nfsd: nfsd should drop CAP_MKNOD for non-root

[safe/jmp/linux-2.6] / Documentation / networking / dccp.txt

diff --git a/Documentation/networking/dccp.txt b/Documentation/networking/dccp.txt
index d76905a..7a3bb1a 100644 (file)
--- a/Documentation/networking/dccp.txt
+++ b/Documentation/networking/dccp.txt
@@ -57,6 +57,30 @@ can be set before calling bind().
 DCCP_SOCKOPT_GET_CUR_MPS is read-only and retrieves the current maximum packet
 size (application payload size) in bytes, see RFC 4340, section 14.
 
+DCCP_SOCKOPT_AVAILABLE_CCIDS is also read-only and returns the list of CCIDs
+supported by the endpoint (see include/linux/dccp.h for symbolic constants).
+The caller needs to provide a sufficiently large (> 2) array of type uint8_t.
+
+DCCP_SOCKOPT_CCID is write-only and sets both the TX and RX CCIDs at the same
+time, combining the operation of the next two socket options. This option is
+preferrable over the latter two, since often applications will use the same
+type of CCID for both directions; and mixed use of CCIDs is not currently well
+understood. This socket option takes as argument at least one uint8_t value, or
+an array of uint8_t values, which must match available CCIDS (see above). CCIDs
+must be registered on the socket before calling connect() or listen().
+
+DCCP_SOCKOPT_TX_CCID is read/write. It returns the current CCID (if set) or sets
+the preference list for the TX CCID, using the same format as DCCP_SOCKOPT_CCID.
+Please note that the getsockopt argument type here is `int', not uint8_t.
+
+DCCP_SOCKOPT_RX_CCID is analogous to DCCP_SOCKOPT_TX_CCID, but for the RX CCID.
+
+DCCP_SOCKOPT_SERVER_TIMEWAIT enables the server (listening socket) to hold
+timewait state when closing the connection (RFC 4340, 8.3). The usual case is
+that the closing server sends a CloseReq, whereupon the client holds timewait
+state. When this boolean socket option is on, the server sends a Close instead
+and will enter TIMEWAIT. This option must be set after accept() returns.
+
 DCCP_SOCKOPT_SEND_CSCOV and DCCP_SOCKOPT_RECV_CSCOV are used for setting the
 partial checksum coverage (RFC 4340, sec. 9.2). The default is that checksums
 always cover the entire packet and that only fully covered application data is
@@ -109,20 +133,12 @@ retries2
        importance for retransmitted acknowledgments and feature negotiation,
        data packets are never retransmitted. Analogue of tcp_retries2.
 
-send_ndp = 1
-       Whether or not to send NDP count options (sec. 7.7.2).
-
-send_ackvec = 1
-       Whether or not to send Ack Vector options (sec. 11.5).
-
-ack_ratio = 2
-       The default Ack Ratio (sec. 11.3) to use.
-
 tx_ccid = 2
-       Default CCID for the sender-receiver half-connection.
+       Default CCID for the sender-receiver half-connection. Depending on the
+       choice of CCID, the Send Ack Vector feature is enabled automatically.
 
 rx_ccid = 2
-       Default CCID for the receiver-sender half-connection.
+       Default CCID for the receiver-sender half-connection; see tx_ccid.
 
 seq_window = 100
        The initial sequence window (sec. 7.5.2).