#include <linux/stddef.h>
#include <linux/unistd.h>
#include <linux/ptrace.h>
-#include <linux/slab.h>
#include <linux/user.h>
-#include <linux/a.out.h>
#include <linux/tty.h>
#include <linux/major.h>
#include <linux/interrupt.h>
#include <linux/reboot.h>
#include <linux/init.h>
#include <linux/pci.h>
-#include <linux/utsrelease.h>
+#include <generated/utsrelease.h>
#include <linux/adb.h>
#include <linux/module.h>
#include <linux/delay.h>
DEFINE_PER_CPU(struct timer_list, heartbeat_timer);
unsigned long event_scan_interval;
-/*
- * XXX this should be in xmon.h, but putting it there means xmon.h
- * has to include <linux/interrupt.h> (to get irqreturn_t), which
- * causes all sorts of problems. -- paulus
- */
-extern irqreturn_t xmon_irq(int, void *);
-
extern unsigned long loops_per_jiffy;
/* To be replaced by RTAS when available */
for(;;);
}
+/*
+ * Per default, input/output-device points to the keyboard/screen
+ * If no card is installed, the built-in serial port is used as a fallback.
+ * But unfortunately, the firmware does not connect /chosen/{stdin,stdout}
+ * the the built-in serial node. Instead, a /failsafe node is created.
+ */
+static void chrp_init_early(void)
+{
+ struct device_node *node;
+ const char *property;
+
+ if (strstr(cmd_line, "console="))
+ return;
+ /* find the boot console from /chosen/stdout */
+ if (!of_chosen)
+ return;
+ node = of_find_node_by_path("/");
+ if (!node)
+ return;
+ property = of_get_property(node, "model", NULL);
+ if (!property)
+ goto out_put;
+ if (strcmp(property, "Pegasos2"))
+ goto out_put;
+ /* this is a Pegasos2 */
+ property = of_get_property(of_chosen, "linux,stdout-path", NULL);
+ if (!property)
+ goto out_put;
+ of_node_put(node);
+ node = of_find_node_by_path(property);
+ if (!node)
+ return;
+ property = of_get_property(node, "device_type", NULL);
+ if (!property)
+ goto out_put;
+ if (strcmp(property, "serial"))
+ goto out_put;
+ /*
+ * The 9pin connector is either /failsafe
+ * or /pci@80000000/isa@C/serial@i2F8
+ * The optional graphics card has also type 'serial' in VGA mode.
+ */
+ property = of_get_property(node, "name", NULL);
+ if (!property)
+ goto out_put;
+ if (!strcmp(property, "failsafe") || !strcmp(property, "serial"))
+ add_preferred_console("ttyS", 0, NULL);
+out_put:
+ of_node_put(node);
+}
+
void __init chrp_setup_arch(void)
{
struct device_node *root = of_find_node_by_path("/");
if (ppc_md.progress) ppc_md.progress("Linux/PPC "UTS_RELEASE"\n", 0x0);
}
-void
-chrp_event_scan(unsigned long unused)
-{
- unsigned char log[1024];
- int ret = 0;
-
- /* XXX: we should loop until the hardware says no more error logs -- Cort */
- rtas_call(rtas_token("event-scan"), 4, 1, &ret, 0xffffffff, 0,
- __pa(log), 1024);
- mod_timer(&__get_cpu_var(heartbeat_timer),
- jiffies + event_scan_interval);
-}
-
static void chrp_8259_cascade(unsigned int irq, struct irq_desc *desc)
{
unsigned int cascade_irq = i8259_irq();
#if defined(CONFIG_VT) && defined(CONFIG_INPUT_ADBHID) && defined(CONFIG_XMON)
static struct irqaction xmon_irqaction = {
.handler = xmon_irq,
- .mask = CPU_MASK_NONE,
.name = "XMON break",
};
#endif
void __init
chrp_init2(void)
{
- struct device_node *device;
- const unsigned int *p = NULL;
-
#ifdef CONFIG_NVRAM
chrp_nvram_init();
#endif
request_region(0x80,0x10,"dma page reg");
request_region(0xc0,0x20,"dma2");
- /* Get the event scan rate for the rtas so we know how
- * often it expects a heartbeat. -- Cort
- */
- device = of_find_node_by_name(NULL, "rtas");
- if (device)
- p = of_get_property(device, "rtas-event-scan-rate", NULL);
- if (p && *p) {
- /*
- * Arrange to call chrp_event_scan at least *p times
- * per minute. We use 59 rather than 60 here so that
- * the rate will be slightly higher than the minimum.
- * This all assumes we don't do hotplug CPU on any
- * machine that needs the event scans done.
- */
- unsigned long interval, offset;
- int cpu, ncpus;
- struct timer_list *timer;
-
- interval = HZ * 59 / *p;
- offset = HZ;
- ncpus = num_online_cpus();
- event_scan_interval = ncpus * interval;
- for (cpu = 0; cpu < ncpus; ++cpu) {
- timer = &per_cpu(heartbeat_timer, cpu);
- setup_timer(timer, chrp_event_scan, 0);
- timer->expires = jiffies + offset;
- add_timer_on(timer, cpu);
- offset += interval;
- }
- printk("RTAS Event Scan Rate: %u (%lu jiffies)\n",
- *p, interval);
- }
- of_node_put(device);
-
if (ppc_md.progress)
ppc_md.progress(" Have fun! ", 0x7777);
}
.probe = chrp_probe,
.setup_arch = chrp_setup_arch,
.init = chrp_init2,
+ .init_early = chrp_init_early,
.show_cpuinfo = chrp_show_cpuinfo,
.init_IRQ = chrp_init_IRQ,
.restart = rtas_restart,