* VIA VT8233c - UDMA100
* VIA VT8235 - UDMA133
* VIA VT8237 - UDMA133
+ * VIA VT8237A - UDMA133
* VIA VT8237S - UDMA133
* VIA VT8251 - UDMA133
*
#include <linux/init.h>
#include <linux/blkdev.h>
#include <linux/delay.h>
+#include <linux/gfp.h>
#include <scsi/scsi_host.h>
#include <linux/libata.h>
#include <linux/dmi.h>
#define DRV_NAME "pata_via"
#define DRV_VERSION "0.3.4"
-/*
- * The following comes directly from Vojtech Pavlik's ide/pci/via82cxxx
- * driver.
- */
-
enum {
- VIA_UDMA = 0x007,
- VIA_UDMA_NONE = 0x000,
- VIA_UDMA_33 = 0x001,
- VIA_UDMA_66 = 0x002,
- VIA_UDMA_100 = 0x003,
- VIA_UDMA_133 = 0x004,
- VIA_BAD_PREQ = 0x010, /* Crashes if PREQ# till DDACK# set */
- VIA_BAD_CLK66 = 0x020, /* 66 MHz clock doesn't work correctly */
- VIA_SET_FIFO = 0x040, /* Needs to have FIFO split set */
- VIA_NO_UNMASK = 0x080, /* Doesn't work with IRQ unmasking on */
- VIA_BAD_ID = 0x100, /* Has wrong vendor ID (0x1107) */
- VIA_BAD_AST = 0x200, /* Don't touch Address Setup Timing */
- VIA_NO_ENABLES = 0x400, /* Has no enablebits */
- VIA_SATA_PATA = 0x800, /* SATA/PATA combined configuration */
+ VIA_BAD_PREQ = 0x01, /* Crashes if PREQ# till DDACK# set */
+ VIA_BAD_CLK66 = 0x02, /* 66 MHz clock doesn't work correctly */
+ VIA_SET_FIFO = 0x04, /* Needs to have FIFO split set */
+ VIA_NO_UNMASK = 0x08, /* Doesn't work with IRQ unmasking on */
+ VIA_BAD_ID = 0x10, /* Has wrong vendor ID (0x1107) */
+ VIA_BAD_AST = 0x20, /* Don't touch Address Setup Timing */
+ VIA_NO_ENABLES = 0x40, /* Has no enablebits */
+ VIA_SATA_PATA = 0x80, /* SATA/PATA combined configuration */
};
enum {
u16 id;
u8 rev_min;
u8 rev_max;
- u16 flags;
+ u8 udma_mask;
+ u8 flags;
} via_isa_bridges[] = {
- { "vx855", PCI_DEVICE_ID_VIA_VX855, 0x00, 0x2f,
- VIA_UDMA_133 | VIA_BAD_AST | VIA_SATA_PATA },
- { "vx800", PCI_DEVICE_ID_VIA_VX800, 0x00, 0x2f, VIA_UDMA_133 |
- VIA_BAD_AST | VIA_SATA_PATA },
- { "vt8261", PCI_DEVICE_ID_VIA_8261, 0x00, 0x2f,
- VIA_UDMA_133 | VIA_BAD_AST },
- { "vt8237s", PCI_DEVICE_ID_VIA_8237S, 0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST },
- { "vt8251", PCI_DEVICE_ID_VIA_8251, 0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST },
- { "cx700", PCI_DEVICE_ID_VIA_CX700, 0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST | VIA_SATA_PATA },
- { "vt6410", PCI_DEVICE_ID_VIA_6410, 0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST | VIA_NO_ENABLES },
- { "vt6415", PCI_DEVICE_ID_VIA_6415, 0x00, 0xff, VIA_UDMA_133 | VIA_BAD_AST | VIA_NO_ENABLES },
- { "vt8237a", PCI_DEVICE_ID_VIA_8237A, 0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST },
- { "vt8237", PCI_DEVICE_ID_VIA_8237, 0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST },
- { "vt8235", PCI_DEVICE_ID_VIA_8235, 0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST },
- { "vt8233a", PCI_DEVICE_ID_VIA_8233A, 0x00, 0x2f, VIA_UDMA_133 | VIA_BAD_AST },
- { "vt8233c", PCI_DEVICE_ID_VIA_8233C_0, 0x00, 0x2f, VIA_UDMA_100 },
- { "vt8233", PCI_DEVICE_ID_VIA_8233_0, 0x00, 0x2f, VIA_UDMA_100 },
- { "vt8231", PCI_DEVICE_ID_VIA_8231, 0x00, 0x2f, VIA_UDMA_100 },
- { "vt82c686b", PCI_DEVICE_ID_VIA_82C686, 0x40, 0x4f, VIA_UDMA_100 },
- { "vt82c686a", PCI_DEVICE_ID_VIA_82C686, 0x10, 0x2f, VIA_UDMA_66 },
- { "vt82c686", PCI_DEVICE_ID_VIA_82C686, 0x00, 0x0f, VIA_UDMA_33 | VIA_BAD_CLK66 },
- { "vt82c596b", PCI_DEVICE_ID_VIA_82C596, 0x10, 0x2f, VIA_UDMA_66 },
- { "vt82c596a", PCI_DEVICE_ID_VIA_82C596, 0x00, 0x0f, VIA_UDMA_33 | VIA_BAD_CLK66 },
- { "vt82c586b", PCI_DEVICE_ID_VIA_82C586_0, 0x47, 0x4f, VIA_UDMA_33 | VIA_SET_FIFO },
- { "vt82c586b", PCI_DEVICE_ID_VIA_82C586_0, 0x40, 0x46, VIA_UDMA_33 | VIA_SET_FIFO | VIA_BAD_PREQ },
- { "vt82c586b", PCI_DEVICE_ID_VIA_82C586_0, 0x30, 0x3f, VIA_UDMA_33 | VIA_SET_FIFO },
- { "vt82c586a", PCI_DEVICE_ID_VIA_82C586_0, 0x20, 0x2f, VIA_UDMA_33 | VIA_SET_FIFO },
- { "vt82c586", PCI_DEVICE_ID_VIA_82C586_0, 0x00, 0x0f, VIA_UDMA_NONE | VIA_SET_FIFO },
- { "vt82c576", PCI_DEVICE_ID_VIA_82C576, 0x00, 0x2f, VIA_UDMA_NONE | VIA_SET_FIFO | VIA_NO_UNMASK },
- { "vt82c576", PCI_DEVICE_ID_VIA_82C576, 0x00, 0x2f, VIA_UDMA_NONE | VIA_SET_FIFO | VIA_NO_UNMASK | VIA_BAD_ID },
- { "vtxxxx", PCI_DEVICE_ID_VIA_ANON, 0x00, 0x2f,
- VIA_UDMA_133 | VIA_BAD_AST },
+ { "vx855", PCI_DEVICE_ID_VIA_VX855, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST | VIA_SATA_PATA },
+ { "vx800", PCI_DEVICE_ID_VIA_VX800, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST | VIA_SATA_PATA },
+ { "vt8261", PCI_DEVICE_ID_VIA_8261, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST },
+ { "vt8237s", PCI_DEVICE_ID_VIA_8237S, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST },
+ { "vt8251", PCI_DEVICE_ID_VIA_8251, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST },
+ { "cx700", PCI_DEVICE_ID_VIA_CX700, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST | VIA_SATA_PATA },
+ { "vt6410", PCI_DEVICE_ID_VIA_6410, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST | VIA_NO_ENABLES },
+ { "vt6415", PCI_DEVICE_ID_VIA_6415, 0x00, 0xff, ATA_UDMA6, VIA_BAD_AST | VIA_NO_ENABLES },
+ { "vt8237a", PCI_DEVICE_ID_VIA_8237A, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST },
+ { "vt8237", PCI_DEVICE_ID_VIA_8237, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST },
+ { "vt8235", PCI_DEVICE_ID_VIA_8235, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST },
+ { "vt8233a", PCI_DEVICE_ID_VIA_8233A, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST },
+ { "vt8233c", PCI_DEVICE_ID_VIA_8233C_0, 0x00, 0x2f, ATA_UDMA5, },
+ { "vt8233", PCI_DEVICE_ID_VIA_8233_0, 0x00, 0x2f, ATA_UDMA5, },
+ { "vt8231", PCI_DEVICE_ID_VIA_8231, 0x00, 0x2f, ATA_UDMA5, },
+ { "vt82c686b", PCI_DEVICE_ID_VIA_82C686, 0x40, 0x4f, ATA_UDMA5, },
+ { "vt82c686a", PCI_DEVICE_ID_VIA_82C686, 0x10, 0x2f, ATA_UDMA4, },
+ { "vt82c686", PCI_DEVICE_ID_VIA_82C686, 0x00, 0x0f, ATA_UDMA2, VIA_BAD_CLK66 },
+ { "vt82c596b", PCI_DEVICE_ID_VIA_82C596, 0x10, 0x2f, ATA_UDMA4, },
+ { "vt82c596a", PCI_DEVICE_ID_VIA_82C596, 0x00, 0x0f, ATA_UDMA2, VIA_BAD_CLK66 },
+ { "vt82c586b", PCI_DEVICE_ID_VIA_82C586_0, 0x47, 0x4f, ATA_UDMA2, VIA_SET_FIFO },
+ { "vt82c586b", PCI_DEVICE_ID_VIA_82C586_0, 0x40, 0x46, ATA_UDMA2, VIA_SET_FIFO | VIA_BAD_PREQ },
+ { "vt82c586b", PCI_DEVICE_ID_VIA_82C586_0, 0x30, 0x3f, ATA_UDMA2, VIA_SET_FIFO },
