Various libata documentation updates.

This is a merger of libata docs + cleanups from
Martin Waitz <tali@admingilde.org> and me.

From: Randy Dunlap <rdunlap@xenotime.net>
From: Martin Waitz <tali@admingilde.org>

Fix libata kernel-doc comments to match code.
Add some function parameters to kernel-doc.
Fix some typos/spellos.
Put comments in <= 80 columns.
Make one DPRINTK string unique.
Fix sparse cast warnings.

Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>

diff --git a/drivers/scsi/ata_piix.c b/drivers/scsi/ata_piix.c
index 2d984b0..49cc420 100644 (file)
--- a/drivers/scsi/ata_piix.c
+++ b/drivers/scsi/ata_piix.c
@@ -630,6 +630,7 @@ static int piix_disable_ahci(struct pci_dev *pdev)
 
 /**
  *     piix_check_450nx_errata -       Check for problem 450NX setup
+ *     @ata_dev: the PCI device to check
  *     
  *     Check for the present of 450NX errata #19 and errata #25. If
  *     they are found return an error code so we can turn off DMA

diff --git a/drivers/scsi/libata-core.c b/drivers/scsi/libata-core.c
index b369dbd..249e67f 100644 (file)
--- a/drivers/scsi/libata-core.c
+++ b/drivers/scsi/libata-core.c
@@ -1442,12 +1442,11 @@ static inline u8 ata_dev_knobble(const struct ata_port *ap)
 }
 
 /**
- *     ata_dev_config - Run device specific handlers and check for
- *                      SATA->PATA bridges
- *     @ap: Bus
- *     @i:  Device
+ * ata_dev_config - Run device specific handlers & check for SATA->PATA bridges
+ * @ap: Bus
+ * @i:  Device
  *
- *     LOCKING:
+ * LOCKING:
  */
 
 void ata_dev_config(struct ata_port *ap, unsigned int i)
@@ -1794,9 +1793,9 @@ int ata_timing_compute(struct ata_device *adev, unsigned short speed,
        ata_timing_quantize(t, t, T, UT);
 
        /*
-        * Even in DMA/UDMA modes we still use PIO access for IDENTIFY, S.M.A.R.T
-        * and some other commands. We have to ensure that the DMA cycle timing is
-        * slower/equal than the fastest PIO timing.
+        * Even in DMA/UDMA modes we still use PIO access for IDENTIFY,
+        * S.M.A.R.T * and some other commands. We have to ensure that the
+        * DMA cycle timing is slower/equal than the fastest PIO timing.
         */
 
        if (speed > XFER_PIO_4) {
@@ -1805,7 +1804,7 @@ int ata_timing_compute(struct ata_device *adev, unsigned short speed,
        }
 
        /*
-        * Lenghten active & recovery time so that cycle time is correct.
+        * Lengthen active & recovery time so that cycle time is correct.
         */
 
        if (t->act8b + t->rec8b < t->cyc8b) {
@@ -1924,7 +1923,6 @@ static void ata_host_set_dma(struct ata_port *ap, u8 xfer_mode,
  *
  *     LOCKING:
  *     PCI/etc. bus probe sem.
- *
  */
 static void ata_set_mode(struct ata_port *ap)
 {
@@ -1973,7 +1971,6 @@ err_out:
  *     or a timeout occurs.
  *
  *     LOCKING: None.
- *
  */
 
 unsigned int ata_busy_sleep (struct ata_port *ap,
@@ -3200,7 +3197,7 @@ void ata_poll_qc_complete(struct ata_queued_cmd *qc)
 }
 
 /**
- *     ata_pio_poll -
+ *     ata_pio_poll - poll using PIO, depending on current state
  *     @ap: the target ata_port
  *
  *     LOCKING:
@@ -3307,7 +3304,7 @@ static int ata_pio_complete (struct ata_port *ap)
 
 
 /**
- *     swap_buf_le16 - swap halves of 16-words in place
+ *     swap_buf_le16 - swap halves of 16-bit words in place
  *     @buf:  Buffer to swap
  *     @buf_words:  Number of 16-bit words in buffer.
  *
@@ -4520,19 +4517,6 @@ err_out:
 }
 
 
-/**
- *     ata_port_start - Set port up for dma.
- *     @ap: Port to initialize
- *
- *     Called just after data structures for each port are
- *     initialized.  Allocates space for PRD table.
- *
- *     May be used as the port_start() entry in ata_port_operations.
- *
- *     LOCKING:
- *     Inherited from caller.
- */
-
 /*
  * Execute a 'simple' command, that only consists of the opcode 'cmd' itself,
  * without filling any other registers
@@ -4584,6 +4568,8 @@ static int ata_start_drive(struct ata_port *ap, struct ata_device *dev)
 
 /**
  *     ata_device_resume - wakeup a previously suspended devices
+ *     @ap: port the device is connected to
+ *     @dev: the device to resume
  *
  *     Kick the drive back into action, by sending it an idle immediate
  *     command and making sure its transfer mode matches between drive
@@ -4606,10 +4592,11 @@ int ata_device_resume(struct ata_port *ap, struct ata_device *dev)
 
 /**
  *     ata_device_suspend - prepare a device for suspend
+ *     @ap: port the device is connected to
+ *     @dev: the device to suspend
  *
  *     Flush the cache on the drive, if appropriate, then issue a
  *     standbynow command.
- *
  */
 int ata_device_suspend(struct ata_port *ap, struct ata_device *dev)
 {
@@ -4623,6 +4610,19 @@ int ata_device_suspend(struct ata_port *ap, struct ata_device *dev)
        return 0;
 }
 
+/**
+ *     ata_port_start - Set port up for dma.
+ *     @ap: Port to initialize
+ *
+ *     Called just after data structures for each port are
+ *     initialized.  Allocates space for PRD table.
+ *
+ *     May be used as the port_start() entry in ata_port_operations.
+ *
+ *     LOCKING:
+ *     Inherited from caller.
+ */
+
 int ata_port_start (struct ata_port *ap)
 {
        struct device *dev = ap->host_set->dev;
@@ -4880,9 +4880,9 @@ int ata_device_add(const struct ata_probe_ent *ent)
 
                ap = host_set->ports[i];
 
-               DPRINTK("ata%u: probe begin\n", ap->id);
+               DPRINTK("ata%u: bus probe begin\n", ap->id);
                rc = ata_bus_probe(ap);
-               DPRINTK("ata%u: probe end\n", ap->id);
+               DPRINTK("ata%u: bus probe end\n", ap->id);
 
                if (rc) {
                        /* FIXME: do something useful here?
@@ -4906,7 +4906,7 @@ int ata_device_add(const struct ata_probe_ent *ent)
        }
 
        /* probes are done, now scan each port's disk(s) */
-       DPRINTK("probe begin\n");
+       DPRINTK("host probe begin\n");
        for (i = 0; i < count; i++) {
                struct ata_port *ap = host_set->ports[i];
 

diff --git a/drivers/scsi/libata-scsi.c b/drivers/scsi/libata-scsi.c
index ab6b533..6df8293 100644 (file)
--- a/drivers/scsi/libata-scsi.c
+++ b/drivers/scsi/libata-scsi.c
@@ -151,7 +151,7 @@ int ata_cmd_ioctl(struct scsi_device *scsidev, void __user *arg)
        struct scsi_sense_hdr sshdr;
        enum dma_data_direction data_dir;
 
-       if (NULL == (void *)arg)
+       if (arg == NULL)
                return -EINVAL;
 
        if (copy_from_user(args, arg, sizeof(args)))
@@ -201,7 +201,7 @@ int ata_cmd_ioctl(struct scsi_device *scsidev, void __user *arg)
        /* Need code to retrieve data from check condition? */
 
        if ((argbuf)
-        && copy_to_user((void *)(arg + sizeof(args)), argbuf, argsize))
+        && copy_to_user(arg + sizeof(args), argbuf, argsize))
                rc = -EFAULT;
 error:
        if (argbuf)
@@ -228,7 +228,7 @@ int ata_task_ioctl(struct scsi_device *scsidev, void __user *arg)
        u8 args[7];
        struct scsi_sense_hdr sshdr;
 
-       if (NULL == (void *)arg)
+       if (arg == NULL)
                return -EINVAL;
 
        if (copy_from_user(args, arg, sizeof(args)))
@@ -2533,7 +2533,8 @@ out_unlock:
 
 /**
  *     ata_scsi_simulate - simulate SCSI command on ATA device
- *     @id: current IDENTIFY data for target device.
+ *     @ap: port the device is connected to
+ *     @dev: the target device
  *     @cmd: SCSI command being sent to device.
  *     @done: SCSI command completion function.
  *