#include <linux/usb/r8a66597.h>
-#define SYSCFG0 0x00
-#define SYSCFG1 0x02
-#define SYSSTS0 0x04
-#define SYSSTS1 0x06
-#define DVSTCTR0 0x08
-#define DVSTCTR1 0x0A
-#define TESTMODE 0x0C
-#define PINCFG 0x0E
-#define DMA0CFG 0x10
-#define DMA1CFG 0x12
-#define CFIFO 0x14
-#define D0FIFO 0x18
-#define D1FIFO 0x1C
-#define CFIFOSEL 0x20
-#define CFIFOCTR 0x22
-#define CFIFOSIE 0x24
-#define D0FIFOSEL 0x28
-#define D0FIFOCTR 0x2A
-#define D1FIFOSEL 0x2C
-#define D1FIFOCTR 0x2E
-#define INTENB0 0x30
-#define INTENB1 0x32
-#define INTENB2 0x34
-#define BRDYENB 0x36
-#define NRDYENB 0x38
-#define BEMPENB 0x3A
-#define SOFCFG 0x3C
-#define INTSTS0 0x40
-#define INTSTS1 0x42
-#define INTSTS2 0x44
-#define BRDYSTS 0x46
-#define NRDYSTS 0x48
-#define BEMPSTS 0x4A
-#define FRMNUM 0x4C
-#define UFRMNUM 0x4E
-#define USBADDR 0x50
-#define USBREQ 0x54
-#define USBVAL 0x56
-#define USBINDX 0x58
-#define USBLENG 0x5A
-#define DCPCFG 0x5C
-#define DCPMAXP 0x5E
-#define DCPCTR 0x60
-#define PIPESEL 0x64
-#define PIPECFG 0x68
-#define PIPEBUF 0x6A
-#define PIPEMAXP 0x6C
-#define PIPEPERI 0x6E
-#define PIPE1CTR 0x70
-#define PIPE2CTR 0x72
-#define PIPE3CTR 0x74
-#define PIPE4CTR 0x76
-#define PIPE5CTR 0x78
-#define PIPE6CTR 0x7A
-#define PIPE7CTR 0x7C
-#define PIPE8CTR 0x7E
-#define PIPE9CTR 0x80
-#define PIPE1TRE 0x90
-#define PIPE1TRN 0x92
-#define PIPE2TRE 0x94
-#define PIPE2TRN 0x96
-#define PIPE3TRE 0x98
-#define PIPE3TRN 0x9A
-#define PIPE4TRE 0x9C
-#define PIPE4TRN 0x9E
-#define PIPE5TRE 0xA0
-#define PIPE5TRN 0xA2
-#define DEVADD0 0xD0
-#define DEVADD1 0xD2
-#define DEVADD2 0xD4
-#define DEVADD3 0xD6
-#define DEVADD4 0xD8
-#define DEVADD5 0xDA
-#define DEVADD6 0xDC
-#define DEVADD7 0xDE
-#define DEVADD8 0xE0
-#define DEVADD9 0xE2
-#define DEVADDA 0xE4
-
-/* System Configuration Control Register */
-#define XTAL 0xC000 /* b15-14: Crystal selection */
-#define XTAL48 0x8000 /* 48MHz */
-#define XTAL24 0x4000 /* 24MHz */
-#define XTAL12 0x0000 /* 12MHz */
-#define XCKE 0x2000 /* b13: External clock enable */
-#define PLLC 0x0800 /* b11: PLL control */
-#define SCKE 0x0400 /* b10: USB clock enable */
-#define PCSDIS 0x0200 /* b9: not CS wakeup */
-#define LPSME 0x0100 /* b8: Low power sleep mode */
-#define HSE 0x0080 /* b7: Hi-speed enable */
-#define DCFM 0x0040 /* b6: Controller function select */
-#define DRPD 0x0020 /* b5: D+/- pull down control */
-#define DPRPU 0x0010 /* b4: D+ pull up control */
-#define USBE 0x0001 /* b0: USB module operation enable */
-
-/* System Configuration Status Register */
-#define OVCBIT 0x8000 /* b15-14: Over-current bit */
-#define OVCMON 0xC000 /* b15-14: Over-current monitor */
-#define SOFEA 0x0020 /* b5: SOF monitor */
-#define IDMON 0x0004 /* b3: ID-pin monitor */
-#define LNST 0x0003 /* b1-0: D+, D- line status */
-#define SE1 0x0003 /* SE1 */
-#define FS_KSTS 0x0002 /* Full-Speed K State */
-#define FS_JSTS 0x0001 /* Full-Speed J State */
-#define LS_JSTS 0x0002 /* Low-Speed J State */
-#define LS_KSTS 0x0001 /* Low-Speed K State */
-#define SE0 0x0000 /* SE0 */
-
-/* Device State Control Register */
-#define EXTLP0 0x0400 /* b10: External port */
-#define VBOUT 0x0200 /* b9: VBUS output */
-#define WKUP 0x0100 /* b8: Remote wakeup */
-#define RWUPE 0x0080 /* b7: Remote wakeup sense */
-#define USBRST 0x0040 /* b6: USB reset enable */
-#define RESUME 0x0020 /* b5: Resume enable */
-#define UACT 0x0010 /* b4: USB bus enable */
-#define RHST 0x0007 /* b1-0: Reset handshake status */
-#define HSPROC 0x0004 /* HS handshake is processing */
-#define HSMODE 0x0003 /* Hi-Speed mode */
-#define FSMODE 0x0002 /* Full-Speed mode */
-#define LSMODE 0x0001 /* Low-Speed mode */
-#define UNDECID 0x0000 /* Undecided */
-
-/* Test Mode Register */
-#define UTST 0x000F /* b3-0: Test select */
-#define H_TST_PACKET 0x000C /* HOST TEST Packet */
-#define H_TST_SE0_NAK 0x000B /* HOST TEST SE0 NAK */
-#define H_TST_K 0x000A /* HOST TEST K */
-#define H_TST_J 0x0009 /* HOST TEST J */
-#define H_TST_NORMAL 0x0000 /* HOST Normal Mode */
-#define P_TST_PACKET 0x0004 /* PERI TEST Packet */
-#define P_TST_SE0_NAK 0x0003 /* PERI TEST SE0 NAK */
-#define P_TST_K 0x0002 /* PERI TEST K */
-#define P_TST_J 0x0001 /* PERI TEST J */
-#define P_TST_NORMAL 0x0000 /* PERI Normal Mode */
-
-/* Data Pin Configuration Register */
-#define LDRV 0x8000 /* b15: Drive Current Adjust */
-#define VIF1 0x0000 /* VIF = 1.8V */
-#define VIF3 0x8000 /* VIF = 3.3V */
-#define INTA 0x0001 /* b1: USB INT-pin active */
-
-/* DMAx Pin Configuration Register */
-#define DREQA 0x4000 /* b14: Dreq active select */
-#define BURST 0x2000 /* b13: Burst mode */
-#define DACKA 0x0400 /* b10: Dack active select */
-#define DFORM 0x0380 /* b9-7: DMA mode select */
-#define CPU_ADR_RD_WR 0x0000 /* Address + RD/WR mode (CPU bus) */
-#define CPU_DACK_RD_WR 0x0100 /* DACK + RD/WR mode (CPU bus) */
-#define CPU_DACK_ONLY 0x0180 /* DACK only mode (CPU bus) */
-#define SPLIT_DACK_ONLY 0x0200 /* DACK only mode (SPLIT bus) */
-#define DENDA 0x0040 /* b6: Dend active select */
-#define PKTM 0x0020 /* b5: Packet mode */
-#define DENDE 0x0010 /* b4: Dend enable */
-#define OBUS 0x0004 /* b2: OUTbus mode */
-
-/* CFIFO/DxFIFO Port Select Register */
-#define RCNT 0x8000 /* b15: Read count mode */
-#define REW 0x4000 /* b14: Buffer rewind */
-#define DCLRM 0x2000 /* b13: DMA buffer clear mode */
-#define DREQE 0x1000 /* b12: DREQ output enable */
-#define MBW_8 0x0000 /* 8bit */
-#define MBW_16 0x0400 /* 16bit */
-#define MBW_32 0x0800 /* 32bit */
-#define BIGEND 0x0100 /* b8: Big endian mode */
-#define BYTE_LITTLE 0x0000 /* little dendian */
-#define BYTE_BIG 0x0100 /* big endifan */
-#define ISEL 0x0020 /* b5: DCP FIFO port direction select */
-#define CURPIPE 0x000F /* b2-0: PIPE select */
-
-/* CFIFO/DxFIFO Port Control Register */
-#define BVAL 0x8000 /* b15: Buffer valid flag */
-#define BCLR 0x4000 /* b14: Buffer clear */
-#define FRDY 0x2000 /* b13: FIFO ready */
-#define DTLN 0x0FFF /* b11-0: FIFO received data length */
-
-/* Interrupt Enable Register 0 */
-#define VBSE 0x8000 /* b15: VBUS interrupt */
-#define RSME 0x4000 /* b14: Resume interrupt */
-#define SOFE 0x2000 /* b13: Frame update interrupt */
-#define DVSE 0x1000 /* b12: Device state transition interrupt */
-#define CTRE 0x0800 /* b11: Control transfer stage transition interrupt */
-#define BEMPE 0x0400 /* b10: Buffer empty interrupt */
-#define NRDYE 0x0200 /* b9: Buffer not ready interrupt */
-#define BRDYE 0x0100 /* b8: Buffer ready interrupt */
-
-/* Interrupt Enable Register 1 */
-#define OVRCRE 0x8000 /* b15: Over-current interrupt */
-#define BCHGE 0x4000 /* b14: USB us chenge interrupt */
-#define DTCHE 0x1000 /* b12: Detach sense interrupt */
-#define ATTCHE 0x0800 /* b11: Attach sense interrupt */
-#define EOFERRE 0x0040 /* b6: EOF error interrupt */
-#define SIGNE 0x0020 /* b5: SETUP IGNORE interrupt */
-#define SACKE 0x0010 /* b4: SETUP ACK interrupt */
-
-/* BRDY Interrupt Enable/Status Register */
-#define BRDY9 0x0200 /* b9: PIPE9 */
-#define BRDY8 0x0100 /* b8: PIPE8 */
-#define BRDY7 0x0080 /* b7: PIPE7 */
-#define BRDY6 0x0040 /* b6: PIPE6 */
-#define BRDY5 0x0020 /* b5: PIPE5 */
-#define BRDY4 0x0010 /* b4: PIPE4 */
-#define BRDY3 0x0008 /* b3: PIPE3 */
-#define BRDY2 0x0004 /* b2: PIPE2 */
-#define BRDY1 0x0002 /* b1: PIPE1 */
-#define BRDY0 0x0001 /* b1: PIPE0 */
-
-/* NRDY Interrupt Enable/Status Register */
-#define NRDY9 0x0200 /* b9: PIPE9 */
-#define NRDY8 0x0100 /* b8: PIPE8 */
-#define NRDY7 0x0080 /* b7: PIPE7 */
-#define NRDY6 0x0040 /* b6: PIPE6 */
-#define NRDY5 0x0020 /* b5: PIPE5 */
-#define NRDY4 0x0010 /* b4: PIPE4 */
-#define NRDY3 0x0008 /* b3: PIPE3 */
-#define NRDY2 0x0004 /* b2: PIPE2 */
-#define NRDY1 0x0002 /* b1: PIPE1 */
-#define NRDY0 0x0001 /* b1: PIPE0 */
-
-/* BEMP Interrupt Enable/Status Register */
-#define BEMP9 0x0200 /* b9: PIPE9 */
-#define BEMP8 0x0100 /* b8: PIPE8 */
-#define BEMP7 0x0080 /* b7: PIPE7 */
-#define BEMP6 0x0040 /* b6: PIPE6 */
-#define BEMP5 0x0020 /* b5: PIPE5 */
-#define BEMP4 0x0010 /* b4: PIPE4 */
-#define BEMP3 0x0008 /* b3: PIPE3 */
-#define BEMP2 0x0004 /* b2: PIPE2 */
-#define BEMP1 0x0002 /* b1: PIPE1 */
-#define BEMP0 0x0001 /* b0: PIPE0 */
-
-/* SOF Pin Configuration Register */
-#define TRNENSEL 0x0100 /* b8: Select transaction enable period */
-#define BRDYM 0x0040 /* b6: BRDY clear timing */
-#define INTL 0x0020 /* b5: Interrupt sense select */
-#define EDGESTS 0x0010 /* b4: */
-#define SOFMODE 0x000C /* b3-2: SOF pin select */
-#define SOF_125US 0x0008 /* SOF OUT 125us Frame Signal */
-#define SOF_1MS 0x0004 /* SOF OUT 1ms Frame Signal */
-#define SOF_DISABLE 0x0000 /* SOF OUT Disable */
-
-/* Interrupt Status Register 0 */
-#define VBINT 0x8000 /* b15: VBUS interrupt */
-#define RESM 0x4000 /* b14: Resume interrupt */
-#define SOFR 0x2000 /* b13: SOF frame update interrupt */
-#define DVST 0x1000 /* b12: Device state transition interrupt */
-#define CTRT 0x0800 /* b11: Control transfer stage transition interrupt */
-#define BEMP 0x0400 /* b10: Buffer empty interrupt */
-#define NRDY 0x0200 /* b9: Buffer not ready interrupt */
-#define BRDY 0x0100 /* b8: Buffer ready interrupt */
-#define VBSTS 0x0080 /* b7: VBUS input port */
-#define DVSQ 0x0070 /* b6-4: Device state */
-#define DS_SPD_CNFG 0x0070 /* Suspend Configured */
-#define DS_SPD_ADDR 0x0060 /* Suspend Address */
-#define DS_SPD_DFLT 0x0050 /* Suspend Default */
-#define DS_SPD_POWR 0x0040 /* Suspend Powered */
-#define DS_SUSP 0x0040 /* Suspend */
-#define DS_CNFG 0x0030 /* Configured */
-#define DS_ADDS 0x0020 /* Address */
-#define DS_DFLT 0x0010 /* Default */
-#define DS_POWR 0x0000 /* Powered */
-#define DVSQS 0x0030 /* b5-4: Device state */
-#define VALID 0x0008 /* b3: Setup packet detected flag */
-#define CTSQ 0x0007 /* b2-0: Control transfer stage */
-#define CS_SQER 0x0006 /* Sequence error */
-#define CS_WRND 0x0005 /* Control write nodata status stage */
-#define CS_WRSS 0x0004 /* Control write status stage */
-#define CS_WRDS 0x0003 /* Control write data stage */
-#define CS_RDSS 0x0002 /* Control read status stage */
-#define CS_RDDS 0x0001 /* Control read data stage */
-#define CS_IDST 0x0000 /* Idle or setup stage */
-
-/* Interrupt Status Register 1 */
-#define OVRCR 0x8000 /* b15: Over-current interrupt */
-#define BCHG 0x4000 /* b14: USB bus chenge interrupt */
-#define DTCH 0x1000 /* b12: Detach sense interrupt */
-#define ATTCH 0x0800 /* b11: Attach sense interrupt */
-#define EOFERR 0x0040 /* b6: EOF-error interrupt */
-#define SIGN 0x0020 /* b5: Setup ignore interrupt */
-#define SACK 0x0010 /* b4: Setup acknowledge interrupt */
-
-/* Frame Number Register */
-#define OVRN 0x8000 /* b15: Overrun error */
-#define CRCE 0x4000 /* b14: Received data error */
-#define FRNM 0x07FF /* b10-0: Frame number */
-
-/* Micro Frame Number Register */
-#define UFRNM 0x0007 /* b2-0: Micro frame number */
-
-/* Default Control Pipe Maxpacket Size Register */
-/* Pipe Maxpacket Size Register */
-#define DEVSEL 0xF000 /* b15-14: Device address select */
-#define MAXP 0x007F /* b6-0: Maxpacket size of default control pipe */
-
-/* Default Control Pipe Control Register */
-#define BSTS 0x8000 /* b15: Buffer status */
-#define SUREQ 0x4000 /* b14: Send USB request */
-#define CSCLR 0x2000 /* b13: complete-split status clear */
-#define CSSTS 0x1000 /* b12: complete-split status */
-#define SUREQCLR 0x0800 /* b11: stop setup request */
-#define SQCLR 0x0100 /* b8: Sequence toggle bit clear */
-#define SQSET 0x0080 /* b7: Sequence toggle bit set */
-#define SQMON 0x0040 /* b6: Sequence toggle bit monitor */
-#define PBUSY 0x0020 /* b5: pipe busy */
-#define PINGE 0x0010 /* b4: ping enable */
-#define CCPL 0x0004 /* b2: Enable control transfer complete */
-#define PID 0x0003 /* b1-0: Response PID */
-#define PID_STALL11 0x0003 /* STALL */
-#define PID_STALL 0x0002 /* STALL */
-#define PID_BUF 0x0001 /* BUF */
-#define PID_NAK 0x0000 /* NAK */
-
-/* Pipe Window Select Register */
-#define PIPENM 0x0007 /* b2-0: Pipe select */
-
-/* Pipe Configuration Register */
-#define R8A66597_TYP 0xC000 /* b15-14: Transfer type */
-#define R8A66597_ISO 0xC000 /* Isochronous */
-#define R8A66597_INT 0x8000 /* Interrupt */
-#define R8A66597_BULK 0x4000 /* Bulk */
-#define R8A66597_BFRE 0x0400 /* b10: Buffer ready interrupt mode select */
-#define R8A66597_DBLB 0x0200 /* b9: Double buffer mode select */
-#define R8A66597_CNTMD 0x0100 /* b8: Continuous transfer mode select */
-#define R8A66597_SHTNAK 0x0080 /* b7: Transfer end NAK */
-#define R8A66597_DIR 0x0010 /* b4: Transfer direction select */
-#define R8A66597_EPNUM 0x000F /* b3-0: Eendpoint number select */
-
-/* Pipe Buffer Configuration Register */
-#define BUFSIZE 0x7C00 /* b14-10: Pipe buffer size */
-#define BUFNMB 0x007F /* b6-0: Pipe buffer number */
-#define PIPE0BUF 256
-#define PIPExBUF 64
-
-/* Pipe Maxpacket Size Register */
-#define MXPS 0x07FF /* b10-0: Maxpacket size */
-
-/* Pipe Cycle Configuration Register */
-#define IFIS 0x1000 /* b12: Isochronous in-buffer flush mode select */
-#define IITV 0x0007 /* b2-0: Isochronous interval */
-
-/* Pipex Control Register */
-#define BSTS 0x8000 /* b15: Buffer status */
-#define INBUFM 0x4000 /* b14: IN buffer monitor (Only for PIPE1 to 5) */
-#define CSCLR 0x2000 /* b13: complete-split status clear */
-#define CSSTS 0x1000 /* b12: complete-split status */
-#define ATREPM 0x0400 /* b10: Auto repeat mode */
-#define ACLRM 0x0200 /* b9: Out buffer auto clear mode */
-#define SQCLR 0x0100 /* b8: Sequence toggle bit clear */
-#define SQSET 0x0080 /* b7: Sequence toggle bit set */
-#define SQMON 0x0040 /* b6: Sequence toggle bit monitor */
-#define PBUSY 0x0020 /* b5: pipe busy */
-#define PID 0x0003 /* b1-0: Response PID */
-
-/* PIPExTRE */
-#define TRENB 0x0200 /* b9: Transaction counter enable */
-#define TRCLR 0x0100 /* b8: Transaction counter clear */
-
-/* PIPExTRN */
-#define TRNCNT 0xFFFF /* b15-0: Transaction counter */
-
-/* DEVADDx */
-#define UPPHUB 0x7800
-#define HUBPORT 0x0700
-#define USBSPD 0x00C0
-#define RTPORT 0x0001
-
#define R8A66597_MAX_NUM_PIPE 10
#define R8A66597_BUF_BSIZE 8
#define R8A66597_MAX_DEVICE 10
#define R8A66597_PLATDATA_XTAL_48MHZ 0x03
struct r8a66597_platdata {
- /* This ops can controll port power instead of DVSTCTR register. */
+ /* This callback can control port power instead of DVSTCTR register. */
void (*port_power)(int port, int power);
/* set one = on chip controller, set zero = external controller */
/* set one = big endian, set zero = little endian */
unsigned endian:1;
};
-#endif
+
+/* Register definitions */
+#define SYSCFG0 0x00
+#define SYSCFG1 0x02
+#define SYSSTS0 0x04
+#define SYSSTS1 0x06
+#define DVSTCTR0 0x08
+#define DVSTCTR1 0x0A
+#define TESTMODE 0x0C
+#define PINCFG 0x0E
+#define DMA0CFG 0x10
+#define DMA1CFG 0x12
+#define CFIFO 0x14
+#define D0FIFO 0x18
+#define D1FIFO 0x1C
+#define CFIFOSEL 0x20
+#define CFIFOCTR 0x22
+#define CFIFOSIE 0x24
+#define D0FIFOSEL 0x28
+#define D0FIFOCTR 0x2A
+#define D1FIFOSEL 0x2C
+#define D1FIFOCTR 0x2E
+#define INTENB0 0x30
+#define INTENB1 0x32
+#define INTENB2 0x34
+#define BRDYENB 0x36
+#define NRDYENB 0x38
+#define BEMPENB 0x3A
+#define SOFCFG 0x3C
+#define INTSTS0 0x40
+#define INTSTS1 0x42
+#define INTSTS2 0x44
+#define BRDYSTS 0x46
+#define NRDYSTS 0x48
+#define BEMPSTS 0x4A
+#define FRMNUM 0x4C
+#define UFRMNUM 0x4E
+#define USBADDR 0x50
+#define USBREQ 0x54
+#define USBVAL 0x56
+#define USBINDX 0x58
+#define USBLENG 0x5A
+#define DCPCFG 0x5C
+#define DCPMAXP 0x5E
+#define DCPCTR 0x60
+#define PIPESEL 0x64
+#define PIPECFG 0x68
+#define PIPEBUF 0x6A
+#define PIPEMAXP 0x6C
+#define PIPEPERI 0x6E
+#define PIPE1CTR 0x70
+#define PIPE2CTR 0x72
+#define PIPE3CTR 0x74
+#define PIPE4CTR 0x76
+#define PIPE5CTR 0x78
+#define PIPE6CTR 0x7A
+#define PIPE7CTR 0x7C
+#define PIPE8CTR 0x7E
+#define PIPE9CTR 0x80
+#define PIPE1TRE 0x90
+#define PIPE1TRN 0x92
+#define PIPE2TRE 0x94
+#define PIPE2TRN 0x96
+#define PIPE3TRE 0x98
+#define PIPE3TRN 0x9A
+#define PIPE4TRE 0x9C
+#define PIPE4TRN 0x9E
+#define PIPE5TRE 0xA0
+#define PIPE5TRN 0xA2
+#define DEVADD0 0xD0
+#define DEVADD1 0xD2
+#define DEVADD2 0xD4
+#define DEVADD3 0xD6
+#define DEVADD4 0xD8
+#define DEVADD5 0xDA
+#define DEVADD6 0xDC
+#define DEVADD7 0xDE
+#define DEVADD8 0xE0
+#define DEVADD9 0xE2
+#define DEVADDA 0xE4
+
+/* System Configuration Control Register */
+#define XTAL 0xC000 /* b15-14: Crystal selection */
+#define XTAL48 0x8000 /* 48MHz */
+#define XTAL24 0x4000 /* 24MHz */
+#define XTAL12 0x0000 /* 12MHz */
+#define XCKE 0x2000 /* b13: External clock enable */
+#define PLLC 0x0800 /* b11: PLL control */
+#define SCKE 0x0400 /* b10: USB clock enable */
+#define PCSDIS 0x0200 /* b9: not CS wakeup */
+#define LPSME 0x0100 /* b8: Low power sleep mode */
+#define HSE 0x0080 /* b7: Hi-speed enable */
+#define DCFM 0x0040 /* b6: Controller function select */
+#define DRPD 0x0020 /* b5: D+/- pull down control */
+#define DPRPU 0x0010 /* b4: D+ pull up control */
+#define USBE 0x0001 /* b0: USB module operation enable */
+
+/* System Configuration Status Register */
+#define OVCBIT 0x8000 /* b15-14: Over-current bit */
+#define OVCMON 0xC000 /* b15-14: Over-current monitor */
+#define SOFEA 0x0020 /* b5: SOF monitor */
+#define IDMON 0x0004 /* b3: ID-pin monitor */
+#define LNST 0x0003 /* b1-0: D+, D- line status */
+#define SE1 0x0003 /* SE1 */
+#define FS_KSTS 0x0002 /* Full-Speed K State */
+#define FS_JSTS 0x0001 /* Full-Speed J State */
+#define LS_JSTS 0x0002 /* Low-Speed J State */
+#define LS_KSTS 0x0001 /* Low-Speed K State */
+#define SE0 0x0000 /* SE0 */
+
+/* Device State Control Register */
+#define EXTLP0 0x0400 /* b10: External port */
+#define VBOUT 0x0200 /* b9: VBUS output */
+#define WKUP 0x0100 /* b8: Remote wakeup */
+#define RWUPE 0x0080 /* b7: Remote wakeup sense */
+#define USBRST 0x0040 /* b6: USB reset enable */
+#define RESUME 0x0020 /* b5: Resume enable */
+#define UACT 0x0010 /* b4: USB bus enable */
+#define RHST 0x0007 /* b1-0: Reset handshake status */
+#define HSPROC 0x0004 /* HS handshake is processing */
+#define HSMODE 0x0003 /* Hi-Speed mode */
+#define FSMODE 0x0002 /* Full-Speed mode */
+#define LSMODE 0x0001 /* Low-Speed mode */
+#define UNDECID 0x0000 /* Undecided */
+
+/* Test Mode Register */
+#define UTST 0x000F /* b3-0: Test select */
+#define H_TST_PACKET 0x000C /* HOST TEST Packet */
+#define H_TST_SE0_NAK 0x000B /* HOST TEST SE0 NAK */
+#define H_TST_K 0x000A /* HOST TEST K */
+#define H_TST_J 0x0009 /* HOST TEST J */
+#define H_TST_NORMAL 0x0000 /* HOST Normal Mode */
+#define P_TST_PACKET 0x0004 /* PERI TEST Packet */
+#define P_TST_SE0_NAK 0x0003 /* PERI TEST SE0 NAK */
+#define P_TST_K 0x0002 /* PERI TEST K */
+#define P_TST_J 0x0001 /* PERI TEST J */
+#define P_TST_NORMAL 0x0000 /* PERI Normal Mode */
+
+/* Data Pin Configuration Register */
+#define LDRV 0x8000 /* b15: Drive Current Adjust */
+#define VIF1 0x0000 /* VIF = 1.8V */
+#define VIF3 0x8000 /* VIF = 3.3V */
+#define INTA 0x0001 /* b1: USB INT-pin active */
+
+/* DMAx Pin Configuration Register */
+#define DREQA 0x4000 /* b14: Dreq active select */
+#define BURST 0x2000 /* b13: Burst mode */
+#define DACKA 0x0400 /* b10: Dack active select */
+#define DFORM 0x0380 /* b9-7: DMA mode select */
+#define CPU_ADR_RD_WR 0x0000 /* Address + RD/WR mode (CPU bus) */
+#define CPU_DACK_RD_WR 0x0100 /* DACK + RD/WR mode (CPU bus) */
+#define CPU_DACK_ONLY 0x0180 /* DACK only mode (CPU bus) */
+#define SPLIT_DACK_ONLY 0x0200 /* DACK only mode (SPLIT bus) */
+#define DENDA 0x0040 /* b6: Dend active select */
+#define PKTM 0x0020 /* b5: Packet mode */
+#define DENDE 0x0010 /* b4: Dend enable */
+#define OBUS 0x0004 /* b2: OUTbus mode */
+
+/* CFIFO/DxFIFO Port Select Register */
+#define RCNT 0x8000 /* b15: Read count mode */
+#define REW 0x4000 /* b14: Buffer rewind */
+#define DCLRM 0x2000 /* b13: DMA buffer clear mode */
+#define DREQE 0x1000 /* b12: DREQ output enable */
+#define MBW_8 0x0000 /* 8bit */
+#define MBW_16 0x0400 /* 16bit */
+#define MBW_32 0x0800 /* 32bit */
+#define BIGEND 0x0100 /* b8: Big endian mode */
+#define BYTE_LITTLE 0x0000 /* little dendian */
+#define BYTE_BIG 0x0100 /* big endifan */
+#define ISEL 0x0020 /* b5: DCP FIFO port direction select */
+#define CURPIPE 0x000F /* b2-0: PIPE select */
+
+/* CFIFO/DxFIFO Port Control Register */
+#define BVAL 0x8000 /* b15: Buffer valid flag */
+#define BCLR 0x4000 /* b14: Buffer clear */
+#define FRDY 0x2000 /* b13: FIFO ready */
+#define DTLN 0x0FFF /* b11-0: FIFO received data length */
+
+/* Interrupt Enable Register 0 */
+#define VBSE 0x8000 /* b15: VBUS interrupt */
+#define RSME 0x4000 /* b14: Resume interrupt */
+#define SOFE 0x2000 /* b13: Frame update interrupt */
+#define DVSE 0x1000 /* b12: Device state transition interrupt */
+#define CTRE 0x0800 /* b11: Control transfer stage transition interrupt */
+#define BEMPE 0x0400 /* b10: Buffer empty interrupt */
+#define NRDYE 0x0200 /* b9: Buffer not ready interrupt */
+#define BRDYE 0x0100 /* b8: Buffer ready interrupt */
+
+/* Interrupt Enable Register 1 */
+#define OVRCRE 0x8000 /* b15: Over-current interrupt */
+#define BCHGE 0x4000 /* b14: USB us chenge interrupt */
+#define DTCHE 0x1000 /* b12: Detach sense interrupt */
+#define ATTCHE 0x0800 /* b11: Attach sense interrupt */
+#define EOFERRE 0x0040 /* b6: EOF error interrupt */
+#define SIGNE 0x0020 /* b5: SETUP IGNORE interrupt */
+#define SACKE 0x0010 /* b4: SETUP ACK interrupt */
+
+/* BRDY Interrupt Enable/Status Register */
+#define BRDY9 0x0200 /* b9: PIPE9 */
+#define BRDY8 0x0100 /* b8: PIPE8 */
+#define BRDY7 0x0080 /* b7: PIPE7 */
+#define BRDY6 0x0040 /* b6: PIPE6 */
+#define BRDY5 0x0020 /* b5: PIPE5 */
+#define BRDY4 0x0010 /* b4: PIPE4 */
+#define BRDY3 0x0008 /* b3: PIPE3 */
+#define BRDY2 0x0004 /* b2: PIPE2 */
+#define BRDY1 0x0002 /* b1: PIPE1 */
+#define BRDY0 0x0001 /* b1: PIPE0 */
+
+/* NRDY Interrupt Enable/Status Register */
+#define NRDY9 0x0200 /* b9: PIPE9 */
+#define NRDY8 0x0100 /* b8: PIPE8 */
+#define NRDY7 0x0080 /* b7: PIPE7 */
+#define NRDY6 0x0040 /* b6: PIPE6 */
+#define NRDY5 0x0020 /* b5: PIPE5 */
+#define NRDY4 0x0010 /* b4: PIPE4 */
+#define NRDY3 0x0008 /* b3: PIPE3 */
+#define NRDY2 0x0004 /* b2: PIPE2 */
+#define NRDY1 0x0002 /* b1: PIPE1 */
+#define NRDY0 0x0001 /* b1: PIPE0 */
+
+/* BEMP Interrupt Enable/Status Register */
+#define BEMP9 0x0200 /* b9: PIPE9 */
+#define BEMP8 0x0100 /* b8: PIPE8 */
+#define BEMP7 0x0080 /* b7: PIPE7 */
+#define BEMP6 0x0040 /* b6: PIPE6 */
+#define BEMP5 0x0020 /* b5: PIPE5 */
+#define BEMP4 0x0010 /* b4: PIPE4 */
+#define BEMP3 0x0008 /* b3: PIPE3 */
+#define BEMP2 0x0004 /* b2: PIPE2 */
+#define BEMP1 0x0002 /* b1: PIPE1 */
+#define BEMP0 0x0001 /* b0: PIPE0 */
+
+/* SOF Pin Configuration Register */
+#define TRNENSEL 0x0100 /* b8: Select transaction enable period */
+#define BRDYM 0x0040 /* b6: BRDY clear timing */
+#define INTL 0x0020 /* b5: Interrupt sense select */
+#define EDGESTS 0x0010 /* b4: */
+#define SOFMODE 0x000C /* b3-2: SOF pin select */
+#define SOF_125US 0x0008 /* SOF OUT 125us Frame Signal */
+#define SOF_1MS 0x0004 /* SOF OUT 1ms Frame Signal */
+#define SOF_DISABLE 0x0000 /* SOF OUT Disable */
+
+/* Interrupt Status Register 0 */
+#define VBINT 0x8000 /* b15: VBUS interrupt */
+#define RESM 0x4000 /* b14: Resume interrupt */
+#define SOFR 0x2000 /* b13: SOF frame update interrupt */
+#define DVST 0x1000 /* b12: Device state transition interrupt */
+#define CTRT 0x0800 /* b11: Control transfer stage transition interrupt */
+#define BEMP 0x0400 /* b10: Buffer empty interrupt */
+#define NRDY 0x0200 /* b9: Buffer not ready interrupt */
+#define BRDY 0x0100 /* b8: Buffer ready interrupt */
+#define VBSTS 0x0080 /* b7: VBUS input port */
+#define DVSQ 0x0070 /* b6-4: Device state */
+#define DS_SPD_CNFG 0x0070 /* Suspend Configured */
+#define DS_SPD_ADDR 0x0060 /* Suspend Address */
+#define DS_SPD_DFLT 0x0050 /* Suspend Default */
+#define DS_SPD_POWR 0x0040 /* Suspend Powered */
+#define DS_SUSP 0x0040 /* Suspend */
+#define DS_CNFG 0x0030 /* Configured */
+#define DS_ADDS 0x0020 /* Address */
+#define DS_DFLT 0x0010 /* Default */
+#define DS_POWR 0x0000 /* Powered */
+#define DVSQS 0x0030 /* b5-4: Device state */
+#define VALID 0x0008 /* b3: Setup packet detected flag */
+#define CTSQ 0x0007 /* b2-0: Control transfer stage */
+#define CS_SQER 0x0006 /* Sequence error */
+#define CS_WRND 0x0005 /* Control write nodata status stage */
+#define CS_WRSS 0x0004 /* Control write status stage */
+#define CS_WRDS 0x0003 /* Control write data stage */
+#define CS_RDSS 0x0002 /* Control read status stage */
+#define CS_RDDS 0x0001 /* Control read data stage */
+#define CS_IDST 0x0000 /* Idle or setup stage */
+
+/* Interrupt Status Register 1 */
+#define OVRCR 0x8000 /* b15: Over-current interrupt */
+#define BCHG 0x4000 /* b14: USB bus chenge interrupt */
+#define DTCH 0x1000 /* b12: Detach sense interrupt */
+#define ATTCH 0x0800 /* b11: Attach sense interrupt */
+#define EOFERR 0x0040 /* b6: EOF-error interrupt */
+#define SIGN 0x0020 /* b5: Setup ignore interrupt */
+#define SACK 0x0010 /* b4: Setup acknowledge interrupt */
+
+/* Frame Number Register */
+#define OVRN 0x8000 /* b15: Overrun error */
+#define CRCE 0x4000 /* b14: Received data error */
+#define FRNM 0x07FF /* b10-0: Frame number */
+
+/* Micro Frame Number Register */
+#define UFRNM 0x0007 /* b2-0: Micro frame number */
+
+/* Default Control Pipe Maxpacket Size Register */
+/* Pipe Maxpacket Size Register */
+#define DEVSEL 0xF000 /* b15-14: Device address select */
+#define MAXP 0x007F /* b6-0: Maxpacket size of default control pipe */
+
+/* Default Control Pipe Control Register */
+#define BSTS 0x8000 /* b15: Buffer status */
+#define SUREQ 0x4000 /* b14: Send USB request */
+#define CSCLR 0x2000 /* b13: complete-split status clear */
+#define CSSTS 0x1000 /* b12: complete-split status */
+#define SUREQCLR 0x0800 /* b11: stop setup request */
+#define SQCLR 0x0100 /* b8: Sequence toggle bit clear */
+#define SQSET 0x0080 /* b7: Sequence toggle bit set */
+#define SQMON 0x0040 /* b6: Sequence toggle bit monitor */
+#define PBUSY 0x0020 /* b5: pipe busy */
+#define PINGE 0x0010 /* b4: ping enable */
+#define CCPL 0x0004 /* b2: Enable control transfer complete */
+#define PID 0x0003 /* b1-0: Response PID */
+#define PID_STALL11 0x0003 /* STALL */
+#define PID_STALL 0x0002 /* STALL */
+#define PID_BUF 0x0001 /* BUF */
+#define PID_NAK 0x0000 /* NAK */
+
+/* Pipe Window Select Register */
+#define PIPENM 0x0007 /* b2-0: Pipe select */
+
+/* Pipe Configuration Register */
+#define R8A66597_TYP 0xC000 /* b15-14: Transfer type */
+#define R8A66597_ISO 0xC000 /* Isochronous */
+#define R8A66597_INT 0x8000 /* Interrupt */
+#define R8A66597_BULK 0x4000 /* Bulk */
+#define R8A66597_BFRE 0x0400 /* b10: Buffer ready interrupt mode select */
+#define R8A66597_DBLB 0x0200 /* b9: Double buffer mode select */
+#define R8A66597_CNTMD 0x0100 /* b8: Continuous transfer mode select */
+#define R8A66597_SHTNAK 0x0080 /* b7: Transfer end NAK */
+#define R8A66597_DIR 0x0010 /* b4: Transfer direction select */
+#define R8A66597_EPNUM 0x000F /* b3-0: Eendpoint number select */
+
+/* Pipe Buffer Configuration Register */
+#define BUFSIZE 0x7C00 /* b14-10: Pipe buffer size */
+#define BUFNMB 0x007F /* b6-0: Pipe buffer number */
+#define PIPE0BUF 256
+#define PIPExBUF 64
+
+/* Pipe Maxpacket Size Register */
+#define MXPS 0x07FF /* b10-0: Maxpacket size */
+
+/* Pipe Cycle Configuration Register */
+#define IFIS 0x1000 /* b12: Isochronous in-buffer flush mode select */
+#define IITV 0x0007 /* b2-0: Isochronous interval */
+
+/* Pipex Control Register */
+#define BSTS 0x8000 /* b15: Buffer status */
+#define INBUFM 0x4000 /* b14: IN buffer monitor (Only for PIPE1 to 5) */
+#define CSCLR 0x2000 /* b13: complete-split status clear */
+#define CSSTS 0x1000 /* b12: complete-split status */
+#define ATREPM 0x0400 /* b10: Auto repeat mode */
+#define ACLRM 0x0200 /* b9: Out buffer auto clear mode */
+#define SQCLR 0x0100 /* b8: Sequence toggle bit clear */
+#define SQSET 0x0080 /* b7: Sequence toggle bit set */
+#define SQMON 0x0040 /* b6: Sequence toggle bit monitor */
+#define PBUSY 0x0020 /* b5: pipe busy */
+#define PID 0x0003 /* b1-0: Response PID */
+
+/* PIPExTRE */
+#define TRENB 0x0200 /* b9: Transaction counter enable */
+#define TRCLR 0x0100 /* b8: Transaction counter clear */
+
+/* PIPExTRN */
+#define TRNCNT 0xFFFF /* b15-0: Transaction counter */
+
+/* DEVADDx */
+#define UPPHUB 0x7800
+#define HUBPORT 0x0700
+#define USBSPD 0x00C0
+#define RTPORT 0x0001
+
+#endif /* __LINUX_USB_R8A66597_H */
git://ftp.safe.ca / safe / jmp / linux-2.6 / commitdiff