/*
* OMAP1510 GPIO registers
*/
-#define OMAP1510_GPIO_BASE IO_ADDRESS(0xfffce000)
+#define OMAP1510_GPIO_BASE 0xfffce000
#define OMAP1510_GPIO_DATA_INPUT 0x00
#define OMAP1510_GPIO_DATA_OUTPUT 0x04
#define OMAP1510_GPIO_DIR_CONTROL 0x08
/*
* OMAP1610 specific GPIO registers
*/
-#define OMAP1610_GPIO1_BASE IO_ADDRESS(0xfffbe400)
-#define OMAP1610_GPIO2_BASE IO_ADDRESS(0xfffbec00)
-#define OMAP1610_GPIO3_BASE IO_ADDRESS(0xfffbb400)
-#define OMAP1610_GPIO4_BASE IO_ADDRESS(0xfffbbc00)
+#define OMAP1610_GPIO1_BASE 0xfffbe400
+#define OMAP1610_GPIO2_BASE 0xfffbec00
+#define OMAP1610_GPIO3_BASE 0xfffbb400
+#define OMAP1610_GPIO4_BASE 0xfffbbc00
#define OMAP1610_GPIO_REVISION 0x0000
#define OMAP1610_GPIO_SYSCONFIG 0x0010
#define OMAP1610_GPIO_SYSSTATUS 0x0014
#define OMAP1610_GPIO_SET_DATAOUT 0x00f0
/*
- * OMAP730 specific GPIO registers
+ * OMAP7XX specific GPIO registers
*/
-#define OMAP730_GPIO1_BASE IO_ADDRESS(0xfffbc000)
-#define OMAP730_GPIO2_BASE IO_ADDRESS(0xfffbc800)
-#define OMAP730_GPIO3_BASE IO_ADDRESS(0xfffbd000)
-#define OMAP730_GPIO4_BASE IO_ADDRESS(0xfffbd800)
-#define OMAP730_GPIO5_BASE IO_ADDRESS(0xfffbe000)
-#define OMAP730_GPIO6_BASE IO_ADDRESS(0xfffbe800)
-#define OMAP730_GPIO_DATA_INPUT 0x00
-#define OMAP730_GPIO_DATA_OUTPUT 0x04
-#define OMAP730_GPIO_DIR_CONTROL 0x08
-#define OMAP730_GPIO_INT_CONTROL 0x0c
-#define OMAP730_GPIO_INT_MASK 0x10
-#define OMAP730_GPIO_INT_STATUS 0x14
-
-/*
- * OMAP850 specific GPIO registers
- */
-#define OMAP850_GPIO1_BASE IO_ADDRESS(0xfffbc000)
-#define OMAP850_GPIO2_BASE IO_ADDRESS(0xfffbc800)
-#define OMAP850_GPIO3_BASE IO_ADDRESS(0xfffbd000)
-#define OMAP850_GPIO4_BASE IO_ADDRESS(0xfffbd800)
-#define OMAP850_GPIO5_BASE IO_ADDRESS(0xfffbe000)
-#define OMAP850_GPIO6_BASE IO_ADDRESS(0xfffbe800)
-#define OMAP850_GPIO_DATA_INPUT 0x00
-#define OMAP850_GPIO_DATA_OUTPUT 0x04
-#define OMAP850_GPIO_DIR_CONTROL 0x08
-#define OMAP850_GPIO_INT_CONTROL 0x0c
-#define OMAP850_GPIO_INT_MASK 0x10
-#define OMAP850_GPIO_INT_STATUS 0x14
+#define OMAP7XX_GPIO1_BASE 0xfffbc000
+#define OMAP7XX_GPIO2_BASE 0xfffbc800
+#define OMAP7XX_GPIO3_BASE 0xfffbd000
+#define OMAP7XX_GPIO4_BASE 0xfffbd800
+#define OMAP7XX_GPIO5_BASE 0xfffbe000
+#define OMAP7XX_GPIO6_BASE 0xfffbe800
+#define OMAP7XX_GPIO_DATA_INPUT 0x00
+#define OMAP7XX_GPIO_DATA_OUTPUT 0x04
+#define OMAP7XX_GPIO_DIR_CONTROL 0x08
+#define OMAP7XX_GPIO_INT_CONTROL 0x0c
+#define OMAP7XX_GPIO_INT_MASK 0x10
+#define OMAP7XX_GPIO_INT_STATUS 0x14
+
+#define OMAP1_MPUIO_VBASE OMAP1_MPUIO_BASE
/*
* omap24xx specific GPIO registers
*/
-#define OMAP242X_GPIO1_BASE IO_ADDRESS(0x48018000)
-#define OMAP242X_GPIO2_BASE IO_ADDRESS(0x4801a000)
-#define OMAP242X_GPIO3_BASE IO_ADDRESS(0x4801c000)
-#define OMAP242X_GPIO4_BASE IO_ADDRESS(0x4801e000)
+#define OMAP242X_GPIO1_BASE 0x48018000
+#define OMAP242X_GPIO2_BASE 0x4801a000
+#define OMAP242X_GPIO3_BASE 0x4801c000
+#define OMAP242X_GPIO4_BASE 0x4801e000
-#define OMAP243X_GPIO1_BASE IO_ADDRESS(0x4900C000)
-#define OMAP243X_GPIO2_BASE IO_ADDRESS(0x4900E000)
-#define OMAP243X_GPIO3_BASE IO_ADDRESS(0x49010000)
-#define OMAP243X_GPIO4_BASE IO_ADDRESS(0x49012000)
-#define OMAP243X_GPIO5_BASE IO_ADDRESS(0x480B6000)
+#define OMAP243X_GPIO1_BASE 0x4900C000
+#define OMAP243X_GPIO2_BASE 0x4900E000
+#define OMAP243X_GPIO3_BASE 0x49010000
+#define OMAP243X_GPIO4_BASE 0x49012000
+#define OMAP243X_GPIO5_BASE 0x480B6000
#define OMAP24XX_GPIO_REVISION 0x0000
#define OMAP24XX_GPIO_SYSCONFIG 0x0010
#define OMAP24XX_GPIO_CLEARDATAOUT 0x0090
#define OMAP24XX_GPIO_SETDATAOUT 0x0094
+#define OMAP4_GPIO_REVISION 0x0000
+#define OMAP4_GPIO_SYSCONFIG 0x0010
+#define OMAP4_GPIO_EOI 0x0020
+#define OMAP4_GPIO_IRQSTATUSRAW0 0x0024
+#define OMAP4_GPIO_IRQSTATUSRAW1 0x0028
+#define OMAP4_GPIO_IRQSTATUS0 0x002c
+#define OMAP4_GPIO_IRQSTATUS1 0x0030
+#define OMAP4_GPIO_IRQSTATUSSET0 0x0034
+#define OMAP4_GPIO_IRQSTATUSSET1 0x0038
+#define OMAP4_GPIO_IRQSTATUSCLR0 0x003c
+#define OMAP4_GPIO_IRQSTATUSCLR1 0x0040
+#define OMAP4_GPIO_IRQWAKEN0 0x0044
+#define OMAP4_GPIO_IRQWAKEN1 0x0048
+#define OMAP4_GPIO_SYSSTATUS 0x0104
+#define OMAP4_GPIO_CTRL 0x0130
+#define OMAP4_GPIO_OE 0x0134
+#define OMAP4_GPIO_DATAIN 0x0138
+#define OMAP4_GPIO_DATAOUT 0x013c
+#define OMAP4_GPIO_LEVELDETECT0 0x0140
+#define OMAP4_GPIO_LEVELDETECT1 0x0144
+#define OMAP4_GPIO_RISINGDETECT 0x0148
+#define OMAP4_GPIO_FALLINGDETECT 0x014c
+#define OMAP4_GPIO_DEBOUNCENABLE 0x0150
+#define OMAP4_GPIO_DEBOUNCINGTIME 0x0154
+#define OMAP4_GPIO_CLEARDATAOUT 0x0190
+#define OMAP4_GPIO_SETDATAOUT 0x0194
/*
* omap34xx specific GPIO registers
*/
-#define OMAP34XX_GPIO1_BASE IO_ADDRESS(0x48310000)
-#define OMAP34XX_GPIO2_BASE IO_ADDRESS(0x49050000)
-#define OMAP34XX_GPIO3_BASE IO_ADDRESS(0x49052000)
-#define OMAP34XX_GPIO4_BASE IO_ADDRESS(0x49054000)
-#define OMAP34XX_GPIO5_BASE IO_ADDRESS(0x49056000)
-#define OMAP34XX_GPIO6_BASE IO_ADDRESS(0x49058000)
+#define OMAP34XX_GPIO1_BASE 0x48310000
+#define OMAP34XX_GPIO2_BASE 0x49050000
+#define OMAP34XX_GPIO3_BASE 0x49052000
+#define OMAP34XX_GPIO4_BASE 0x49054000
+#define OMAP34XX_GPIO5_BASE 0x49056000
+#define OMAP34XX_GPIO6_BASE 0x49058000
/*
* OMAP44XX specific GPIO registers
*/
-#define OMAP44XX_GPIO1_BASE IO_ADDRESS(0x4a310000)
-#define OMAP44XX_GPIO2_BASE IO_ADDRESS(0x48055000)
-#define OMAP44XX_GPIO3_BASE IO_ADDRESS(0x48057000)
-#define OMAP44XX_GPIO4_BASE IO_ADDRESS(0x48059000)
-#define OMAP44XX_GPIO5_BASE IO_ADDRESS(0x4805B000)
-#define OMAP44XX_GPIO6_BASE IO_ADDRESS(0x4805D000)
-
-#define OMAP_MPUIO_VBASE IO_ADDRESS(OMAP_MPUIO_BASE)
+#define OMAP44XX_GPIO1_BASE 0x4a310000
+#define OMAP44XX_GPIO2_BASE 0x48055000
+#define OMAP44XX_GPIO3_BASE 0x48057000
+#define OMAP44XX_GPIO4_BASE 0x48059000
+#define OMAP44XX_GPIO5_BASE 0x4805B000
+#define OMAP44XX_GPIO6_BASE 0x4805D000
struct gpio_bank {
+ unsigned long pbase;
void __iomem *base;
u16 irq;
u16 virtual_irq_start;
int method;
-#if defined(CONFIG_ARCH_OMAP16XX) || defined(CONFIG_ARCH_OMAP24XX) || \
- defined(CONFIG_ARCH_OMAP34XX) || defined(CONFIG_ARCH_OMAP4)
+#if defined(CONFIG_ARCH_OMAP16XX) || defined(CONFIG_ARCH_OMAP2PLUS)
u32 suspend_wakeup;
u32 saved_wakeup;
#endif
-#if defined(CONFIG_ARCH_OMAP24XX) || defined(CONFIG_ARCH_OMAP34XX) || \
- defined(CONFIG_ARCH_OMAP4)
+#ifdef CONFIG_ARCH_OMAP2PLUS
u32 non_wakeup_gpios;
u32 enabled_non_wakeup_gpios;
u32 saved_risingdetect;
#endif
u32 level_mask;
+ u32 toggle_mask;
spinlock_t lock;
struct gpio_chip chip;
struct clk *dbck;
+ u32 mod_usage;
};
#define METHOD_MPUIO 0
#define METHOD_GPIO_1510 1
#define METHOD_GPIO_1610 2
-#define METHOD_GPIO_730 3
-#define METHOD_GPIO_850 4
+#define METHOD_GPIO_7XX 3
#define METHOD_GPIO_24XX 5
+#define METHOD_GPIO_44XX 6
#ifdef CONFIG_ARCH_OMAP16XX
static struct gpio_bank gpio_bank_1610[5] = {
- { OMAP_MPUIO_VBASE, INT_MPUIO, IH_MPUIO_BASE, METHOD_MPUIO},
- { OMAP1610_GPIO1_BASE, INT_GPIO_BANK1, IH_GPIO_BASE, METHOD_GPIO_1610 },
- { OMAP1610_GPIO2_BASE, INT_1610_GPIO_BANK2, IH_GPIO_BASE + 16, METHOD_GPIO_1610 },
- { OMAP1610_GPIO3_BASE, INT_1610_GPIO_BANK3, IH_GPIO_BASE + 32, METHOD_GPIO_1610 },
- { OMAP1610_GPIO4_BASE, INT_1610_GPIO_BANK4, IH_GPIO_BASE + 48, METHOD_GPIO_1610 },
+ { OMAP1_MPUIO_VBASE, NULL, INT_MPUIO, IH_MPUIO_BASE,
+ METHOD_MPUIO },
+ { OMAP1610_GPIO1_BASE, NULL, INT_GPIO_BANK1, IH_GPIO_BASE,
+ METHOD_GPIO_1610 },
+ { OMAP1610_GPIO2_BASE, NULL, INT_1610_GPIO_BANK2, IH_GPIO_BASE + 16,
+ METHOD_GPIO_1610 },
+ { OMAP1610_GPIO3_BASE, NULL, INT_1610_GPIO_BANK3, IH_GPIO_BASE + 32,
+ METHOD_GPIO_1610 },
+ { OMAP1610_GPIO4_BASE, NULL, INT_1610_GPIO_BANK4, IH_GPIO_BASE + 48,
+ METHOD_GPIO_1610 },
};
#endif
#ifdef CONFIG_ARCH_OMAP15XX
static struct gpio_bank gpio_bank_1510[2] = {
- { OMAP_MPUIO_VBASE, INT_MPUIO, IH_MPUIO_BASE, METHOD_MPUIO },
- { OMAP1510_GPIO_BASE, INT_GPIO_BANK1, IH_GPIO_BASE, METHOD_GPIO_1510 }
+ { OMAP1_MPUIO_VBASE, NULL, INT_MPUIO, IH_MPUIO_BASE,
+ METHOD_MPUIO },
+ { OMAP1510_GPIO_BASE, NULL, INT_GPIO_BANK1, IH_GPIO_BASE,
+ METHOD_GPIO_1510 }
};
#endif
-#ifdef CONFIG_ARCH_OMAP730
-static struct gpio_bank gpio_bank_730[7] = {
- { OMAP_MPUIO_VBASE, INT_730_MPUIO, IH_MPUIO_BASE, METHOD_MPUIO },
- { OMAP730_GPIO1_BASE, INT_730_GPIO_BANK1, IH_GPIO_BASE, METHOD_GPIO_730 },
- { OMAP730_GPIO2_BASE, INT_730_GPIO_BANK2, IH_GPIO_BASE + 32, METHOD_GPIO_730 },
- { OMAP730_GPIO3_BASE, INT_730_GPIO_BANK3, IH_GPIO_BASE + 64, METHOD_GPIO_730 },
- { OMAP730_GPIO4_BASE, INT_730_GPIO_BANK4, IH_GPIO_BASE + 96, METHOD_GPIO_730 },
- { OMAP730_GPIO5_BASE, INT_730_GPIO_BANK5, IH_GPIO_BASE + 128, METHOD_GPIO_730 },
- { OMAP730_GPIO6_BASE, INT_730_GPIO_BANK6, IH_GPIO_BASE + 160, METHOD_GPIO_730 },
+#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
+static struct gpio_bank gpio_bank_7xx[7] = {
+ { OMAP1_MPUIO_VBASE, NULL, INT_7XX_MPUIO, IH_MPUIO_BASE,
+ METHOD_MPUIO },
+ { OMAP7XX_GPIO1_BASE, NULL, INT_7XX_GPIO_BANK1, IH_GPIO_BASE,
+ METHOD_GPIO_7XX },
+ { OMAP7XX_GPIO2_BASE, NULL, INT_7XX_GPIO_BANK2, IH_GPIO_BASE + 32,
+ METHOD_GPIO_7XX },
+ { OMAP7XX_GPIO3_BASE, NULL, INT_7XX_GPIO_BANK3, IH_GPIO_BASE + 64,
+ METHOD_GPIO_7XX },
+ { OMAP7XX_GPIO4_BASE, NULL, INT_7XX_GPIO_BANK4, IH_GPIO_BASE + 96,
+ METHOD_GPIO_7XX },
+ { OMAP7XX_GPIO5_BASE, NULL, INT_7XX_GPIO_BANK5, IH_GPIO_BASE + 128,
+ METHOD_GPIO_7XX },
+ { OMAP7XX_GPIO6_BASE, NULL, INT_7XX_GPIO_BANK6, IH_GPIO_BASE + 160,
+ METHOD_GPIO_7XX },
};
#endif
-#ifdef CONFIG_ARCH_OMAP850
-static struct gpio_bank gpio_bank_850[7] = {
- { OMAP_MPUIO_BASE, INT_850_MPUIO, IH_MPUIO_BASE, METHOD_MPUIO },
- { OMAP850_GPIO1_BASE, INT_850_GPIO_BANK1, IH_GPIO_BASE, METHOD_GPIO_850 },
- { OMAP850_GPIO2_BASE, INT_850_GPIO_BANK2, IH_GPIO_BASE + 32, METHOD_GPIO_850 },
- { OMAP850_GPIO3_BASE, INT_850_GPIO_BANK3, IH_GPIO_BASE + 64, METHOD_GPIO_850 },
- { OMAP850_GPIO4_BASE, INT_850_GPIO_BANK4, IH_GPIO_BASE + 96, METHOD_GPIO_850 },
- { OMAP850_GPIO5_BASE, INT_850_GPIO_BANK5, IH_GPIO_BASE + 128, METHOD_GPIO_850 },
- { OMAP850_GPIO6_BASE, INT_850_GPIO_BANK6, IH_GPIO_BASE + 160, METHOD_GPIO_850 },
-};
-#endif
-
-
-#ifdef CONFIG_ARCH_OMAP24XX
+#ifdef CONFIG_ARCH_OMAP2
static struct gpio_bank gpio_bank_242x[4] = {
- { OMAP242X_GPIO1_BASE, INT_24XX_GPIO_BANK1, IH_GPIO_BASE, METHOD_GPIO_24XX },
- { OMAP242X_GPIO2_BASE, INT_24XX_GPIO_BANK2, IH_GPIO_BASE + 32, METHOD_GPIO_24XX },
- { OMAP242X_GPIO3_BASE, INT_24XX_GPIO_BANK3, IH_GPIO_BASE + 64, METHOD_GPIO_24XX },
- { OMAP242X_GPIO4_BASE, INT_24XX_GPIO_BANK4, IH_GPIO_BASE + 96, METHOD_GPIO_24XX },
+ { OMAP242X_GPIO1_BASE, NULL, INT_24XX_GPIO_BANK1, IH_GPIO_BASE,
+ METHOD_GPIO_24XX },
+ { OMAP242X_GPIO2_BASE, NULL, INT_24XX_GPIO_BANK2, IH_GPIO_BASE + 32,
+ METHOD_GPIO_24XX },
+ { OMAP242X_GPIO3_BASE, NULL, INT_24XX_GPIO_BANK3, IH_GPIO_BASE + 64,
+ METHOD_GPIO_24XX },
+ { OMAP242X_GPIO4_BASE, NULL, INT_24XX_GPIO_BANK4, IH_GPIO_BASE + 96,
+ METHOD_GPIO_24XX },
};
static struct gpio_bank gpio_bank_243x[5] = {
- { OMAP243X_GPIO1_BASE, INT_24XX_GPIO_BANK1, IH_GPIO_BASE, METHOD_GPIO_24XX },
- { OMAP243X_GPIO2_BASE, INT_24XX_GPIO_BANK2, IH_GPIO_BASE + 32, METHOD_GPIO_24XX },
- { OMAP243X_GPIO3_BASE, INT_24XX_GPIO_BANK3, IH_GPIO_BASE + 64, METHOD_GPIO_24XX },
- { OMAP243X_GPIO4_BASE, INT_24XX_GPIO_BANK4, IH_GPIO_BASE + 96, METHOD_GPIO_24XX },
- { OMAP243X_GPIO5_BASE, INT_24XX_GPIO_BANK5, IH_GPIO_BASE + 128, METHOD_GPIO_24XX },
+ { OMAP243X_GPIO1_BASE, NULL, INT_24XX_GPIO_BANK1, IH_GPIO_BASE,
+ METHOD_GPIO_24XX },
+ { OMAP243X_GPIO2_BASE, NULL, INT_24XX_GPIO_BANK2, IH_GPIO_BASE + 32,
+ METHOD_GPIO_24XX },
+ { OMAP243X_GPIO3_BASE, NULL, INT_24XX_GPIO_BANK3, IH_GPIO_BASE + 64,
+ METHOD_GPIO_24XX },
+ { OMAP243X_GPIO4_BASE, NULL, INT_24XX_GPIO_BANK4, IH_GPIO_BASE + 96,
+ METHOD_GPIO_24XX },
+ { OMAP243X_GPIO5_BASE, NULL, INT_24XX_GPIO_BANK5, IH_GPIO_BASE + 128,
+ METHOD_GPIO_24XX },
};
#endif
-#ifdef CONFIG_ARCH_OMAP34XX
+#ifdef CONFIG_ARCH_OMAP3
static struct gpio_bank gpio_bank_34xx[6] = {
- { OMAP34XX_GPIO1_BASE, INT_34XX_GPIO_BANK1, IH_GPIO_BASE, METHOD_GPIO_24XX },
- { OMAP34XX_GPIO2_BASE, INT_34XX_GPIO_BANK2, IH_GPIO_BASE + 32, METHOD_GPIO_24XX },
- { OMAP34XX_GPIO3_BASE, INT_34XX_GPIO_BANK3, IH_GPIO_BASE + 64, METHOD_GPIO_24XX },
- { OMAP34XX_GPIO4_BASE, INT_34XX_GPIO_BANK4, IH_GPIO_BASE + 96, METHOD_GPIO_24XX },
- { OMAP34XX_GPIO5_BASE, INT_34XX_GPIO_BANK5, IH_GPIO_BASE + 128, METHOD_GPIO_24XX },
- { OMAP34XX_GPIO6_BASE, INT_34XX_GPIO_BANK6, IH_GPIO_BASE + 160, METHOD_GPIO_24XX },
-};
-
-#endif
-
-#ifdef CONFIG_ARCH_OMAP4
-static struct gpio_bank gpio_bank_44xx[6] = {
- { OMAP44XX_GPIO1_BASE, INT_44XX_GPIO_BANK1, IH_GPIO_BASE, \
+ { OMAP34XX_GPIO1_BASE, NULL, INT_34XX_GPIO_BANK1, IH_GPIO_BASE,
METHOD_GPIO_24XX },
- { OMAP44XX_GPIO2_BASE, INT_44XX_GPIO_BANK2, IH_GPIO_BASE + 32, \
+ { OMAP34XX_GPIO2_BASE, NULL, INT_34XX_GPIO_BANK2, IH_GPIO_BASE + 32,
METHOD_GPIO_24XX },
- { OMAP44XX_GPIO3_BASE, INT_44XX_GPIO_BANK3, IH_GPIO_BASE + 64, \
+ { OMAP34XX_GPIO3_BASE, NULL, INT_34XX_GPIO_BANK3, IH_GPIO_BASE + 64,
METHOD_GPIO_24XX },
- { OMAP44XX_GPIO4_BASE, INT_44XX_GPIO_BANK4, IH_GPIO_BASE + 96, \
+ { OMAP34XX_GPIO4_BASE, NULL, INT_34XX_GPIO_BANK4, IH_GPIO_BASE + 96,
METHOD_GPIO_24XX },
- { OMAP44XX_GPIO5_BASE, INT_44XX_GPIO_BANK5, IH_GPIO_BASE + 128, \
+ { OMAP34XX_GPIO5_BASE, NULL, INT_34XX_GPIO_BANK5, IH_GPIO_BASE + 128,
METHOD_GPIO_24XX },
- { OMAP44XX_GPIO6_BASE, INT_44XX_GPIO_BANK6, IH_GPIO_BASE + 160, \
+ { OMAP34XX_GPIO6_BASE, NULL, INT_34XX_GPIO_BANK6, IH_GPIO_BASE + 160,
METHOD_GPIO_24XX },
};
+struct omap3_gpio_regs {
+ u32 sysconfig;
+ u32 irqenable1;
+ u32 irqenable2;
+ u32 wake_en;
+ u32 ctrl;
+ u32 oe;
+ u32 leveldetect0;
+ u32 leveldetect1;
+ u32 risingdetect;
+ u32 fallingdetect;
+ u32 dataout;
+ u32 setwkuena;
+ u32 setdataout;
+};
+
+static struct omap3_gpio_regs gpio_context[OMAP34XX_NR_GPIOS];
+#endif
+
+#ifdef CONFIG_ARCH_OMAP4
+static struct gpio_bank gpio_bank_44xx[6] = {
+ { OMAP44XX_GPIO1_BASE, NULL, OMAP44XX_IRQ_GPIO1, IH_GPIO_BASE,
+ METHOD_GPIO_44XX },
+ { OMAP44XX_GPIO2_BASE, NULL, OMAP44XX_IRQ_GPIO2, IH_GPIO_BASE + 32,
+ METHOD_GPIO_44XX },
+ { OMAP44XX_GPIO3_BASE, NULL, OMAP44XX_IRQ_GPIO3, IH_GPIO_BASE + 64,
+ METHOD_GPIO_44XX },
+ { OMAP44XX_GPIO4_BASE, NULL, OMAP44XX_IRQ_GPIO4, IH_GPIO_BASE + 96,
+ METHOD_GPIO_44XX },
+ { OMAP44XX_GPIO5_BASE, NULL, OMAP44XX_IRQ_GPIO5, IH_GPIO_BASE + 128,
+ METHOD_GPIO_44XX },
+ { OMAP44XX_GPIO6_BASE, NULL, OMAP44XX_IRQ_GPIO6, IH_GPIO_BASE + 160,
+ METHOD_GPIO_44XX },
+};
+
#endif
static struct gpio_bank *gpio_bank;
static int check_gpio(int gpio)
{
- if (unlikely(gpio_valid(gpio)) < 0) {
+ if (unlikely(gpio_valid(gpio) < 0)) {
printk(KERN_ERR "omap-gpio: invalid GPIO %d\n", gpio);
dump_stack();
return -1;
reg += OMAP1610_GPIO_DIRECTION;
break;
#endif
-#ifdef CONFIG_ARCH_OMAP730
- case METHOD_GPIO_730:
- reg += OMAP730_GPIO_DIR_CONTROL;
+#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
+ case METHOD_GPIO_7XX:
+ reg += OMAP7XX_GPIO_DIR_CONTROL;
break;
#endif
-#ifdef CONFIG_ARCH_OMAP850
- case METHOD_GPIO_850:
- reg += OMAP850_GPIO_DIR_CONTROL;
- break;
-#endif
-#if defined(CONFIG_ARCH_OMAP24XX) || defined(CONFIG_ARCH_OMAP34XX) || \
- defined(CONFIG_ARCH_OMAP4)
+#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3)
case METHOD_GPIO_24XX:
reg += OMAP24XX_GPIO_OE;
break;
#endif
+#if defined(CONFIG_ARCH_OMAP4)
+ case METHOD_GPIO_44XX:
+ reg += OMAP4_GPIO_OE;
+ break;
+#endif
default:
WARN_ON(1);
return;
l = 1 << gpio;
break;
#endif
-#ifdef CONFIG_ARCH_OMAP730
- case METHOD_GPIO_730:
- reg += OMAP730_GPIO_DATA_OUTPUT;
+#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
+ case METHOD_GPIO_7XX:
+ reg += OMAP7XX_GPIO_DATA_OUTPUT;
l = __raw_readl(reg);
if (enable)
l |= 1 << gpio;
l &= ~(1 << gpio);
break;
#endif
-#ifdef CONFIG_ARCH_OMAP850
- case METHOD_GPIO_850:
- reg += OMAP850_GPIO_DATA_OUTPUT;
- l = __raw_readl(reg);
+#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3)
+ case METHOD_GPIO_24XX:
if (enable)
- l |= 1 << gpio;
+ reg += OMAP24XX_GPIO_SETDATAOUT;
else
- l &= ~(1 << gpio);
+ reg += OMAP24XX_GPIO_CLEARDATAOUT;
+ l = 1 << gpio;
break;
#endif
-#if defined(CONFIG_ARCH_OMAP24XX) || defined(CONFIG_ARCH_OMAP34XX) || \
- defined(CONFIG_ARCH_OMAP4)
- case METHOD_GPIO_24XX:
+#ifdef CONFIG_ARCH_OMAP4
+ case METHOD_GPIO_44XX:
if (enable)
- reg += OMAP24XX_GPIO_SETDATAOUT;
+ reg += OMAP4_GPIO_SETDATAOUT;
else
- reg += OMAP24XX_GPIO_CLEARDATAOUT;
+ reg += OMAP4_GPIO_CLEARDATAOUT;
l = 1 << gpio;
break;
#endif
__raw_writel(l, reg);
}
-static int __omap_get_gpio_datain(int gpio)
+static int _get_gpio_datain(struct gpio_bank *bank, int gpio)
{
- struct gpio_bank *bank;
void __iomem *reg;
if (check_gpio(gpio) < 0)
return -EINVAL;
- bank = get_gpio_bank(gpio);
reg = bank->base;
switch (bank->method) {
#ifdef CONFIG_ARCH_OMAP1
reg += OMAP1610_GPIO_DATAIN;
break;
#endif
-#ifdef CONFIG_ARCH_OMAP730
- case METHOD_GPIO_730:
- reg += OMAP730_GPIO_DATA_INPUT;
+#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
+ case METHOD_GPIO_7XX:
+ reg += OMAP7XX_GPIO_DATA_INPUT;
break;
#endif
-#ifdef CONFIG_ARCH_OMAP850
- case METHOD_GPIO_850:
- reg += OMAP850_GPIO_DATA_INPUT;
- break;
-#endif
-#if defined(CONFIG_ARCH_OMAP24XX) || defined(CONFIG_ARCH_OMAP34XX) || \
- defined(CONFIG_ARCH_OMAP4)
+#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3)
case METHOD_GPIO_24XX:
reg += OMAP24XX_GPIO_DATAIN;
break;
#endif
+#ifdef CONFIG_ARCH_OMAP4
+ case METHOD_GPIO_44XX:
+ reg += OMAP4_GPIO_DATAIN;
+ break;
+#endif
default:
return -EINVAL;
}
& (1 << get_gpio_index(gpio))) != 0;
}
+static int _get_gpio_dataout(struct gpio_bank *bank, int gpio)
+{
+ void __iomem *reg;
+
+ if (check_gpio(gpio) < 0)
+ return -EINVAL;
+ reg = bank->base;
+
+ switch (bank->method) {
+#ifdef CONFIG_ARCH_OMAP1
+ case METHOD_MPUIO:
+ reg += OMAP_MPUIO_OUTPUT;
+ break;
+#endif
+#ifdef CONFIG_ARCH_OMAP15XX
+ case METHOD_GPIO_1510:
+ reg += OMAP1510_GPIO_DATA_OUTPUT;
+ break;
+#endif
+#ifdef CONFIG_ARCH_OMAP16XX
+ case METHOD_GPIO_1610:
+ reg += OMAP1610_GPIO_DATAOUT;
+ break;
+#endif
+#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
+ case METHOD_GPIO_7XX:
+ reg += OMAP7XX_GPIO_DATA_OUTPUT;
+ break;
+#endif
+#ifdef CONFIG_ARCH_OMAP2PLUS
+ case METHOD_GPIO_24XX:
+ case METHOD_GPIO_44XX:
+ reg += OMAP24XX_GPIO_DATAOUT;
+ break;
+#endif
+ default:
+ return -EINVAL;
+ }
+
+ return (__raw_readl(reg) & (1 << get_gpio_index(gpio))) != 0;
+}
+
#define MOD_REG_BIT(reg, bit_mask, set) \
do { \
int l = __raw_readl(base + reg); \
bank = get_gpio_bank(gpio);
reg = bank->base;
- reg += OMAP24XX_GPIO_DEBOUNCE_EN;
+
+ if (cpu_is_omap44xx())
+ reg += OMAP4_GPIO_DEBOUNCENABLE;
+ else
+ reg += OMAP24XX_GPIO_DEBOUNCE_EN;
+
+ if (!(bank->mod_usage & l)) {
+ printk(KERN_ERR "GPIO %d not requested\n", gpio);
+ return;
+ }
spin_lock_irqsave(&bank->lock, flags);
val = __raw_readl(reg);
bank = get_gpio_bank(gpio);
reg = bank->base;
+ if (!bank->mod_usage) {
+ printk(KERN_ERR "GPIO not requested\n");
+ return;
+ }
+
enc_time &= 0xff;
- reg += OMAP24XX_GPIO_DEBOUNCE_VAL;
+
+ if (cpu_is_omap44xx())
+ reg += OMAP4_GPIO_DEBOUNCINGTIME;
+ else
+ reg += OMAP24XX_GPIO_DEBOUNCE_VAL;
+
__raw_writel(enc_time, reg);
}
EXPORT_SYMBOL(omap_set_gpio_debounce_time);
-#if defined(CONFIG_ARCH_OMAP24XX) || defined(CONFIG_ARCH_OMAP34XX) || \
- defined(CONFIG_ARCH_OMAP4)
+#ifdef CONFIG_ARCH_OMAP2PLUS
static inline void set_24xx_gpio_triggering(struct gpio_bank *bank, int gpio,
int trigger)
{
void __iomem *base = bank->base;
u32 gpio_bit = 1 << gpio;
+ u32 val;
- MOD_REG_BIT(OMAP24XX_GPIO_LEVELDETECT0, gpio_bit,
- trigger & IRQ_TYPE_LEVEL_LOW);
- MOD_REG_BIT(OMAP24XX_GPIO_LEVELDETECT1, gpio_bit,
- trigger & IRQ_TYPE_LEVEL_HIGH);
- MOD_REG_BIT(OMAP24XX_GPIO_RISINGDETECT, gpio_bit,
- trigger & IRQ_TYPE_EDGE_RISING);
- MOD_REG_BIT(OMAP24XX_GPIO_FALLINGDETECT, gpio_bit,
- trigger & IRQ_TYPE_EDGE_FALLING);
-
+ if (cpu_is_omap44xx()) {
+ MOD_REG_BIT(OMAP4_GPIO_LEVELDETECT0, gpio_bit,
+ trigger & IRQ_TYPE_LEVEL_LOW);
+ MOD_REG_BIT(OMAP4_GPIO_LEVELDETECT1, gpio_bit,
+ trigger & IRQ_TYPE_LEVEL_HIGH);
+ MOD_REG_BIT(OMAP4_GPIO_RISINGDETECT, gpio_bit,
+ trigger & IRQ_TYPE_EDGE_RISING);
+ MOD_REG_BIT(OMAP4_GPIO_FALLINGDETECT, gpio_bit,
+ trigger & IRQ_TYPE_EDGE_FALLING);
+ } else {
+ MOD_REG_BIT(OMAP24XX_GPIO_LEVELDETECT0, gpio_bit,
+ trigger & IRQ_TYPE_LEVEL_LOW);
+ MOD_REG_BIT(OMAP24XX_GPIO_LEVELDETECT1, gpio_bit,
+ trigger & IRQ_TYPE_LEVEL_HIGH);
+ MOD_REG_BIT(OMAP24XX_GPIO_RISINGDETECT, gpio_bit,
+ trigger & IRQ_TYPE_EDGE_RISING);
+ MOD_REG_BIT(OMAP24XX_GPIO_FALLINGDETECT, gpio_bit,
+ trigger & IRQ_TYPE_EDGE_FALLING);
+ }
if (likely(!(bank->non_wakeup_gpios & gpio_bit))) {
- if (trigger != 0)
- __raw_writel(1 << gpio, bank->base
+ if (cpu_is_omap44xx()) {
+ if (trigger != 0)
+ __raw_writel(1 << gpio, bank->base+
+ OMAP4_GPIO_IRQWAKEN0);
+ else {
+ val = __raw_readl(bank->base +
+ OMAP4_GPIO_IRQWAKEN0);
+ __raw_writel(val & (~(1 << gpio)), bank->base +
+ OMAP4_GPIO_IRQWAKEN0);
+ }
+ } else {
+ if (trigger != 0)
+ __raw_writel(1 << gpio, bank->base
+ OMAP24XX_GPIO_SETWKUENA);
- else
- __raw_writel(1 << gpio, bank->base
+ else
+ __raw_writel(1 << gpio, bank->base
+ OMAP24XX_GPIO_CLEARWKUENA);
+ }
} else {
if (trigger != 0)
bank->enabled_non_wakeup_gpios |= gpio_bit;
bank->enabled_non_wakeup_gpios &= ~gpio_bit;
}
- bank->level_mask =
- __raw_readl(bank->base + OMAP24XX_GPIO_LEVELDETECT0) |
- __raw_readl(bank->base + OMAP24XX_GPIO_LEVELDETECT1);
+ if (cpu_is_omap44xx()) {
+ bank->level_mask =
+ __raw_readl(bank->base + OMAP4_GPIO_LEVELDETECT0) |
+ __raw_readl(bank->base + OMAP4_GPIO_LEVELDETECT1);
+ } else {
+ bank->level_mask =
+ __raw_readl(bank->base + OMAP24XX_GPIO_LEVELDETECT0) |
+ __raw_readl(bank->base + OMAP24XX_GPIO_LEVELDETECT1);
+ }
+}
+#endif
+
+#ifdef CONFIG_ARCH_OMAP1
+/*
+ * This only applies to chips that can't do both rising and falling edge
+ * detection at once. For all other chips, this function is a noop.
+ */
+static void _toggle_gpio_edge_triggering(struct gpio_bank *bank, int gpio)
+{
+ void __iomem *reg = bank->base;
+ u32 l = 0;
+
+ switch (bank->method) {
+ case METHOD_MPUIO:
+ reg += OMAP_MPUIO_GPIO_INT_EDGE;
+ break;
+#ifdef CONFIG_ARCH_OMAP15XX
+ case METHOD_GPIO_1510:
+ reg += OMAP1510_GPIO_INT_CONTROL;
+ break;
+#endif
+#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
+ case METHOD_GPIO_7XX:
+ reg += OMAP7XX_GPIO_INT_CONTROL;
+ break;
+#endif
+ default:
+ return;
+ }
+
+ l = __raw_readl(reg);
+ if ((l >> gpio) & 1)
+ l &= ~(1 << gpio);
+ else
+ l |= 1 << gpio;
+
+ __raw_writel(l, reg);
}
#endif
case METHOD_MPUIO:
reg += OMAP_MPUIO_GPIO_INT_EDGE;
l = __raw_readl(reg);
+ if ((trigger & IRQ_TYPE_SENSE_MASK) == IRQ_TYPE_EDGE_BOTH)
+ bank->toggle_mask |= 1 << gpio;
if (trigger & IRQ_TYPE_EDGE_RISING)
l |= 1 << gpio;
else if (trigger & IRQ_TYPE_EDGE_FALLING)
case METHOD_GPIO_1510:
reg += OMAP1510_GPIO_INT_CONTROL;
l = __raw_readl(reg);
+ if ((trigger & IRQ_TYPE_SENSE_MASK) == IRQ_TYPE_EDGE_BOTH)
+ bank->toggle_mask |= 1 << gpio;
if (trigger & IRQ_TYPE_EDGE_RISING)
l |= 1 << gpio;
else if (trigger & IRQ_TYPE_EDGE_FALLING)
__raw_writel(1 << gpio, bank->base + OMAP1610_GPIO_CLEAR_WAKEUPENA);
break;
#endif
-#ifdef CONFIG_ARCH_OMAP730
- case METHOD_GPIO_730:
- reg += OMAP730_GPIO_INT_CONTROL;
- l = __raw_readl(reg);
- if (trigger & IRQ_TYPE_EDGE_RISING)
- l |= 1 << gpio;
- else if (trigger & IRQ_TYPE_EDGE_FALLING)
- l &= ~(1 << gpio);
- else
- goto bad;
- break;
-#endif
-#ifdef CONFIG_ARCH_OMAP850
- case METHOD_GPIO_850:
- reg += OMAP850_GPIO_INT_CONTROL;
+#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
+ case METHOD_GPIO_7XX:
+ reg += OMAP7XX_GPIO_INT_CONTROL;
l = __raw_readl(reg);
+ if ((trigger & IRQ_TYPE_SENSE_MASK) == IRQ_TYPE_EDGE_BOTH)
+ bank->toggle_mask |= 1 << gpio;
if (trigger & IRQ_TYPE_EDGE_RISING)
l |= 1 << gpio;
else if (trigger & IRQ_TYPE_EDGE_FALLING)
goto bad;
break;
#endif
-#if defined(CONFIG_ARCH_OMAP24XX) || defined(CONFIG_ARCH_OMAP34XX) || \
- defined(CONFIG_ARCH_OMAP4)
+#ifdef CONFIG_ARCH_OMAP2PLUS
case METHOD_GPIO_24XX:
+ case METHOD_GPIO_44XX:
set_24xx_gpio_triggering(bank, gpio, trigger);
break;
#endif
reg += OMAP1610_GPIO_IRQSTATUS1;
break;
#endif
-#ifdef CONFIG_ARCH_OMAP730
- case METHOD_GPIO_730:
- reg += OMAP730_GPIO_INT_STATUS;
- break;
-#endif
-#ifdef CONFIG_ARCH_OMAP850
- case METHOD_GPIO_850:
- reg += OMAP850_GPIO_INT_STATUS;
+#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
+ case METHOD_GPIO_7XX:
+ reg += OMAP7XX_GPIO_INT_STATUS;
break;
#endif
-#if defined(CONFIG_ARCH_OMAP24XX) || defined(CONFIG_ARCH_OMAP34XX) || \
- defined(CONFIG_ARCH_OMAP4)
+#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3)
case METHOD_GPIO_24XX:
reg += OMAP24XX_GPIO_IRQSTATUS1;
break;
#endif
+#if defined(CONFIG_ARCH_OMAP4)
+ case METHOD_GPIO_44XX:
+ reg += OMAP4_GPIO_IRQSTATUS0;
+ break;
+#endif
default:
WARN_ON(1);
return;
__raw_writel(gpio_mask, reg);
/* Workaround for clearing DSP GPIO interrupts to allow retention */
-#if defined(CONFIG_ARCH_OMAP24XX) || defined(CONFIG_ARCH_OMAP34XX)
- reg = bank->base + OMAP24XX_GPIO_IRQSTATUS2;
if (cpu_is_omap24xx() || cpu_is_omap34xx())
+ reg = bank->base + OMAP24XX_GPIO_IRQSTATUS2;
+ else if (cpu_is_omap44xx())
+ reg = bank->base + OMAP4_GPIO_IRQSTATUS1;
+
+ if (cpu_is_omap24xx() || cpu_is_omap34xx() || cpu_is_omap44xx()) {
__raw_writel(gpio_mask, reg);
/* Flush posted write for the irq status to avoid spurious interrupts */
__raw_readl(reg);
-#endif
+ }
}
static inline void _clear_gpio_irqstatus(struct gpio_bank *bank, int gpio)
mask = 0xffff;
break;
#endif
-#ifdef CONFIG_ARCH_OMAP730
- case METHOD_GPIO_730:
- reg += OMAP730_GPIO_INT_MASK;
+#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
+ case METHOD_GPIO_7XX:
+ reg += OMAP7XX_GPIO_INT_MASK;
mask = 0xffffffff;
inv = 1;
break;
#endif
-#ifdef CONFIG_ARCH_OMAP850
- case METHOD_GPIO_850:
- reg += OMAP850_GPIO_INT_MASK;
+#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3)
+ case METHOD_GPIO_24XX:
+ reg += OMAP24XX_GPIO_IRQENABLE1;
mask = 0xffffffff;
- inv = 1;
break;
#endif
-#if defined(CONFIG_ARCH_OMAP24XX) || defined(CONFIG_ARCH_OMAP34XX) || \
- defined(CONFIG_ARCH_OMAP4)
- case METHOD_GPIO_24XX:
- reg += OMAP24XX_GPIO_IRQENABLE1;
+#if defined(CONFIG_ARCH_OMAP4)
+ case METHOD_GPIO_44XX:
+ reg += OMAP4_GPIO_IRQSTATUSSET0;
mask = 0xffffffff;
break;
#endif
l = gpio_mask;
break;
#endif
-#ifdef CONFIG_ARCH_OMAP730
- case METHOD_GPIO_730:
- reg += OMAP730_GPIO_INT_MASK;
+#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
+ case METHOD_GPIO_7XX:
+ reg += OMAP7XX_GPIO_INT_MASK;
l = __raw_readl(reg);
if (enable)
l &= ~(gpio_mask);
l |= gpio_mask;
break;
#endif
-#ifdef CONFIG_ARCH_OMAP850
- case METHOD_GPIO_850:
- reg += OMAP850_GPIO_INT_MASK;
- l = __raw_readl(reg);
+#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3)
+ case METHOD_GPIO_24XX:
if (enable)
- l &= ~(gpio_mask);
+ reg += OMAP24XX_GPIO_SETIRQENABLE1;
else
- l |= gpio_mask;
+ reg += OMAP24XX_GPIO_CLEARIRQENABLE1;
+ l = gpio_mask;
break;
#endif
-#if defined(CONFIG_ARCH_OMAP24XX) || defined(CONFIG_ARCH_OMAP34XX) || \
- defined(CONFIG_ARCH_OMAP4)
- case METHOD_GPIO_24XX:
+#ifdef CONFIG_ARCH_OMAP4
+ case METHOD_GPIO_44XX:
if (enable)
- reg += OMAP24XX_GPIO_SETIRQENABLE1;
+ reg += OMAP4_GPIO_IRQSTATUSSET0;
else
- reg += OMAP24XX_GPIO_CLEARIRQENABLE1;
+ reg += OMAP4_GPIO_IRQSTATUSCLR0;
l = gpio_mask;
break;
#endif
*/
static int _set_gpio_wakeup(struct gpio_bank *bank, int gpio, int enable)
{
- unsigned long flags;
+ unsigned long uninitialized_var(flags);
switch (bank->method) {
#ifdef CONFIG_ARCH_OMAP16XX
spin_unlock_irqrestore(&bank->lock, flags);
return 0;
#endif
-#if defined(CONFIG_ARCH_OMAP24XX) || defined(CONFIG_ARCH_OMAP34XX) || \
- defined(CONFIG_ARCH_OMAP4)
+#ifdef CONFIG_ARCH_OMAP2PLUS
case METHOD_GPIO_24XX:
+ case METHOD_GPIO_44XX:
if (bank->non_wakeup_gpios & (1 << gpio)) {
printk(KERN_ERR "Unable to modify wakeup on "
"non-wakeup GPIO%d\n",
__raw_writel(__raw_readl(reg) | (1 << offset), reg);
}
#endif
+ if (!cpu_class_is_omap1()) {
+ if (!bank->mod_usage) {
+ u32 ctrl;
+ ctrl = __raw_readl(bank->base + OMAP24XX_GPIO_CTRL);
+ ctrl &= 0xFFFFFFFE;
+ /* Module is enabled, clocks are not gated */
+ __raw_writel(ctrl, bank->base + OMAP24XX_GPIO_CTRL);
+ }
+ bank->mod_usage |= 1 << offset;
+ }
spin_unlock_irqrestore(&bank->lock, flags);
return 0;
__raw_writel(1 << offset, reg);
}
#endif
-#if defined(CONFIG_ARCH_OMAP24XX) || defined(CONFIG_ARCH_OMAP34XX) || \
- defined(CONFIG_ARCH_OMAP4)
- if (bank->method == METHOD_GPIO_24XX) {
+#ifdef CONFIG_ARCH_OMAP2PLUS
+ if ((bank->method == METHOD_GPIO_24XX) ||
+ (bank->method == METHOD_GPIO_44XX)) {
/* Disable wake-up during idle for dynamic tick */
void __iomem *reg = bank->base + OMAP24XX_GPIO_CLEARWKUENA;
__raw_writel(1 << offset, reg);
}
#endif
+ if (!cpu_class_is_omap1()) {
+ bank->mod_usage &= ~(1 << offset);
+ if (!bank->mod_usage) {
+ u32 ctrl;
+ ctrl = __raw_readl(bank->base + OMAP24XX_GPIO_CTRL);
+ /* Module is disabled, clocks are gated */
+ ctrl |= 1;
+ __raw_writel(ctrl, bank->base + OMAP24XX_GPIO_CTRL);
+ }
+ }
_reset_gpio(bank, bank->chip.base + offset);
spin_unlock_irqrestore(&bank->lock, flags);
}
{
void __iomem *isr_reg = NULL;
u32 isr;
- unsigned int gpio_irq;
+ unsigned int gpio_irq, gpio_index;
struct gpio_bank *bank;
u32 retrigger = 0;
int unmasked = 0;
if (bank->method == METHOD_GPIO_1610)
isr_reg = bank->base + OMAP1610_GPIO_IRQSTATUS1;
#endif
-#ifdef CONFIG_ARCH_OMAP730
- if (bank->method == METHOD_GPIO_730)
- isr_reg = bank->base + OMAP730_GPIO_INT_STATUS;
+#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
+ if (bank->method == METHOD_GPIO_7XX)
+ isr_reg = bank->base + OMAP7XX_GPIO_INT_STATUS;
#endif
-#ifdef CONFIG_ARCH_OMAP850
- if (bank->method == METHOD_GPIO_850)
- isr_reg = bank->base + OMAP850_GPIO_INT_STATUS;
-#endif
-#if defined(CONFIG_ARCH_OMAP24XX) || defined(CONFIG_ARCH_OMAP34XX) || \
- defined(CONFIG_ARCH_OMAP4)
+#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3)
if (bank->method == METHOD_GPIO_24XX)
isr_reg = bank->base + OMAP24XX_GPIO_IRQSTATUS1;
#endif
+#if defined(CONFIG_ARCH_OMAP4)
+ if (bank->method == METHOD_GPIO_44XX)
+ isr_reg = bank->base + OMAP4_GPIO_IRQSTATUS0;
+#endif
while(1) {
u32 isr_saved, level_mask = 0;
u32 enabled;
gpio_irq = bank->virtual_irq_start;
for (; isr != 0; isr >>= 1, gpio_irq++) {
+ gpio_index = get_gpio_index(irq_to_gpio(gpio_irq));
+
if (!(isr & 1))
continue;
+#ifdef CONFIG_ARCH_OMAP1
+ /*
+ * Some chips can't respond to both rising and falling
+ * at the same time. If this irq was requested with
+ * both flags, we need to flip the ICR data for the IRQ
+ * to respond to the IRQ for the opposite direction.
+ * This will be indicated in the bank toggle_mask.
+ */
+ if (bank->toggle_mask & (1 << gpio_index))
+ _toggle_gpio_edge_triggering(bank, gpio_index);
+#endif
+
generic_handle_irq(gpio_irq);
}
}
struct gpio_bank *bank = get_irq_chip_data(irq);
_set_gpio_irqenable(bank, gpio, 0);
+ _set_gpio_triggering(bank, get_gpio_index(gpio), IRQ_TYPE_NONE);
}
static void gpio_unmask_irq(unsigned int irq)
unsigned int gpio = irq - IH_GPIO_BASE;
struct gpio_bank *bank = get_irq_chip_data(irq);
unsigned int irq_mask = 1 << get_gpio_index(gpio);
+ struct irq_desc *desc = irq_to_desc(irq);
+ u32 trigger = desc->status & IRQ_TYPE_SENSE_MASK;
+
+ if (trigger)
+ _set_gpio_triggering(bank, get_gpio_index(gpio), trigger);
/* For level-triggered GPIOs, the clearing must be done after
* the HW source is cleared, thus after the handler has run */
return 0;
}
-static struct dev_pm_ops omap_mpuio_dev_pm_ops = {
+static const struct dev_pm_ops omap_mpuio_dev_pm_ops = {
.suspend_noirq = omap_mpuio_suspend_noirq,
.resume_noirq = omap_mpuio_resume_noirq,
};
return 0;
}
+static int gpio_is_input(struct gpio_bank *bank, int mask)
+{
+ void __iomem *reg = bank->base;
+
+ switch (bank->method) {
+ case METHOD_MPUIO:
+ reg += OMAP_MPUIO_IO_CNTL;
+ break;
+ case METHOD_GPIO_1510:
+ reg += OMAP1510_GPIO_DIR_CONTROL;
+ break;
+ case METHOD_GPIO_1610:
+ reg += OMAP1610_GPIO_DIRECTION;
+ break;
+ case METHOD_GPIO_7XX:
+ reg += OMAP7XX_GPIO_DIR_CONTROL;
+ break;
+ case METHOD_GPIO_24XX:
+ case METHOD_GPIO_44XX:
+ reg += OMAP24XX_GPIO_OE;
+ break;
+ }
+ return __raw_readl(reg) & mask;
+}
+
static int gpio_get(struct gpio_chip *chip, unsigned offset)
{
- return __omap_get_gpio_datain(chip->base + offset);
+ struct gpio_bank *bank;
+ void __iomem *reg;
+ int gpio;
+ u32 mask;
+
+ gpio = chip->base + offset;
+ bank = get_gpio_bank(gpio);
+ reg = bank->base;
+ mask = 1 << get_gpio_index(gpio);
+
+ if (gpio_is_input(bank, mask))
+ return _get_gpio_datain(bank, gpio);
+ else
+ return _get_gpio_dataout(bank, gpio);
}
static int gpio_output(struct gpio_chip *chip, unsigned offset, int value)
/*---------------------------------------------------------------------*/
static int initialized;
-#if !(defined(CONFIG_ARCH_OMAP3) || defined(CONFIG_ARCH_OMAP4))
+#if defined(CONFIG_ARCH_OMAP1) || defined(CONFIG_ARCH_OMAP2)
static struct clk * gpio_ick;
#endif
static struct clk *gpio_iclks[OMAP34XX_NR_GPIOS];
#endif
+static void __init omap_gpio_show_rev(void)
+{
+ u32 rev;
+
+ if (cpu_is_omap16xx())
+ rev = __raw_readw(gpio_bank[1].base + OMAP1610_GPIO_REVISION);
+ else if (cpu_is_omap24xx() || cpu_is_omap34xx())
+ rev = __raw_readl(gpio_bank[0].base + OMAP24XX_GPIO_REVISION);
+ else if (cpu_is_omap44xx())
+ rev = __raw_readl(gpio_bank[0].base + OMAP4_GPIO_REVISION);
+ else
+ return;
+
+ printk(KERN_INFO "OMAP GPIO hardware version %d.%d\n",
+ (rev >> 4) & 0x0f, rev & 0x0f);
+}
+
/* This lock class tells lockdep that GPIO irqs are in a different
* category than their parents, so it won't report false recursion.
*/
int i;
int gpio = 0;
struct gpio_bank *bank;
+ int bank_size = SZ_8K; /* Module 4KB + L4 4KB except on omap1 */
char clk_name[11];
initialized = 1;
#ifdef CONFIG_ARCH_OMAP15XX
if (cpu_is_omap15xx()) {
- printk(KERN_INFO "OMAP1510 GPIO hardware\n");
gpio_bank_count = 2;
gpio_bank = gpio_bank_1510;
+ bank_size = SZ_2K;
}
#endif
#if defined(CONFIG_ARCH_OMAP16XX)
if (cpu_is_omap16xx()) {
- u32 rev;
-
gpio_bank_count = 5;
gpio_bank = gpio_bank_1610;
- rev = __raw_readw(gpio_bank[1].base + OMAP1610_GPIO_REVISION);
- printk(KERN_INFO "OMAP GPIO hardware version %d.%d\n",
- (rev >> 4) & 0x0f, rev & 0x0f);
+ bank_size = SZ_2K;
}
#endif
-#ifdef CONFIG_ARCH_OMAP730
- if (cpu_is_omap730()) {
- printk(KERN_INFO "OMAP730 GPIO hardware\n");
- gpio_bank_count = 7;
- gpio_bank = gpio_bank_730;
- }
-#endif
-#ifdef CONFIG_ARCH_OMAP850
- if (cpu_is_omap850()) {
- printk(KERN_INFO "OMAP850 GPIO hardware\n");
+#if defined(CONFIG_ARCH_OMAP730) || defined(CONFIG_ARCH_OMAP850)
+ if (cpu_is_omap7xx()) {
gpio_bank_count = 7;
- gpio_bank = gpio_bank_850;
+ gpio_bank = gpio_bank_7xx;
+ bank_size = SZ_2K;
}
#endif
-
-#ifdef CONFIG_ARCH_OMAP24XX
+#ifdef CONFIG_ARCH_OMAP2
if (cpu_is_omap242x()) {
- int rev;
-
gpio_bank_count = 4;
gpio_bank = gpio_bank_242x;
- rev = __raw_readl(gpio_bank[0].base + OMAP24XX_GPIO_REVISION);
- printk(KERN_INFO "OMAP242x GPIO hardware version %d.%d\n",
- (rev >> 4) & 0x0f, rev & 0x0f);
}
if (cpu_is_omap243x()) {
- int rev;
-
gpio_bank_count = 5;
gpio_bank = gpio_bank_243x;
- rev = __raw_readl(gpio_bank[0].base + OMAP24XX_GPIO_REVISION);
- printk(KERN_INFO "OMAP243x GPIO hardware version %d.%d\n",
- (rev >> 4) & 0x0f, rev & 0x0f);
}
#endif
-#ifdef CONFIG_ARCH_OMAP34XX
+#ifdef CONFIG_ARCH_OMAP3
if (cpu_is_omap34xx()) {
- int rev;
-
gpio_bank_count = OMAP34XX_NR_GPIOS;
gpio_bank = gpio_bank_34xx;
- rev = __raw_readl(gpio_bank[0].base + OMAP24XX_GPIO_REVISION);
- printk(KERN_INFO "OMAP34xx GPIO hardware version %d.%d\n",
- (rev >> 4) & 0x0f, rev & 0x0f);
}
#endif
#ifdef CONFIG_ARCH_OMAP4
if (cpu_is_omap44xx()) {
- int rev;
-
gpio_bank_count = OMAP34XX_NR_GPIOS;
gpio_bank = gpio_bank_44xx;
- rev = __raw_readl(gpio_bank[0].base + OMAP24XX_GPIO_REVISION);
- printk(KERN_INFO "OMAP44xx GPIO hardware version %d.%d\n",
- (rev >> 4) & 0x0f, rev & 0x0f);
}
#endif
for (i = 0; i < gpio_bank_count; i++) {
bank = &gpio_bank[i];
spin_lock_init(&bank->lock);
+
+ /* Static mapping, never released */
+ bank->base = ioremap(bank->pbase, bank_size);
+ if (!bank->base) {
+ printk(KERN_ERR "Could not ioremap gpio bank%i\n", i);
+ continue;
+ }
+
if (bank_is_mpuio(bank))
__raw_writew(0xffff, bank->base + OMAP_MPUIO_GPIO_MASKIT);
if (cpu_is_omap15xx() && bank->method == METHOD_GPIO_1510) {
__raw_writew(0xffff, bank->base + OMAP1610_GPIO_IRQSTATUS1);
__raw_writew(0x0014, bank->base + OMAP1610_GPIO_SYSCONFIG);
}
- if (cpu_is_omap7xx() && bank->method == METHOD_GPIO_730) {
- __raw_writel(0xffffffff, bank->base + OMAP730_GPIO_INT_MASK);
- __raw_writel(0x00000000, bank->base + OMAP730_GPIO_INT_STATUS);
+ if (cpu_is_omap7xx() && bank->method == METHOD_GPIO_7XX) {
+ __raw_writel(0xffffffff, bank->base + OMAP7XX_GPIO_INT_MASK);
+ __raw_writel(0x00000000, bank->base + OMAP7XX_GPIO_INT_STATUS);
- gpio_count = 32; /* 730 has 32-bit GPIOs */
+ gpio_count = 32; /* 7xx has 32-bit GPIOs */
}
-#if defined(CONFIG_ARCH_OMAP24XX) || defined(CONFIG_ARCH_OMAP34XX) || \
- defined(CONFIG_ARCH_OMAP4)
- if (bank->method == METHOD_GPIO_24XX) {
+#ifdef CONFIG_ARCH_OMAP2PLUS
+ if ((bank->method == METHOD_GPIO_24XX) ||
+ (bank->method == METHOD_GPIO_44XX)) {
static const u32 non_wakeup_gpios[] = {
0xe203ffc0, 0x08700040
};
- __raw_writel(0x00000000, bank->base + OMAP24XX_GPIO_IRQENABLE1);
- __raw_writel(0xffffffff, bank->base + OMAP24XX_GPIO_IRQSTATUS1);
- __raw_writew(0x0015, bank->base + OMAP24XX_GPIO_SYSCONFIG);
- __raw_writel(0x00000000, bank->base + OMAP24XX_GPIO_DEBOUNCE_EN);
-
- /* Initialize interface clock ungated, module enabled */
- __raw_writel(0, bank->base + OMAP24XX_GPIO_CTRL);
+ if (cpu_is_omap44xx()) {
+ __raw_writel(0xffffffff, bank->base +
+ OMAP4_GPIO_IRQSTATUSCLR0);
+ __raw_writew(0x0015, bank->base +
+ OMAP4_GPIO_SYSCONFIG);
+ __raw_writel(0x00000000, bank->base +
+ OMAP4_GPIO_DEBOUNCENABLE);
+ /*
+ * Initialize interface clock ungated,
+ * module enabled
+ */
+ __raw_writel(0, bank->base + OMAP4_GPIO_CTRL);
+ } else {
+ __raw_writel(0x00000000, bank->base +
+ OMAP24XX_GPIO_IRQENABLE1);
+ __raw_writel(0xffffffff, bank->base +
+ OMAP24XX_GPIO_IRQSTATUS1);
+ __raw_writew(0x0015, bank->base +
+ OMAP24XX_GPIO_SYSCONFIG);
+ __raw_writel(0x00000000, bank->base +
+ OMAP24XX_GPIO_DEBOUNCE_EN);
+
+ /*
+ * Initialize interface clock ungated,
+ * module enabled
+ */
+ __raw_writel(0, bank->base +
+ OMAP24XX_GPIO_CTRL);
+ }
if (i < ARRAY_SIZE(non_wakeup_gpios))
bank->non_wakeup_gpios = non_wakeup_gpios[i];
gpio_count = 32;
}
#endif
+ bank->mod_usage = 0;
/* REVISIT eventually switch from OMAP-specific gpio structs
* over to the generic ones
*/
if (cpu_is_omap34xx())
omap_writel(1 << 0, 0x48306814);
+ omap_gpio_show_rev();
+
return 0;
}
-#if defined(CONFIG_ARCH_OMAP16XX) || defined(CONFIG_ARCH_OMAP24XX) || \
- defined(CONFIG_ARCH_OMAP34XX) || defined(CONFIG_ARCH_OMAP4)
+#if defined(CONFIG_ARCH_OMAP16XX) || defined(CONFIG_ARCH_OMAP2PLUS)
static int omap_gpio_suspend(struct sys_device *dev, pm_message_t mesg)
{
int i;
wake_set = bank->base + OMAP1610_GPIO_SET_WAKEUPENA;
break;
#endif
-#if defined(CONFIG_ARCH_OMAP24XX) || defined(CONFIG_ARCH_OMAP34XX) || \
- defined(CONFIG_ARCH_OMAP4)
+#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3)
case METHOD_GPIO_24XX:
wake_status = bank->base + OMAP24XX_GPIO_WAKE_EN;
wake_clear = bank->base + OMAP24XX_GPIO_CLEARWKUENA;
wake_set = bank->base + OMAP24XX_GPIO_SETWKUENA;
break;
#endif
+#ifdef CONFIG_ARCH_OMAP4
+ case METHOD_GPIO_44XX:
+ wake_status = bank->base + OMAP4_GPIO_IRQWAKEN0;
+ wake_clear = bank->base + OMAP4_GPIO_IRQWAKEN0;
+ wake_set = bank->base + OMAP4_GPIO_IRQWAKEN0;
+ break;
+#endif
default:
continue;
}
wake_set = bank->base + OMAP1610_GPIO_SET_WAKEUPENA;
break;
#endif
-#if defined(CONFIG_ARCH_OMAP24XX) || defined(CONFIG_ARCH_OMAP34XX) || \
- defined(CONFIG_ARCH_OMAP4)
+#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3)
case METHOD_GPIO_24XX:
wake_clear = bank->base + OMAP24XX_GPIO_CLEARWKUENA;
wake_set = bank->base + OMAP24XX_GPIO_SETWKUENA;
break;
#endif
+#ifdef CONFIG_ARCH_OMAP4
+ case METHOD_GPIO_44XX:
+ wake_clear = bank->base + OMAP4_GPIO_IRQWAKEN0;
+ wake_set = bank->base + OMAP4_GPIO_IRQWAKEN0;
+ break;
+#endif
default:
continue;
}
#endif
-#if defined(CONFIG_ARCH_OMAP24XX) || defined(CONFIG_ARCH_OMAP34XX) || \
- defined(CONFIG_ARCH_OMAP4)
+#ifdef CONFIG_ARCH_OMAP2PLUS
static int workaround_enabled;
if (!(bank->enabled_non_wakeup_gpios))
continue;
-#if defined(CONFIG_ARCH_OMAP24XX) || defined(CONFIG_ARCH_OMAP34XX) || \
- defined(CONFIG_ARCH_OMAP4)
- bank->saved_datain = __raw_readl(bank->base + OMAP24XX_GPIO_DATAIN);
- l1 = __raw_readl(bank->base + OMAP24XX_GPIO_FALLINGDETECT);
- l2 = __raw_readl(bank->base + OMAP24XX_GPIO_RISINGDETECT);
-#endif
+
+ if (cpu_is_omap24xx() || cpu_is_omap34xx()) {
+ bank->saved_datain = __raw_readl(bank->base +
+ OMAP24XX_GPIO_DATAIN);
+ l1 = __raw_readl(bank->base +
+ OMAP24XX_GPIO_FALLINGDETECT);
+ l2 = __raw_readl(bank->base +
+ OMAP24XX_GPIO_RISINGDETECT);
+ }
+
+ if (cpu_is_omap44xx()) {
+ bank->saved_datain = __raw_readl(bank->base +
+ OMAP4_GPIO_DATAIN);
+ l1 = __raw_readl(bank->base +
+ OMAP4_GPIO_FALLINGDETECT);
+ l2 = __raw_readl(bank->base +
+ OMAP4_GPIO_RISINGDETECT);
+ }
+
bank->saved_fallingdetect = l1;
bank->saved_risingdetect = l2;
l1 &= ~bank->enabled_non_wakeup_gpios;
l2 &= ~bank->enabled_non_wakeup_gpios;
-#if defined(CONFIG_ARCH_OMAP24XX) || defined(CONFIG_ARCH_OMAP34XX) || \
- defined(CONFIG_ARCH_OMAP4)
- __raw_writel(l1, bank->base + OMAP24XX_GPIO_FALLINGDETECT);
- __raw_writel(l2, bank->base + OMAP24XX_GPIO_RISINGDETECT);
-#endif
+
+ if (cpu_is_omap24xx() || cpu_is_omap34xx()) {
+ __raw_writel(l1, bank->base +
+ OMAP24XX_GPIO_FALLINGDETECT);
+ __raw_writel(l2, bank->base +
+ OMAP24XX_GPIO_RISINGDETECT);
+ }
+
+ if (cpu_is_omap44xx()) {
+ __raw_writel(l1, bank->base + OMAP4_GPIO_FALLINGDETECT);
+ __raw_writel(l2, bank->base + OMAP4_GPIO_RISINGDETECT);
+ }
+
c++;
}
if (!c) {
return;
for (i = 0; i < gpio_bank_count; i++) {
struct gpio_bank *bank = &gpio_bank[i];
- u32 l;
+ u32 l, gen, gen0, gen1;
if (!(bank->enabled_non_wakeup_gpios))
continue;
-#if defined(CONFIG_ARCH_OMAP24XX) || defined(CONFIG_ARCH_OMAP34XX) || \
- defined(CONFIG_ARCH_OMAP4)
- __raw_writel(bank->saved_fallingdetect,
+
+ if (cpu_is_omap24xx() || cpu_is_omap34xx()) {
+ __raw_writel(bank->saved_fallingdetect,
bank->base + OMAP24XX_GPIO_FALLINGDETECT);
- __raw_writel(bank->saved_risingdetect,
+ __raw_writel(bank->saved_risingdetect,
bank->base + OMAP24XX_GPIO_RISINGDETECT);
-#endif
+ l = __raw_readl(bank->base + OMAP24XX_GPIO_DATAIN);
+ }
+
+ if (cpu_is_omap44xx()) {
+ __raw_writel(bank->saved_fallingdetect,
+ bank->base + OMAP4_GPIO_FALLINGDETECT);
+ __raw_writel(bank->saved_risingdetect,
+ bank->base + OMAP4_GPIO_RISINGDETECT);
+ l = __raw_readl(bank->base + OMAP4_GPIO_DATAIN);
+ }
+
/* Check if any of the non-wakeup interrupt GPIOs have changed
* state. If so, generate an IRQ by software. This is
* horribly racy, but it's the best we can do to work around
* this silicon bug. */
-#if defined(CONFIG_ARCH_OMAP24XX) || defined(CONFIG_ARCH_OMAP34XX) || \
- defined(CONFIG_ARCH_OMAP4)
- l = __raw_readl(bank->base + OMAP24XX_GPIO_DATAIN);
-#endif
l ^= bank->saved_datain;
l &= bank->non_wakeup_gpios;
- if (l) {
+
+ /*
+ * No need to generate IRQs for the rising edge for gpio IRQs
+ * configured with falling edge only; and vice versa.
+ */
+ gen0 = l & bank->saved_fallingdetect;
+ gen0 &= bank->saved_datain;
+
+ gen1 = l & bank->saved_risingdetect;
+ gen1 &= ~(bank->saved_datain);
+
+ /* FIXME: Consider GPIO IRQs with level detections properly! */
+ gen = l & (~(bank->saved_fallingdetect) &
+ ~(bank->saved_risingdetect));
+ /* Consider all GPIO IRQs needed to be updated */
+ gen |= gen0 | gen1;
+
+ if (gen) {
u32 old0, old1;
-#if defined(CONFIG_ARCH_OMAP24XX) || defined(CONFIG_ARCH_OMAP34XX) || \
- defined(CONFIG_ARCH_OMAP4)
- old0 = __raw_readl(bank->base + OMAP24XX_GPIO_LEVELDETECT0);
- old1 = __raw_readl(bank->base + OMAP24XX_GPIO_LEVELDETECT1);
- __raw_writel(old0 | l, bank->base + OMAP24XX_GPIO_LEVELDETECT0);
- __raw_writel(old1 | l, bank->base + OMAP24XX_GPIO_LEVELDETECT1);
- __raw_writel(old0, bank->base + OMAP24XX_GPIO_LEVELDETECT0);
- __raw_writel(old1, bank->base + OMAP24XX_GPIO_LEVELDETECT1);
-#endif
+
+ if (cpu_is_omap24xx() || cpu_is_omap34xx()) {
+ old0 = __raw_readl(bank->base +
+ OMAP24XX_GPIO_LEVELDETECT0);
+ old1 = __raw_readl(bank->base +
+ OMAP24XX_GPIO_LEVELDETECT1);
+ __raw_writel(old0 | gen, bank->base +
+ OMAP24XX_GPIO_LEVELDETECT0);
+ __raw_writel(old1 | gen, bank->base +
+ OMAP24XX_GPIO_LEVELDETECT1);
+ __raw_writel(old0, bank->base +
+ OMAP24XX_GPIO_LEVELDETECT0);
+ __raw_writel(old1, bank->base +
+ OMAP24XX_GPIO_LEVELDETECT1);
+ }
+
+ if (cpu_is_omap44xx()) {
+ old0 = __raw_readl(bank->base +
+ OMAP4_GPIO_LEVELDETECT0);
+ old1 = __raw_readl(bank->base +
+ OMAP4_GPIO_LEVELDETECT1);
+ __raw_writel(old0 | l, bank->base +
+ OMAP4_GPIO_LEVELDETECT0);
+ __raw_writel(old1 | l, bank->base +
+ OMAP4_GPIO_LEVELDETECT1);
+ __raw_writel(old0, bank->base +
+ OMAP4_GPIO_LEVELDETECT0);
+ __raw_writel(old1, bank->base +
+ OMAP4_GPIO_LEVELDETECT1);
+ }
}
}
#endif
+#ifdef CONFIG_ARCH_OMAP3
+/* save the registers of bank 2-6 */
+void omap_gpio_save_context(void)
+{
+ int i;
+
+ /* saving banks from 2-6 only since GPIO1 is in WKUP */
+ for (i = 1; i < gpio_bank_count; i++) {
+ struct gpio_bank *bank = &gpio_bank[i];
+ gpio_context[i].sysconfig =
+ __raw_readl(bank->base + OMAP24XX_GPIO_SYSCONFIG);
+ gpio_context[i].irqenable1 =
+ __raw_readl(bank->base + OMAP24XX_GPIO_IRQENABLE1);
+ gpio_context[i].irqenable2 =
+ __raw_readl(bank->base + OMAP24XX_GPIO_IRQENABLE2);
+ gpio_context[i].wake_en =
+ __raw_readl(bank->base + OMAP24XX_GPIO_WAKE_EN);
+ gpio_context[i].ctrl =
+ __raw_readl(bank->base + OMAP24XX_GPIO_CTRL);
+ gpio_context[i].oe =
+ __raw_readl(bank->base + OMAP24XX_GPIO_OE);
+ gpio_context[i].leveldetect0 =
+ __raw_readl(bank->base + OMAP24XX_GPIO_LEVELDETECT0);
+ gpio_context[i].leveldetect1 =
+ __raw_readl(bank->base + OMAP24XX_GPIO_LEVELDETECT1);
+ gpio_context[i].risingdetect =
+ __raw_readl(bank->base + OMAP24XX_GPIO_RISINGDETECT);
+ gpio_context[i].fallingdetect =
+ __raw_readl(bank->base + OMAP24XX_GPIO_FALLINGDETECT);
+ gpio_context[i].dataout =
+ __raw_readl(bank->base + OMAP24XX_GPIO_DATAOUT);
+ gpio_context[i].setwkuena =
+ __raw_readl(bank->base + OMAP24XX_GPIO_SETWKUENA);
+ gpio_context[i].setdataout =
+ __raw_readl(bank->base + OMAP24XX_GPIO_SETDATAOUT);
+ }
+}
+
+/* restore the required registers of bank 2-6 */
+void omap_gpio_restore_context(void)
+{
+ int i;
+
+ for (i = 1; i < gpio_bank_count; i++) {
+ struct gpio_bank *bank = &gpio_bank[i];
+ __raw_writel(gpio_context[i].sysconfig,
+ bank->base + OMAP24XX_GPIO_SYSCONFIG);
+ __raw_writel(gpio_context[i].irqenable1,
+ bank->base + OMAP24XX_GPIO_IRQENABLE1);
+ __raw_writel(gpio_context[i].irqenable2,
+ bank->base + OMAP24XX_GPIO_IRQENABLE2);
+ __raw_writel(gpio_context[i].wake_en,
+ bank->base + OMAP24XX_GPIO_WAKE_EN);
+ __raw_writel(gpio_context[i].ctrl,
+ bank->base + OMAP24XX_GPIO_CTRL);
+ __raw_writel(gpio_context[i].oe,
+ bank->base + OMAP24XX_GPIO_OE);
+ __raw_writel(gpio_context[i].leveldetect0,
+ bank->base + OMAP24XX_GPIO_LEVELDETECT0);
+ __raw_writel(gpio_context[i].leveldetect1,
+ bank->base + OMAP24XX_GPIO_LEVELDETECT1);
+ __raw_writel(gpio_context[i].risingdetect,
+ bank->base + OMAP24XX_GPIO_RISINGDETECT);
+ __raw_writel(gpio_context[i].fallingdetect,
+ bank->base + OMAP24XX_GPIO_FALLINGDETECT);
+ __raw_writel(gpio_context[i].dataout,
+ bank->base + OMAP24XX_GPIO_DATAOUT);
+ __raw_writel(gpio_context[i].setwkuena,
+ bank->base + OMAP24XX_GPIO_SETWKUENA);
+ __raw_writel(gpio_context[i].setdataout,
+ bank->base + OMAP24XX_GPIO_SETDATAOUT);
+ }
+}
+#endif
+
/*
* This may get called early from board specific init
* for boards that have interrupts routed via FPGA.
mpuio_init();
-#if defined(CONFIG_ARCH_OMAP16XX) || defined(CONFIG_ARCH_OMAP24XX) || \
- defined(CONFIG_ARCH_OMAP34XX) || defined(CONFIG_ARCH_OMAP4)
+#if defined(CONFIG_ARCH_OMAP16XX) || defined(CONFIG_ARCH_OMAP2PLUS)
if (cpu_is_omap16xx() || cpu_class_is_omap2()) {
if (ret == 0) {
ret = sysdev_class_register(&omap_gpio_sysclass);
#include <linux/debugfs.h>
#include <linux/seq_file.h>
-static int gpio_is_input(struct gpio_bank *bank, int mask)
-{
- void __iomem *reg = bank->base;
-
- switch (bank->method) {
- case METHOD_MPUIO:
- reg += OMAP_MPUIO_IO_CNTL;
- break;
- case METHOD_GPIO_1510:
- reg += OMAP1510_GPIO_DIR_CONTROL;
- break;
- case METHOD_GPIO_1610:
- reg += OMAP1610_GPIO_DIRECTION;
- break;
- case METHOD_GPIO_730:
- reg += OMAP730_GPIO_DIR_CONTROL;
- break;
- case METHOD_GPIO_850:
- reg += OMAP850_GPIO_DIR_CONTROL;
- break;
- case METHOD_GPIO_24XX:
- reg += OMAP24XX_GPIO_OE;
- break;
- }
- return __raw_readl(reg) & mask;
-}
-
-
static int dbg_gpio_show(struct seq_file *s, void *unused)
{
unsigned i, j, gpio;
if (bank_is_mpuio(bank))
gpio = OMAP_MPUIO(0);
- else if (cpu_class_is_omap2() || cpu_is_omap730() ||
- cpu_is_omap850())
+ else if (cpu_class_is_omap2() || cpu_is_omap7xx())
bankwidth = 32;
for (j = 0; j < bankwidth; j++, gpio++, mask <<= 1) {
/* FIXME for at least omap2, show pullup/pulldown state */
irqstat = irq_desc[irq].status;
-#if defined(CONFIG_ARCH_OMAP16XX) || defined(CONFIG_ARCH_OMAP24XX) || \
- defined(CONFIG_ARCH_OMAP34XX) || defined(CONFIG_ARCH_OMAP4)
+#if defined(CONFIG_ARCH_OMAP16XX) || defined(CONFIG_ARCH_OMAP2PLUS)
if (is_in && ((bank->suspend_wakeup & mask)
|| irqstat & IRQ_TYPE_SENSE_MASK)) {
char *trigger = NULL;
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff