slots - Reserve the slot index for the given driver.
This option takes multiple strings.
See "Module Autoloading Support" section for details.
+ debug - Specifies the debug message level
+ (0 = disable debug prints, 1 = normal debug messages,
+ 2 = verbose debug messages)
+ This option appears only when CONFIG_SND_DEBUG=y.
+ This option can be dynamically changed via sysfs
+ /sys/modules/snd/parameters/debug file.
Module snd-pcm-oss
------------------
sbirq - IRQ # for CMI8330 chip (SB16)
sbdma8 - 8bit DMA # for CMI8330 chip (SB16)
sbdma16 - 16bit DMA # for CMI8330 chip (SB16)
+ fmport - (optional) OPL3 I/O port
+ mpuport - (optional) MPU401 I/O port
+ mpuirq - (optional) MPU401 irq #
This module supports multiple cards and autoprobe.
The power-management is supported.
- Module snd-cs4232
- -----------------
-
- Module for sound cards based on CS4232/CS4232A ISA chips.
-
- isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
-
- with isapnp=0, the following options are available:
-
- port - port # for CS4232 chip (PnP setup - 0x534)
- cport - control port # for CS4232 chip (PnP setup - 0x120,0x210,0xf00)
- mpu_port - port # for MPU-401 UART (PnP setup - 0x300), -1 = disable
- fm_port - FM port # for CS4232 chip (PnP setup - 0x388), -1 = disable
- irq - IRQ # for CS4232 chip (5,7,9,11,12,15)
- mpu_irq - IRQ # for MPU-401 UART (9,11,12,15)
- dma1 - first DMA # for CS4232 chip (0,1,3)
- dma2 - second DMA # for Yamaha CS4232 chip (0,1,3), -1 = disable
-
- This module supports multiple cards. This module does not support autoprobe
- (if ISA PnP is not used) thus main port must be specified!!! Other ports are
- optional.
-
- The power-management is supported.
-
Module snd-cs4236
-----------------
- Module for sound cards based on CS4235/CS4236/CS4236B/CS4237B/
+ Module for sound cards based on CS4232/CS4232A,
+ CS4235/CS4236/CS4236B/CS4237B/
CS4238B/CS4239 ISA chips.
isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
The power-management is supported.
+ This module is aliased as snd-cs4232 since it provides the old
+ snd-cs4232 functionality, too.
+
Module snd-cs4281
-----------------
The power-management is supported.
+ Module snd-ctxfi
+ ----------------
+
+ Module for Creative Sound Blaster X-Fi boards (20k1 / 20k2 chips)
+ * Creative Sound Blaster X-Fi Titanium Fatal1ty Champion Series
+ * Creative Sound Blaster X-Fi Titanium Fatal1ty Professional Series
+ * Creative Sound Blaster X-Fi Titanium Professional Audio
+ * Creative Sound Blaster X-Fi Titanium
+ * Creative Sound Blaster X-Fi Elite Pro
+ * Creative Sound Blaster X-Fi Platinum
+ * Creative Sound Blaster X-Fi Fatal1ty
+ * Creative Sound Blaster X-Fi XtremeGamer
+ * Creative Sound Blaster X-Fi XtremeMusic
+
+ reference_rate - reference sample rate, 44100 or 48000 (default)
+ multiple - multiple to ref. sample rate, 1 or 2 (default)
+
+ This module supports multiple cards.
+
Module snd-darla20
------------------
or input, but you may use this module for any application which
requires a sound card (like RealPlayer).
+ pcm_devs - Number of PCM devices assigned to each card
+ (default = 1, up to 4)
+ pcm_substreams - Number of PCM substreams assigned to each PCM
+ (default = 8, up to 128)
+ hrtimer - Use hrtimer (=1, default) or system timer (=0)
+ fake_buffer - Fake buffer allocations (default = 1)
+
+ When multiple PCM devices are created, snd-dummy gives different
+ behavior to each PCM device:
+ 0 = interleaved with mmap support
+ 1 = non-interleaved with mmap support
+ 2 = interleaved without mmap
+ 3 = non-interleaved without mmap
+
+ As default, snd-dummy drivers doesn't allocate the real buffers
+ but either ignores read/write or mmap a single dummy page to all
+ buffer pages, in order to save the resouces. If your apps need
+ the read/ written buffer data to be consistent, pass fake_buffer=0
+ option.
+
The power-management is supported.
Module snd-echo3g
Module for ESS AudioDrive ES-1688 and ES-688 sound cards.
port - port # for ES-1688 chip (0x220,0x240,0x260)
+ fm_port - port # for OPL3 (option; share the same port as default)
mpu_port - port # for MPU-401 port (0x300,0x310,0x320,0x330), -1 = disable (default)
irq - IRQ # for ES-1688 chip (5,7,9,10)
mpu_irq - IRQ # for MPU-401 port (5,7,9,10)
model - force the model name
position_fix - Fix DMA pointer (0 = auto, 1 = use LPIB, 2 = POSBUF)
probe_mask - Bitmask to probe codecs (default = -1, meaning all slots)
+ When the bit 8 (0x100) is set, the lower 8 bits are used
+ as the "fixed" codec slots; i.e. the driver probes the
+ slots regardless what hardware reports back
probe_only - Only probing and no codec initialization (default=off);
Useful to check the initial codec status for debugging
bdl_pos_adj - Specifies the DMA IRQ timing delay in samples.
Passing -1 will make the driver to choose the appropriate
value based on the controller chip.
+ patch - Specifies the early "patch" files to modify the HD-audio
+ setup before initializing the codecs. This option is
+ available only when CONFIG_SND_HDA_PATCH_LOADER=y is set.
+ See HD-Audio.txt for details.
[Single (global) options]
single_cmd - Use single immediate commands to communicate with
codecs (for debugging only)
enable_msi - Enable Message Signaled Interrupt (MSI) (default = off)
- power_save - Automatic power-saving timtout (in second, 0 =
+ power_save - Automatic power-saving timeout (in second, 0 =
disable)
power_save_controller - Reset HD-audio controller in power-saving mode
(default = on)
* Onkyo SE-90PCI
* Onkyo SE-200PCI
* ESI Juli@
+ * ESI Maya44
* Hercules Fortissimo IV
* EGO-SYS WaveTerminal 192M
prodigy71xt, prodigy71hifi, prodigyhd2, prodigy192,
juli, aureon51, aureon71, universe, ap192, k8x800,
phase22, phase28, ms300, av710, se200pci, se90pci,
- fortissimo4, sn25p, WT192M
+ fortissimo4, sn25p, WT192M, maya44
This module supports multiple cards and autoprobe.
This module supports multiple cards.
The driver requires the firmware loader support on kernel.
+ Module snd-lx6464es
+ -------------------
+
+ Module for Digigram LX6464ES boards
+
+ This module supports multiple cards.
+
Module snd-maestro3
-------------------
This module supports multiple devices and PnP.
+ Module snd-msnd-classic
+ -----------------------
+
+ Module for Turtle Beach MultiSound Classic, Tahiti or Monterey
+ soundcards.
+
+ io - Port # for msnd-classic card
+ irq - IRQ # for msnd-classic card
+ mem - Memory address (0xb0000, 0xc8000, 0xd0000, 0xd8000,
+ 0xe0000 or 0xe8000)
+ write_ndelay - enable write ndelay (default = 1)
+ calibrate_signal - calibrate signal (default = 0)
+ isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
+ digital - Digital daughterboard present (default = 0)
+ cfg - Config port (0x250, 0x260 or 0x270) default = PnP
+ reset - Reset all devices
+ mpu_io - MPU401 I/O port
+ mpu_irq - MPU401 irq#
+ ide_io0 - IDE port #0
+ ide_io1 - IDE port #1
+ ide_irq - IDE irq#
+ joystick_io - Joystick I/O port
+
+ The driver requires firmware files "turtlebeach/msndinit.bin" and
+ "turtlebeach/msndperm.bin" in the proper firmware directory.
+
+ See Documentation/sound/oss/MultiSound for important information
+ about this driver. Note that it has been discontinued, but the
+ Voyetra Turtle Beach knowledge base entry for it is still available
+ at
+ http://www.turtlebeach.com/site/kb_ftp/790.asp
+
+ Module snd-msnd-pinnacle
+ ------------------------
+
+ Module for Turtle Beach MultiSound Pinnacle/Fiji soundcards.
+
+ io - Port # for pinnacle/fiji card
+ irq - IRQ # for pinnalce/fiji card
+ mem - Memory address (0xb0000, 0xc8000, 0xd0000, 0xd8000,
+ 0xe0000 or 0xe8000)
+ write_ndelay - enable write ndelay (default = 1)
+ calibrate_signal - calibrate signal (default = 0)
+ isapnp - ISA PnP detection - 0 = disable, 1 = enable (default)
+
+ The driver requires firmware files "turtlebeach/pndspini.bin" and
+ "turtlebeach/pndsperm.bin" in the proper firmware directory.
+
Module snd-mtpav
----------------
Module snd-sc6000
-----------------
- Module for Gallant SC-6000 soundcard.
+ Module for Gallant SC-6000 soundcard and later models: SC-6600
+ and SC-7000.
port - Port # (0x220 or 0x240)
mss_port - MSS Port # (0x530 or 0xe80)
irq - IRQ # (5,7,9,10,11)
mpu_irq - MPU-401 IRQ # (5,7,9,10) ,0 - no MPU-401 irq
dma - DMA # (1,3,0)
+ joystick - Enable gameport - 0 = disable (default), 1 = enable
This module supports multiple cards.
-------------------
Module for sound cards based on the Asus AV100/AV200 chips,
- i.e., Xonar D1, DX, D2, D2X, HDAV1.3 (Deluxe), and Essence STX.
+ i.e., Xonar D1, DX, D2, D2X, HDAV1.3 (Deluxe), Essence ST
+ (Deluxe) and Essence STX.
This module supports autoprobe and multiple cards.
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff