#include <asm/nand.h>
#include <asm/dpmc.h>
#include <asm/portmux.h>
+#include <asm/bfin_sdh.h>
#include <mach/bf54x_keys.h>
#include <linux/input.h>
#include <linux/spi/ad7877.h>
/*
* Name the Board for the /proc/cpuinfo
*/
-const char bfin_board_name[] = "ADSP-BF548-EZKIT";
+const char bfin_board_name[] = "ADI BF548-EZKIT";
/*
* Driver needs to know address, irq and flag pin.
*/
#if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
-static struct resource bfin_isp1761_resources[] = {
+#include <linux/usb/isp1760.h>
+static struct resource bfin_isp1760_resources[] = {
[0] = {
- .name = "isp1761-regs",
.start = 0x2C0C0000,
.end = 0x2C0C0000 + 0xfffff,
.flags = IORESOURCE_MEM,
},
};
-static struct platform_device bfin_isp1761_device = {
- .name = "isp1761",
- .id = 0,
- .num_resources = ARRAY_SIZE(bfin_isp1761_resources),
- .resource = bfin_isp1761_resources,
+static struct isp1760_platform_data isp1760_priv = {
+ .is_isp1761 = 0,
+ .bus_width_16 = 1,
+ .port1_otg = 0,
+ .analog_oc = 0,
+ .dack_polarity_high = 0,
+ .dreq_polarity_high = 0,
};
-static struct platform_device *bfin_isp1761_devices[] = {
- &bfin_isp1761_device,
+static struct platform_device bfin_isp1760_device = {
+ .name = "isp1760-hcd",
+ .id = 0,
+ .dev = {
+ .platform_data = &isp1760_priv,
+ },
+ .num_resources = ARRAY_SIZE(bfin_isp1760_resources),
+ .resource = bfin_isp1760_resources,
};
-
-int __init bfin_isp1761_init(void)
-{
- unsigned int num_devices = ARRAY_SIZE(bfin_isp1761_devices);
-
- printk(KERN_INFO "%s(): registering device resources\n", __func__);
- set_irq_type(bfin_isp1761_resources[1].start, IRQF_TRIGGER_FALLING);
-
- return platform_add_devices(bfin_isp1761_devices, num_devices);
-}
-
-void __exit bfin_isp1761_exit(void)
-{
- platform_device_unregister(&bfin_isp1761_device);
-}
-arch_initcall(bfin_isp1761_init);
#endif
#if defined(CONFIG_FB_BF54X_LQ043) || defined(CONFIG_FB_BF54X_LQ043_MODULE)
};
#endif
+#if defined(CONFIG_JOYSTICK_BFIN_ROTARY) || defined(CONFIG_JOYSTICK_BFIN_ROTARY_MODULE)
+#include <asm/bfin_rotary.h>
+
+static struct bfin_rotary_platform_data bfin_rotary_data = {
+ /*.rotary_up_key = KEY_UP,*/
+ /*.rotary_down_key = KEY_DOWN,*/
+ .rotary_rel_code = REL_WHEEL,
+ .rotary_button_key = KEY_ENTER,
+ .debounce = 10, /* 0..17 */
+ .mode = ROT_QUAD_ENC | ROT_DEBE,
+};
+
+static struct resource bfin_rotary_resources[] = {
+ {
+ .start = IRQ_CNT,
+ .end = IRQ_CNT,
+ .flags = IORESOURCE_IRQ,
+ },
+};
+
+static struct platform_device bfin_rotary_device = {
+ .name = "bfin-rotary",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(bfin_rotary_resources),
+ .resource = bfin_rotary_resources,
+ .dev = {
+ .platform_data = &bfin_rotary_data,
+ },
+};
+#endif
+
+#if defined(CONFIG_INPUT_ADXL34X) || defined(CONFIG_INPUT_ADXL34X_MODULE)
+#include <linux/input.h>
+#include <linux/spi/adxl34x.h>
+static const struct adxl34x_platform_data adxl34x_info = {
+ .x_axis_offset = 0,
+ .y_axis_offset = 0,
+ .z_axis_offset = 0,
+ .tap_threshold = 0x31,
+ .tap_duration = 0x10,
+ .tap_latency = 0x60,
+ .tap_window = 0xF0,
+ .tap_axis_control = ADXL_TAP_X_EN | ADXL_TAP_Y_EN | ADXL_TAP_Z_EN,
+ .act_axis_control = 0xFF,
+ .activity_threshold = 5,
+ .inactivity_threshold = 3,
+ .inactivity_time = 4,
+ .free_fall_threshold = 0x7,
+ .free_fall_time = 0x20,
+ .data_rate = 0x8,
+ .data_range = ADXL_FULL_RES,
+
+ .ev_type = EV_ABS,
+ .ev_code_x = ABS_X, /* EV_REL */
+ .ev_code_y = ABS_Y, /* EV_REL */
+ .ev_code_z = ABS_Z, /* EV_REL */
+
+ .ev_code_tap_x = BTN_TOUCH, /* EV_KEY */
+ .ev_code_tap_y = BTN_TOUCH, /* EV_KEY */
+ .ev_code_tap_z = BTN_TOUCH, /* EV_KEY */
+
+/* .ev_code_ff = KEY_F,*/ /* EV_KEY */
+/* .ev_code_act_inactivity = KEY_A,*/ /* EV_KEY */
+ .power_mode = ADXL_AUTO_SLEEP | ADXL_LINK,
+ .fifo_mode = ADXL_FIFO_STREAM,
+};
+#endif
+
#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
static struct platform_device rtc_device = {
.name = "rtc-bfin",
#endif
#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
-static struct resource bfin_sir_resources[] = {
#ifdef CONFIG_BFIN_SIR0
+static struct resource bfin_sir0_resources[] = {
{
.start = 0xFFC00400,
.end = 0xFFC004FF,
.flags = IORESOURCE_MEM,
},
+ {
+ .start = IRQ_UART0_RX,
+ .end = IRQ_UART0_RX+1,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = CH_UART0_RX,
+ .end = CH_UART0_RX+1,
+ .flags = IORESOURCE_DMA,
+ },
+};
+static struct platform_device bfin_sir0_device = {
+ .name = "bfin_sir",
+ .id = 0,
+ .num_resources = ARRAY_SIZE(bfin_sir0_resources),
+ .resource = bfin_sir0_resources,
+};
#endif
#ifdef CONFIG_BFIN_SIR1
+static struct resource bfin_sir1_resources[] = {
{
.start = 0xFFC02000,
.end = 0xFFC020FF,
.flags = IORESOURCE_MEM,
},
+ {
+ .start = IRQ_UART1_RX,
+ .end = IRQ_UART1_RX+1,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = CH_UART1_RX,
+ .end = CH_UART1_RX+1,
+ .flags = IORESOURCE_DMA,
+ },
+};
+static struct platform_device bfin_sir1_device = {
+ .name = "bfin_sir",
+ .id = 1,
+ .num_resources = ARRAY_SIZE(bfin_sir1_resources),
+ .resource = bfin_sir1_resources,
+};
#endif
#ifdef CONFIG_BFIN_SIR2
+static struct resource bfin_sir2_resources[] = {
{
.start = 0xFFC02100,
.end = 0xFFC021FF,
.flags = IORESOURCE_MEM,
},
+ {
+ .start = IRQ_UART2_RX,
+ .end = IRQ_UART2_RX+1,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = CH_UART2_RX,
+ .end = CH_UART2_RX+1,
+ .flags = IORESOURCE_DMA,
+ },
+};
+static struct platform_device bfin_sir2_device = {
+ .name = "bfin_sir",
+ .id = 2,
+ .num_resources = ARRAY_SIZE(bfin_sir2_resources),
+ .resource = bfin_sir2_resources,
+};
#endif
#ifdef CONFIG_BFIN_SIR3
+static struct resource bfin_sir3_resources[] = {
{
.start = 0xFFC03100,
.end = 0xFFC031FF,
.flags = IORESOURCE_MEM,
},
-#endif
+ {
+ .start = IRQ_UART3_RX,
+ .end = IRQ_UART3_RX+1,
+ .flags = IORESOURCE_IRQ,
+ },
+ {
+ .start = CH_UART3_RX,
+ .end = CH_UART3_RX+1,
+ .flags = IORESOURCE_DMA,
+ },
};
-
-static struct platform_device bfin_sir_device = {
+static struct platform_device bfin_sir3_device = {
.name = "bfin_sir",
- .id = 0,
- .num_resources = ARRAY_SIZE(bfin_sir_resources),
- .resource = bfin_sir_resources,
+ .id = 3,
+ .num_resources = ARRAY_SIZE(bfin_sir3_resources),
+ .resource = bfin_sir3_resources,
};
#endif
+#endif
#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
+#include <linux/smsc911x.h>
+
static struct resource smsc911x_resources[] = {
{
.name = "smsc911x-memory",
.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
},
};
+
+static struct smsc911x_platform_config smsc911x_config = {
+ .flags = SMSC911X_USE_32BIT,
+ .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
+ .irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN,
+ .phy_interface = PHY_INTERFACE_MODE_MII,
+};
+
static struct platform_device smsc911x_device = {
.name = "smsc911x",
.id = 0,
.num_resources = ARRAY_SIZE(smsc911x_resources),
.resource = smsc911x_resources,
+ .dev = {
+ .platform_data = &smsc911x_config,
+ },
};
#endif
.dyn_fifo = 0,
.soft_con = 1,
.dma = 1,
- .num_eps = 7,
- .dma_channels = 7,
+ .num_eps = 8,
+ .dma_channels = 8,
.gpio_vrsel = GPIO_PE7,
};
#endif
#if defined(CONFIG_SDH_BFIN) || defined(CONFIG_SDH_BFIN_MODULE)
+
+static struct bfin_sd_host bfin_sdh_data = {
+ .dma_chan = CH_SDH,
+ .irq_int0 = IRQ_SDH_MASK0,
+ .pin_req = {P_SD_D0, P_SD_D1, P_SD_D2, P_SD_D3, P_SD_CLK, P_SD_CMD, 0},
+};
+
static struct platform_device bf54x_sdh_device = {
.name = "bfin-sdh",
.id = 0,
+ .dev = {
+ .platform_data = &bfin_sdh_data,
+ },
};
#endif
.offset = 0,
}, {
.name = "linux kernel(nor)",
- .size = 0x1C0000,
+ .size = 0x400000,
.offset = MTDPART_OFS_APPEND,
}, {
.name = "file system(nor)",
static struct resource ezkit_flash_resource = {
.start = 0x20000000,
- .end = 0x20ffffff,
+ .end = 0x21ffffff,
.flags = IORESOURCE_MEM,
};
};
#endif
+#if defined(CONFIG_INPUT_ADXL34X_SPI) || defined(CONFIG_INPUT_ADXL34X_SPI_MODULE)
+static struct bfin5xx_spi_chip spi_adxl34x_chip_info = {
+ .enable_dma = 0, /* use dma transfer with this chip*/
+ .bits_per_word = 8,
+ .cs_change_per_word = 0,
+};
+#endif
+
static struct spi_board_info bfin_spi_board_info[] __initdata = {
#if defined(CONFIG_MTD_M25P80) \
|| defined(CONFIG_MTD_M25P80_MODULE)
},
#endif
#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
-{
- .modalias = "ad7877",
- .platform_data = &bfin_ad7877_ts_info,
- .irq = IRQ_PJ11, /* newer boards (Rev 1.4+) use IRQ_PB4 */
- .max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0,
- .chip_select = 2,
- .controller_data = &spi_ad7877_chip_info,
-},
+ {
+ .modalias = "ad7877",
+ .platform_data = &bfin_ad7877_ts_info,
+ .irq = IRQ_PB4, /* old boards (<=Rev 1.3) use IRQ_PJ11 */
+ .max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0,
+ .chip_select = 2,
+ .controller_data = &spi_ad7877_chip_info,
+ },
#endif
#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
{
.controller_data = &spidev_chip_info,
},
#endif
+#if defined(CONFIG_INPUT_ADXL34X_SPI) || defined(CONFIG_INPUT_ADXL34X_SPI_MODULE)
+ {
+ .modalias = "adxl34x",
+ .platform_data = &adxl34x_info,
+ .irq = IRQ_PC5,
+ .max_speed_hz = 5000000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 1,
+ .chip_select = 2,
+ .controller_data = &spi_adxl34x_chip_info,
+ .mode = SPI_MODE_3,
+ },
+#endif
};
-
#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
/* SPI (0) */
static struct resource bfin_spi0_resource[] = {
[1] = {
.start = CH_SPI0,
.end = CH_SPI0,
+ .flags = IORESOURCE_DMA,
+ },
+ [2] = {
+ .start = IRQ_SPI0,
+ .end = IRQ_SPI0,
.flags = IORESOURCE_IRQ,
}
};
[1] = {
.start = CH_SPI1,
.end = CH_SPI1,
+ .flags = IORESOURCE_DMA,
+ },
+ [2] = {
+ .start = IRQ_SPI1,
+ .end = IRQ_SPI1,
.flags = IORESOURCE_IRQ,
}
};
#endif
#endif
-#ifdef CONFIG_I2C_BOARDINFO
static struct i2c_board_info __initdata bfin_i2c_board_info0[] = {
};
#if !defined(CONFIG_BF542) /* The BF542 only has 1 TWI */
static struct i2c_board_info __initdata bfin_i2c_board_info1[] = {
-#if defined(CONFIG_TWI_LCD) || defined(CONFIG_TWI_LCD_MODULE)
+#if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
{
I2C_BOARD_INFO("pcf8574_lcd", 0x22),
},
.irq = 212,
},
#endif
-};
+#if defined(CONFIG_INPUT_ADXL34X_I2C) || defined(CONFIG_INPUT_ADXL34X_I2C_MODULE)
+ {
+ I2C_BOARD_INFO("adxl34x", 0x53),
+ .irq = IRQ_PC5,
+ .platform_data = (void *)&adxl34x_info,
+ },
#endif
+};
#endif
#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
#endif
#if defined(CONFIG_BFIN_SIR) || defined(CONFIG_BFIN_SIR_MODULE)
- &bfin_sir_device,
+#ifdef CONFIG_BFIN_SIR0
+ &bfin_sir0_device,
+#endif
+#ifdef CONFIG_BFIN_SIR1
+ &bfin_sir1_device,
+#endif
+#ifdef CONFIG_BFIN_SIR2
+ &bfin_sir2_device,
+#endif
+#ifdef CONFIG_BFIN_SIR3
+ &bfin_sir3_device,
+#endif
#endif
#if defined(CONFIG_FB_BF54X_LQ043) || defined(CONFIG_FB_BF54X_LQ043_MODULE)
&musb_device,
#endif
+#if defined(CONFIG_USB_ISP1760_HCD) || defined(CONFIG_USB_ISP1760_HCD_MODULE)
+ &bfin_isp1760_device,
+#endif
+
#if defined(CONFIG_PATA_BF54X) || defined(CONFIG_PATA_BF54X_MODULE)
&bfin_atapi_device,
#endif
&bf54x_kpad_device,
#endif
+#if defined(CONFIG_JOYSTICK_BFIN_ROTARY) || defined(CONFIG_JOYSTICK_BFIN_ROTARY_MODULE)
+ &bfin_rotary_device,
+#endif
+
#if defined(CONFIG_I2C_BLACKFIN_TWI) || defined(CONFIG_I2C_BLACKFIN_TWI_MODULE)
&i2c_bfin_twi0_device,
#if !defined(CONFIG_BF542)
{
printk(KERN_INFO "%s(): registering device resources\n", __func__);
-#ifdef CONFIG_I2C_BOARDINFO
i2c_register_board_info(0, bfin_i2c_board_info0,
ARRAY_SIZE(bfin_i2c_board_info0));
#if !defined(CONFIG_BF542) /* The BF542 only has 1 TWI */
i2c_register_board_info(1, bfin_i2c_board_info1,
ARRAY_SIZE(bfin_i2c_board_info1));
#endif
-#endif
platform_add_devices(ezkit_devices, ARRAY_SIZE(ezkit_devices));
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff