#include <linux/serial_core.h>
#include <linux/platform_device.h>
#include <linux/io.h>
+#include <linux/i2c.h>
+#include <linux/fb.h>
+#include <linux/gpio.h>
+#include <linux/delay.h>
+#include <linux/smsc911x.h>
+
+#ifdef CONFIG_SMDK6410_WM1190_EV1
+#include <linux/mfd/wm8350/core.h>
+#include <linux/mfd/wm8350/pmic.h>
+#endif
+
+#include <video/platform_lcd.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
#include <mach/hardware.h>
+#include <mach/regs-fb.h>
#include <mach/map.h>
#include <asm/irq.h>
#include <asm/mach-types.h>
#include <plat/regs-serial.h>
+#include <plat/regs-modem.h>
+#include <plat/regs-gpio.h>
+#include <plat/regs-sys.h>
#include <plat/iic.h>
+#include <plat/fb.h>
+#include <plat/gpio-cfg.h>
#include <plat/s3c6410.h>
#include <plat/clock.h>
[0] = {
.hwport = 0,
.flags = 0,
- .ucon = 0x3c5,
- .ulcon = 0x03,
- .ufcon = 0x51,
+ .ucon = UCON,
+ .ulcon = ULCON,
+ .ufcon = UFCON,
},
[1] = {
.hwport = 1,
.flags = 0,
- .ucon = 0x3c5,
- .ulcon = 0x03,
- .ufcon = 0x51,
+ .ucon = UCON,
+ .ulcon = ULCON,
+ .ufcon = UFCON,
+ },
+ [2] = {
+ .hwport = 2,
+ .flags = 0,
+ .ucon = UCON,
+ .ulcon = ULCON,
+ .ufcon = UFCON,
+ },
+ [3] = {
+ .hwport = 3,
+ .flags = 0,
+ .ucon = UCON,
+ .ulcon = ULCON,
+ .ufcon = UFCON,
},
};
-struct map_desc smdk6410_iodesc[] = {};
+/* framebuffer and LCD setup. */
+
+/* GPF15 = LCD backlight control
+ * GPF13 => Panel power
+ * GPN5 = LCD nRESET signal
+ * PWM_TOUT1 => backlight brightness
+ */
+
+static void smdk6410_lcd_power_set(struct plat_lcd_data *pd,
+ unsigned int power)
+{
+ if (power) {
+ gpio_direction_output(S3C64XX_GPF(13), 1);
+ gpio_direction_output(S3C64XX_GPF(15), 1);
+
+ /* fire nRESET on power up */
+ gpio_direction_output(S3C64XX_GPN(5), 0);
+ msleep(10);
+ gpio_direction_output(S3C64XX_GPN(5), 1);
+ msleep(1);
+ } else {
+ gpio_direction_output(S3C64XX_GPF(15), 0);
+ gpio_direction_output(S3C64XX_GPF(13), 0);
+ }
+}
+
+static struct plat_lcd_data smdk6410_lcd_power_data = {
+ .set_power = smdk6410_lcd_power_set,
+};
+
+static struct platform_device smdk6410_lcd_powerdev = {
+ .name = "platform-lcd",
+ .dev.parent = &s3c_device_fb.dev,
+ .dev.platform_data = &smdk6410_lcd_power_data,
+};
+
+static struct s3c_fb_pd_win smdk6410_fb_win0 = {
+ /* this is to ensure we use win0 */
+ .win_mode = {
+ .pixclock = 41094,
+ .left_margin = 8,
+ .right_margin = 13,
+ .upper_margin = 7,
+ .lower_margin = 5,
+ .hsync_len = 3,
+ .vsync_len = 1,
+ .xres = 800,
+ .yres = 480,
+ },
+ .max_bpp = 32,
+ .default_bpp = 16,
+};
+
+/* 405566 clocks per frame => 60Hz refresh requires 24333960Hz clock */
+static struct s3c_fb_platdata smdk6410_lcd_pdata __initdata = {
+ .setup_gpio = s3c64xx_fb_gpio_setup_24bpp,
+ .win[0] = &smdk6410_fb_win0,
+ .vidcon0 = VIDCON0_VIDOUT_RGB | VIDCON0_PNRMODE_RGB,
+ .vidcon1 = VIDCON1_INV_HSYNC | VIDCON1_INV_VSYNC,
+};
+
+static struct resource smdk6410_smsc911x_resources[] = {
+ [0] = {
+ .start = 0x18000000,
+ .end = 0x18000000 + SZ_64K - 1,
+ .flags = IORESOURCE_MEM,
+ },
+ [1] = {
+ .start = S3C_EINT(10),
+ .end = S3C_EINT(10),
+ .flags = IORESOURCE_IRQ | IRQ_TYPE_LEVEL_LOW,
+ },
+};
+
+static struct smsc911x_platform_config smdk6410_smsc911x_pdata = {
+ .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
+ .irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN,
+ .flags = SMSC911X_USE_32BIT | SMSC911X_FORCE_INTERNAL_PHY,
+ .phy_interface = PHY_INTERFACE_MODE_MII,
+};
+
+
+static struct platform_device smdk6410_smsc911x = {
+ .name = "smsc911x",
+ .id = -1,
+ .num_resources = ARRAY_SIZE(smdk6410_smsc911x_resources),
+ .resource = &smdk6410_smsc911x_resources[0],
+ .dev = {
+ .platform_data = &smdk6410_smsc911x_pdata,
+ },
+};
+
+static struct map_desc smdk6410_iodesc[] = {};
static struct platform_device *smdk6410_devices[] __initdata = {
+#ifdef CONFIG_SMDK6410_SD_CH0
&s3c_device_hsmmc0,
+#endif
+#ifdef CONFIG_SMDK6410_SD_CH1
+ &s3c_device_hsmmc1,
+#endif
&s3c_device_i2c0,
+ &s3c_device_i2c1,
+ &s3c_device_fb,
+ &s3c_device_usb,
+ &s3c_device_usb_hsotg,
+ &smdk6410_lcd_powerdev,
+
+ &smdk6410_smsc911x,
+};
+
+#ifdef CONFIG_SMDK6410_WM1190_EV1
+/* S3C64xx internal logic & PLL */
+static struct regulator_init_data wm8350_dcdc1_data = {
+ .constraints = {
+ .name = "PVDD_INT/PVDD_PLL",
+ .min_uV = 1200000,
+ .max_uV = 1200000,
+ .always_on = 1,
+ .apply_uV = 1,
+ },
+};
+
+/* Memory */
+static struct regulator_init_data wm8350_dcdc3_data = {
+ .constraints = {
+ .name = "PVDD_MEM",
+ .min_uV = 1800000,
+ .max_uV = 1800000,
+ .always_on = 1,
+ .state_mem = {
+ .uV = 1800000,
+ .mode = REGULATOR_MODE_NORMAL,
+ .enabled = 1,
+ },
+ .initial_state = PM_SUSPEND_MEM,
+ },
+};
+
+/* USB, EXT, PCM, ADC/DAC, USB, MMC */
+static struct regulator_init_data wm8350_dcdc4_data = {
+ .constraints = {
+ .name = "PVDD_HI/PVDD_EXT/PVDD_SYS/PVCCM2MTV",
+ .min_uV = 3000000,
+ .max_uV = 3000000,
+ .always_on = 1,
+ },
+};
+
+/* ARM core */
+static struct regulator_consumer_supply dcdc6_consumers[] = {
+ {
+ .supply = "vddarm",
+ }
};
-extern void s3c64xx_init_io(struct map_desc *, int);
+static struct regulator_init_data wm8350_dcdc6_data = {
+ .constraints = {
+ .name = "PVDD_ARM",
+ .min_uV = 1000000,
+ .max_uV = 1300000,
+ .always_on = 1,
+ .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE,
+ },
+ .num_consumer_supplies = ARRAY_SIZE(dcdc6_consumers),
+ .consumer_supplies = dcdc6_consumers,
+};
+
+/* Alive */
+static struct regulator_init_data wm8350_ldo1_data = {
+ .constraints = {
+ .name = "PVDD_ALIVE",
+ .min_uV = 1200000,
+ .max_uV = 1200000,
+ .always_on = 1,
+ .apply_uV = 1,
+ },
+};
+
+/* OTG */
+static struct regulator_init_data wm8350_ldo2_data = {
+ .constraints = {
+ .name = "PVDD_OTG",
+ .min_uV = 3300000,
+ .max_uV = 3300000,
+ .always_on = 1,
+ },
+};
+
+/* LCD */
+static struct regulator_init_data wm8350_ldo3_data = {
+ .constraints = {
+ .name = "PVDD_LCD",
+ .min_uV = 3000000,
+ .max_uV = 3000000,
+ .always_on = 1,
+ },
+};
+
+/* OTGi/1190-EV1 HPVDD & AVDD */
+static struct regulator_init_data wm8350_ldo4_data = {
+ .constraints = {
+ .name = "PVDD_OTGI/HPVDD/AVDD",
+ .min_uV = 1200000,
+ .max_uV = 1200000,
+ .apply_uV = 1,
+ .always_on = 1,
+ },
+};
+
+static struct {
+ int regulator;
+ struct regulator_init_data *initdata;
+} wm1190_regulators[] = {
+ { WM8350_DCDC_1, &wm8350_dcdc1_data },
+ { WM8350_DCDC_3, &wm8350_dcdc3_data },
+ { WM8350_DCDC_4, &wm8350_dcdc4_data },
+ { WM8350_DCDC_6, &wm8350_dcdc6_data },
+ { WM8350_LDO_1, &wm8350_ldo1_data },
+ { WM8350_LDO_2, &wm8350_ldo2_data },
+ { WM8350_LDO_3, &wm8350_ldo3_data },
+ { WM8350_LDO_4, &wm8350_ldo4_data },
+};
+
+static int __init smdk6410_wm8350_init(struct wm8350 *wm8350)
+{
+ int i;
+
+ /* Configure the IRQ line */
+ s3c_gpio_setpull(S3C64XX_GPN(12), S3C_GPIO_PULL_UP);
+
+ /* Instantiate the regulators */
+ for (i = 0; i < ARRAY_SIZE(wm1190_regulators); i++)
+ wm8350_register_regulator(wm8350,
+ wm1190_regulators[i].regulator,
+ wm1190_regulators[i].initdata);
+
+ return 0;
+}
+
+static struct wm8350_platform_data __initdata smdk6410_wm8350_pdata = {
+ .init = smdk6410_wm8350_init,
+ .irq_high = 1,
+};
+#endif
+
+static struct i2c_board_info i2c_devs0[] __initdata = {
+ { I2C_BOARD_INFO("24c08", 0x50), },
+ { I2C_BOARD_INFO("wm8580", 0x1b), },
+
+#ifdef CONFIG_SMDK6410_WM1190_EV1
+ { I2C_BOARD_INFO("wm8350", 0x1a),
+ .platform_data = &smdk6410_wm8350_pdata,
+ .irq = S3C_EINT(12),
+ },
+#endif
+};
+
+static struct i2c_board_info i2c_devs1[] __initdata = {
+ { I2C_BOARD_INFO("24c128", 0x57), }, /* Samsung S524AD0XD1 */
+};
static void __init smdk6410_map_io(void)
{
+ u32 tmp;
+
s3c64xx_init_io(smdk6410_iodesc, ARRAY_SIZE(smdk6410_iodesc));
s3c24xx_init_clocks(12000000);
s3c24xx_init_uarts(smdk6410_uartcfgs, ARRAY_SIZE(smdk6410_uartcfgs));
+
+ /* set the LCD type */
+
+ tmp = __raw_readl(S3C64XX_SPCON);
+ tmp &= ~S3C64XX_SPCON_LCD_SEL_MASK;
+ tmp |= S3C64XX_SPCON_LCD_SEL_RGB;
+ __raw_writel(tmp, S3C64XX_SPCON);
+
+ /* remove the lcd bypass */
+ tmp = __raw_readl(S3C64XX_MODEM_MIFPCON);
+ tmp &= ~MIFPCON_LCD_BYPASS;
+ __raw_writel(tmp, S3C64XX_MODEM_MIFPCON);
}
static void __init smdk6410_machine_init(void)
{
s3c_i2c0_set_platdata(NULL);
+ s3c_i2c1_set_platdata(NULL);
+ s3c_fb_set_platdata(&smdk6410_lcd_pdata);
+
+ gpio_request(S3C64XX_GPN(5), "LCD power");
+ gpio_request(S3C64XX_GPF(13), "LCD power");
+ gpio_request(S3C64XX_GPF(15), "LCD power");
+
+ i2c_register_board_info(0, i2c_devs0, ARRAY_SIZE(i2c_devs0));
+ i2c_register_board_info(1, i2c_devs1, ARRAY_SIZE(i2c_devs1));
+
platform_add_devices(smdk6410_devices, ARRAY_SIZE(smdk6410_devices));
}
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff