SPARC Sparc architecture is enabled.
SWSUSP Software suspend (hibernation) is enabled.
SUSPEND System suspend states are enabled.
+ FTRACE Function tracing enabled.
TS Appropriate touchscreen support is enabled.
+ UMS USB Mass Storage support is enabled.
USB USB support is enabled.
USBHID USB Human Interface Device support is enabled.
V4L Video For Linux support is enabled.
ht -- run only enough ACPI to enable Hyper Threading
strict -- Be less tolerant of platforms that are not
strictly ACPI specification compliant.
+ rsdt -- prefer RSDT over (default) XSDT
See also Documentation/power/pm.txt, pci=noacpi
acpi_sleep= [HW,ACPI] Sleep options
Format: { s3_bios, s3_mode, s3_beep, s4_nohwsig,
old_ordering, s4_nonvs }
- See Documentation/power/video.txt for s3_bios and s3_mode.
+ See Documentation/power/video.txt for information on
+ s3_bios and s3_mode.
s3_beep is for debugging; it makes the PC's speaker beep
as soon as the kernel's real-mode entry point is called.
s4_nohwsig prevents ACPI hardware signature from being
used during resume from hibernation.
old_ordering causes the ACPI 1.0 ordering of the _PTS
- control method, wrt putting devices into low power
- states, to be enforced (the ACPI 2.0 ordering of _PTS is
- used by default).
+ control method, with respect to putting devices into
+ low power states, to be enforced (the ACPI 2.0 ordering
+ of _PTS is used by default).
s4_nonvs prevents the kernel from saving/restoring the
ACPI NVS memory during hibernation.
acpi_skip_timer_override [HW,ACPI]
Recognize and ignore IRQ0/pin2 Interrupt Override.
For broken nForce2 BIOS resulting in XT-PIC timer.
- acpi_use_timer_override [HW,ACPI}
+ acpi_use_timer_override [HW,ACPI]
Use timer override. For some broken Nvidia NF5 boards
that require a timer override, but don't have
HPET
Bits in debug_level correspond to a level in
ACPI_DEBUG_PRINT statements, e.g.,
ACPI_DEBUG_PRINT((ACPI_DB_INFO, ...
- See Documentation/acpi/debug.txt for more information
- about debug layers and levels.
+ The debug_level mask defaults to "info". See
+ Documentation/acpi/debug.txt for more information about
+ debug layers and levels.
+ Enable processor driver info messages:
+ acpi.debug_layer=0x20000000
+ Enable PCI/PCI interrupt routing info messages:
+ acpi.debug_layer=0x400000
Enable AML "Debug" output, i.e., stores to the Debug
object while interpreting AML:
acpi.debug_layer=0xffffffff acpi.debug_level=0x2
- Enable PCI/PCI interrupt routing info messages:
- acpi.debug_layer=0x400000 acpi.debug_level=0x4
Enable all messages related to ACPI hardware:
acpi.debug_layer=0x2 acpi.debug_level=0xffffffff
clearcpuid=BITNUM [X86]
Disable CPUID feature X for the kernel. See
- include/asm-x86/cpufeature.h for the valid bit numbers.
- Note the Linux specific bits are not necessarily
+ arch/x86/include/asm/cpufeature.h for the valid bit
+ numbers. Note the Linux specific bits are not necessarily
stable over kernel options, but the vendor specific
ones should be.
Also note that user programs calling CPUID directly
not work reliably with all consoles, but is known
to work with serial and VGA consoles.
+ coredump_filter=
+ [KNL] Change the default value for
+ /proc/<pid>/coredump_filter.
+ See also Documentation/filesystems/proc.txt.
+
cpcihp_generic= [HW,PCI] Generic port I/O CompactPCI driver
Format:
<first_slot>,<last_slot>,<port>,<enum_bit>[,<debug>]
a memory unit (amount[KMG]). See also
Documentation/kdump/kdump.txt for a example.
- cs4232= [HW,OSS]
- Format: <io>,<irq>,<dma>,<dma2>,<mpuio>,<mpuirq>
-
cs89x0_dma= [HW,NET]
Format: <dma>
Default value is 0.
Value can be changed at runtime via /selinux/enforce.
- es1371= [HW,OSS]
- Format: <spdif>,[<nomix>,[<amplifier>]]
- See also header of sound/oss/es1371.c.
-
ether= [HW,NET] Ethernet cards parameters
This option is obsoleted by the "netdev=" option, which
has equivalent usage. See its documentation for details.
parameter will force ia64_sal_cache_flush to call
ia64_pal_cache_flush instead of SAL_CACHE_FLUSH.
+ ftrace=[tracer]
+ [ftrace] will set and start the specified tracer
+ as early as possible in order to facilitate early
+ boot debugging.
+
+ ftrace_dump_on_oops
+ [ftrace] will dump the trace buffers on oops.
+
gamecon.map[2|3]=
[HW,JOY] Multisystem joystick and NES/SNES/PSX pad
support via parallel port (up to 5 devices per port)
hlt [BUGS=ARM,SH]
+ hvc_iucv= [S390] Number of z/VM IUCV hypervisor console (HVC)
+ terminal devices. Valid values: 0..8
+
i8042.debug [HW] Toggle i8042 debug mode
i8042.direct [HW] Put keyboard port into non-translated mode
i8042.dumbkbd [HW] Pretend that controller can only read data from
See Documentation/ide/ide.txt.
idle= [X86]
- Format: idle=poll or idle=mwait, idle=halt, idle=nomwait
- Poll forces a polling idle loop that can slightly improves the performance
- of waking up a idle CPU, but will use a lot of power and make the system
- run hot. Not recommended.
- idle=mwait. On systems which support MONITOR/MWAIT but the kernel chose
- to not use it because it doesn't save as much power as a normal idle
- loop use the MONITOR/MWAIT idle loop anyways. Performance should be the same
- as idle=poll.
- idle=halt. Halt is forced to be used for CPU idle.
+ Format: idle=poll, idle=mwait, idle=halt, idle=nomwait
+ Poll forces a polling idle loop that can slightly
+ improve the performance of waking up a idle CPU, but
+ will use a lot of power and make the system run hot.
+ Not recommended.
+ idle=mwait: On systems which support MONITOR/MWAIT but
+ the kernel chose to not use it because it doesn't save
+ as much power as a normal idle loop, use the
+ MONITOR/MWAIT idle loop anyways. Performance should be
+ the same as idle=poll.
+ idle=halt: Halt is forced to be used for CPU idle.
In such case C2/C3 won't be used again.
- idle=nomwait. Disable mwait for CPU C-states
+ idle=nomwait: Disable mwait for CPU C-states
ide-pci-generic.all-generic-ide [HW] (E)IDE subsystem
Claim all unknown PCI IDE storage controllers.
inttest= [IA64]
+ iomem= Disable strict checking of access to MMIO memory
+ strict regions from userspace.
+ relaxed
+
iommu= [x86]
off
force
lapic [X86-32,APIC] Enable the local APIC even if BIOS
disabled it.
- lapic_timer_c2_ok [X86-32,x86-64,APIC] trust the local apic timer in
- C2 power state.
+ lapic_timer_c2_ok [X86-32,x86-64,APIC] trust the local apic timer
+ in C2 power state.
libata.dma= [LIBATA] DMA control
libata.dma=0 Disable all PATA and SATA DMA
If there are multiple matching configurations changing
the same attribute, the last one is used.
+ lmb=debug [KNL] Enable lmb debug messages.
+
load_ramdisk= [RAM] List of ramdisks to load from floppy
See Documentation/blockdev/ramdisk.txt.
when a NMI is triggered.
Format: [state][,regs][,debounce][,die]
- nmi_watchdog= [KNL,BUGS=X86-32] Debugging features for SMP kernels
+ nmi_watchdog= [KNL,BUGS=X86-32,X86-64] Debugging features for SMP kernels
+ Format: [panic,][num]
+ Valid num: 0,1,2
+ 0 - turn nmi_watchdog off
+ 1 - use the IO-APIC timer for the NMI watchdog
+ 2 - use the local APIC for the NMI watchdog using
+ a performance counter. Note: This will use one performance
+ counter and the local APIC's performance vector.
+ When panic is specified panic when an NMI watchdog timeout occurs.
+ This is useful when you use a panic=... timeout and need the box
+ quickly up again.
+ Instead of 1 and 2 it is possible to use the following
+ symbolic names: lapic and ioapic
+ Example: nmi_watchdog=2 or nmi_watchdog=panic,lapic
no387 [BUGS=X86-32] Tells the kernel to use the 387 maths
emulation library even if a 387 maths coprocessor
instruction doesn't work correctly and not to
use it.
+ no_file_caps Tells the kernel not to honor file capabilities. The
+ only way then for a file to be executed with privilege
+ is to be setuid root or executed by root.
+
nohalt [IA-64] Tells the kernel not to use the power saving
function PAL_HALT_LIGHT when idle. This increases
power-consumption. On the positive side, it reduces
nosoftlockup [KNL] Disable the soft-lockup detector.
+ noswapaccount [KNL] Disable accounting of swap in memory resource
+ controller. (See Documentation/controllers/memory.txt)
+
nosync [HW,M68K] Disables sync negotiation for all devices.
notsc [BUGS=X86-32] Disable Time Stamp Counter
nr_uarts= [SERIAL] maximum number of UARTs to be registered.
+ ohci1394_dma=early [HW] enable debugging via the ohci1394 driver.
+ See Documentation/debugging-via-ohci1394.txt for more
+ info.
+
olpc_ec_timeout= [OLPC] ms delay when issuing EC commands
Rather than timing out after 20 ms if an EC
command is not properly ACKed, override the length
nomsi [MSI] If the PCI_MSI kernel config parameter is
enabled, this kernel boot option can be used to
disable the use of MSI interrupts system-wide.
+ noioapicquirk [APIC] Disable all boot interrupt quirks.
+ Safety option to keep boot IRQs enabled. This
+ should never be necessary.
+ ioapicreroute [APIC] Enable rerouting of boot IRQs to the
+ primary IO-APIC for bridges that cannot disable
+ boot IRQs. This fixes a source of spurious IRQs
+ when the system masks IRQs.
+ noioapicreroute [APIC] Disable workaround that uses the
+ boot IRQ equivalent of an IRQ that connects to
+ a chipset where boot IRQs cannot be disabled.
+ The opposite of ioapicreroute.
biosirq [X86-32] Use PCI BIOS calls to get the interrupt
routing table. These calls are known to be buggy
on several machines and they hang the machine
autoconfiguration.
Ranges are in pairs (memory base and size).
- dynamic_printk
- Enables pr_debug()/dev_dbg() calls if
- CONFIG_DYNAMIC_PRINTK_DEBUG has been enabled. These can also
- be switched on/off via <debugfs>/dynamic_printk/modules
+ dynamic_printk Enables pr_debug()/dev_dbg() calls if
+ CONFIG_DYNAMIC_PRINTK_DEBUG has been enabled.
+ These can also be switched on/off via
+ <debugfs>/dynamic_printk/modules
print-fatal-signals=
[KNL] debug: print fatal signals
reboot= [BUGS=X86-32,BUGS=ARM,BUGS=IA-64] Rebooting mode
Format: <reboot_mode>[,<reboot_mode2>[,...]]
- See arch/*/kernel/reboot.c or arch/*/kernel/process.c
+ See arch/*/kernel/reboot.c or arch/*/kernel/process.c
relax_domain_level=
[KNL, SMP] Set scheduler's default relax_domain_level.
st= [HW,SCSI] SCSI tape parameters (buffers, etc.)
See Documentation/scsi/st.txt.
+ stacktrace [FTRACE]
+ Enabled the stack tracer on boot up.
+
sti= [PARISC,HW]
Format: <num>
Set the STI (builtin display/keyboard on the HP-PARISC
thermal.psv= [HW,ACPI]
-1: disable all passive trip points
- <degrees C>: override all passive trip points to this value
+ <degrees C>: override all passive trip points to this
+ value
thermal.tzp= [HW,ACPI]
Specify global default ACPI thermal zone polling rate
See comment before function dc390_setup() in
drivers/scsi/tmscsim.c.
+ topology= [S390]
+ Format: {off | on}
+ Specify if the kernel should make use of the cpu
+ topology informations if the hardware supports these.
+ The scheduler will make use of these informations and
+ e.g. base its process migration decisions on it.
+ Default is off.
+
tp720= [HW,PS2]
trix= [HW,OSS] MediaTrix AudioTrix Pro
Format:
<io>,<irq>,<dma>,<dma2>,<sb_io>,<sb_irq>,<sb_dma>,<mpu_io>,<mpu_irq>
+ tsc= Disable clocksource-must-verify flag for TSC.
+ Format: <string>
+ [x86] reliable: mark tsc clocksource as reliable, this
+ disables clocksource verification at runtime.
+ Used to enable high-resolution timer mode on older
+ hardware, and in virtualized environment.
+
turbografx.map[2|3]= [HW,JOY]
TurboGraFX parallel port interface
Format:
usbhid.mousepoll=
[USBHID] The interval which mice are to be polled at.
+ usb-storage.delay_use=
+ [UMS] The delay in seconds before a new device is
+ scanned for Logical Units (default 5).
+
+ usb-storage.quirks=
+ [UMS] A list of quirks entries to supplement or
+ override the built-in unusual_devs list. List
+ entries are separated by commas. Each entry has
+ the form VID:PID:Flags where VID and PID are Vendor
+ and Product ID values (4-digit hex numbers) and
+ Flags is a set of characters, each corresponding
+ to a common usb-storage quirk flag as follows:
+ a = SANE_SENSE (collect more than 18 bytes
+ of sense data);
+ c = FIX_CAPACITY (decrease the reported
+ device capacity by one sector);
+ h = CAPACITY_HEURISTICS (decrease the
+ reported device capacity by one
+ sector if the number is odd);
+ i = IGNORE_DEVICE (don't bind to this
+ device);
+ l = NOT_LOCKABLE (don't try to lock and
+ unlock ejectable media);
+ m = MAX_SECTORS_64 (don't transfer more
+ than 64 sectors = 32 KB at a time);
+ o = CAPACITY_OK (accept the capacity
+ reported by the device);
+ r = IGNORE_RESIDUE (the device reports
+ bogus residue values);
+ s = SINGLE_LUN (the device has only one
+ Logical Unit);
+ w = NO_WP_DETECT (don't test whether the
+ medium is write-protected).
+ Example: quirks=0419:aaf5:rl,0421:0433:rc
+
add_efi_memmap [EFI; x86-32,X86-64] Include EFI memory map in
kernel's map of available physical RAM.
Format:
<irq>,<irq_mask>,<io>,<full_duplex>,<do_sound>,<lockup_hack>[,<irq2>[,<irq3>[,<irq4>]]]
- norandmaps Don't use address space randomization
- Equivalent to echo 0 > /proc/sys/kernel/randomize_va_space
+ norandmaps Don't use address space randomization. Equivalent to
+ echo 0 > /proc/sys/kernel/randomize_va_space
______________________________________________________________________
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff