/*
- * arch/blackfin/kernel/setup.c
- *
- * Copyright 2004-2006 Analog Devices Inc.
- *
- * Enter bugs at http://blackfin.uclinux.org/
+ * Copyright 2004-2009 Analog Devices Inc.
*
* Licensed under the GPL-2 or later.
*/
#include <linux/tty.h>
#include <linux/pfn.h>
+#ifdef CONFIG_MTD_UCLINUX
+#include <linux/mtd/map.h>
#include <linux/ext2_fs.h>
#include <linux/cramfs_fs.h>
#include <linux/romfs_fs.h>
+#endif
#include <asm/cplb.h>
#include <asm/cacheflush.h>
EXPORT_SYMBOL(reserved_mem_dcache_on);
#ifdef CONFIG_MTD_UCLINUX
+extern struct map_info uclinux_ram_map;
unsigned long memory_mtd_end, memory_mtd_start, mtd_size;
unsigned long _ebss;
EXPORT_SYMBOL(memory_mtd_end);
/*
* In cache coherence emulation mode, we need to have the
* D-cache enabled before running any atomic operation which
- * might invove cache invalidation (i.e. spinlock, rwlock).
+ * might involve cache invalidation (i.e. spinlock, rwlock).
* So printk's are deferred until then.
*/
#ifdef CONFIG_BFIN_ICACHE
printk(KERN_INFO "Instruction Cache Enabled for CPU%u\n", cpu);
+ printk(KERN_INFO " External memory:"
+# ifdef CONFIG_BFIN_EXTMEM_ICACHEABLE
+ " cacheable"
+# else
+ " uncacheable"
+# endif
+ " in instruction cache\n");
+ if (L2_LENGTH)
+ printk(KERN_INFO " L2 SRAM :"
+# ifdef CONFIG_BFIN_L2_ICACHEABLE
+ " cacheable"
+# else
+ " uncacheable"
+# endif
+ " in instruction cache\n");
+
+#else
+ printk(KERN_INFO "Instruction Cache Disabled for CPU%u\n", cpu);
#endif
+
#ifdef CONFIG_BFIN_DCACHE
- printk(KERN_INFO "Data Cache Enabled for CPU%u"
-# if defined CONFIG_BFIN_WB
- " (write-back)"
-# elif defined CONFIG_BFIN_WT
- " (write-through)"
+ printk(KERN_INFO "Data Cache Enabled for CPU%u\n", cpu);
+ printk(KERN_INFO " External memory:"
+# if defined CONFIG_BFIN_EXTMEM_WRITEBACK
+ " cacheable (write-back)"
+# elif defined CONFIG_BFIN_EXTMEM_WRITETHROUGH
+ " cacheable (write-through)"
+# else
+ " uncacheable"
# endif
- "\n", cpu);
+ " in data cache\n");
+ if (L2_LENGTH)
+ printk(KERN_INFO " L2 SRAM :"
+# if defined CONFIG_BFIN_L2_WRITEBACK
+ " cacheable (write-back)"
+# elif defined CONFIG_BFIN_L2_WRITETHROUGH
+ " cacheable (write-through)"
+# else
+ " uncacheable"
+# endif
+ " in data cache\n");
+#else
+ printk(KERN_INFO "Data Cache Disabled for CPU%u\n", cpu);
#endif
}
struct blackfin_cpudata *cpudata = &per_cpu(cpu_data, cpu);
cpudata->idle = current;
- cpudata->loops_per_jiffy = loops_per_jiffy;
cpudata->imemctl = bfin_read_IMEM_CONTROL();
cpudata->dmemctl = bfin_read_DMEM_CONTROL();
}
unsigned long l1_data_b_length;
unsigned long l2_length;
- blackfin_dma_early_init();
+ early_shadow_stamp();
- l1_code_length = _etext_l1 - _stext_l1;
- if (l1_code_length > L1_CODE_LENGTH)
- panic("L1 Instruction SRAM Overflow\n");
- /* cannot complain as printk is not available as yet.
- * But we can continue booting and complain later!
+ /*
+ * due to the ALIGN(4) in the arch/blackfin/kernel/vmlinux.lds.S
+ * we know that everything about l1 text/data is nice and aligned,
+ * so copy by 4 byte chunks, and don't worry about overlapping
+ * src/dest.
+ *
+ * We can't use the dma_memcpy functions, since they can call
+ * scheduler functions which might be in L1 :( and core writes
+ * into L1 instruction cause bad access errors, so we are stuck,
+ * we are required to use DMA, but can't use the common dma
+ * functions. We can't use memcpy either - since that might be
+ * going to be in the relocated L1
*/
- /* Copy _stext_l1 to _etext_l1 to L1 instruction SRAM */
- dma_memcpy(_stext_l1, _l1_lma_start, l1_code_length);
+ blackfin_dma_early_init();
- l1_data_a_length = _sbss_l1 - _sdata_l1;
- if (l1_data_a_length > L1_DATA_A_LENGTH)
- panic("L1 Data SRAM Bank A Overflow\n");
+ /* if necessary, copy _stext_l1 to _etext_l1 to L1 instruction SRAM */
+ l1_code_length = _etext_l1 - _stext_l1;
+ if (l1_code_length)
+ early_dma_memcpy(_stext_l1, _l1_lma_start, l1_code_length);
- /* Copy _sdata_l1 to _sbss_l1 to L1 data bank A SRAM */
- dma_memcpy(_sdata_l1, _l1_lma_start + l1_code_length, l1_data_a_length);
+ /* if necessary, copy _sdata_l1 to _sbss_l1 to L1 data bank A SRAM */
+ l1_data_a_length = _sbss_l1 - _sdata_l1;
+ if (l1_data_a_length)
+ early_dma_memcpy(_sdata_l1, _l1_lma_start + l1_code_length, l1_data_a_length);
+ /* if necessary, copy _sdata_b_l1 to _sbss_b_l1 to L1 data bank B SRAM */
l1_data_b_length = _sbss_b_l1 - _sdata_b_l1;
- if (l1_data_b_length > L1_DATA_B_LENGTH)
- panic("L1 Data SRAM Bank B Overflow\n");
-
- /* Copy _sdata_b_l1 to _sbss_b_l1 to L1 data bank B SRAM */
- dma_memcpy(_sdata_b_l1, _l1_lma_start + l1_code_length +
+ if (l1_data_b_length)
+ early_dma_memcpy(_sdata_b_l1, _l1_lma_start + l1_code_length +
l1_data_a_length, l1_data_b_length);
+ early_dma_memcpy_done();
+
+ /* if necessary, copy _stext_l2 to _edata_l2 to L2 SRAM */
if (L2_LENGTH != 0) {
l2_length = _sbss_l2 - _stext_l2;
- if (l2_length > L2_LENGTH)
- panic("L2 SRAM Overflow\n");
-
- /* Copy _stext_l2 to _edata_l2 to L2 SRAM */
- dma_memcpy(_stext_l2, _l2_lma_start, l2_length);
+ if (l2_length)
+ memcpy(_stext_l2, _l2_lma_start, l2_length);
}
}
bfin_memmap.map[i].addr + bfin_memmap.map[i].size);
switch (bfin_memmap.map[i].type) {
case BFIN_MEMMAP_RAM:
- printk("(usable)\n");
- break;
+ printk(KERN_CONT "(usable)\n");
+ break;
case BFIN_MEMMAP_RESERVED:
- printk("(reserved)\n");
- break;
- default: printk("type %lu\n", bfin_memmap.map[i].type);
- break;
+ printk(KERN_CONT "(reserved)\n");
+ break;
+ default:
+ printk(KERN_CONT "type %lu\n", bfin_memmap.map[i].type);
+ break;
}
}
}
} else if (!memcmp(to, "clkin_hz=", 9)) {
to += 9;
early_init_clkin_hz(to);
+#ifdef CONFIG_EARLY_PRINTK
} else if (!memcmp(to, "earlyprintk=", 12)) {
to += 12;
setup_early_printk(to);
+#endif
} else if (!memcmp(to, "memmap=", 7)) {
to += 7;
parse_memmap(to);
#ifdef CONFIG_MTD_UCLINUX
unsigned long mtd_phys = 0;
#endif
+ unsigned long max_mem;
_rambase = (unsigned long)_stext;
_ramstart = (unsigned long)_end;
if (DMA_UNCACHED_REGION > (_ramend - _ramstart)) {
console_init();
- panic("DMA region exceeds memory limit: %lu.\n",
+ panic("DMA region exceeds memory limit: %lu.",
_ramend - _ramstart);
}
- memory_end = _ramend - DMA_UNCACHED_REGION;
+ max_mem = memory_end = _ramend - DMA_UNCACHED_REGION;
+
+#if (defined(CONFIG_BFIN_EXTMEM_ICACHEABLE) && ANOMALY_05000263)
+ /* Due to a Hardware Anomaly we need to limit the size of usable
+ * instruction memory to max 60MB, 56 if HUNT_FOR_ZERO is on
+ * 05000263 - Hardware loop corrupted when taking an ICPLB exception
+ */
+# if (defined(CONFIG_DEBUG_HUNT_FOR_ZERO))
+ if (max_mem >= 56 * 1024 * 1024)
+ max_mem = 56 * 1024 * 1024;
+# else
+ if (max_mem >= 60 * 1024 * 1024)
+ max_mem = 60 * 1024 * 1024;
+# endif /* CONFIG_DEBUG_HUNT_FOR_ZERO */
+#endif /* ANOMALY_05000263 */
+
#ifdef CONFIG_MPU
/* Round up to multiple of 4MB */
# if defined(CONFIG_ROMFS_FS)
if (((unsigned long *)mtd_phys)[0] == ROMSB_WORD0
- && ((unsigned long *)mtd_phys)[1] == ROMSB_WORD1)
+ && ((unsigned long *)mtd_phys)[1] == ROMSB_WORD1) {
mtd_size =
PAGE_ALIGN(be32_to_cpu(((unsigned long *)mtd_phys)[2]));
-# if (defined(CONFIG_BFIN_ICACHE) && ANOMALY_05000263)
- /* Due to a Hardware Anomaly we need to limit the size of usable
- * instruction memory to max 60MB, 56 if HUNT_FOR_ZERO is on
- * 05000263 - Hardware loop corrupted when taking an ICPLB exception
- */
-# if (defined(CONFIG_DEBUG_HUNT_FOR_ZERO))
- if (memory_end >= 56 * 1024 * 1024)
- memory_end = 56 * 1024 * 1024;
-# else
- if (memory_end >= 60 * 1024 * 1024)
- memory_end = 60 * 1024 * 1024;
-# endif /* CONFIG_DEBUG_HUNT_FOR_ZERO */
-# endif /* ANOMALY_05000263 */
-# endif /* CONFIG_ROMFS_FS */
- memory_end -= mtd_size;
-
- if (mtd_size == 0) {
- console_init();
- panic("Don't boot kernel without rootfs attached.\n");
+ /* ROM_FS is XIP, so if we found it, we need to limit memory */
+ if (memory_end > max_mem) {
+ pr_info("Limiting kernel memory to %liMB due to anomaly 05000263\n", max_mem >> 20);
+ memory_end = max_mem;
+ }
}
+# endif /* CONFIG_ROMFS_FS */
- /* Relocate MTD image to the top of memory after the uncached memory area */
- dma_memcpy((char *)memory_end, _end, mtd_size);
-
- memory_mtd_start = memory_end;
- _ebss = memory_mtd_start; /* define _ebss for compatible */
+ /* Since the default MTD_UCLINUX has no magic number, we just blindly
+ * read 8 past the end of the kernel's image, and look at it.
+ * When no image is attached, mtd_size is set to a random number
+ * Do some basic sanity checks before operating on things
+ */
+ if (mtd_size == 0 || memory_end <= mtd_size) {
+ pr_emerg("Could not find valid ram mtd attached.\n");
+ } else {
+ memory_end -= mtd_size;
+
+ /* Relocate MTD image to the top of memory after the uncached memory area */
+ uclinux_ram_map.phys = memory_mtd_start = memory_end;
+ uclinux_ram_map.size = mtd_size;
+ pr_info("Found mtd parition at 0x%p, (len=0x%lx), moving to 0x%p\n",
+ _end, mtd_size, (void *)memory_mtd_start);
+ dma_memcpy((void *)uclinux_ram_map.phys, _end, uclinux_ram_map.size);
+ }
#endif /* CONFIG_MTD_UCLINUX */
-#if (defined(CONFIG_BFIN_ICACHE) && ANOMALY_05000263)
- /* Due to a Hardware Anomaly we need to limit the size of usable
- * instruction memory to max 60MB, 56 if HUNT_FOR_ZERO is on
- * 05000263 - Hardware loop corrupted when taking an ICPLB exception
+ /* We need lo limit memory, since everything could have a text section
+ * of userspace in it, and expose anomaly 05000263. If the anomaly
+ * doesn't exist, or we don't need to - then dont.
