sky2: put PHY in sleep when down
authorStephen Hemminger <shemminger@vyatta.com>
Thu, 15 May 2008 00:04:16 +0000 (17:04 -0700)
committerJeff Garzik <jgarzik@redhat.com>
Sat, 31 May 2008 02:19:16 +0000 (22:19 -0400)
Put PHY int sleep mode (from vendor sk98lin 10.50 driver) when the
network device is brought down.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
drivers/net/sky2.c
drivers/net/sky2.h

index ad35674..59cb9cd 100644 (file)
@@ -641,11 +641,47 @@ static void sky2_phy_power_up(struct sky2_hw *hw, unsigned port)
 static void sky2_phy_power_down(struct sky2_hw *hw, unsigned port)
 {
        u32 reg1;
+       u16 ctrl;
+
+       /* release GPHY Control reset */
+       sky2_write8(hw, SK_REG(port, GPHY_CTRL), GPC_RST_CLR);
+
+       /* release GMAC reset */
+       sky2_write8(hw, SK_REG(port, GMAC_CTRL), GMC_RST_CLR);
+
+       if (hw->flags & SKY2_HW_NEWER_PHY) {
+               /* select page 2 to access MAC control register */
+               gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 2);
+
+               ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL);
+               /* allow GMII Power Down */
+               ctrl &= ~PHY_M_MAC_GMIF_PUP;
+               gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl);
+
+               /* set page register back to 0 */
+               gm_phy_write(hw, port, PHY_MARV_EXT_ADR, 0);
+       }
+
+       /* setup General Purpose Control Register */
+       gma_write16(hw, port, GM_GP_CTRL,
+                   GM_GPCR_FL_PASS | GM_GPCR_SPEED_100 | GM_GPCR_AU_ALL_DIS);
+
+       if (hw->chip_id != CHIP_ID_YUKON_EC) {
+               if (hw->chip_id == CHIP_ID_YUKON_EC_U) {
+                       ctrl = gm_phy_read(hw, port, PHY_MARV_PHY_CTRL);
+
+                       /* enable Power Down */
+                       ctrl |= PHY_M_PC_POW_D_ENA;
+                       gm_phy_write(hw, port, PHY_MARV_PHY_CTRL, ctrl);
+               }
+
+               /* set IEEE compatible Power Down Mode (dev. #4.99) */
+               gm_phy_write(hw, port, PHY_MARV_CTRL, PHY_CT_PDOWN);
+       }
 
        sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
        reg1 = sky2_pci_read32(hw, PCI_DEV_REG1);
-       reg1 |= phy_power[port];
-
+       reg1 |= phy_power[port];                /* set PHY to PowerDown/COMA Mode */
        sky2_pci_write32(hw, PCI_DEV_REG1, reg1);
        sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
 }
index c0a5eea..d63106c 100644 (file)
@@ -1143,6 +1143,12 @@ enum {
        PHY_M_PC_ENA_AUTO       = 3, /* 11 = Enable Automatic Crossover */
 };
 
+/* for Yukon-EC Ultra Gigabit Ethernet PHY (88E1149 only) */
+enum {
+       PHY_M_PC_COP_TX_DIS     = 1<<3, /* Copper Transmitter Disable */
+       PHY_M_PC_POW_D_ENA      = 1<<2, /* Power Down Enable */
+};
+
 /* for 10/100 Fast Ethernet PHY (88E3082 only) */
 enum {
        PHY_M_PC_ENA_DTE_DT     = 1<<15, /* Enable Data Terminal Equ. (DTE) Detect */
@@ -1411,6 +1417,7 @@ enum {
 /*****  PHY_MARV_PHY_CTRL (page 2)             16 bit r/w      MAC Specific Ctrl *****/
 enum {
        PHY_M_MAC_MD_MSK        = 7<<7, /* Bit  9.. 7: Mode Select Mask */
+       PHY_M_MAC_GMIF_PUP      = 1<<3, /* GMII Power Up (88E1149 only) */
        PHY_M_MAC_MD_AUTO       = 3,/* Auto Copper/1000Base-X */
        PHY_M_MAC_MD_COPPER     = 5,/* Copper only */
        PHY_M_MAC_MD_1000BX     = 7,/* 1000Base-X only */