+ { "vt82c586a", PCI_DEVICE_ID_VIA_82C586_0, 0x20, 0x2f, ATA_UDMA2, VIA_SET_FIFO },
+ { "vt82c586", PCI_DEVICE_ID_VIA_82C586_0, 0x00, 0x0f, 0x00, VIA_SET_FIFO },
+ { "vt82c576", PCI_DEVICE_ID_VIA_82C576, 0x00, 0x2f, 0x00, VIA_SET_FIFO | VIA_NO_UNMASK },
+ { "vt82c576", PCI_DEVICE_ID_VIA_82C576, 0x00, 0x2f, 0x00, VIA_SET_FIFO | VIA_NO_UNMASK | VIA_BAD_ID },
+ { "vtxxxx", PCI_DEVICE_ID_VIA_ANON, 0x00, 0x2f, ATA_UDMA6, VIA_BAD_AST },
{ NULL }
};
return ATA_CBL_SATA;
/* Early chips are 40 wire */
- if ((config->flags & VIA_UDMA) < VIA_UDMA_66)
+ if (config->udma_mask < ATA_UDMA4)
return ATA_CBL_PATA40;
/* UDMA 66 chips have only drive side logic */
- else if ((config->flags & VIA_UDMA) < VIA_UDMA_100)
+ else if (config->udma_mask < ATA_UDMA5)
return ATA_CBL_PATA_UNK;
/* UDMA 100 or later */
pci_read_config_dword(pdev, 0x50, &ata66);
/**
- * via_do_set_mode - set initial PIO mode data
+ * via_do_set_mode - set transfer mode data
* @ap: ATA interface
* @adev: ATA device
* @mode: ATA mode being programmed
- * @tdiv: Clocks per PCI clock
* @set_ast: Set to program address setup
* @udma_type: UDMA mode/format of registers
*
* on the two channels.
*/
-static void via_do_set_mode(struct ata_port *ap, struct ata_device *adev, int mode, int tdiv, int set_ast, int udma_type)
+static void via_do_set_mode(struct ata_port *ap, struct ata_device *adev,
+ int mode, int set_ast, int udma_type)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
struct ata_device *peer = ata_dev_pair(adev);
struct ata_timing t, p;
- static int via_clock = 33333; /* Bus clock in kHZ - ought to be tunable one day */
+ static int via_clock = 33333; /* Bus clock in kHZ */
unsigned long T = 1000000000 / via_clock;
- unsigned long UT = T/tdiv;
+ unsigned long UT = T;
int ut;
int offset = 3 - (2*ap->port_no) - adev->devno;
+ switch (udma_type) {
+ case ATA_UDMA4:
+ UT = T / 2; break;
+ case ATA_UDMA5:
+ UT = T / 3; break;
+ case ATA_UDMA6:
+ UT = T / 4; break;
+ }
+
/* Calculate the timing values we require */
ata_timing_compute(adev, mode, &t, T, UT);
pci_read_config_byte(pdev, 0x4C, &setup);
setup &= ~(3 << shift);
- setup |= clamp_val(t.setup, 1, 4) << shift; /* 1,4 or 1,4 - 1 FIXME */
+ setup |= (clamp_val(t.setup, 1, 4) - 1) << shift;
pci_write_config_byte(pdev, 0x4C, setup);
}
((clamp_val(t.active, 1, 16) - 1) << 4) | (clamp_val(t.recover, 1, 16) - 1));
/* Load the UDMA bits according to type */
- switch(udma_type) {
- default:
- /* BUG() ? */
- /* fall through */
- case 33:
- ut = t.udma ? (0xe0 | (clamp_val(t.udma, 2, 5) - 2)) : 0x03;
- break;
- case 66:
- ut = t.udma ? (0xe8 | (clamp_val(t.udma, 2, 9) - 2)) : 0x0f;
- break;
- case 100:
- ut = t.udma ? (0xe0 | (clamp_val(t.udma, 2, 9) - 2)) : 0x07;
- break;
- case 133:
- ut = t.udma ? (0xe0 | (clamp_val(t.udma, 2, 9) - 2)) : 0x07;
- break;
+ switch (udma_type) {
+ case ATA_UDMA2:
+ default:
+ ut = t.udma ? (0xe0 | (clamp_val(t.udma, 2, 5) - 2)) : 0x03;
+ break;
+ case ATA_UDMA4:
+ ut = t.udma ? (0xe8 | (clamp_val(t.udma, 2, 9) - 2)) : 0x0f;
+ break;
+ case ATA_UDMA5:
+ ut = t.udma ? (0xe0 | (clamp_val(t.udma, 2, 9) - 2)) : 0x07;
+ break;
+ case ATA_UDMA6:
+ ut = t.udma ? (0xe0 | (clamp_val(t.udma, 2, 9) - 2)) : 0x07;
+ break;
}
/* Set UDMA unless device is not UDMA capable */
{
const struct via_isa_bridge *config = ap->host->private_data;
int set_ast = (config->flags & VIA_BAD_AST) ? 0 : 1;
- int mode = config->flags & VIA_UDMA;
- static u8 tclock[5] = { 1, 1, 2, 3, 4 };
- static u8 udma[5] = { 0, 33, 66, 100, 133 };
- via_do_set_mode(ap, adev, adev->pio_mode, tclock[mode], set_ast, udma[mode]);
+ via_do_set_mode(ap, adev, adev->pio_mode, set_ast, config->udma_mask);
}
static void via_set_dmamode(struct ata_port *ap, struct ata_device *adev)
{
const struct via_isa_bridge *config = ap->host->private_data;
int set_ast = (config->flags & VIA_BAD_AST) ? 0 : 1;
- int mode = config->flags & VIA_UDMA;
- static u8 tclock[5] = { 1, 1, 2, 3, 4 };
- static u8 udma[5] = { 0, 33, 66, 100, 133 };
- via_do_set_mode(ap, adev, adev->dma_mode, tclock[mode], set_ast, udma[mode]);
+ via_do_set_mode(ap, adev, adev->dma_mode, set_ast, config->udma_mask);
}
/**
u8 rev = isa->revision;
pci_dev_put(isa);
+ if ((id->device == 0x0415 || id->device == 0x3164) &&
+ (config->id != id->device))
+ continue;
+
if (rev >= config->rev_min && rev <= config->rev_max)
break;
}
via_config_fifo(pdev, config->flags);
/* Clock set up */
- switch(config->flags & VIA_UDMA) {
- case VIA_UDMA_NONE:
- if (config->flags & VIA_NO_UNMASK)
- ppi[0] = &via_mwdma_info_borked;
- else
- ppi[0] = &via_mwdma_info;
- break;
- case VIA_UDMA_33:
- ppi[0] = &via_udma33_info;
- break;
- case VIA_UDMA_66:
- ppi[0] = &via_udma66_info;
- /* The 66 MHz devices require we enable the clock */
- pci_read_config_dword(pdev, 0x50, &timing);
- timing |= 0x80008;
- pci_write_config_dword(pdev, 0x50, timing);
- break;
- case VIA_UDMA_100:
- ppi[0] = &via_udma100_info;
- break;
- case VIA_UDMA_133:
- ppi[0] = &via_udma133_info;
- break;
- default:
- WARN_ON(1);
- return -ENODEV;
- }
+ switch (config->udma_mask) {
+ case 0x00:
+ if (config->flags & VIA_NO_UNMASK)
+ ppi[0] = &via_mwdma_info_borked;
+ else
+ ppi[0] = &via_mwdma_info;
+ break;
+ case ATA_UDMA2:
+ ppi[0] = &via_udma33_info;
+ break;
+ case ATA_UDMA4:
+ ppi[0] = &via_udma66_info;
+ break;
+ case ATA_UDMA5:
+ ppi[0] = &via_udma100_info;
+ break;
+ case ATA_UDMA6:
+ ppi[0] = &via_udma133_info;
+ break;
+ default:
+ WARN_ON(1);
+ return -ENODEV;
+ }
if (config->flags & VIA_BAD_CLK66) {
/* Disable the 66MHz clock on problem devices */
}
/* We have established the device type, now fire it up */
- return ata_pci_sff_init_one(pdev, ppi, &via_sht, (void *)config);
+ return ata_pci_sff_init_one(pdev, ppi, &via_sht, (void *)config, 0);
}
#ifdef CONFIG_PM
via_config_fifo(pdev, config->flags);
- if ((config->flags & VIA_UDMA) == VIA_UDMA_66) {
+ if (config->udma_mask == ATA_UDMA4) {
/* The 66 MHz devices require we enable the clock */
pci_read_config_dword(pdev, 0x50, &timing);
timing |= 0x80008;
{ PCI_VDEVICE(VIA, 0x3164), },
{ PCI_VDEVICE(VIA, 0x5324), },
{ PCI_VDEVICE(VIA, 0xC409), VIA_IDFLAG_SINGLE },
+ { PCI_VDEVICE(VIA, 0x9001), VIA_IDFLAG_SINGLE },
{ },
};
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff