[PATCH] skge: handle pci errors better

When a PCI error occurs, try and report more info.

Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

diff --git a/drivers/net/skge.c b/drivers/net/skge.c
index 7f8e8dd..0325fbc 100644 (file)
--- a/drivers/net/skge.c
+++ b/drivers/net/skge.c
@@ -2764,17 +2764,6 @@ static void skge_mac_parity(struct skge_hw *hw, int port)
                            ? GMF_CLI_TX_FC : GMF_CLI_TX_PE);
 }
 
-static void skge_pci_clear(struct skge_hw *hw)
-{
-       u16 status;
-
-       pci_read_config_word(hw->pdev, PCI_STATUS, &status);
-       skge_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
-       pci_write_config_word(hw->pdev, PCI_STATUS,
-                             status | PCI_STATUS_ERROR_BITS);
-       skge_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
-}
-
 static void skge_mac_intr(struct skge_hw *hw, int port)
 {
        if (hw->chip_id == CHIP_ID_GENESIS)
@@ -2816,23 +2805,39 @@ static void skge_error_irq(struct skge_hw *hw)
        if (hwstatus & IS_M2_PAR_ERR)
                skge_mac_parity(hw, 1);
 
-       if (hwstatus & IS_R1_PAR_ERR)
+       if (hwstatus & IS_R1_PAR_ERR) {
+               printk(KERN_ERR PFX "%s: receive queue parity error\n",
+                      hw->dev[0]->name);
                skge_write32(hw, B0_R1_CSR, CSR_IRQ_CL_P);
+       }
 
-       if (hwstatus & IS_R2_PAR_ERR)
+       if (hwstatus & IS_R2_PAR_ERR) {
+               printk(KERN_ERR PFX "%s: receive queue parity error\n",
+                      hw->dev[1]->name);
                skge_write32(hw, B0_R2_CSR, CSR_IRQ_CL_P);
+       }
 
        if (hwstatus & (IS_IRQ_MST_ERR|IS_IRQ_STAT)) {
-               printk(KERN_ERR PFX "hardware error detected (status 0x%x)\n",
-                      hwstatus);
+               u16 pci_status, pci_cmd;
+
+               pci_read_config_word(hw->pdev, PCI_COMMAND, &pci_cmd);
+               pci_read_config_word(hw->pdev, PCI_STATUS, &pci_status);
 
-               skge_pci_clear(hw);
+               printk(KERN_ERR PFX "%s: PCI error cmd=%#x status=%#x\n",
+                              pci_name(hw->pdev), pci_cmd, pci_status);
+
+               /* Write the error bits back to clear them. */
+               pci_status &= PCI_STATUS_ERROR_BITS;
+               skge_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
+               pci_write_config_word(hw->pdev, PCI_COMMAND,
+                                     pci_cmd | PCI_COMMAND_SERR | PCI_COMMAND_PARITY);
+               pci_write_config_word(hw->pdev, PCI_STATUS, pci_status);
+               skge_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
 
                /* if error still set then just ignore it */
                hwstatus = skge_read32(hw, B0_HWE_ISRC);
                if (hwstatus & IS_IRQ_STAT) {
-                       pr_debug("IRQ status %x: still set ignoring hardware errors\n",
-                              hwstatus);
+                       printk(KERN_INFO PFX "unable to clear error (so ignoring them)\n");
                        hw->intr_mask &= ~IS_HW_ERR;
                }
        }
@@ -2998,7 +3003,7 @@ static const char *skge_board_name(const struct skge_hw *hw)
 static int skge_reset(struct skge_hw *hw)
 {
        u32 reg;
-       u16 ctst;
+       u16 ctst, pci_status;
        u8 t8, mac_cfg, pmd_type, phy_type;
        int i;
 
@@ -3009,8 +3014,13 @@ static int skge_reset(struct skge_hw *hw)
        skge_write8(hw, B0_CTST, CS_RST_CLR);
 
        /* clear PCI errors, if any */
-       skge_pci_clear(hw);
+       skge_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_ON);
+       skge_write8(hw, B2_TST_CTRL2, 0);
 
+       pci_read_config_word(hw->pdev, PCI_STATUS, &pci_status);
+       pci_write_config_word(hw->pdev, PCI_STATUS,
+                             pci_status | PCI_STATUS_ERROR_BITS);
+       skge_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF);
        skge_write8(hw, B0_CTST, CS_MRST_CLR);
 
        /* restore CLK_RUN bits (for Yukon-Lite) */
@@ -3377,7 +3387,6 @@ static void __devexit skge_remove(struct pci_dev *pdev)
 
        skge_write32(hw, B0_IMSK, 0);
        skge_write16(hw, B0_LED, LED_STAT_OFF);
-       skge_pci_clear(hw);
        skge_write8(hw, B0_CTST, CS_RST_SET);
 
        tasklet_kill(&hw->ext_tasklet);