static struct isp1760_platform_data isp1760_priv = {
.is_isp1761 = 0,
- .port1_disable = 0,
.bus_width_16 = 1,
.port1_otg = 0,
.analog_oc = 0,
#include <mach/bf54x-lq043.h>
static struct bfin_bf54xfb_mach_info bf54x_lq043_data = {
- .width = 480,
- .height = 272,
+ .width = 95,
+ .height = 54,
.xres = {480, 480, 480},
.yres = {272, 272, 272},
.bpp = {24, 24, 24},
};
#endif
+#if defined(CONFIG_INPUT_ADXL34X) || defined(CONFIG_INPUT_ADXL34X_MODULE)
+#include <linux/input.h>
+#include <linux/spi/adxl34x.h>
+static const struct adxl34x_platform_data adxl34x_info = {
+ .x_axis_offset = 0,
+ .y_axis_offset = 0,
+ .z_axis_offset = 0,
+ .tap_threshold = 0x31,
+ .tap_duration = 0x10,
+ .tap_latency = 0x60,
+ .tap_window = 0xF0,
+ .tap_axis_control = ADXL_TAP_X_EN | ADXL_TAP_Y_EN | ADXL_TAP_Z_EN,
+ .act_axis_control = 0xFF,
+ .activity_threshold = 5,
+ .inactivity_threshold = 3,
+ .inactivity_time = 4,
+ .free_fall_threshold = 0x7,
+ .free_fall_time = 0x20,
+ .data_rate = 0x8,
+ .data_range = ADXL_FULL_RES,
+
+ .ev_type = EV_ABS,
+ .ev_code_x = ABS_X, /* EV_REL */
+ .ev_code_y = ABS_Y, /* EV_REL */
+ .ev_code_z = ABS_Z, /* EV_REL */
+
+ .ev_code_tap_x = BTN_TOUCH, /* EV_KEY */
+ .ev_code_tap_y = BTN_TOUCH, /* EV_KEY */
+ .ev_code_tap_z = BTN_TOUCH, /* EV_KEY */
+
+/* .ev_code_ff = KEY_F,*/ /* EV_KEY */
+/* .ev_code_act_inactivity = KEY_A,*/ /* EV_KEY */
+ .power_mode = ADXL_AUTO_SLEEP | ADXL_LINK,
+ .fifo_mode = ADXL_FIFO_STREAM,
+};
+#endif
+
#if defined(CONFIG_RTC_DRV_BFIN) || defined(CONFIG_RTC_DRV_BFIN_MODULE)
static struct platform_device rtc_device = {
.name = "rtc-bfin",
#endif
#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
+#include <linux/smsc911x.h>
+
static struct resource smsc911x_resources[] = {
{
.name = "smsc911x-memory",
.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
},
};
+
+static struct smsc911x_platform_config smsc911x_config = {
+ .flags = SMSC911X_USE_32BIT,
+ .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
+ .irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN,
+ .phy_interface = PHY_INTERFACE_MODE_MII,
+};
+
static struct platform_device smsc911x_device = {
.name = "smsc911x",
.id = 0,
.num_resources = ARRAY_SIZE(smsc911x_resources),
.resource = smsc911x_resources,
+ .dev = {
+ .platform_data = &smsc911x_config,
+ },
};
#endif
};
#endif
+#if defined(CONFIG_INPUT_ADXL34X_SPI) || defined(CONFIG_INPUT_ADXL34X_SPI_MODULE)
+static struct bfin5xx_spi_chip spi_adxl34x_chip_info = {
+ .enable_dma = 0, /* use dma transfer with this chip*/
+ .bits_per_word = 8,
+ .cs_change_per_word = 0,
+};
+#endif
+
static struct spi_board_info bfin_spi_board_info[] __initdata = {
#if defined(CONFIG_MTD_M25P80) \
|| defined(CONFIG_MTD_M25P80_MODULE)
#if defined(CONFIG_SND_BLACKFIN_AD1836) \
|| defined(CONFIG_SND_BLACKFIN_AD1836_MODULE)
{
- .modalias = "ad1836-spi",
+ .modalias = "ad1836",
.max_speed_hz = 3125000, /* max spi clock (SCK) speed in HZ */
.bus_num = 1,
.chip_select = CONFIG_SND_BLACKFIN_SPI_PFBIT,
},
#endif
#if defined(CONFIG_TOUCHSCREEN_AD7877) || defined(CONFIG_TOUCHSCREEN_AD7877_MODULE)
-{
- .modalias = "ad7877",
- .platform_data = &bfin_ad7877_ts_info,
- .irq = IRQ_PB4, /* old boards (<=Rev 1.3) use IRQ_PJ11 */
- .max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
- .bus_num = 0,
- .chip_select = 2,
- .controller_data = &spi_ad7877_chip_info,
-},
+ {
+ .modalias = "ad7877",
+ .platform_data = &bfin_ad7877_ts_info,
+ .irq = IRQ_PB4, /* old boards (<=Rev 1.3) use IRQ_PJ11 */
+ .max_speed_hz = 12500000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 0,
+ .chip_select = 2,
+ .controller_data = &spi_ad7877_chip_info,
+ },
#endif
#if defined(CONFIG_SPI_SPIDEV) || defined(CONFIG_SPI_SPIDEV_MODULE)
{
.controller_data = &spidev_chip_info,
},
#endif
+#if defined(CONFIG_INPUT_ADXL34X_SPI) || defined(CONFIG_INPUT_ADXL34X_SPI_MODULE)
+ {
+ .modalias = "adxl34x",
+ .platform_data = &adxl34x_info,
+ .irq = IRQ_PC5,
+ .max_speed_hz = 5000000, /* max spi clock (SCK) speed in HZ */
+ .bus_num = 1,
+ .chip_select = 2,
+ .controller_data = &spi_adxl34x_chip_info,
+ .mode = SPI_MODE_3,
+ },
+#endif
};
-
#if defined(CONFIG_SPI_BFIN) || defined(CONFIG_SPI_BFIN_MODULE)
/* SPI (0) */
static struct resource bfin_spi0_resource[] = {
[1] = {
.start = CH_SPI0,
.end = CH_SPI0,
+ .flags = IORESOURCE_DMA,
+ },
+ [2] = {
+ .start = IRQ_SPI0,
+ .end = IRQ_SPI0,
.flags = IORESOURCE_IRQ,
}
};
[1] = {
.start = CH_SPI1,
.end = CH_SPI1,
+ .flags = IORESOURCE_DMA,
+ },
+ [2] = {
+ .start = IRQ_SPI1,
+ .end = IRQ_SPI1,
.flags = IORESOURCE_IRQ,
}
};
/* SPI controller data */
static struct bfin5xx_spi_master bf54x_spi_master_info0 = {
- .num_chipselect = 8,
+ .num_chipselect = 3,
.enable_dma = 1, /* master has the ability to do dma transfer */
.pin_req = {P_SPI0_SCK, P_SPI0_MISO, P_SPI0_MOSI, 0},
};
};
static struct bfin5xx_spi_master bf54x_spi_master_info1 = {
- .num_chipselect = 8,
+ .num_chipselect = 3,
.enable_dma = 1, /* master has the ability to do dma transfer */
.pin_req = {P_SPI1_SCK, P_SPI1_MISO, P_SPI1_MOSI, 0},
};
#endif
#endif
-#ifdef CONFIG_I2C_BOARDINFO
static struct i2c_board_info __initdata bfin_i2c_board_info0[] = {
};
#if !defined(CONFIG_BF542) /* The BF542 only has 1 TWI */
static struct i2c_board_info __initdata bfin_i2c_board_info1[] = {
-#if defined(CONFIG_TWI_LCD) || defined(CONFIG_TWI_LCD_MODULE)
+#if defined(CONFIG_BFIN_TWI_LCD) || defined(CONFIG_BFIN_TWI_LCD_MODULE)
{
I2C_BOARD_INFO("pcf8574_lcd", 0x22),
},
#endif
-#if defined(CONFIG_TWI_KEYPAD) || defined(CONFIG_TWI_KEYPAD_MODULE)
+#if defined(CONFIG_INPUT_PCF8574) || defined(CONFIG_INPUT_PCF8574_MODULE)
{
I2C_BOARD_INFO("pcf8574_keypad", 0x27),
.irq = 212,
},
#endif
-};
+#if defined(CONFIG_INPUT_ADXL34X_I2C) || defined(CONFIG_INPUT_ADXL34X_I2C_MODULE)
+ {
+ I2C_BOARD_INFO("adxl34x", 0x53),
+ .irq = IRQ_PC5,
+ .platform_data = (void *)&adxl34x_info,
+ },
#endif
+};
#endif
#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
{
printk(KERN_INFO "%s(): registering device resources\n", __func__);
-#ifdef CONFIG_I2C_BOARDINFO
i2c_register_board_info(0, bfin_i2c_board_info0,
ARRAY_SIZE(bfin_i2c_board_info0));
#if !defined(CONFIG_BF542) /* The BF542 only has 1 TWI */
i2c_register_board_info(1, bfin_i2c_board_info1,
ARRAY_SIZE(bfin_i2c_board_info1));
#endif
-#endif
platform_add_devices(ezkit_devices, ARRAY_SIZE(ezkit_devices));
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff