config MIPS
bool
default y
+ select HAVE_IDE
+ select HAVE_OPROFILE
+ select HAVE_ARCH_KGDB
# Horrible source of confusion. Die, die, die ...
select EMBEDDED
select RTC_LIB
select SYS_HAS_CPU_RM9000
select SYS_SUPPORTS_32BIT_KERNEL
select SYS_SUPPORTS_BIG_ENDIAN
- select SYS_SUPPORTS_KGDB
help
The eXcite is a smart camera platform manufactured by
Basler Vision Technologies AG.
select SSB
select SSB_DRIVER_MIPS
select SSB_DRIVER_EXTIF
+ select SSB_EMBEDDED
select SSB_PCICORE_HOSTMODE if PCI
select GENERIC_GPIO
select SYS_HAS_EARLY_PRINTK
select SYS_HAS_CPU_NEVADA
select SYS_HAS_EARLY_PRINTK
select SYS_SUPPORTS_32BIT_KERNEL
- select SYS_SUPPORTS_64BIT_KERNEL if EXPERIMENTAL
+ select SYS_SUPPORTS_64BIT_KERNEL
select SYS_SUPPORTS_LITTLE_ENDIAN
select GENERIC_HARDIRQS_NO__DO_IRQ
config MACH_DECSTATION
bool "DECstations"
select BOOT_ELF32
+ select CEVT_DS1287
select CEVT_R4K
+ select CSRC_IOASIC
select CSRC_R4K
select CPU_DADDI_WORKAROUNDS if 64BIT
select CPU_R4000_WORKAROUNDS if 64BIT
Lemote Fulong mini-PC board based on the Chinese Loongson-2E CPU and
an FPGA northbridge
-config MIPS_ATLAS
- bool "MIPS Atlas board"
- select BOOT_ELF32
- select BOOT_RAW
- select CEVT_R4K
- select CSRC_R4K
- select DMA_NONCOHERENT
- select SYS_HAS_EARLY_PRINTK
- select IRQ_CPU
- select HW_HAS_PCI
- select MIPS_BOARDS_GEN
- select MIPS_BONITO64
- select PCI_GT64XXX_PCI0
- select MIPS_MSC
- select RM7000_CPU_SCACHE
- select SWAP_IO_SPACE
- select SYS_HAS_CPU_MIPS32_R1
- select SYS_HAS_CPU_MIPS32_R2
- select SYS_HAS_CPU_MIPS64_R1
- select SYS_HAS_CPU_NEVADA
- select SYS_HAS_CPU_RM7000
- select SYS_SUPPORTS_32BIT_KERNEL
- select SYS_SUPPORTS_64BIT_KERNEL
- select SYS_SUPPORTS_BIG_ENDIAN
- select SYS_SUPPORTS_LITTLE_ENDIAN
- select SYS_SUPPORTS_MULTITHREADING if EXPERIMENTAL
- select SYS_SUPPORTS_SMARTMIPS
- select GENERIC_HARDIRQS_NO__DO_IRQ
- help
- This enables support for the MIPS Technologies Atlas evaluation
- board.
-
config MIPS_MALTA
bool "MIPS Malta board"
select ARCH_MAY_HAVE_PC_FDC
select DMA_NONCOHERENT
select GENERIC_ISA_DMA
select IRQ_CPU
+ select IRQ_GIC
select HW_HAS_PCI
select I8253
select I8259
select SYS_SUPPORTS_64BIT_KERNEL
select SYS_SUPPORTS_BIG_ENDIAN
select SYS_SUPPORTS_LITTLE_ENDIAN
+ select SYS_SUPPORTS_MIPS_CMP if BROKEN # because SYNC_R4K is broken
select SYS_SUPPORTS_MULTITHREADING
select SYS_SUPPORTS_SMARTMIPS
help
This enables support for the MIPS Technologies Malta evaluation
board.
-config MIPS_SEAD
- bool "MIPS SEAD board"
- select CEVT_R4K
- select CSRC_R4K
- select IRQ_CPU
- select DMA_NONCOHERENT
- select SYS_HAS_EARLY_PRINTK
- select MIPS_BOARDS_GEN
- select SYS_HAS_CPU_MIPS32_R1
- select SYS_HAS_CPU_MIPS32_R2
- select SYS_HAS_CPU_MIPS64_R1
- select SYS_SUPPORTS_32BIT_KERNEL
- select SYS_SUPPORTS_64BIT_KERNEL if EXPERIMENTAL
- select SYS_SUPPORTS_BIG_ENDIAN
- select SYS_SUPPORTS_LITTLE_ENDIAN
- select SYS_SUPPORTS_SMARTMIPS
- help
- This enables support for the MIPS Technologies SEAD evaluation
- board.
-
config MIPS_SIM
bool 'MIPS simulator (MIPSsim)'
select CEVT_R4K
select GENERIC_HARDIRQS_NO__DO_IRQ
config PNX8550_JBS
- bool "Philips PNX8550 based JBS board"
+ bool "NXP PNX8550 based JBS board"
select PNX8550
select SYS_SUPPORTS_LITTLE_ENDIAN
config PNX8550_STB810
- bool "Philips PNX8550 based STB810 board"
+ bool "NXP PNX8550 based STB810 board"
select PNX8550
select SYS_SUPPORTS_LITTLE_ENDIAN
select SYS_HAS_CPU_MIPS32_R2
select SYS_SUPPORTS_32BIT_KERNEL
select SYS_SUPPORTS_BIG_ENDIAN
- select SYS_SUPPORTS_KGDB
select IRQ_CPU
select SERIAL_8250
select SERIAL_8250_CONSOLE
select SYS_SUPPORTS_64BIT_KERNEL
select SYS_SUPPORTS_BIG_ENDIAN
select SYS_SUPPORTS_HIGHMEM
- select SYS_SUPPORTS_KGDB
select SYS_SUPPORTS_SMP
help
Yosemite is an evaluation board for the RM9000x2 processor
select SGI_HAS_DS1286
select SGI_HAS_I8042
select SGI_HAS_INDYDOG
+ select SGI_HAS_HAL2
select SGI_HAS_SEEQ
select SGI_HAS_WD93
select SGI_HAS_ZILOG
select SYS_HAS_CPU_R10000
select SYS_SUPPORTS_64BIT_KERNEL
select SYS_SUPPORTS_BIG_ENDIAN
- select SYS_SUPPORTS_KGDB
select SYS_SUPPORTS_NUMA
select SYS_SUPPORTS_SMP
select GENERIC_HARDIRQS_NO__DO_IRQ
select SGI_HAS_DS1286
select SGI_HAS_I8042
select SGI_HAS_INDYDOG
+ select SGI_HAS_HAL2
select SGI_HAS_SEEQ
select SGI_HAS_WD93
select SGI_HAS_ZILOG
select SYS_HAS_CPU_SB1
select SYS_SUPPORTS_BIG_ENDIAN
select SYS_SUPPORTS_HIGHMEM
- select SYS_SUPPORTS_KGDB
select SYS_SUPPORTS_LITTLE_ENDIAN
select ZONE_DMA32 if 64BIT
Technology and now in turn merged with Fujitsu. Say Y here to
support this machine type.
-config TOSHIBA_JMR3927
- bool "Toshiba JMR-TX3927 board"
- select CEVT_TXX9
- select DMA_NONCOHERENT
- select HW_HAS_PCI
- select MIPS_TX3927
- select IRQ_TXX9
- select SWAP_IO_SPACE
- select SYS_HAS_CPU_TX39XX
- select SYS_SUPPORTS_32BIT_KERNEL
- select SYS_SUPPORTS_LITTLE_ENDIAN
- select SYS_SUPPORTS_BIG_ENDIAN
- select GENERIC_HARDIRQS_NO__DO_IRQ
+config MACH_TX39XX
+ bool "Toshiba TX39 series based machines"
-config TOSHIBA_RBTX4927
- bool "Toshiba RBTX49[23]7 board"
- select CEVT_R4K
- select CSRC_R4K
- select CEVT_TXX9
- select DMA_NONCOHERENT
- select HAS_TXX9_SERIAL
- select HW_HAS_PCI
- select IRQ_CPU
- select IRQ_TXX9
- select I8259 if TOSHIBA_FPCIB0
- select SWAP_IO_SPACE
- select SYS_HAS_CPU_TX49XX
- select SYS_SUPPORTS_32BIT_KERNEL
- select SYS_SUPPORTS_64BIT_KERNEL
- select SYS_SUPPORTS_LITTLE_ENDIAN
- select SYS_SUPPORTS_BIG_ENDIAN
- select SYS_SUPPORTS_KGDB
- select GENERIC_HARDIRQS_NO__DO_IRQ
- help
- This Toshiba board is based on the TX4927 processor. Say Y here to
- support this machine type
+config MACH_TX49XX
+ bool "Toshiba TX49 series based machines"
-config TOSHIBA_RBTX4938
- bool "Toshiba RBTX4938 board"
+config MIKROTIK_RB532
+ bool "Mikrotik RB532 boards"
select CEVT_R4K
select CSRC_R4K
- select CEVT_TXX9
select DMA_NONCOHERENT
- select HAS_TXX9_SERIAL
+ select GENERIC_HARDIRQS_NO__DO_IRQ
select HW_HAS_PCI
select IRQ_CPU
- select IRQ_TXX9
- select SWAP_IO_SPACE
- select SYS_HAS_CPU_TX49XX
+ select SYS_HAS_CPU_MIPS32_R1
select SYS_SUPPORTS_32BIT_KERNEL
select SYS_SUPPORTS_LITTLE_ENDIAN
- select SYS_SUPPORTS_BIG_ENDIAN
- select SYS_SUPPORTS_KGDB
- select GENERIC_HARDIRQS_NO__DO_IRQ
- select GENERIC_GPIO
+ select SWAP_IO_SPACE
+ select BOOT_RAW
+ select ARCH_REQUIRE_GPIOLIB
help
- This Toshiba board is based on the TX4938 processor. Say Y here to
- support this machine type
+ Support the Mikrotik(tm) RouterBoard 532 series,
+ based on the IDT RC32434 SoC.
