMP_INFO *info,const char* data, int count, int xmit)
+static void trace_block(SLMP_INFO *info,const char* data, int count, int xmit)
{
int i;
int linecount;
/* called when HDLC frame times out
* update stats and do tx completion processing
*/
-void tx_timeout(unsigned long context)
+static void tx_timeout(unsigned long context)
{
SLMP_INFO *info = (SLMP_INFO*)context;
unsigned long flags;
info->icount.txtimeout++;
}
spin_lock_irqsave(&info->lock,flags);
- info->tx_active = 0;
+ info->tx_active = false;
info->tx_count = info->tx_put = info->tx_get = 0;
spin_unlock_irqrestore(&info->lock,flags);
-#ifdef CONFIG_HDLC
+#if SYNCLINK_GENERIC_HDLC
if (info->netcount)
hdlcdev_tx_done(info);
else
/* called to periodically check the DSR/RI modem signal input status
*/
-void status_timeout(unsigned long context)
+static void status_timeout(unsigned long context)
{
u16 status = 0;
SLMP_INFO *info = (SLMP_INFO*)context;
if (status)
isr_io_pin(info,status);
- info->status_timer.data = (unsigned long)info;
- info->status_timer.function = status_timeout;
- info->status_timer.expires = jiffies + msecs_to_jiffies(10);
- add_timer(&info->status_timer);
+ mod_timer(&info->status_timer, jiffies + msecs_to_jiffies(10));
}
}
-unsigned char read_reg(SLMP_INFO * info, unsigned char Addr)
+static unsigned char read_reg(SLMP_INFO * info, unsigned char Addr)
{
CALC_REGADDR();
return *RegAddr;
}
-void write_reg(SLMP_INFO * info, unsigned char Addr, unsigned char Value)
+static void write_reg(SLMP_INFO * info, unsigned char Addr, unsigned char Value)
{
CALC_REGADDR();
*RegAddr = Value;
}
-u16 read_reg16(SLMP_INFO * info, unsigned char Addr)
+static u16 read_reg16(SLMP_INFO * info, unsigned char Addr)
{
CALC_REGADDR();
return *((u16 *)RegAddr);
}
-void write_reg16(SLMP_INFO * info, unsigned char Addr, u16 Value)
+static void write_reg16(SLMP_INFO * info, unsigned char Addr, u16 Value)
{
CALC_REGADDR();
*((u16 *)RegAddr) = Value;
}
-unsigned char read_status_reg(SLMP_INFO * info)
+static unsigned char read_status_reg(SLMP_INFO * info)
{
unsigned char *RegAddr = (unsigned char *)info->statctrl_base;
return *RegAddr;
}
-void write_control_reg(SLMP_INFO * info)
+static void write_control_reg(SLMP_INFO * info)
{
unsigned char *RegAddr = (unsigned char *)info->statctrl_base;
*RegAddr = info->port_array[0]->ctrlreg_value;
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff