[SCSI] cxgb3i: Add cxgb3i iSCSI driver.

This patch implements the cxgb3i iscsi connection acceleration for the
open-iscsi initiator.

The cxgb3i driver offers the iscsi PDU based offload:
- digest insertion and verification
- payload direct-placement into host memory buffer.

Signed-off-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] zfcp: Remove unnecessary warning message

Remove a message that was emitted for a port that could not initially
be opened. This is a rare case when the port discovery hits an
initiator port and only confuses the user with an initator port logged
in the message. Remove the whole special case: The failed "open port"
request triggers required follow-up actions anyway.

Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Acked-by: Felix Beck <felix@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] zfcp: Add support for unchained FSF requests

Add the support to send CT and ELS requests as unchained FSF requests. This is
required for older hardware and was somehow omitted during the cleanup of the
FSF layer. The req_count and resp_count attributes are unused, so remove them
instead of adding a special case for setting them. Also add debug data and a
warning, when the ct request hits a limit.

Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Acked-by: Martin Petermann <martin@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] zfcp: Remove busid macro

With the change to the dev_ message macros, the macro to get the busid
is only used in a few places. Remove it and directly get the dev_name
from the device.

Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] zfcp: remove DID_DID flag

The port flag DID_DID indicates whether we know the current id of the
port. This is always set in parallel. Since the id 0 is invalid
(because the port id 0 is invalid) we can remove the DID_DID flag:
d_id of 0 indicates an invalid d_id != 0 is a valid one.

Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Acked-by: Felix Beck <felix@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] zfcp: Simplify mask lookups for incoming RSCNs

Use an array for looking up the mask corresponding to the 2-bit
information instead of the switch/case.

Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Acked-by: Felix Beck <felix@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] zfcp: Remove initial device data from zfcp_data

The information from the kernel parameter is only needed during init.
Keep the three pieces (busid, wwpn and lun) local to simplify the
global zfcp_data structures. While at it, also remove the unused
loglevel variable and give the module parameter variable a better
name.

Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Acked-by: Felix Beck <felix@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] zfcp: fix compile warning

Get rid of this one:

drivers/s390/scsi/zfcp_erp.c: In function 'zfcp_erp_thread':
drivers/s390/scsi/zfcp_erp.c:1400: warning: ignoring return value of
'down_interruptible', declared with attribute warn_unused_result

zfcp_erp_thread is a kernel thread which can't receive any signals.
So introduce a dummy variable and get rid of the warning.

Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] zfcp: Remove adapter list

After the latest changes, the list of FCP devices is only used to
lookup the adapter for requests from the actcli tool. Change this to
use the lookup function in the cio layer. Now we can remove the
adapter list and have one place less to use the global config_lock.

Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Acked-by: Felix Beck <felix@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] zfcp: Simplify SBAL allocation to fix sparse warnings

When waiting for a request claim the SBAL before waiting. This way,
locking before each check of the free counter is not required and
sparse does not emit warnings for the complicated locking scheme.

Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Acked-by: Felix Beck <felix@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] zfcp: register with SCSI layer on ccw registration

Synchronize the registration and de-registration with the SCSI layer
at CCW registration, de-registration. Before we registered with the
SCSI layer on adapter activation. This way the reg and de-reg process
is in balance.

Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] zfcp: Fix message line break

Move the closing parenthesis before the line break.

Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Acked-by: Felix Beck <felix@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: changes in multiq code

Following changes have been made:
 1. Scan outstanding commands only in the queue where it is submitted
 2. Update queue registers directly in the fast path
 3. Queue specific BAR is remapped only for multiq capable adapters

Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] eata: fix the data buffer accessors conversion regression

This fixes the regression introduced by the commit
58e2a02eb18393e76a469580fedf7caec190eb5e (eata: convert to use the
data buffer accessors), reported:

http://marc.info/?t=122987621300006&r=1&w=2

- fix DMA_NONE handling in map_dma()

- this driver can't use scsi_dma_map since host->shost_gendev.parent
is not set properly (it uses scsi_register).

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Reported-by: Arthur Marsh <arthur.marsh@internode.on.net>
Tested-by: Arthur Marsh <arthur.marsh@internode.on.net>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] ibmvfc: Improve async event handling

While doing various error injection testing, such as cable
pulls and target moves, some issues were observed in handling
these events. This patch improves the way these events are handled
by increasing the delay waiting for the fabric to settle and also
changes the behavior of Link Up to break the CRQ to ensure everything
gets cleaned up properly on the VIOS.

Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] lpfc : correct printk types on PPC compiles

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] ipr: fix lockdep warning from ipr_ioa_reset_done

To fix the following lockdep warning we turn the spin_unlock_irq() into
a spin_unlock() and similarly for the corresponding spin_lock_irq(). We
can do this because there is no need to enable interrupts in this path
(thanks to Bring King for the tip).

Badness at kernel/lockdep.c:2193
NIP: c0000000000855d0 LR: c0000000000855b4 CTR: c0000000000482d0
REGS: c00000000fffb8d0 TRAP: 0700   Not tainted  (2.6.28-rc5-autokern1)
MSR: 8000000000021032 <ME,IR,DR>  CR: 28000022  XER: 00000004
TASK = c00000000091fa80[0] 'swapper' THREAD: c000000000a3c000 CPU: 0
GPR00: 0000000000000000 c00000000fffbb50 c000000000a3c2e0 0000000000000001
GPR04: 000000000000a580 c0000000003870d4 0000000000000000 0000000000000001
GPR08: 0000000000000000 c00000000112fdf0 c0000000008ed918 c000000000abcfd0
GPR12: 0000000048000088 c000000000a7f300 0000000000000000 0000000002100000
GPR16: c000000000644bd0 c000000000643390 0000000000000000 00000000003d0c00
GPR20: 00000000028372d8 c0000000007372d8 0000000002837548 c000000000737548
GPR24: c000000000644660 00000000028372d8 000000000000001a c000000076760000
GPR28: 0000000000000004 c0000000004e8450 c0000000009aafb0 c00000000091fa80
NIP [c0000000000855d0] .trace_hardirqs_on_caller+0x10c/0x194
LR [c0000000000855b4] .trace_hardirqs_on_caller+0xf0/0x194
Call Trace:
[c00000000fffbb50] [c00000000fffbbe0] 0xc00000000fffbbe0 (unreliable)
[c00000000fffbbe0] [c0000000004e8450] ._spin_unlock_irq+0x38/0x5c
[c00000000fffbc70] [c0000000003870d4] .ipr_ioa_reset_done+0x204/0x284
[c00000000fffbd10] [c00000000037d234] .ipr_reset_ioa_job+0xc4/0xec
[c00000000fffbda0] [c000000000385ce0] .ipr_isr+0x208/0x484
[c00000000fffbe50] [c0000000000aaf3c] .handle_IRQ_event+0x58/0xd4
[c00000000fffbef0] [c0000000000ad978] .handle_fasteoi_irq+0x110/0x1ac
[c00000000fffbf90] [c000000000025214] .call_handle_irq+0x1c/0x2c
[c000000000a3f9a0] [c00000000000d168] .do_IRQ+0x120/0x210
[c000000000a3fa40] [c000000000004804] hardware_interrupt_entry+0x1c/0x98
--- Exception: 501 at .pseries_dedicated_idle_sleep+0xec/0x1cc
    LR = .pseries_dedicated_idle_sleep+0xdc/0x1cc
[c000000000a3fd30] [c000000000038208] .pseries_dedicated_idle_sleep+0x74/0x1cc (unreliable)
[c000000000a3fdd0] [c000000000012134] .cpu_idle+0x114/0x1dc
[c000000000a3fe60] [c0000000004ecb18] .rest_init+0x7c/0x94
[c000000000a3fee0] [c000000000700a40] .start_kernel+0x4b8/0x4e0
[c000000000a3ff90] [c000000000008368] .start_here_common+0x1c/0x34
Instruction dump:
e92d01b0 80090894 2f800000 41be002c 481ed1d1 60000000 2fa30000 419e0080
e93e8090 80090000 2f800000 409e0070 <0fe00000> 48000068 7fe3fb78 38800001

Signed-off-by: Mark Nelson <markn@au1.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] fc transport: pre-emptively terminate i/o upon dev_loss_tmo timeout

Pre-emptively terminate i/o on the rport if dev_loss_tmo has fired.
The desire is to terminate everything, so that the i/o is cleaned up
prior to the sdev's being unblocked, thus any outstanding timeouts/aborts
are avoided.

Also, we do this early enough such that the rport's port_id field is
still valid. FCOE libFC code needs this info to find the i/o's to
terminate.

Signed-off-by: James Smart <james.smart@emulex.com>
[michaelc@cs.wisc.edu: remove extra scsi_target_unblock call]
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: add support for multi-queue adapter

Following changes have been made.
1. qla_hw_data structure holds an array for request queue pointers,
and an array for response queue pointers.
2. The base request and response queues are created by default.
3. Additional request and response queues are created at the time of vport
creation. If queue resources are exhausted during vport creation, newly
created vports use the default queue.
4. Requests are sent to the request queue that the vport was assigned
in the beginning.
5. Responses are completed on the response queue with which the request queue
is associated with.

[fixup memcpy argument reversal spotted by davej@redhat.com]
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] fcoe: Fibre Channel over Ethernet

Encapsulation protocol for running Fibre Channel over Ethernet interfaces.
Creates virtual Fibre Channel host adapters using libfc.

This layer is the LLD to the scsi-ml. It allocates the Scsi_Host, utilizes
libfc for Fibre Channel protocol processing and interacts with netdev to
send/receive Ethernet packets.

Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] libfc: A modular Fibre Channel library

libFC is composed of 4 blocks supported by an exchange manager
and a framing library. The upper 4 layers are fc_lport, fc_disc,
fc_rport and fc_fcp. A LLD that uses libfc could choose to
either use libfc's block, or using the transport template
defined in libfc.h, override one or more blocks with its own
implementation.

The EM (Exchange Manager) manages exhcanges/sequences for all
commands- ELS, CT and FCP.

The framing library frames ELS and CT commands.

The fc_lport block manages the library's representation of the
host's FC enabled ports.

The fc_disc block manages discovery of targets as well as
handling changes that occur in the FC fabric (via. RSCN events).

The fc_rport block manages the library's representation of other
entities in the FC fabric. Currently the library uses this block
for targets, its peer when in point-to-point mode and the
directory server, but can be extended for other entities if
needed.

The fc_fcp block interacts with the scsi-ml and handles all
I/O.

Signed-off-by: Robert Love <robert.w.love@intel.com>
[jejb: added include of delay.h to fix ppc64 compile prob spotted by sfr]
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] FC protocol definition header files

Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] ibmvscsi: Don't fail EH due to insufficient resources

The ibmvscsi driver currently has a bug in it which can result
in it using up all its event structs for commands. If something
results in all those commands timing out, we won't have any resources
left to send aborts or resets. This results in escalating to a host reset
in order to recover, which is a bit heavy handed. This fixes it
by reducing can_queue by two in order to have resources to do EH.
It also changes the max_requests module parameter so that it is not
writable at runtime, since the code really does not handle it changing
at runtime.

Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] scsi_transport_spi: fix the misuse of scsi_execute return value

[jejb: fix rejections]
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] st: convert st_int_ioctl to use st_scsi_kern_execute

This replaces st_do_scsi in st_int_ioctl with st_scsi_kern_execute.

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Kai Makisara <Kai.Makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] st: convert get_location to use st_scsi_kern_execute

This replaces st_do_scsi in get_location (READ_POSITION) with
st_scsi_kern_execute.

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Kai Makisara <Kai.Makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] st: convert write_mode_page to use st_scsi_kern_execute

This replaces st_do_scsi in write_mode_page (MODE_SELECT) with
st_scsi_kern_execute.

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Kai Makisara <Kai.Makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] st: convert read_mode_page to use st_scsi_kern_execute

This replaces st_do_scsi in read_mode_page (MODE_SENSE) with
st_scsi_kern_execute.

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Kai Makisara <Kai.Makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] st: convert check_tape to use st_scsi_kern_execute

This replaces st_do_scsi in check_tape (READ_BLOCK_LIMITS and
MODE_SENSE) with st_scsi_kern_execute.

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Kai Makisara <Kai.Makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] st: convert st_flush to use st_scsi_kern_execute

This replaces st_do_scsi in st_flush (WRITE FILEMARKS) with
st_scsi_kern_execute.

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Kai Makisara <Kai.Makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] st: convert cross_eof to use st_scsi_kern_execute

This replaces st_do_scsi in cross_eof (SPACE) with
st_scsi_kern_execute.

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Kai Makisara <Kai.Makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] st: convert do_load_unload to use st_scsi_kern_execute

This replaces st_do_scsi in do_load_unload (START STOP) with
st_scsi_kern_execute.

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Kai Makisara <Kai.Makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] st: convert set_location to use st_scsi_kern_execute

This replaces st_do_scsi in set_location (LOCATE 10) with
st_scsi_kern_execute.

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Kai Makisara <Kai.Makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] st: convert test_ready to use st_scsi_kern_execute

This replaces st_do_scsi in test_ready (TEST_UNIT_READY) with
st_scsi_kern_execute.

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Kai Makisara <Kai.Makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] st: add st_scsi_kern_execute helper function

st_scsi_kern_execute is a helper function to perform SCSI commands
synchronously. It supports data transfer with a liner in-kernel buffer
(not scatter gather). st_scsi_kern_execute internally uses
scsi_execute().

The majority of st_do_scsi can be replaced with
st_scsi_kern_execute. This is a preparation for rewriting st_do_scsi
to remove obsolete scsi_execute_async().

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] st: move st_request initialization to st_allocate_request form st_do_scsi

This moves st_request initialization code to st_allocate_request()
form st_do_scsi(). This is a preparation for making
st_allocate_request() usable for everyone, not only st_do_scsi().

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Kai Makisara <Kai.Makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] lpfc 8.3.0 : Update driver version to 8.3.0

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] lpfc 8.3.0 : Hook lpfc's debugfs into Kconfig

Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] lpfc 8.3.0 : Add BlockGuard support (T10-DIF) code

Add SCSI data path, error handling, and debugfs code to complete
BlockGuard support.

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] lpfc 8.3.0 : Add BlockGuard support (T10-DIF) structs and defs

Update struct definitions, #defines, sysfs entries, and initialization
to support BlockGuard.

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] lpfc 8.3.0 : Fix some memory handling issues

- Fix mailbox buffer leak on dump mailbox completion

- Fix mbuf leak in lpfc_pci_probe_one() SLI-2 mode error path

- Don't allocate HBQs in interrupt context

- Use correct size for FCP response buffer so that all available sense
  data is copied

- Fix jiffies calculation to prevent crash when collecting statistical
  data

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] lpfc 8.3.0 : Add active interrupt test for enabling MSI/MSI-X/INTx

Per the recent discussions at the Linux Plumbers Conference, when
enabling MSI or MSI-X, generate a test interrupt to verify the
interrupt routing is working properly.  If the test interrupt fails,
fall back to MSI first, and if that fails as well, to INTx.  If the
interrupt test fails with INTx, log an error and fail the PCI probe.

Also changed the use of spin_(lock|unlock) to the _irq(save|restore)
variants in the interrupt handlers because with multi-message MSI-X,
both interrupt handlers can now run in parallel.

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] lpfc 8.3.0 : Fix several minor issues

- Avoid polling HBA Error Attention when HBA's PCI channel is offline
  due to PCI EEH

- Fix handling of RSCN with non-zero event qualifiers

- Remove unnecessary sleeps during HBA initialization which slow down
  driver load

- Fix internal and external loopback on FCoE HBAs

- Fix incorrect decrement of cmd_pending count in lpfc_queuecomand
  error path

- Fix reporting of port busy events to management application

- Rename lpfc_adjust_queue_depth() to lpfc_rampdown_queue_depth() for
  consistency with its partner lpfc_rampup_queue_depth()

- Delete redundant lpfc_cmd->start_time = jiffies assignment in
  lpfc_queuecommand()

- Fix handling for ELS, mailbox and heartbeat time outs in the worker
  thread by removing unnecessary checking of the work_port_events
  flags.

- Fix NULL pointer dereference in lpfc_prep_els_iocb

- In lpfc_device_recov_npr_node(), move clearing of NLP_NPR_2B_DISC
  flag after call to lpfc_cancel_retry_delay_tmo() to keep
  targets-in-discovery count correct

- Remove lpfc_probe_one()'s call to scsi_scan_host() which could cause
  concurrent SCSI scans to step on each other

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] lpfc 8.3.0 : Fix issue with assumed Interrupt Enable Block support

The phba hbq_get address was setup before the HBA reported support for
Interrupt Enable Block (INB).  This caused loopback tests to fail
after all HBQs had been used once.  Moved setting of hba_get until
after config port mailbox command completes.

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] lpfc 8.3.0 : Added 3 small features and improve PCI EEH support

- Added FC_REG_VPORTRSCN_EVENT to lpfc_nl.h

- Added code to provide option ROM version from HBA and via sysfs

- Added support for HPS bit in config port mailbox command to tell HBA
  that host group pointers are in host memory.

- Bugfix for Extended Error Handling (EEH) support on IBM PowerPC P6
  platform with MSI enabled

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] lpfc 8.3.0 : Fix multiple NPIV issues

- Fix lock up on rmmod with vports defined by having
  lpfc_pci_remove_one() invoke fc_vport_terminate() to remove all the
  vports before invoking fc_remove_host() for the physical port

- Fix echotest failure when NPIV is enabled

- Add the vport_disable function to the physical port's transport
  template to make the vport disable attribute visible

- Set the vport state to DISABLE on create if the disable flag is
  true

- Call lpfc_alloc_sysfs_attr() for vports so that statistical data
  collection works on them

- Support setting a vport's symbolic name via sysfs by writing to
  /sys/class/fc_vport/vportX/symbolic_name

- Fix create vport fails when link is down or in loop mode.  Should be
  able to be create vports any time NPIV is enabled

- Fix slow vport deletes when deleting multiple vports at once

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] lpfc 8.3.0 : Fix system crash due to uninitialized node access

In the IOCB completion handler, always check if the node is valid
before accessing the node object.  Added lpfc_initialize_node() to
initialize nodes.

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] lpfc 8.3.0 : Add kernel-doc headers to lpfc_scsi.c

Add kernel-doc function headers to lpfc_scsi.c

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] lpfc 8.3.0 : Add support for Power Management Suspend/Resume operations

Implement lpfc_pci_suspend_one() and lpfc_pci_resume_one() and
register them in the pci_driver table.

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] lpfc 8.3.0 : Rework RSCN netlink event to send entire RSCN payload

Rework RSCN netlink event to send entire RSCN payload

Also replaces (SCSI_NL_VID_TYPE_PCI | PCI_VENDOR_ID_EMULEX) with
LPFC_NL_VENDOR_ID

Signed-off-by: James Smart <James.Smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] retry with missing data for INQUIRY

This patch changes scsi_probe_lun() to retry INQUIRY if the device has
not actually sent back any INQUIRY data,

This enables the Thecus N2050 storage device to work better. The
firmware on that device starts up strangely; it sends no data in
response to the initial INQUIRY, and it sends the INQUIRY information
in response to the followup REQUEST SENSE. But after that it works
better, so retrying the INQUIRY is enough to get it going.

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] add residual argument to scsi_execute and scsi_execute_req

scsi_execute() and scsi_execute_req() discard the residual length
information. Some callers need it. This adds residual argument
(optional) to scsi_execute and scsi_execute_req.

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] ibmvfc: Fix errors due to inconsistent command data

In order to ensure the VIOS sees a consistent command buffer, we
need to add a memory barrier after building the command buffer
but before sending the command.

Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] ibmvfc: Delay NPIV login retry and add retries

Adds a delay prior to retrying a failed NPIV login. This fixes
a scenario if the backing fibre channel adapter is getting reset
due to an EEH event, NPIV login will fail. Currently, ibmvfc
retries three times very quickly, resets the CRQ and tries one
more time. If the adapter is getting reset due to EEH, this isn't
enough time. This adds a delay prior to retrying a failed NPIV
login and also increments the number of retries.

Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] libiscsi_tcp: support padding offload

cxgb3i does not offload the processing of the header,
but it will always process the padding. This patch
adds a padding offload flag to detect when the LLD
supports this.

The patch also modifies the header processing so that
we do not try to read/bypass the header dugest in the
skb. cxgb3i will not include it with the header like
with other offload cards.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] libiscsi: handle init task failures.

Mgmt setup used to not fail so we did not have to check
the return value. Now with cxgb3i it can so this has us
pass up a error.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] libiscsi: pass opcode into alloc_pdu callout

We do not need to allocate a itt for data_out, so this
passes the opcode to the alloc_pdu callout.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] libiscsi: allow drivers to modify the itt sent to the target

bnx2i and cxgb3i need to encode LLD info in the itt so that
the firmware/hardware can process the pdu. This patch allows
the LLDs to encode info in the task->hdr->itt that they
setup in the alloc_pdu callout (any resources that are allocated
can be freed with the pdu in the cleanup_task callout). If
the LLD encodes info in the itt they should implement a
parse_pdu_itt callout. If parse_pdu_itt is not implemented
libiscsi will do the right thing for the LLD.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] iscsi_tcp: hook iscsi_tcp into new libiscsi_tcp module

This hooks iscsi_tcp into the libiscsi_tcp module and removes
code that is now in libiscsi_tcp.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] iscsi_tcp: split module into lib and lld

As explained in the previous mails, cxgb3i needs iscsi_tcp's
r2t/data_out and data_in procesing so this just moves functions
that both drivers want to use to a new module libiscsi_tcp. The
next patch will hook iscsi_tcp in.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] iscsi_tcp: add iscsi_tcp prefix to iscsi_tcp functions

Add iscsi_tcp prefix to most functions. Some are not changed
becuase they are going to move in the next patch.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] libiscsi: change login data buffer allocation

This modifies the login buffer allocation to use __get_free_pages.
It will allow drivers that want to send this data with zero copy
operations to easily line things up on page boundaries.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] iscsi_tcp: remove unused r2t handling

libiscsi's iscsi_prep_data_out_pdu now handles what
iscsi_tcp's helpers were so we can remove iscsi_tcp's helpers.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] iscsi_tcp: convert to new alloc_hdr api

This converts iscsi_tcp to the new api and modifies how
it handles r2ts.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] iser: convert iser to new alloc_pdu api

This just converts iser to new alloc_pdu api. It still
preallocates the pdu, so there is no difference.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] libiscsi: prepare libiscsi for new offload engines by modifying unsol data code

cxgb3i offloads data transfers. It does not offload the entire scsi/iscsi
procssing like qla4xxx and it does not offload the iscsi sequence
processing like how bnx2i does. cxgb3i relies on iscsi_tcp for the
seqeunce handling so this changes how we transfer unsolicitied data by
adding a common r2t struct and helpers.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] iscsi_tcp: prepare helpers for LLDs that can offload some operations

cxgb3i is unlike qla4xxx and bnx2i in that it does not offload entire
scsi commands or iscsi sequences. Instead it only offloads the transfer
of a ISCSI DATA_IN pdu's data, the digests and padding. This patch fixes up the
iscsi tcp recv path so that it exports its skb recv processing so
cxgb3i and other drivers can call them. All they have to do is pass
the function the skb with the hdr or data pdu header and this function
will do the rest.

Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] remove timeout from struct scsi_device

by removing the unused timeout parameter we ensure a compile failure if
anyone is accidentally still using it rather than the block timeout.

Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] st: update to use block timeout

Since we're trying to eliminate struct scsi_device timeout, the tape
driver has to be updated to use the block queue timeout instead.  The
tape use of scsi_device timeout looks to be self consistent, so I don't
think this necessarily fixes any bug, but it has to be done to allow me
to remove the timeout parameter from struct scsi_device.

Acked-by: Kai Makisara <Kai.Makisara@kolumbus.fi>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] mac_esp: fix for quadras with two esp chips

On the Quadra 900 and 950 there are two ESP chips sharing one IRQ. Because
the shared IRQ is edge-triggered, we must make sure that an IRQ transition
from one chip doesn't go unnoticed when the shared IRQ is already active
due to the other. This patch prevents interrupts getting lost so that both
SCSI busses may be used simultaneously.

Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] m68k: mac_esp asm fix

Fix asm constraints and arguments so as not to transfer an odd byte when
there may be more words to transfer. The bug would probably also cause
exceptions sometimes by transferring one too many bytes.

Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Code changes for vport bus reset

The following patch changes the handling of bus reset when issued from a
vport. In the bus reset code, an extra check is made to make sure that the lip
reset is not done before resetting the targets if the bus reset came from a
vport.

Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] simplify scsi_io_completion()

This patch (as1142b) consolidates a lot of repetitious code in
scsi_io_completion().  It also fixes a few comments.  Most
importantly, however, it clearly distinguishes among the three sorts
of retries that can be done when a command fails to complete:

Unprepare the request and resubmit it, so that a new
command will be created for it.

Requeue the request directly so that it will be retried
immediately using the same command.

Requeue the request so that it will be retried following
a short delay.

Complete the remainder of the request with an I/O error.

[jejb: Updates
     1. For several error conditions, we would now print the sense twice
        in slightly different ways, so unify the location of sense
        printing.
     2. I added more descriptions to actual failure conditions for
        better debugging
     3. according to spec, ABORTED_COMMAND is supposed to be retried
        (except on DIF failure).  Our old behaviour of erroring it looks
        to be a bug.
     4. I'd prefer not to default initialise the action variable because
        that ensures that every leg of the error handler has an
        associated action and the compiler will warn if someone later
        accidentally misses one or removes one.
]
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] ibmvfc: Driver version 1.0.4

Bump driver version

Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] ibmvfc: Handle port login required response

The virtual fibre channel stack can return a failure response for a command
indicating the port login has been invalidated without sending the client
an async event. Add code to handle this response and initiate a PLOGI.

Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] ibmvfc: Fix command timeouts due to cached CRQ access

The CRQs used by the ibmvfc driver are read and written by both
the client and the server. Therefore, we need to mark them volatile
so that we do not cache their contents when handling an interrupt.
This fixes a problem which can surface as occasional command timeouts.
No commands were actually timing out, but due to accessing cached data
for the CRQ in the interrupt handler, the interrupt was not processing
all command completions as it should.

Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] ibmvfc: Fix oops in interrupt handler

Fixes an oops that can occur in the interrupt handler
if we get a lot of async events.

Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] scsi_dh_rdac: Add LSI vendor and product ids in rdac device list

[jejb: fixed whitespace damage]
Signed-off-by: Babu Moger <Babu.Moger@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] fusion: use ARRAY_SIZE

ARRAY_SIZE is more concise to use when the size of an array is divided by
the size of its type or the size of its first element.

Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: "Prakash, Sathya" <Sathya.Prakash@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] fusion: remove excess kernel-doc notation

Remove excess kernel-doc function parameter notation:

Warning(drivers/message/fusion/mptbase.c:964): Excess function parameter or struct member 'handle' description in 'mpt_free_msg_frame'
Warning(drivers/message/fusion/mptbase.c:5434): Excess function parameter or struct member 'portnum' description in 'mpt_findImVolumes'
Warning(drivers/message/fusion/mptbase.c:6949): Excess function parameter or struct member 'mr' description in 'mpt_spi_log_info'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
cc: Eric.Moore@lsi.com
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Fix for build warning

drivers/scsi/qla2xxx/qla_os.c: In function 'qla2x00_probe_one':
drivers/scsi/qla2xxx/qla_os.c:1582: warning: 'mem_only' is used uninitialized in this function

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Code changes for qla data structure refactoring

Following changes have been made:

1. Outstanding commands are based on a request queue, scsi_qla_host
   does not maintain it anymore.

2. start_scsi is accessed via isp_ops struct instead of direct
   invocation.

3. Interrupt registrations are done using response queue instead of
   device id.

Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] qla2xxx: Refactor qla data structures

Following changes have been made to the qla2xxx FC driver in
preparation for the multi- queue and future SR IOV hardware.

1. scsi_qla_host structure has been changed to contain scsi host
   specific data only.

2. A new structure, qla_hw_data is created to contain HBA specific
   hardware data.

3. Request and response IO specific data strucures are created.

4. The global list of fcports for the hba is not maintained anymore,
   instead a fcport list is construted on per scsi_qla_host.

Signed-of-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] scsi_error: TASK ABORTED status handling improvement

This patch improves handling of TASK ABORTED status by Linux SCSI
mid-layer. Currently, command returned with this status considered
failed and returned to upper layers. It leads to additional error
recovery load on file systems and block layer, which sometimes can
cause undesired side effects, like I/O errors and file systems
corruptions. See http://lkml.org/lkml/2008/11/1/38, for instance.

From other side, TASK ABORTED status is returned by SCSI target if the
corresponding command was aborted by another initiator and the target
has TAS bit set in the control mode page. So, in the majority of cases
commands with TASK ABORTED status should be simply retried. In other
cases, maybe_retry path will not retry if no retries are allowed.

This patch implement suggestion by James Bottomley from
http://marc.info/?l=linux-scsi&m=121932916906009&w=2.

Signed-off-by: Vladislav Bolkhovitin <vst@vlnb.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] scsi_dh: Retry mode select in rdac device handler

When the mode select sent to the controller fails with the retryable
error, it is better to retry the mode_select from the hardware handler
itself, instead of propagating the failure to dm-multipath.

Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] scsi_dh: Make sure the state of a path is set properly when controller is swapped from passive to active

When the controller ownership is changed (from passive to active),
check_ownership() doesn't set the state of the device to ACTIVE.

Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Reported-by: "Moger, Babu" <Babu.Moger@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] scsi_error: fix indentation and braces disagreement - add braces

...and the list of recent breakage goes on and on, this time
it's 242f9dcb8ba6f (block: unify request timeout handling)
which broke it.

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] tmscsim: fix indentation and braces disagreement - add braces

Lucky winner is 557cc476c04 ([SCSI] tmscsim: Fixup
KERN_INFO in printk).

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] u14-34f: fix scsi_dma_map failure case

When unsigned, scsi_dma_map may return -ENOMEM without triggering BUG_ON()

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] esp_scsi: Use DIV_ROUND_UP

Use the macro DIV_ROUND_UP and eliminate the variable rounded_up, as
suggested by Matthew Wilcox.

Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: David Miller <davem@davemloft.net>
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] ibmvfc: Driver version 1.0.3

Bump driver version.

Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] ibmvfc: Quiet gcc warning in ibmvfc_reset_device

Stops gcc from complaining about a possible uninitialized
variable being used in ibmvfc_reset_device.

Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] ibmvfc: Fix target initialization failure retry handling

If the ibmvfc driver is in discovery attempting to log into a target
and it encounters an error, the command may get retried one or more
times, depending on the error received. If the retries are
unsuccessful such that the discovery thread gives up on discovery to
that target, the target ends up in a state where, if SCSI core had
previously known about the device, the host will get unblocked but the
host will not be logged into the target, causing any commands sent to
the target to fail. This patch fixes this so that if this occurs, the
target is deleted such that the normal dev_loss processing can occur
instead.

Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] ibmvfc: Error handling fixes

Due to an ambiguity in the VIOS VFC interface specification,
abort/cancel handling is not done correctly and can result in double
completion of commands. In order to cancel all outstanding commands to
a device, a cancel must be sent, followed by an abort task set. After
the responses are received for these commands, there may still be
commands outstanding, in the process of getting flushed back, in which
case, we need to wait for them. This patch removes the assumption that
if the abort and the cancel both complete successfully that the device
queue has been flushed and waits for all the responses to come back.

Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] ibmvfc: Fix error reporting for some FC errors

If either a "transport fault" or a "general transport" error is received
and no other error information is available, the command is improperly
returned as successful. Fix this to return DID_ERROR in this case.

Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] ibmvfc: Fix log level filtering

The ibmvfc log level filtering logic was reversed. The log_level scsi
host parameter should result in more verbose logs when log_level is
larger, not smaller.

Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] Clean up my email address and use a single standard address for everything

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] aacraid: check pci_alloc_consistent errors

We need to check the address that pci_alloc_consistent() returns since
it might fail.

When pci_alloc_consistent() fails, some IOMMUs set the dma_handle
argument to zero. So we can't use fibptr->hw_fib_pa directly here.

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Aacraid List <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] advansys, arcmsr, ipr, nsp32, qla1280, stex: use pci_ioremap_bar()

Use the newly introduced pci_ioremap_bar() function in drivers/scsi.
pci_ioremap_bar() just takes a pci device and a bar number, with the goal
of making it really hard to get wrong, while also having a central place
to stick sanity checks.

Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Matthew Wilcox <willy@linux.intel.com>
Cc: Brian King <brking@us.ibm.com>
Cc: Ed Lin <ed.lin@promise.com>
Cc: Nick Cheng <nick.cheng@areca.com.tw>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] scsi ioctl: fix kernel-doc warning

Fix kernel-doc parameter warning and correct the function name:

Warning(linux-next-20081022//drivers/scsi/scsi_ioctl.c:281): No description found for parameter 'ndelay'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>