config WR_PPMC
bool "Wind River PPMC board"
endchoice
-source "arch/mips/au1000/Kconfig"
+source "arch/mips/alchemy/Kconfig"
source "arch/mips/basler/excite/Kconfig"
source "arch/mips/jazz/Kconfig"
source "arch/mips/lasat/Kconfig"
source "arch/mips/pmc-sierra/Kconfig"
source "arch/mips/sgi-ip27/Kconfig"
source "arch/mips/sibyte/Kconfig"
-source "arch/mips/tx4927/Kconfig"
-source "arch/mips/tx4938/Kconfig"
+source "arch/mips/txx9/Kconfig"
source "arch/mips/vr41xx/Kconfig"
endmenu
config CEVT_BCM1480
bool
+config CEVT_DS1287
+ bool
+
config CEVT_GT641XX
bool
config CSRC_BCM1480
bool
+config CSRC_IOASIC
+ bool
+
config CSRC_R4K
bool
config CSRC_SB1250
bool
+config GPIO_TXX9
+ select GENERIC_GPIO
+ select ARCH_REQUIRE_GPIOLIB
+ bool
+
config CFE
bool
config MIPS_DISABLE_OBSOLETE_IDE
bool
+config SYNC_R4K
+ bool
+
config NO_IOPORT
def_bool n
config IRQ_GT641XX
bool
+config IRQ_GIC
+ bool
+
config MIPS_BOARDS_GEN
bool
config NO_EXCEPT_FILL
bool
-config MIPS_TX3927
- bool
- select HAS_TXX9_SERIAL
-
config MIPS_RM9122
bool
select SERIAL_RM9000
select SYS_HAS_EARLY_PRINTK
select SYS_SUPPORTS_32BIT_KERNEL
select GENERIC_HARDIRQS_NO__DO_IRQ
- select SYS_SUPPORTS_KGDB
select GENERIC_GPIO
config SWAP_IO_SPACE
config SGI_HAS_INDYDOG
bool
+config SGI_HAS_HAL2
+ bool
+
config SGI_HAS_SEEQ
bool
config MIPS_L1_CACHE_SHIFT
int
- default "4" if MACH_DECSTATION
- default "7" if SGI_IP27 || SGI_IP28 || SNI_RM
+ default "4" if MACH_DECSTATION || MIKROTIK_RB532
+ default "7" if SGI_IP22 || SGI_IP27 || SGI_IP28 || SNI_RM
default "4" if PMC_MSP4200_EVAL
default "5"
config CPU_SUPPORTS_64BIT_KERNEL
bool
+#
+# Set to y for ptrace access to watch registers.
+#
+config HARDWARE_WATCHPOINTS
+ bool
+ default y if CPU_MIPS32 || CPU_MIPS64
+
menu "Kernel type"
choice
depends on CPU_MIPS32_R2
#depends on CPU_MIPS64_R2 # once there is hardware ...
depends on SYS_SUPPORTS_MULTITHREADING
- select GENERIC_CLOCKEVENTS_BROADCAST
select CPU_MIPSR2_IRQ_VI
select CPU_MIPSR2_IRQ_EI
select MIPS_MT
Includes a loader for loading an elf relocatable object
onto another VPE and running it.
-config MIPS_MT_SMTC_INSTANT_REPLAY
- bool "Low-latency Dispatch of Deferred SMTC IPIs"
- depends on MIPS_MT_SMTC && !PREEMPT
- default y
- help
- SMTC pseudo-interrupts between TCs are deferred and queued
- if the target TC is interrupt-inhibited (IXMT). In the first
- SMTC prototypes, these queued IPIs were serviced on return
- to user mode, or on entry into the kernel idle loop. The
- INSTANT_REPLAY option dispatches them as part of local_irq_restore()
- processing, which adds runtime overhead (hence the option to turn
- it off), but ensures that IPIs are handled promptly even under
- heavy I/O interrupt load.
-
config MIPS_MT_SMTC_IM_BACKSTOP
bool "Use per-TC register bits as backstop for inhibited IM bits"
depends on MIPS_MT_SMTC
- default y
+ default n
help
To support multiple TC microthreads acting as "CPUs" within
a VPE, VPE-wide interrupt mask bits must be specially manipulated
during interrupt handling. To support legacy drivers and interrupt
controller management code, SMTC has a "backstop" to track and
if necessary restore the interrupt mask. This has some performance
- impact on interrupt service overhead. Disable it only if you know
- what you are doing.
+ impact on interrupt service overhead.
config MIPS_MT_SMTC_IRQAFF
bool "Support IRQ affinity API"
Enables SMP IRQ affinity API (/proc/irq/*/smp_affinity, etc.)
for SMTC Linux kernel. Requires platform support, of which
an example can be found in the MIPS kernel i8259 and Malta
- platform code. It is recommended that MIPS_MT_SMTC_INSTANT_REPLAY
- be enabled if MIPS_MT_SMTC_IRQAFF is used. Adds overhead to
- interrupt dispatch, and should be used only if you know what
- you are doing.
+ platform code. Adds some overhead to interrupt dispatch, and
+ should be used only if you know what you are doing.
config MIPS_VPE_LOADER_TOM
bool "Load VPE program into memory hidden from linux"
"exit" syscall notifying other kernel modules the SP program is
exiting. You probably want to say yes here.
+config MIPS_CMP
+ bool "MIPS CMP framework support"
+ depends on SYS_SUPPORTS_MIPS_CMP
+ select SYNC_R4K if BROKEN
+ select SYS_SUPPORTS_SMP
+ select SYS_SUPPORTS_SCHED_SMT if SMP
+ select WEAK_ORDERING
+ default n
+ help
+ This is a placeholder option for the GCMP work. It will need to
+ be handled differently...
+
config SB1_PASS_1_WORKAROUNDS
bool
depends on CPU_SB1_PASS_1
bool "Multi-Processing support"
depends on SYS_SUPPORTS_SMP
select IRQ_PER_CPU
+ select USE_GENERIC_SMP_HELPERS
help
This enables support for systems with more than one CPU. If you have
a system with only one CPU, like most personal computers, say N. If
People using multiprocessor machines who say Y here should also say
Y to "Enhanced Real Time Clock Support", below.
- See also the <file:Documentation/smp.txt> and the SMP-HOWTO
- available at <http://www.tldp.org/docs.html#howto>.
+ See also the SMP-HOWTO available at
+ <http://www.tldp.org/docs.html#howto>.
If you don't know what to do here, say N.
config SMP_UP
bool
+config SYS_SUPPORTS_MIPS_CMP
+ bool
+
config SYS_SUPPORTS_SMP
bool
Allows the configuration of the timer frequency.
config HZ_48
- bool "48 HZ" if SYS_SUPPORTS_48HZ
+ bool "48 HZ" if SYS_SUPPORTS_48HZ || SYS_SUPPORTS_ARBIT_HZ
config HZ_100
bool "100 HZ" if SYS_SUPPORTS_100HZ || SYS_SUPPORTS_ARBIT_HZ
source "init/Kconfig"
+config PROBE_INITRD_HEADER
+ bool "Probe initrd header created by addinitrd"
+ depends on BLK_DEV_INITRD
+ help
+ Probe initrd header at the last page of kernel image.
+ Say Y here if you are using arch/mips/boot/addinitrd.c to
+ add initrd or initramfs image to the kernel image.
+ Otherwise, say N.
+
+source "kernel/Kconfig.freezer"
+
menu "Bus options (PCI, PCMCIA, EISA, ISA, TC)"
config HW_HAS_EISA
your box. Other bus systems are ISA, EISA, or VESA. If you have PCI,
say Y, otherwise N.
- The PCI-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>, contains valuable
- information about which PCI hardware does work under Linux and which
- doesn't.
-
config PCI_DOMAINS
bool
config TRAD_SIGNALS
bool
-config BINFMT_IRIX
- bool "Include IRIX binary compatibility"
- depends on CPU_BIG_ENDIAN && 32BIT && BROKEN
-
config MIPS32_COMPAT
bool "Kernel support for Linux/MIPS 32-bit binary compatibility"
depends on 64BIT
menu "Power management options"
+config ARCH_SUSPEND_POSSIBLE
+ def_bool y
+ depends on !SMP
+
source "kernel/power/Kconfig"
endmenu
source "fs/Kconfig"
-source "kernel/Kconfig.instrumentation"
-
source "arch/mips/Kconfig.debug"
source "security/Kconfig"
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff