sh: Fix up cf-enabler dependency for SE boards.

This was using CONFIG_SH_SOLUTION_ENGINE, where we really wanted
CONFIG_SOLUTION_ENGINE. While we're at it, move the whole CF
enabler mess somewhere better suited.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>

diff --git a/arch/sh/Kconfig b/arch/sh/Kconfig
index b16407c..924efe5 100644 (file)
--- a/arch/sh/Kconfig
+++ b/arch/sh/Kconfig
@@ -404,50 +404,6 @@ source "arch/sh/boards/renesas/hs7751rvoip/Kconfig"
 source "arch/sh/boards/renesas/rts7751r2d/Kconfig"
 source "arch/sh/boards/renesas/r7780rp/Kconfig"
 
-config CF_ENABLER
-       bool "Compact Flash Enabler support"
-       depends on SH_SOLUTION_ENGINE || SH_SH03
-       ---help---
-         Compact Flash is a small, removable mass storage device introduced
-         in 1994 originally as a PCMCIA device.  If you say `Y' here, you
-         compile in support for Compact Flash devices directly connected to
-         a SuperH processor.  A Compact Flash FAQ is available at
-         <http://www.compactflash.org/faqs/faq.htm>.
-
-         If your board has "Directly Connected" CompactFlash at area 5 or 6,
-         you may want to enable this option.  Then, you can use CF as
-         primary IDE drive (only tested for SanDisk).
-
-         If in doubt, select 'N'.
-
-choice
-       prompt "Compact Flash Connection Area"
-       depends on CF_ENABLER
-       default CF_AREA6
-
-config CF_AREA5
-       bool "Area5"
-       help
-         If your board has "Directly Connected" CompactFlash, You should
-         select the area where your CF is connected to.
-
-         - "Area5" if CompactFlash is connected to Area 5 (0x14000000)
-         - "Area6" if it is connected to Area 6 (0x18000000)
-
-         "Area6" will work for most boards.
-
-config CF_AREA6
-       bool "Area6"
-
-endchoice
-
-config CF_BASE_ADDR
-       hex
-       depends on CF_ENABLER
-       default "0xb8000000" if CF_AREA6
-       default "0xb4000000" if CF_AREA5
-
-
 menu "Timer and clock configuration"
 
 config SH_TMU
@@ -705,6 +661,49 @@ config SUPERHYWAY
        tristate "SuperHyway Bus support"
        depends on CPU_SUBTYPE_SH4_202
 
+config CF_ENABLER
+       bool "Compact Flash Enabler support"
+       depends on SOLUTION_ENGINE || SH_SH03
+       ---help---
+         Compact Flash is a small, removable mass storage device introduced
+         in 1994 originally as a PCMCIA device.  If you say `Y' here, you
+         compile in support for Compact Flash devices directly connected to
+         a SuperH processor.  A Compact Flash FAQ is available at
+         <http://www.compactflash.org/faqs/faq.htm>.
+
+         If your board has "Directly Connected" CompactFlash at area 5 or 6,
+         you may want to enable this option.  Then, you can use CF as
+         primary IDE drive (only tested for SanDisk).
+
+         If in doubt, select 'N'.
+
+choice
+       prompt "Compact Flash Connection Area"
+       depends on CF_ENABLER
+       default CF_AREA6
+
+config CF_AREA5
+       bool "Area5"
+       help
+         If your board has "Directly Connected" CompactFlash, You should
+         select the area where your CF is connected to.
+
+         - "Area5" if CompactFlash is connected to Area 5 (0x14000000)
+         - "Area6" if it is connected to Area 6 (0x18000000)
+
+         "Area6" will work for most boards.
+
+config CF_AREA6
+       bool "Area6"
+
+endchoice
+
+config CF_BASE_ADDR
+       hex
+       depends on CF_ENABLER
+       default "0xb8000000" if CF_AREA6
+       default "0xb4000000" if CF_AREA5
+
 source "arch/sh/drivers/pci/Kconfig"
 
 source "drivers/pci/Kconfig"