*/
-#if (defined(CONFIG_DEBUG_HUNT_FOR_ZERO))
- if (memory_end >= 56 * 1024 * 1024)
- memory_end = 56 * 1024 * 1024;
-#else
- if (memory_end >= 60 * 1024 * 1024)
- memory_end = 60 * 1024 * 1024;
-#endif /* CONFIG_DEBUG_HUNT_FOR_ZERO */
- printk(KERN_NOTICE "Warning: limiting memory to %liMB due to hardware anomaly 05000263\n", memory_end >> 20);
-#endif /* ANOMALY_05000263 */
+ if (memory_end > max_mem) {
+ pr_info("Limiting kernel memory to %liMB due to anomaly 05000263\n", max_mem >> 20);
+ memory_end = max_mem;
+ }
#ifdef CONFIG_MPU
page_mask_nelts = ((_ramend >> PAGE_SHIFT) + 31) / 32;
printk(KERN_INFO "Kernel Managed Memory: %ldMB\n", _ramend >> 20);
printk(KERN_INFO "Memory map:\n"
- KERN_INFO " fixedcode = 0x%p-0x%p\n"
- KERN_INFO " text = 0x%p-0x%p\n"
- KERN_INFO " rodata = 0x%p-0x%p\n"
- KERN_INFO " bss = 0x%p-0x%p\n"
- KERN_INFO " data = 0x%p-0x%p\n"
- KERN_INFO " stack = 0x%p-0x%p\n"
- KERN_INFO " init = 0x%p-0x%p\n"
- KERN_INFO " available = 0x%p-0x%p\n"
+ " fixedcode = 0x%p-0x%p\n"
+ " text = 0x%p-0x%p\n"
+ " rodata = 0x%p-0x%p\n"
+ " bss = 0x%p-0x%p\n"
+ " data = 0x%p-0x%p\n"
+ " stack = 0x%p-0x%p\n"
+ " init = 0x%p-0x%p\n"
+ " available = 0x%p-0x%p\n"
#ifdef CONFIG_MTD_UCLINUX
- KERN_INFO " rootfs = 0x%p-0x%p\n"
+ " rootfs = 0x%p-0x%p\n"
#endif
#if DMA_UNCACHED_REGION > 0
- KERN_INFO " DMA Zone = 0x%p-0x%p\n"
+ " DMA Zone = 0x%p-0x%p\n"
#endif
, (void *)FIXED_CODE_START, (void *)FIXED_CODE_END,
_stext, _etext,
sanitize_memmap(bfin_memmap.map, &bfin_memmap.nr_map);
print_memory_map("boot memmap");
- /* intialize globals in linux/bootmem.h */
+ /* initialize globals in linux/bootmem.h */
find_min_max_pfn();
/* pfn of the last usable page frame */
if (max_pfn > memory_end >> PAGE_SHIFT)
{
unsigned long sclk, cclk;
+ enable_shadow_console();
+
+ /* Check to make sure we are running on the right processor */
+ if (unlikely(CPUID != bfin_cpuid()))
+ printk(KERN_ERR "ERROR: Not running on ADSP-%s: unknown CPUID 0x%04x Rev 0.%d\n",
+ CPU, bfin_cpuid(), bfin_revid());
+
#ifdef CONFIG_DUMMY_CONSOLE
conswitchp = &dummy_con;
#endif
memcpy(boot_command_line, command_line, COMMAND_LINE_SIZE);
boot_command_line[COMMAND_LINE_SIZE - 1] = '\0';
- /* setup memory defaults from the user config */
- physical_mem_end = 0;
- _ramend = get_mem_size() * 1024 * 1024;
-
memset(&bfin_memmap, 0, sizeof(bfin_memmap));
+ /* If the user does not specify things on the command line, use
+ * what the bootloader set things up as
+ */
+ physical_mem_end = 0;
parse_cmdline_early(&command_line[0]);
+ if (_ramend == 0)
+ _ramend = get_mem_size() * 1024 * 1024;
+
if (physical_mem_end == 0)
physical_mem_end = _ramend;
cclk = get_cclk();
sclk = get_sclk();
-#if !defined(CONFIG_BFIN_KERNEL_CLOCK)
- if (ANOMALY_05000273 && cclk == sclk)
- panic("ANOMALY 05000273, SCLK can not be same as CCLK");
-#endif
+ if ((ANOMALY_05000273 || ANOMALY_05000274) && (cclk >> 1) < sclk)
+ panic("ANOMALY 05000273 or 05000274: CCLK must be >= 2*SCLK");
#ifdef BF561_FAMILY
if (ANOMALY_05000266) {
#endif
printk(KERN_INFO "Hardware Trace ");
if (bfin_read_TBUFCTL() & 0x1)
- printk("Active ");
+ printk(KERN_CONT "Active ");
else
- printk("Off ");
+ printk(KERN_CONT "Off ");
if (bfin_read_TBUFCTL() & 0x2)
- printk("and Enabled\n");
+ printk(KERN_CONT "and Enabled\n");
else
- printk("and Disabled\n");
-
-#if defined(CONFIG_CHR_DEV_FLASH) || defined(CONFIG_BLK_DEV_FLASH)
- /* we need to initialize the Flashrom device here since we might
- * do things with flash early on in the boot
- */
- flash_probe();
-#endif
+ printk(KERN_CONT "and Disabled\n");
printk(KERN_INFO "Boot Mode: %i\n", bfin_read_SYSCR() & 0xF);
defined(CONFIG_BF538) || defined(CONFIG_BF539)
_bfin_swrst = bfin_read_SWRST();
#else
- _bfin_swrst = bfin_read_SYSCR();
+ /* Clear boot mode field */
+ _bfin_swrst = bfin_read_SYSCR() & ~0xf;
#endif
#ifdef CONFIG_DEBUG_DOUBLEFAULT_PRINT
else
printk(KERN_INFO "Compiled for ADSP-%s Rev 0.%d\n", CPU, bfin_compiled_revid());
- if (unlikely(CPUID != bfin_cpuid()))
- printk(KERN_ERR "ERROR: Not running on ADSP-%s: unknown CPUID 0x%04x Rev 0.%d\n",
- CPU, bfin_cpuid(), bfin_revid());
- else {
+ if (likely(CPUID == bfin_cpuid())) {
if (bfin_revid() != bfin_compiled_revid()) {
if (bfin_compiled_revid() == -1)
printk(KERN_ERR "Warning: Compiled for Rev none, but running on Rev %d\n",
printk(KERN_ERR "Warning: Compiled for Rev %d, but running on Rev %d\n",
bfin_compiled_revid(), bfin_revid());
if (bfin_compiled_revid() > bfin_revid())
- panic("Error: you are missing anomaly workarounds for this rev\n");
+ panic("Error: you are missing anomaly workarounds for this rev");
}
}
if (bfin_revid() < CONFIG_BF_REV_MIN || bfin_revid() > CONFIG_BF_REV_MAX)
printk(KERN_INFO "Processor Speed: %lu MHz core clock and %lu MHz System Clock\n",
cclk / 1000000, sclk / 1000000);
- if (ANOMALY_05000273 && (cclk >> 1) <= sclk)
- printk("\n\n\nANOMALY_05000273: CCLK must be >= 2*SCLK !!!\n\n\n");
-
setup_bootmem_allocator();
paging_init();
CPUID, bfin_cpuid());
seq_printf(m, "model name\t: ADSP-%s %lu(MHz CCLK) %lu(MHz SCLK) (%s)\n"
- "stepping\t: %d\n",
+ "stepping\t: %d ",
cpu, cclk/1000000, sclk/1000000,
#ifdef CONFIG_MPU
"mpu on",
#endif
revid);
- seq_printf(m, "cpu MHz\t\t: %lu.%03lu/%lu.%03lu\n",
+ if (bfin_revid() != bfin_compiled_revid()) {
+ if (bfin_compiled_revid() == -1)
+ seq_printf(m, "(Compiled for Rev none)");
+ else if (bfin_compiled_revid() == 0xffff)
+ seq_printf(m, "(Compiled for Rev any)");
+ else
+ seq_printf(m, "(Compiled for Rev %d)", bfin_compiled_revid());
+ }
+
+ seq_printf(m, "\ncpu MHz\t\t: %lu.%03lu/%lu.%03lu\n",
cclk/1000000, cclk%1000000,
sclk/1000000, sclk%1000000);
seq_printf(m, "bogomips\t: %lu.%02lu\n"
"Calibration\t: %lu loops\n",
- (cpudata->loops_per_jiffy * HZ) / 500000,
- ((cpudata->loops_per_jiffy * HZ) / 5000) % 100,
- (cpudata->loops_per_jiffy * HZ));
+ (loops_per_jiffy * HZ) / 500000,
+ ((loops_per_jiffy * HZ) / 5000) % 100,
+ (loops_per_jiffy * HZ));
/* Check Cache configutation */
switch (cpudata->dmemctl & (1 << DMC0_P | 1 << DMC1_P)) {
icache_size = 0;
seq_printf(m, "cache size\t: %d KB(L1 icache) "
- "%d KB(L1 dcache-%s) %d KB(L2 cache)\n",
- icache_size, dcache_size,
-#if defined CONFIG_BFIN_WB
- "wb"
-#elif defined CONFIG_BFIN_WT
- "wt"
-#endif
- "", 0);
-
+ "%d KB(L1 dcache) %d KB(L2 cache)\n",
+ icache_size, dcache_size, 0);
seq_printf(m, "%s\n", cache);
+ seq_printf(m, "external memory\t: "
+#if defined(CONFIG_BFIN_EXTMEM_ICACHEABLE)
+ "cacheable"
+#else
+ "uncacheable"
+#endif
+ " in instruction cache\n");
+ seq_printf(m, "external memory\t: "
+#if defined(CONFIG_BFIN_EXTMEM_WRITEBACK)
+ "cacheable (write-back)"
+#elif defined(CONFIG_BFIN_EXTMEM_WRITETHROUGH)
+ "cacheable (write-through)"
+#else
+ "uncacheable"
+#endif
+ " in data cache\n");
if (icache_size)
seq_printf(m, "icache setup\t: %d Sub-banks/%d Ways, %d Lines/Way\n",
#ifdef __ARCH_SYNC_CORE_DCACHE
seq_printf(m, "SMP Dcache Flushes\t: %lu\n\n", cpudata->dcache_invld_count);
#endif
-#ifdef CONFIG_BFIN_ICACHE_LOCK
- switch ((cpudata->imemctl >> 3) & WAYALL_L) {
- case WAY0_L:
- seq_printf(m, "Way0 Locked-Down\n");
- break;
- case WAY1_L:
- seq_printf(m, "Way1 Locked-Down\n");
- break;
- case WAY01_L:
- seq_printf(m, "Way0,Way1 Locked-Down\n");
- break;
- case WAY2_L:
- seq_printf(m, "Way2 Locked-Down\n");
- break;
- case WAY02_L:
- seq_printf(m, "Way0,Way2 Locked-Down\n");
- break;
- case WAY12_L:
- seq_printf(m, "Way1,Way2 Locked-Down\n");
- break;
- case WAY012_L:
- seq_printf(m, "Way0,Way1 & Way2 Locked-Down\n");
- break;
- case WAY3_L:
- seq_printf(m, "Way3 Locked-Down\n");
- break;
- case WAY03_L:
- seq_printf(m, "Way0,Way3 Locked-Down\n");
- break;
- case WAY13_L:
- seq_printf(m, "Way1,Way3 Locked-Down\n");
- break;
- case WAY013_L:
- seq_printf(m, "Way 0,Way1,Way3 Locked-Down\n");
- break;
- case WAY32_L:
- seq_printf(m, "Way3,Way2 Locked-Down\n");
- break;
- case WAY320_L:
- seq_printf(m, "Way3,Way2,Way0 Locked-Down\n");
- break;
- case WAY321_L:
- seq_printf(m, "Way3,Way2,Way1 Locked-Down\n");
- break;
- case WAYALL_L:
- seq_printf(m, "All Ways are locked\n");
- break;
- default:
- seq_printf(m, "No Ways are locked\n");
- }
+#ifdef __ARCH_SYNC_CORE_ICACHE
+ seq_printf(m, "SMP Icache Flushes\t: %lu\n\n", cpudata->icache_invld_count);
#endif
if (cpu_num != num_possible_cpus() - 1)
return 0;
- if (L2_LENGTH)
+ if (L2_LENGTH) {
seq_printf(m, "L2 SRAM\t\t: %dKB\n", L2_LENGTH/0x400);
+ seq_printf(m, "L2 SRAM\t\t: "
+#if defined(CONFIG_BFIN_L2_ICACHEABLE)
+ "cacheable"
+#else
+ "uncacheable"
+#endif
+ " in instruction cache\n");
+ seq_printf(m, "L2 SRAM\t\t: "
+#if defined(CONFIG_BFIN_L2_WRITEBACK)
+ "cacheable (write-back)"
+#elif defined(CONFIG_BFIN_L2_WRITETHROUGH)
+ "cacheable (write-through)"
+#else
+ "uncacheable"
+#endif
+ " in data cache\n");
+ }
seq_printf(m, "board name\t: %s\n", bfin_board_name);
seq_printf(m, "board memory\t: %ld kB (0x%p -> 0x%p)\n",
physical_mem_end >> 10, (void *)0, (void *)physical_mem_end);
void __init cmdline_init(const char *r0)
{
+ early_shadow_stamp();
if (r0)
strncpy(command_line, r0, COMMAND_LINE_SIZE);
}
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff