SAFE public projects git trees. - safe/jmp/linux-2.6/blob - drivers/input/touchscreen/atmel-wm97xx.c

   1 /*
   2  * Atmel AT91 and AVR32 continuous touch screen driver for Wolfson WM97xx AC97
   3  * codecs.
   4  *
   5  * Copyright (C) 2008 - 2009 Atmel Corporation
   6  *
   7  * This program is free software; you can redistribute it and/or modify it
   8  * under the terms of the GNU General Public License version 2 as published by
   9  * the Free Software Foundation.
  10  */
  11 #include <linux/module.h>
  12 #include <linux/moduleparam.h>
  13 #include <linux/kernel.h>
  14 #include <linux/init.h>
  15 #include <linux/delay.h>
  16 #include <linux/irq.h>
  17 #include <linux/interrupt.h>
  18 #include <linux/wm97xx.h>
  19 #include <linux/timer.h>
  20 #include <linux/gpio.h>
  21 #include <linux/io.h>
  22
  23 #define AC97C_ICA               0x10
  24 #define AC97C_CBRHR             0x30
  25 #define AC97C_CBSR              0x38
  26 #define AC97C_CBMR              0x3c
  27 #define AC97C_IER               0x54
  28 #define AC97C_IDR               0x58
  29
  30 #define AC97C_RXRDY             (1 << 4)
  31 #define AC97C_OVRUN             (1 << 5)
  32
  33 #define AC97C_CMR_SIZE_20       (0 << 16)
  34 #define AC97C_CMR_SIZE_18       (1 << 16)
  35 #define AC97C_CMR_SIZE_16       (2 << 16)
  36 #define AC97C_CMR_SIZE_10       (3 << 16)
  37 #define AC97C_CMR_CEM_LITTLE    (1 << 18)
  38 #define AC97C_CMR_CEM_BIG       (0 << 18)
  39 #define AC97C_CMR_CENA          (1 << 21)
  40
  41 #define AC97C_INT_CBEVT         (1 << 4)
  42
  43 #define AC97C_SR_CAEVT          (1 << 3)
  44
  45 #define AC97C_CH_MASK(slot)                                             \
  46         (0x7 << (3 * (slot - 3)))
  47 #define AC97C_CH_ASSIGN(slot, channel)                                  \
  48         (AC97C_CHANNEL_##channel << (3 * (slot - 3)))
  49 #define AC97C_CHANNEL_NONE      0x0
  50 #define AC97C_CHANNEL_B         0x2
  51
  52 #define ac97c_writel(chip, reg, val)                    \
  53         __raw_writel((val), (chip)->regs + AC97C_##reg)
  54 #define ac97c_readl(chip, reg)                          \
  55         __raw_readl((chip)->regs + AC97C_##reg)
  56
  57 #ifdef CONFIG_CPU_AT32AP700X
  58 #define ATMEL_WM97XX_AC97C_IOMEM        (0xfff02800)
  59 #define ATMEL_WM97XX_AC97C_IRQ          (29)
  60 #define ATMEL_WM97XX_GPIO_DEFAULT       (32+16) /* Pin 16 on port B. */
  61 #else
  62 #error Unknown CPU, this driver only supports AT32AP700X CPUs.
  63 #endif
  64
  65 struct continuous {
  66         u16 id;    /* codec id */
  67         u8 code;   /* continuous code */
  68         u8 reads;  /* number of coord reads per read cycle */
  69         u32 speed; /* number of coords per second */
  70 };
  71
  72 #define WM_READS(sp) ((sp / HZ) + 1)
  73
  74 static const struct continuous cinfo[] = {
  75         {WM9705_ID2, 0, WM_READS(94), 94},
  76         {WM9705_ID2, 1, WM_READS(188), 188},
  77         {WM9705_ID2, 2, WM_READS(375), 375},
  78         {WM9705_ID2, 3, WM_READS(750), 750},
  79         {WM9712_ID2, 0, WM_READS(94), 94},
  80         {WM9712_ID2, 1, WM_READS(188), 188},
  81         {WM9712_ID2, 2, WM_READS(375), 375},
  82         {WM9712_ID2, 3, WM_READS(750), 750},
  83         {WM9713_ID2, 0, WM_READS(94), 94},
  84         {WM9713_ID2, 1, WM_READS(120), 120},
  85         {WM9713_ID2, 2, WM_READS(154), 154},
  86         {WM9713_ID2, 3, WM_READS(188), 188},
  87 };
  88
  89 /* Continuous speed index. */
  90 static int sp_idx;
  91
  92 /*
  93  * Pen sampling frequency (Hz) in continuous mode.
  94  */
  95 static int cont_rate = 188;
  96 module_param(cont_rate, int, 0);
  97 MODULE_PARM_DESC(cont_rate, "Sampling rate in continuous mode (Hz)");
  98
  99 /*
 100  * Pen down detection.
 101  *
 102  * This driver can either poll or use an interrupt to indicate a pen down
 103  * event. If the irq request fails then it will fall back to polling mode.
 104  */
 105 static int pen_int = 1;
 106 module_param(pen_int, int, 0);
 107 MODULE_PARM_DESC(pen_int, "Pen down detection (1 = interrupt, 0 = polling)");
 108
 109 /*
 110  * Pressure readback.
 111  *
 112  * Set to 1 to read back pen down pressure.
 113  */
 114 static int pressure;
 115 module_param(pressure, int, 0);
 116 MODULE_PARM_DESC(pressure, "Pressure readback (1 = pressure, 0 = no pressure)");
 117
 118 /*
 119  * AC97 touch data slot.
 120  *
 121  * Touch screen readback data ac97 slot.
 122  */
 123 static int ac97_touch_slot = 5;
 124 module_param(ac97_touch_slot, int, 0);
 125 MODULE_PARM_DESC(ac97_touch_slot, "Touch screen data slot AC97 number");
 126
 127 /*
 128  * GPIO line number.
 129  *
 130  * Set to GPIO number where the signal from the WM97xx device is hooked up.
 131  */
 132 static int atmel_gpio_line = ATMEL_WM97XX_GPIO_DEFAULT;
 133 module_param(atmel_gpio_line, int, 0);
 134 MODULE_PARM_DESC(atmel_gpio_line, "GPIO line number connected to WM97xx");
 135
 136 struct atmel_wm97xx {
 137         struct wm97xx           *wm;
 138         struct timer_list       pen_timer;
 139         void __iomem            *regs;
 140         unsigned long           ac97c_irq;
 141         unsigned long           gpio_pen;
 142         unsigned long           gpio_irq;
 143         unsigned short          x;
 144         unsigned short          y;
 145 };
 146
 147 static irqreturn_t atmel_wm97xx_channel_b_interrupt(int irq, void *dev_id)
 148 {
 149         struct atmel_wm97xx *atmel_wm97xx = dev_id;
 150         struct wm97xx *wm = atmel_wm97xx->wm;
 151         int status = ac97c_readl(atmel_wm97xx, CBSR);
 152         irqreturn_t retval = IRQ_NONE;
 153
 154         if (status & AC97C_OVRUN) {
 155                 dev_dbg(&wm->touch_dev->dev, "AC97C overrun\n");
 156                 ac97c_readl(atmel_wm97xx, CBRHR);
 157                 retval = IRQ_HANDLED;
 158         } else if (status & AC97C_RXRDY) {
 159                 u16 data;
 160                 u16 value;
 161                 u16 source;
 162                 u16 pen_down;
 163
 164                 data = ac97c_readl(atmel_wm97xx, CBRHR);
 165                 value = data & 0x0fff;
 166                 source = data & WM97XX_ADCSRC_MASK;
 167                 pen_down = (data & WM97XX_PEN_DOWN) >> 8;
 168
 169                 if (source == WM97XX_ADCSEL_X)
 170                         atmel_wm97xx->x = value;
 171                 if (source == WM97XX_ADCSEL_Y)
 172                         atmel_wm97xx->y = value;
 173
 174                 if (!pressure && source == WM97XX_ADCSEL_Y) {
 175                         input_report_abs(wm->input_dev, ABS_X, atmel_wm97xx->x);
 176                         input_report_abs(wm->input_dev, ABS_Y, atmel_wm97xx->y);
 177                         input_report_key(wm->input_dev, BTN_TOUCH, pen_down);
 178                         input_sync(wm->input_dev);
 179                 } else if (pressure && source == WM97XX_ADCSEL_PRES) {
 180                         input_report_abs(wm->input_dev, ABS_X, atmel_wm97xx->x);
 181                         input_report_abs(wm->input_dev, ABS_Y, atmel_wm97xx->y);
 182                         input_report_abs(wm->input_dev, ABS_PRESSURE, value);
 183                         input_report_key(wm->input_dev, BTN_TOUCH, value);
 184                         input_sync(wm->input_dev);
 185                 }
 186
 187                 retval = IRQ_HANDLED;
 188         }
 189
 190         return retval;
 191 }
 192
 193 static void atmel_wm97xx_acc_pen_up(struct wm97xx *wm)
 194 {
 195         struct atmel_wm97xx *atmel_wm97xx = platform_get_drvdata(wm->touch_dev);
 196         struct input_dev *input_dev = wm->input_dev;
 197         int pen_down = gpio_get_value(atmel_wm97xx->gpio_pen);
 198
 199         if (pen_down != 0) {
 200                 mod_timer(&atmel_wm97xx->pen_timer,
 201                           jiffies + msecs_to_jiffies(1));
 202         } else {
 203                 if (pressure)
 204                         input_report_abs(input_dev, ABS_PRESSURE, 0);
 205                 input_report_key(input_dev, BTN_TOUCH, 0);
 206                 input_sync(input_dev);
 207         }
 208 }
 209
 210 static void atmel_wm97xx_pen_timer(unsigned long data)
 211 {
 212         atmel_wm97xx_acc_pen_up((struct wm97xx *)data);
 213 }
 214
 215 static int atmel_wm97xx_acc_startup(struct wm97xx *wm)
 216 {
 217         struct atmel_wm97xx *atmel_wm97xx = platform_get_drvdata(wm->touch_dev);
 218         int idx = 0;
 219
 220         if (wm->ac97 == NULL)
 221                 return -ENODEV;
 222
 223         for (idx = 0; idx < ARRAY_SIZE(cinfo); idx++) {
 224                 if (wm->id != cinfo[idx].id)
 225                         continue;
 226
 227                 sp_idx = idx;
 228
 229                 if (cont_rate <= cinfo[idx].speed)
 230                         break;
 231         }
 232
 233         wm->acc_rate = cinfo[sp_idx].code;
 234         wm->acc_slot = ac97_touch_slot;
 235         dev_info(&wm->touch_dev->dev, "atmel accelerated touchscreen driver, "
 236                         "%d samples/sec\n", cinfo[sp_idx].speed);
 237
 238         if (pen_int) {
 239                 unsigned long reg;
 240
 241                 wm->pen_irq = atmel_wm97xx->gpio_irq;
 242
 243                 switch (wm->id) {
 244                 case WM9712_ID2: /* Fall through. */
 245                 case WM9713_ID2:
 246                         /*
 247                          * Use GPIO 13 (PEN_DOWN) to assert GPIO line 3
 248                          * (PENDOWN).
 249                          */
 250                         wm97xx_config_gpio(wm, WM97XX_GPIO_13, WM97XX_GPIO_IN,
 251                                         WM97XX_GPIO_POL_HIGH,
 252                                         WM97XX_GPIO_STICKY,
 253                                         WM97XX_GPIO_WAKE);
 254                         wm97xx_config_gpio(wm, WM97XX_GPIO_3, WM97XX_GPIO_OUT,
 255                                         WM97XX_GPIO_POL_HIGH,
 256                                         WM97XX_GPIO_NOTSTICKY,
 257                                         WM97XX_GPIO_NOWAKE);
 258                 case WM9705_ID2: /* Fall through. */
 259                         /*
 260                          * Enable touch data slot in AC97 controller channel B.
 261                          */
 262                         reg = ac97c_readl(atmel_wm97xx, ICA);
 263                         reg &= ~AC97C_CH_MASK(wm->acc_slot);
 264                         reg |= AC97C_CH_ASSIGN(wm->acc_slot, B);
 265                         ac97c_writel(atmel_wm97xx, ICA, reg);
 266
 267                         /*
 268                          * Enable channel and interrupt for RXRDY and OVERRUN.
 269                          */
 270                         ac97c_writel(atmel_wm97xx, CBMR, AC97C_CMR_CENA
 271                                         | AC97C_CMR_CEM_BIG
 272                                         | AC97C_CMR_SIZE_16
 273                                         | AC97C_OVRUN
 274                                         | AC97C_RXRDY);
 275                         /* Dummy read to empty RXRHR. */
 276                         ac97c_readl(atmel_wm97xx, CBRHR);
 277                         /*
 278                          * Enable interrupt for channel B in the AC97
 279                          * controller.
 280                          */
 281                         ac97c_writel(atmel_wm97xx, IER, AC97C_INT_CBEVT);
 282                         break;
 283                 default:
 284                         dev_err(&wm->touch_dev->dev, "pen down irq not "
 285                                         "supported on this device\n");
 286                         pen_int = 0;
 287                         break;
 288                 }
 289         }
 290
 291         return 0;
 292 }
 293
 294 static void atmel_wm97xx_acc_shutdown(struct wm97xx *wm)
 295 {
 296         if (pen_int) {
 297                 struct atmel_wm97xx *atmel_wm97xx =
 298                         platform_get_drvdata(wm->touch_dev);
 299                 unsigned long ica;
 300
 301                 switch (wm->id & 0xffff) {
 302                 case WM9705_ID2: /* Fall through. */
 303                 case WM9712_ID2: /* Fall through. */
 304                 case WM9713_ID2:
 305                         /* Disable slot and turn off channel B interrupts. */
 306                         ica = ac97c_readl(atmel_wm97xx, ICA);
 307                         ica &= ~AC97C_CH_MASK(wm->acc_slot);
 308                         ac97c_writel(atmel_wm97xx, ICA, ica);
 309                         ac97c_writel(atmel_wm97xx, IDR, AC97C_INT_CBEVT);
 310                         ac97c_writel(atmel_wm97xx, CBMR, 0);
 311                         wm->pen_irq = 0;
 312                         break;
 313                 default:
 314                         dev_err(&wm->touch_dev->dev, "unknown codec\n");
 315                         break;
 316                 }
 317         }
 318 }
 319
 320 static void atmel_wm97xx_irq_enable(struct wm97xx *wm, int enable)
 321 {
 322         /* Intentionally left empty. */
 323 }
 324
 325 static struct wm97xx_mach_ops atmel_mach_ops = {
 326         .acc_enabled    = 1,
 327         .acc_pen_up     = atmel_wm97xx_acc_pen_up,
 328         .acc_startup    = atmel_wm97xx_acc_startup,
 329         .acc_shutdown   = atmel_wm97xx_acc_shutdown,
 330         .irq_enable     = atmel_wm97xx_irq_enable,
 331         .irq_gpio       = WM97XX_GPIO_3,
 332 };
 333
 334 static int __init atmel_wm97xx_probe(struct platform_device *pdev)
 335 {
 336         struct wm97xx *wm = platform_get_drvdata(pdev);
 337         struct atmel_wm97xx *atmel_wm97xx;
 338         int ret;
 339
 340         atmel_wm97xx = kzalloc(sizeof(struct atmel_wm97xx), GFP_KERNEL);
 341         if (!atmel_wm97xx) {
 342                 dev_dbg(&pdev->dev, "out of memory\n");
 343                 return -ENOMEM;
 344         }
 345
 346         atmel_wm97xx->wm        = wm;
 347         atmel_wm97xx->regs      = (void *)ATMEL_WM97XX_AC97C_IOMEM;
 348         atmel_wm97xx->ac97c_irq = ATMEL_WM97XX_AC97C_IRQ;
 349         atmel_wm97xx->gpio_pen  = atmel_gpio_line;
 350         atmel_wm97xx->gpio_irq  = gpio_to_irq(atmel_wm97xx->gpio_pen);
 351
 352         setup_timer(&atmel_wm97xx->pen_timer, atmel_wm97xx_pen_timer,
 353                         (unsigned long)wm);
 354
 355         ret = request_irq(atmel_wm97xx->ac97c_irq,
 356                           atmel_wm97xx_channel_b_interrupt,
 357                           IRQF_SHARED, "atmel-wm97xx-ch-b", atmel_wm97xx);
 358         if (ret) {
 359                 dev_dbg(&pdev->dev, "could not request ac97c irq\n");
 360                 goto err;
 361         }
 362
 363         platform_set_drvdata(pdev, atmel_wm97xx);
 364
 365         ret = wm97xx_register_mach_ops(wm, &atmel_mach_ops);
 366         if (ret)
 367                 goto err_irq;
 368
 369         return ret;
 370
 371 err_irq:
 372         free_irq(atmel_wm97xx->ac97c_irq, atmel_wm97xx);
 373 err:
 374         platform_set_drvdata(pdev, NULL);
 375         kfree(atmel_wm97xx);
 376         return ret;
 377 }
 378
 379 static int __exit atmel_wm97xx_remove(struct platform_device *pdev)
 380 {
 381         struct atmel_wm97xx *atmel_wm97xx = platform_get_drvdata(pdev);
 382         struct wm97xx *wm = atmel_wm97xx->wm;
 383
 384         ac97c_writel(atmel_wm97xx, IDR, AC97C_INT_CBEVT);
 385         free_irq(atmel_wm97xx->ac97c_irq, atmel_wm97xx);
 386         del_timer_sync(&atmel_wm97xx->pen_timer);
 387         wm97xx_unregister_mach_ops(wm);
 388         platform_set_drvdata(pdev, NULL);
 389         kfree(atmel_wm97xx);
 390
 391         return 0;
 392 }
 393
 394 #ifdef CONFIG_PM
 395 static int atmel_wm97xx_suspend(struct platform_device *pdev, pm_message_t msg)
 396 {
 397         struct atmel_wm97xx *atmel_wm97xx = platform_get_drvdata(pdev);
 398
 399         ac97c_writel(atmel_wm97xx, IDR, AC97C_INT_CBEVT);
 400         disable_irq(atmel_wm97xx->gpio_irq);
 401         del_timer_sync(&atmel_wm97xx->pen_timer);
 402
 403         return 0;
 404 }
 405
 406 static int atmel_wm97xx_resume(struct platform_device *pdev)
 407 {
 408         struct atmel_wm97xx *atmel_wm97xx = platform_get_drvdata(pdev);
 409         struct wm97xx *wm = atmel_wm97xx->wm;
 410
 411         if (wm->input_dev->users) {
 412                 enable_irq(atmel_wm97xx->gpio_irq);
 413                 ac97c_writel(atmel_wm97xx, IER, AC97C_INT_CBEVT);
 414         }
 415
 416         return 0;
 417 }
 418 #else
 419 #define atmel_wm97xx_suspend    NULL
 420 #define atmel_wm97xx_resume     NULL
 421 #endif
 422
 423 static struct platform_driver atmel_wm97xx_driver = {
 424         .remove         = __exit_p(atmel_wm97xx_remove),
 425         .driver         = {
 426                 .name = "wm97xx-touch",
 427         },
 428         .suspend        = atmel_wm97xx_suspend,
 429         .resume         = atmel_wm97xx_resume,
 430 };
 431
 432 static int __init atmel_wm97xx_init(void)
 433 {
 434         return platform_driver_probe(&atmel_wm97xx_driver, atmel_wm97xx_probe);
 435 }
 436 module_init(atmel_wm97xx_init);
 437
 438 static void __exit atmel_wm97xx_exit(void)
 439 {
 440         platform_driver_unregister(&atmel_wm97xx_driver);
 441 }
 442 module_exit(atmel_wm97xx_exit);
 443
 444 MODULE_AUTHOR("Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>");
 445 MODULE_DESCRIPTION("wm97xx continuous touch driver for Atmel AT91 and AVR32");
 446 MODULE_LICENSE("GPL");