ixgbevf: Kconfig, Makefile and Documentation

[safe/jmp/linux-2.6] / Documentation / kernel-parameters.txt

diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt
index fce5b5e..5ba4d9d 100644 (file)
--- a/Documentation/kernel-parameters.txt
+++ b/Documentation/kernel-parameters.txt
@@ -1032,7 +1032,7 @@ and is between 256 and 4096 characters. It is defined in the file
                        No delay
 
        ip=             [IP_PNP]
-                       See Documentation/filesystems/nfsroot.txt.
+                       See Documentation/filesystems/nfs/nfsroot.txt.
 
        ip2=            [HW] Set IO/IRQ pairs for up to 4 IntelliPort boards
                        See comment before ip2_setup() in
@@ -1553,10 +1553,10 @@ and is between 256 and 4096 characters. It is defined in the file
                        going to be removed in 2.6.29.
 
        nfsaddrs=       [NFS]
-                       See Documentation/filesystems/nfsroot.txt.
+                       See Documentation/filesystems/nfs/nfsroot.txt.
 
        nfsroot=        [NFS] nfs root filesystem for disk-less boxes.
-                       See Documentation/filesystems/nfsroot.txt.
+                       See Documentation/filesystems/nfs/nfsroot.txt.
 
        nfs.callback_tcpport=
                        [NFS] set the TCP port on which the NFSv4 callback
@@ -1787,6 +1787,11 @@ and is between 256 and 4096 characters. It is defined in the file
                        waiting for the ACK, so if this is set too high
                        interrupts *may* be lost!
 
+       omap_mux=       [OMAP] Override bootloader pin multiplexing.
+                       Format: <mux_mode0.mode_name=value>...
+                       For example, to override I2C bus2:
+                       omap_mux=i2c2_scl.i2c2_scl=0x100,i2c2_sda.i2c2_sda=0x100
+
        opl3=           [HW,OSS]
                        Format: <io>
 
@@ -2605,6 +2610,9 @@ and is between 256 and 4096 characters. It is defined in the file
        uart6850=       [HW,OSS]
                        Format: <io>,<irq>
 
+       uhash_entries=  [KNL,NET]
+                       Set number of hash buckets for UDP/UDP-Lite connections
+
        uhci-hcd.ignore_oc=
                        [USB] Ignore overcurrent events (default N).
                        Some badly-designed motherboards generate lots of
@@ -2660,6 +2668,8 @@ and is between 256 and 4096 characters. It is defined in the file
                        to a common usb-storage quirk flag as follows:
                                a = SANE_SENSE (collect more than 18 bytes
                                        of sense data);
+                               b = BAD_SENSE (don't collect more than 18
+                                       bytes of sense data);
                                c = FIX_CAPACITY (decrease the reported
                                        device capacity by one sector);
                                h = CAPACITY_HEURISTICS (decrease the
@@ -2719,6 +2729,11 @@ and is between 256 and 4096 characters. It is defined in the file
        vmpoff=         [KNL,S390] Perform z/VM CP command after power off.
                        Format: <command>
 
+       vt.cur_default= [VT] Default cursor shape.
+                       Format: 0xCCBBAA, where AA, BB, and CC are the same as
+                       the parameters of the <Esc>[?A;B;Cc escape sequence;
+                       see VGA-softcursor.txt. Default: 2 = underline.
+
        vt.default_blu= [VT]
                        Format: <blue0>,<blue1>,<blue2>,...,<blue15>
                        Change the default blue palette of the console.
@@ -2744,6 +2759,15 @@ and is between 256 and 4096 characters. It is defined in the file
                        Default is 1, i.e. UTF-8 mode is enabled for all
                        newly opened terminals.
 
+       vt.global_cursor_default=
+                       [VT]
+                       Format=<-1|0|1>
+                       Set system-wide default for whether a cursor
+                       is shown on new VTs. Default is -1,
+                       i.e. cursors will be created by default unless
+                       overridden by individual drivers. 0 will hide
+                       cursors, 1 will display them.
+
        waveartist=     [HW,OSS]
                        Format: <io>,<irq>,<dma>,<dma2>