IMA Integrity measurement architecture is enabled.
IOSCHED More than one I/O scheduler is enabled.
IP_PNP IP DHCP, BOOTP, or RARP is enabled.
+ IPV6 IPv6 support is enabled.
ISAPNP ISA PnP code is enabled.
ISDN Appropriate ISDN support is enabled.
JOY Appropriate joystick support is enabled.
acpi_display_output=video
See above.
+ acpi_early_pdc_eval [HW,ACPI] Evaluate processor _PDC methods
+ early. Needed on some platforms to properly
+ initialize the EC.
+
acpi_irq_balance [HW,ACPI]
ACPI will balance active IRQs
default in APIC mode
acpi_sleep= [HW,ACPI] Sleep options
Format: { s3_bios, s3_mode, s3_beep, s4_nohwsig,
- old_ordering, s4_nonvs }
+ old_ordering, s4_nonvs, sci_force_enable }
See Documentation/power/video.txt for information on
s3_bios and s3_mode.
s3_beep is for debugging; it makes the PC's speaker beep
of _PTS is used by default).
s4_nonvs prevents the kernel from saving/restoring the
ACPI NVS memory during hibernation.
+ sci_force_enable causes the kernel to set SCI_EN directly
+ on resume from S1/S3 (which is against the ACPI spec,
+ but some broken systems don't work without it).
acpi_use_timer_override [HW,ACPI]
Use timer override. For some broken Nvidia NF5 boards
aic79xx= [HW,SCSI]
See Documentation/scsi/aic79xx.txt.
+ alignment= [KNL,ARM]
+ Allow the default userspace alignment fault handler
+ behaviour to be specified. Bit 0 enables warnings,
+ bit 1 enables fixups, and bit 2 sends a segfault.
+
amd_iommu= [HW,X86-84]
Pass parameters to the AMD IOMMU driver in the system.
Possible values are:
Change the amount of debugging information output
when initialising the APIC and IO-APIC components.
+ autoconf= [IPV6]
+ See Documentation/networking/ipv6.txt.
+
show_lapic= [APIC,X86] Advanced Programmable Interrupt Controller
Limit apic dumping. The parameter defines the maximal
number of local apics being dumped. Also it is possible
See drivers/char/README.epca and
Documentation/serial/digiepca.txt.
+ disable= [IPV6]
+ See Documentation/networking/ipv6.txt.
+
+ disable_ipv6= [IPV6]
+ See Documentation/networking/ipv6.txt.
+
disable_mtrr_cleanup [X86]
The kernel tries to adjust MTRR layout from continuous
to discrete, to make X server driver able to add WB
No delay
ip= [IP_PNP]
- See Documentation/filesystems/nfsroot.txt.
+ See Documentation/filesystems/nfs/nfsroot.txt.
ip2= [HW] Set IO/IRQ pairs for up to 4 IntelliPort boards
See comment before ip2_setup() in
going to be removed in 2.6.29.
nfsaddrs= [NFS]
- See Documentation/filesystems/nfsroot.txt.
+ See Documentation/filesystems/nfs/nfsroot.txt.
nfsroot= [NFS] nfs root filesystem for disk-less boxes.
- See Documentation/filesystems/nfsroot.txt.
+ See Documentation/filesystems/nfs/nfsroot.txt.
nfs.callback_tcpport=
[NFS] set the TCP port on which the NFSv4 callback
nomfgpt [X86-32] Disable Multi-Function General Purpose
Timer usage (for AMD Geode machines).
+ nopat [X86] Disable PAT (page attribute table extension of
+ pagetables) support.
+
norandmaps Don't use address space randomization. Equivalent to
echo 0 > /proc/sys/kernel/randomize_va_space
purges which is reported from either PAL_VM_SUMMARY or
SAL PALO.
+ nr_cpus= [SMP] Maximum number of processors that an SMP kernel
+ could support. nr_cpus=n : n >= 1 limits the kernel to
+ supporting 'n' processors. Later in runtime you can not
+ use hotplug cpu feature to put more cpu back to online.
+ just like you compile the kernel NR_CPUS=n
+
nr_uarts= [SERIAL] maximum number of UARTs to be registered.
numa_zonelist_order= [KNL, BOOT] Select zonelist order for NUMA.
IRQ routing is enabled.
noacpi [X86] Do not use ACPI for IRQ routing
or for PCI scanning.
- use_crs [X86] Use _CRS for PCI resource
- allocation.
+ use_crs [X86] Use PCI host bridge window information
+ from ACPI. On BIOSes from 2008 or later, this
+ is enabled by default. If you need to use this,
+ please report a bug.
+ nocrs [X86] Ignore PCI host bridge windows from ACPI.
+ If you need to use this, please report a bug.
routeirq Do IRQ routing for all PCI devices.
This is normally done in pci_enable_device(),
so this option is a temporary workaround
force Enable ASPM even on devices that claim not to support it.
WARNING: Forcing ASPM on may cause system lockups.
+ pcie_pme= [PCIE,PM] Native PCIe PME signaling options:
+ off Do not use native PCIe PME signaling.
+ force Use native PCIe PME signaling even if the BIOS refuses
+ to allow the kernel to control the relevant PCIe config
+ registers.
+ nomsi Do not use MSI for native PCIe PME signaling (this makes
+ all PCIe root ports use INTx for everything).
+
pcmv= [HW,PCMCIA] BadgePAD 4
pd. [PARIDE]
medium is write-protected).
Example: quirks=0419:aaf5:rl,0421:0433:rc
+ userpte=
+ [X86] Flags controlling user PTE allocations.
+
+ nohigh = do not allocate PTE pages in
+ HIGHMEM regardless of setting
+ of CONFIG_HIGHPTE.
+
vdso= [X86,SH]
vdso=2: enable compat VDSO (default with COMPAT_VDSO)
vdso=1: enable VDSO (default)
default x2apic cluster mode on platforms
supporting x2apic.
+ x86_mrst_timer= [X86-32,APBT]
+ Choose timer option for x86 Moorestown MID platform.
+ Two valid options are apbt timer only and lapic timer
+ plus one apbt timer for broadcast timer.
+ x86_mrst_timer=apbt_only | lapic_and_apbt
+
xd= [HW,XT] Original XT pre-IDE (RLL encoded) disks.
xd_geo= See header of drivers/block/xd.c.
git://ftp.safe.ca / safe / jmp / linux-2.6 / blobdiff