config M68K
bool
default y
+ select HAVE_AOUT
+ select HAVE_IDE
config MMU
bool
config RWSEM_XCHGADD_ALGORITHM
bool
+config ARCH_HAS_ILOG2_U32
+ bool
+ default n
+
+config ARCH_HAS_ILOG2_U64
+ bool
+ default n
+
+config GENERIC_HWEIGHT
+ bool
+ default y
+
config GENERIC_CALIBRATE_DELAY
bool
default y
+config TIME_LOW_RES
+ bool
+ default y
+
+config GENERIC_IOMAP
+ bool
+ default y
+
config ARCH_MAY_HAVE_PC_FDC
bool
- depends on Q40 || (BROKEN && SUN3X)
+ depends on BROKEN && (Q40 || SUN3X)
default y
+config NO_IOPORT
+ def_bool y
+
+config NO_DMA
+ def_bool SUN3
+
+config HZ
+ int
+ default 100
+
mainmenu "Linux/68k Kernel Configuration"
source "init/Kconfig"
+source "kernel/Kconfig.freezer"
+
menu "Platform dependent setup"
config EISA
To compile this driver as modules, choose M here: the
modules will be called pcmcia_core and ds.
-config SUN3
- bool "Sun3 support"
- select M68020
- select MMU_SUN3 if MMU
- help
- This option enables support for the Sun 3 series of workstations
- (3/50, 3/60, 3/1xx, 3/2xx systems). Enabling this option requires
- that all other hardware types must be disabled, as Sun 3 kernels
- are incompatible with all other m68k targets (including Sun 3x!).
-
- If you don't want to compile a kernel exclusively for a Sun 3, say N.
-
config AMIGA
bool "Amiga support"
- depends on !MMU_SUN3
+ select MMU_MOTOROLA if MMU
help
This option enables support for the Amiga series of computers. If
you plan to use this kernel on an Amiga, say Y here and browse the
config ATARI
bool "Atari support"
- depends on !MMU_SUN3
+ select MMU_MOTOROLA if MMU
help
This option enables support for the 68000-based Atari series of
computers (including the TT, Falcon and Medusa). If you plan to use
this kernel on an Atari, say Y here and browse the material
available in <file:Documentation/m68k>; otherwise say N.
-config HADES
- bool "Hades support"
- depends on ATARI && BROKEN
- help
- This option enables support for the Hades Atari clone. If you plan
- to use this kernel on a Hades, say Y here; otherwise say N.
-
-config PCI
- bool
- depends on HADES
- default y
- help
- Find out whether you have a PCI motherboard. PCI is the name of a
- bus system, i.e. the way the CPU talks to the other stuff inside
- your box. Other bus systems are ISA, EISA, MicroChannel (MCA) or
- VESA. If you have PCI, say Y, otherwise N.
-
- The PCI-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>, contains valuable
- information about which PCI hardware does work under Linux and which
- doesn't.
-
config MAC
bool "Macintosh support"
- depends on !MMU_SUN3
+ select MMU_MOTOROLA if MMU
help
This option enables support for the Apple Macintosh series of
computers (yes, there is experimental support now, at least for part
config APOLLO
bool "Apollo support"
- depends on !MMU_SUN3
+ select MMU_MOTOROLA if MMU
help
Say Y here if you want to run Linux on an MC680x0-based Apollo
Domain workstation such as the DN3500.
config VME
bool "VME (Motorola and BVM) support"
- depends on !MMU_SUN3
+ select MMU_MOTOROLA if MMU
help
Say Y here if you want to build a kernel for a 680x0 based VME
board. Boards currently supported include Motorola boards MVME147,
config HP300
bool "HP9000/300 and HP9000/400 support"
- depends on !MMU_SUN3
+ select MMU_MOTOROLA if MMU
help
This option enables support for the HP9000/300 and HP9000/400 series
of workstations. Support for these machines is still somewhat
config SUN3X
bool "Sun3x support"
- depends on !MMU_SUN3
+ select MMU_MOTOROLA if MMU
select M68030
help
This option enables support for the Sun 3x series of workstations.
config Q40
bool "Q40/Q60 support"
- depends on !MMU_SUN3
+ select MMU_MOTOROLA if MMU
help
The Q40 is a Motorola 68040-based successor to the Sinclair QL
manufactured in Germany. There is an official Q40 home page at
Q60. Select your CPU below. For 68LC060 don't forget to enable FPU
emulation.
+config SUN3
+ bool "Sun3 support"
+ depends on !MMU_MOTOROLA
+ select MMU_SUN3 if MMU
+ select M68020
+ help
+ This option enables support for the Sun 3 series of workstations
+ (3/50, 3/60, 3/1xx, 3/2xx systems). Enabling this option requires
+ that all other hardware types must be disabled, as Sun 3 kernels
+ are incompatible with all other m68k targets (including Sun 3x!).
+
+ If you don't want to compile a kernel exclusively for a Sun 3, say N.
+
comment "Processor type"
config M68020
config MMU_MOTOROLA
bool
depends on MMU && !MMU_SUN3
- default y
config MMU_SUN3
bool
+ depends on MMU && !MMU_MOTOROLA
config M68KFPU_EMU
bool "Math emulation support (EXPERIMENTAL)"
adventurous.
config SINGLE_MEMORY_CHUNK
- bool "Use one physical chunk of memory only"
- depends on ADVANCED && !SUN3
+ bool "Use one physical chunk of memory only" if ADVANCED && !SUN3
+ default y if SUN3
+ select NEED_MULTIPLE_NODES
help
Ignore all but the first contiguous chunk of physical memory for VM
purposes. This will save a few bytes kernel size and may speed up
is hardwired on. The 53c710 SCSI driver is known to suffer from
this problem.
+config ARCH_DISCONTIGMEM_ENABLE
+ def_bool !SINGLE_MEMORY_CHUNK
+
+config NODES_SHIFT
+ int
+ default "3"
+ depends on !SINGLE_MEMORY_CHUNK
+
source "mm/Kconfig"
endmenu
depends on Q40 || AMIGA_PCMCIA || GG2
default y
+config ZONE_DMA
+ bool
+ default y
+
source "drivers/pci/Kconfig"
source "drivers/zorro/Kconfig"
Note for Falcon users: You also have an MFP port, it's just not
wired to the outside... But you could use the port under Linux.
-config ATARI_SCC
- tristate "Atari SCC serial support"
- depends on ATARI
- ---help---
- If you have serial ports based on a Zilog SCC chip (Modem2, Serial2,
- LAN) and like to use them under Linux, say Y. All built-in SCC's are
- supported (TT, MegaSTE, Falcon), and also the ST-ESCC. If you have
- two connectors for channel A (Serial2 and LAN), they are visible as
- two separate devices.
-
- To compile this driver as a module, choose M here.
-
-config ATARI_SCC_DMA
- bool "Atari SCC serial DMA support"
- depends on ATARI_SCC
- help
- This enables DMA support for receiving data on channel A of the SCC.
- If you have a TT you may say Y here and read
- drivers/char/atari_SCC.README. All other users should say N here,
- because only the TT has SCC-DMA, even if your machine keeps claiming
- so at boot time.
-
config ATARI_MIDI
tristate "Atari MIDI serial support"
depends on ATARI
To compile this driver as a module, choose M here.
-config WHIPPET_SERIAL
- tristate "Hisoft Whippet PCMCIA serial support"
- depends on AMIGA_PCMCIA
- help
- HiSoft has a web page at <http://www.hisoft.co.uk/>, but there
- is no listing for the Whippet in their Amiga section.
-
config MULTIFACE_III_TTY
tristate "Multiface Card III serial support"
depends on AMIGA
depends on INPUT_ADBHID
default y
-config MAC_ADBKEYCODES
- bool "Support for ADB raw keycodes"
- depends on INPUT_ADBHID
- help
- This provides support for sending raw ADB keycodes to console
- devices. This is the default up to 2.4.0, but in future this may be
- phased out in favor of generic Linux keycodes. If you say Y here,
- you can dynamically switch via the
- /proc/sys/dev/mac_hid/keyboard_sends_linux_keycodes
- sysctl and with the "keyboard_sends_linux_keycodes=" kernel
- argument.
-
- If unsure, say Y here.
-
-config ADB_KEYBOARD
- bool "Support for ADB keyboard (old driver)"
- depends on MAC && !INPUT_ADBHID
- help
- This option allows you to use an ADB keyboard attached to your
- machine. Note that this disables any other (ie. PS/2) keyboard
- support, even if your machine is physically capable of using both at
- the same time.
-
- If you use an ADB keyboard (4 pin connector), say Y here.
- If you use a PS/2 keyboard (6 pin connector), say N here.
-
config HPDCA
tristate "HP DCA serial support"
depends on DIO && SERIAL_8250
config SERIAL167
bool "CD2401 support for MVME166/7 serial ports"
- depends on MVME16x && BROKEN
+ depends on MVME16x
help
This is the driver for the serial ports on the Motorola MVME166,
167, and 172 boards. Everyone using one of these boards should say
config SERIAL_CONSOLE
bool "Support for serial port console"
- depends on (AMIGA || ATARI || MAC || SUN3 || SUN3X || VME || APOLLO) && (ATARI_MFPSER=y || ATARI_SCC=y || ATARI_MIDI=y || MAC_SCC=y || AMIGA_BUILTIN_SERIAL=y || GVPIOEXT=y || MULTIFACE_III_TTY=y || SERIAL=y || MVME147_SCC || SERIAL167 || MVME162_SCC || BVME6000_SCC || DN_SERIAL)
+ depends on (AMIGA || ATARI || MAC || SUN3 || SUN3X || VME || APOLLO) && (ATARI_MFPSER=y || ATARI_MIDI=y || MAC_SCC=y || AMIGA_BUILTIN_SERIAL=y || GVPIOEXT=y || MULTIFACE_III_TTY=y || SERIAL=y || MVME147_SCC || SERIAL167 || MVME162_SCC || BVME6000_SCC || DN_SERIAL)
---help---
If you say Y here, it will be possible to use a serial port as the
system console (the system console is the device which receives all