ISAPNP ISA PnP code is enabled.
ISDN Appropriate ISDN support is enabled.
JOY Appropriate joystick support is enabled.
+ KMEMTRACE kmemtrace is enabled.
LIBATA Libata driver is enabled
LP Printer support is enabled.
LOOP Loopback device support is enabled.
ht -- run only enough ACPI to enable Hyper Threading
strict -- Be less tolerant of platforms that are not
strictly ACPI specification compliant.
+ rsdt -- prefer RSDT over (default) XSDT
See also Documentation/power/pm.txt, pci=noacpi
default: 0
acpi_sleep= [HW,ACPI] Sleep options
- Format: { s3_bios, s3_mode, s3_beep, s4_nohwsig, old_ordering }
- See Documentation/power/video.txt for s3_bios and s3_mode.
+ Format: { s3_bios, s3_mode, s3_beep, s4_nohwsig,
+ old_ordering, s4_nonvs }
+ See Documentation/power/video.txt for information on
+ s3_bios and s3_mode.
s3_beep is for debugging; it makes the PC's speaker beep
as soon as the kernel's real-mode entry point is called.
s4_nohwsig prevents ACPI hardware signature from being
used during resume from hibernation.
old_ordering causes the ACPI 1.0 ordering of the _PTS
- control method, wrt putting devices into low power
- states, to be enforced (the ACPI 2.0 ordering of _PTS is
- used by default).
+ control method, with respect to putting devices into
+ low power states, to be enforced (the ACPI 2.0 ordering
+ of _PTS is used by default).
+ s4_nonvs prevents the kernel from saving/restoring the
+ ACPI NVS memory during hibernation.
acpi_sci= [HW,ACPI] ACPI System Control Interrupt trigger mode
Format: { level | edge | high | low }
acpi_skip_timer_override [HW,ACPI]
Recognize and ignore IRQ0/pin2 Interrupt Override.
For broken nForce2 BIOS resulting in XT-PIC timer.
- acpi_use_timer_override [HW,ACPI}
+ acpi_use_timer_override [HW,ACPI]
Use timer override. For some broken Nvidia NF5 boards
that require a timer override, but don't have
HPET
hlt [BUGS=ARM,SH]
- hvc_iucv= [S390] Number of z/VM IUCV Hypervisor console (HVC)
- back-ends. Valid parameters: 0..8
+ hvc_iucv= [S390] Number of z/VM IUCV hypervisor console (HVC)
+ terminal devices. Valid values: 0..8
i8042.debug [HW] Toggle i8042 debug mode
i8042.direct [HW] Put keyboard port into non-translated mode
See Documentation/ide/ide.txt.
idle= [X86]
- Format: idle=poll or idle=mwait, idle=halt, idle=nomwait
- Poll forces a polling idle loop that can slightly improves the performance
- of waking up a idle CPU, but will use a lot of power and make the system
- run hot. Not recommended.
- idle=mwait. On systems which support MONITOR/MWAIT but the kernel chose
- to not use it because it doesn't save as much power as a normal idle
- loop use the MONITOR/MWAIT idle loop anyways. Performance should be the same
- as idle=poll.
- idle=halt. Halt is forced to be used for CPU idle.
+ Format: idle=poll, idle=mwait, idle=halt, idle=nomwait
+ Poll forces a polling idle loop that can slightly
+ improve the performance of waking up a idle CPU, but
+ will use a lot of power and make the system run hot.
+ Not recommended.
+ idle=mwait: On systems which support MONITOR/MWAIT but
+ the kernel chose to not use it because it doesn't save
+ as much power as a normal idle loop, use the
+ MONITOR/MWAIT idle loop anyways. Performance should be
+ the same as idle=poll.
+ idle=halt: Halt is forced to be used for CPU idle.
In such case C2/C3 won't be used again.
- idle=nomwait. Disable mwait for CPU C-states
+ idle=nomwait: Disable mwait for CPU C-states
ide-pci-generic.all-generic-ide [HW] (E)IDE subsystem
Claim all unknown PCI IDE storage controllers.
use the HighMem zone if it exists, and the Normal
zone if it does not.
+ kmemtrace.enable= [KNL,KMEMTRACE] Format: { yes | no }
+ Controls whether kmemtrace is enabled
+ at boot-time.
+
+ kmemtrace.subbufs=n [KNL,KMEMTRACE] Overrides the number of
+ subbufs kmemtrace's relay channel has. Set this
+ higher than default (KMEMTRACE_N_SUBBUFS in code) if
+ you experience buffer overruns.
+
movablecore=nn[KMG] [KNL,X86-32,IA-64,PPC,X86-64] This parameter
is similar to kernelcore except it specifies the
amount of memory used for migratable allocations.
lapic [X86-32,APIC] Enable the local APIC even if BIOS
disabled it.
- lapic_timer_c2_ok [X86-32,x86-64,APIC] trust the local apic timer in
- C2 power state.
+ lapic_timer_c2_ok [X86-32,x86-64,APIC] trust the local apic timer
+ in C2 power state.
libata.dma= [LIBATA] DMA control
libata.dma=0 Disable all PATA and SATA DMA
nosoftlockup [KNL] Disable the soft-lockup detector.
+ noswapaccount [KNL] Disable accounting of swap in memory resource
+ controller. (See Documentation/controllers/memory.txt)
+
nosync [HW,M68K] Disables sync negotiation for all devices.
notsc [BUGS=X86-32] Disable Time Stamp Counter
thermal.psv= [HW,ACPI]
-1: disable all passive trip points
- <degrees C>: override all passive trip points to this value
+ <degrees C>: override all passive trip points to this
+ value
thermal.tzp= [HW,ACPI]
Specify global default ACPI thermal zone polling rate
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff