* Some drives were very specific about that exact sequence.
*
* Note that ATA4 says lba is mandatory so the second check
- * shoud never trigger.
+ * should never trigger.
*/
if (ata_id_major_version(id) < 4 || !ata_id_has_lba(id)) {
err_mask = ata_dev_init_params(dev, id[3], id[6]);
int ata_timing_compute(struct ata_device *adev, unsigned short speed,
struct ata_timing *t, int T, int UT)
{
+ const u16 *id = adev->id;
const struct ata_timing *s;
struct ata_timing p;
* PIO/MW_DMA cycle timing.
*/
- if (adev->id[ATA_ID_FIELD_VALID] & 2) { /* EIDE drive */
+ if (id[ATA_ID_FIELD_VALID] & 2) { /* EIDE drive */
memset(&p, 0, sizeof(p));
+
if (speed >= XFER_PIO_0 && speed <= XFER_SW_DMA_0) {
- if (speed <= XFER_PIO_2) p.cycle = p.cyc8b = adev->id[ATA_ID_EIDE_PIO];
- else p.cycle = p.cyc8b = adev->id[ATA_ID_EIDE_PIO_IORDY];
- } else if (speed >= XFER_MW_DMA_0 && speed <= XFER_MW_DMA_2) {
- p.cycle = adev->id[ATA_ID_EIDE_DMA_MIN];
- }
+ if (speed <= XFER_PIO_2)
+ p.cycle = p.cyc8b = id[ATA_ID_EIDE_PIO];
+ else if ((speed <= XFER_PIO_4) ||
+ (speed == XFER_PIO_5 && !ata_id_is_cfa(id)))
+ p.cycle = p.cyc8b = id[ATA_ID_EIDE_PIO_IORDY];
+ } else if (speed >= XFER_MW_DMA_0 && speed <= XFER_MW_DMA_2)
+ p.cycle = id[ATA_ID_EIDE_DMA_MIN];
+
ata_timing_merge(&p, t, t, ATA_TIMING_CYCLE | ATA_TIMING_CYC8B);
}
int sata_link_resume(struct ata_link *link, const unsigned long *params,
unsigned long deadline)
{
+ int tries = ATA_LINK_RESUME_TRIES;
u32 scontrol, serror;
int rc;
if ((rc = sata_scr_read(link, SCR_CONTROL, &scontrol)))
return rc;
- scontrol = (scontrol & 0x0f0) | 0x300;
+ /*
+ * Writes to SControl sometimes get ignored under certain
+ * controllers (ata_piix SIDPR). Make sure DET actually is
+ * cleared.
+ */
+ do {
+ scontrol = (scontrol & 0x0f0) | 0x300;
+ if ((rc = sata_scr_write(link, SCR_CONTROL, scontrol)))
+ return rc;
+ /*
+ * Some PHYs react badly if SStatus is pounded
+ * immediately after resuming. Delay 200ms before
+ * debouncing.
+ */
+ msleep(200);
- if ((rc = sata_scr_write(link, SCR_CONTROL, scontrol)))
- return rc;
+ /* is SControl restored correctly? */
+ if ((rc = sata_scr_read(link, SCR_CONTROL, &scontrol)))
+ return rc;
+ } while ((scontrol & 0xf0f) != 0x300 && --tries);
- /* Some PHYs react badly if SStatus is pounded immediately
- * after resuming. Delay 200ms before debouncing.
- */
- msleep(200);
+ if ((scontrol & 0xf0f) != 0x300) {
+ ata_link_printk(link, KERN_ERR,
+ "failed to resume link (SControl %X)\n",
+ scontrol);
+ return 0;
+ }
+
+ if (tries < ATA_LINK_RESUME_TRIES)
+ ata_link_printk(link, KERN_WARNING,
+ "link resume succeeded after %d retries\n",
+ ATA_LINK_RESUME_TRIES - tries);
if ((rc = sata_link_debounce(link, params, deadline)))
return rc;
*/
void ata_qc_free(struct ata_queued_cmd *qc)
{
- struct ata_port *ap = qc->ap;
+ struct ata_port *ap;
unsigned int tag;
WARN_ON_ONCE(qc == NULL); /* ata_qc_from_tag _might_ return NULL */
+ ap = qc->ap;
qc->flags = 0;
tag = qc->tag;
void __ata_qc_complete(struct ata_queued_cmd *qc)
{
- struct ata_port *ap = qc->ap;
- struct ata_link *link = qc->dev->link;
+ struct ata_port *ap;
+ struct ata_link *link;
WARN_ON_ONCE(qc == NULL); /* ata_qc_from_tag _might_ return NULL */
WARN_ON_ONCE(!(qc->flags & ATA_QCFLAG_ACTIVE));
+ ap = qc->ap;
+ link = qc->dev->link;
if (likely(qc->flags & ATA_QCFLAG_DMAMAP))
ata_sg_clean(qc);
qc->flags |= ATA_QCFLAG_FAILED;
if (unlikely(qc->flags & ATA_QCFLAG_FAILED)) {
- if (!ata_tag_internal(qc->tag)) {
- /* always fill result TF for failed qc */
- fill_result_tf(qc);
+ /* always fill result TF for failed qc */
+ fill_result_tf(qc);
+
+ if (!ata_tag_internal(qc->tag))
ata_qc_schedule_eh(qc);
- return;
- }
+ else
+ __ata_qc_complete(qc);
+ return;
}
WARN_ON_ONCE(ap->pflags & ATA_PFLAG_FROZEN);
{
ata_parse_force_param();
+ /*
+ * FIXME: In UP case, there is only one workqueue thread and if you
+ * have more than one PIO device, latency is bloody awful, with
+ * occasional multi-second "hiccups" as one PIO device waits for
+ * another. It's an ugly wart that users DO occasionally complain
+ * about; luckily most users have at most one PIO polled device.
+ */
ata_wq = create_workqueue("ata");
if (!ata_wq)
goto free_force_tbl;