#define USB_MCFG_RDCOMB (1<<30)
#define USB_MCFG_SSDEN (1<<23)
#define USB_MCFG_PHYPLLEN (1<<19)
+#define USB_MCFG_UCECLKEN (1<<18)
#define USB_MCFG_EHCCLKEN (1<<17)
+#ifdef CONFIG_DMA_COHERENT
#define USB_MCFG_UCAM (1<<7)
+#else
+#define USB_MCFG_UCAM (0)
+#endif
#define USB_MCFG_EBMEN (1<<3)
#define USB_MCFG_EMEMEN (1<<2)
-#define USBH_ENABLE_CE (USB_MCFG_PHYPLLEN | USB_MCFG_EHCCLKEN)
+#define USBH_ENABLE_CE (USB_MCFG_PHYPLLEN | USB_MCFG_EHCCLKEN)
+#define USBH_ENABLE_INIT (USB_MCFG_PFEN | USB_MCFG_RDCOMB | \
+ USBH_ENABLE_CE | USB_MCFG_SSDEN | \
+ USB_MCFG_UCAM | USB_MCFG_EBMEN | \
+ USB_MCFG_EMEMEN)
-#ifdef CONFIG_DMA_COHERENT
-#define USBH_ENABLE_INIT (USBH_ENABLE_CE \
- | USB_MCFG_PFEN | USB_MCFG_RDCOMB \
- | USB_MCFG_SSDEN | USB_MCFG_UCAM \
- | USB_MCFG_EBMEN | USB_MCFG_EMEMEN)
-#else
-#define USBH_ENABLE_INIT (USBH_ENABLE_CE \
- | USB_MCFG_PFEN | USB_MCFG_RDCOMB \
- | USB_MCFG_SSDEN \
- | USB_MCFG_EBMEN | USB_MCFG_EMEMEN)
-#endif
#define USBH_DISABLE (USB_MCFG_EBMEN | USB_MCFG_EMEMEN)
extern int usb_disabled(void);
-/*-------------------------------------------------------------------------*/
-
-static void au1xxx_start_ehc(struct platform_device *dev)
+static void au1xxx_start_ehc(void)
{
- pr_debug(__FILE__ ": starting Au1xxx EHCI USB Controller\n");
-
- /* write HW defaults again in case Yamon cleared them */
- if (au_readl(USB_HOST_CONFIG) == 0) {
- au_writel(0x00d02000, USB_HOST_CONFIG);
- au_readl(USB_HOST_CONFIG);
- udelay(1000);
- }
- /* enable host controller */
- au_writel(USBH_ENABLE_CE | au_readl(USB_HOST_CONFIG), USB_HOST_CONFIG);
- au_readl(USB_HOST_CONFIG);
- udelay(1000);
- au_writel(USBH_ENABLE_INIT | au_readl(USB_HOST_CONFIG),
- USB_HOST_CONFIG);
- au_readl(USB_HOST_CONFIG);
+ /* enable clock to EHCI block and HS PHY PLL*/
+ au_writel(au_readl(USB_HOST_CONFIG) | USBH_ENABLE_CE, USB_HOST_CONFIG);
+ au_sync();
udelay(1000);
- pr_debug(__FILE__ ": Clock to USB host has been enabled\n");
+ /* enable EHCI mmio */
+ au_writel(au_readl(USB_HOST_CONFIG) | USBH_ENABLE_INIT, USB_HOST_CONFIG);
+ au_sync();
+ udelay(1000);
}
-static void au1xxx_stop_ehc(struct platform_device *dev)
+static void au1xxx_stop_ehc(void)
{
- pr_debug(__FILE__ ": stopping Au1xxx EHCI USB Controller\n");
+ unsigned long c;
/* Disable mem */
- au_writel(~USBH_DISABLE & au_readl(USB_HOST_CONFIG), USB_HOST_CONFIG);
+ au_writel(au_readl(USB_HOST_CONFIG) & ~USBH_DISABLE, USB_HOST_CONFIG);
+ au_sync();
udelay(1000);
- /* Disable clock */
- au_writel(~USB_MCFG_EHCCLKEN & au_readl(USB_HOST_CONFIG),
- USB_HOST_CONFIG);
- au_readl(USB_HOST_CONFIG);
+
+ /* Disable EHC clock. If the HS PHY is unused disable it too. */
+ c = au_readl(USB_HOST_CONFIG) & ~USB_MCFG_EHCCLKEN;
+ if (!(c & USB_MCFG_UCECLKEN)) /* UDC disabled? */
+ c &= ~USB_MCFG_PHYPLLEN; /* yes: disable HS PHY PLL */
+ au_writel(c, USB_HOST_CONFIG);
+ au_sync();
}
-/*-------------------------------------------------------------------------*/
+static const struct hc_driver ehci_au1xxx_hc_driver = {
+ .description = hcd_name,
+ .product_desc = "Au1xxx EHCI",
+ .hcd_priv_size = sizeof(struct ehci_hcd),
-/* configure so an HC device and id are always provided */
-/* always called with process context; sleeping is OK */
+ /*
+ * generic hardware linkage
+ */
+ .irq = ehci_irq,
+ .flags = HCD_MEMORY | HCD_USB2,
-/**
- * usb_ehci_au1xxx_probe - initialize Au1xxx-based HCDs
- * Context: !in_interrupt()
- *
- * Allocates basic resources for this USB host controller, and
- * then invokes the start() method for the HCD associated with it
- * through the hotplug entry's driver_data.
- *
- */
-int usb_ehci_au1xxx_probe(const struct hc_driver *driver,
- struct usb_hcd **hcd_out, struct platform_device *dev)
+ /*
+ * basic lifecycle operations
+ *
+ * FIXME -- ehci_init() doesn't do enough here.
+ * See ehci-ppc-soc for a complete implementation.
+ */
+ .reset = ehci_init,
+ .start = ehci_run,
+ .stop = ehci_stop,
+ .shutdown = ehci_shutdown,
+
+ /*
+ * managing i/o requests and associated device resources
+ */
+ .urb_enqueue = ehci_urb_enqueue,
+ .urb_dequeue = ehci_urb_dequeue,
+ .endpoint_disable = ehci_endpoint_disable,
+
+ /*
+ * scheduling support
+ */
+ .get_frame_number = ehci_get_frame,
+
+ /*
+ * root hub support
+ */
+ .hub_status_data = ehci_hub_status_data,
+ .hub_control = ehci_hub_control,
+ .bus_suspend = ehci_bus_suspend,
+ .bus_resume = ehci_bus_resume,
+ .relinquish_port = ehci_relinquish_port,
+ .port_handed_over = ehci_port_handed_over,
+};
+
+static int ehci_hcd_au1xxx_drv_probe(struct platform_device *pdev)
{
- int retval;
struct usb_hcd *hcd;
struct ehci_hcd *ehci;
+ int ret;
-#if defined(CONFIG_SOC_AU1200) && defined(CONFIG_DMA_COHERENT)
+ if (usb_disabled())
+ return -ENODEV;
+#if defined(CONFIG_SOC_AU1200) && defined(CONFIG_DMA_COHERENT)
/* Au1200 AB USB does not support coherent memory */
if (!(read_c0_prid() & 0xff)) {
- pr_info("%s: this is chip revision AB!\n", dev->name);
- pr_info("%s: update your board or re-configure the kernel\n",
- dev->name);
+ printk(KERN_INFO "%s: this is chip revision AB!\n", pdev->name);
+ printk(KERN_INFO "%s: update your board or re-configure"
+ " the kernel\n", pdev->name);
return -ENODEV;
}
#endif
- au1xxx_start_ehc(dev);
-
- if (dev->resource[1].flags != IORESOURCE_IRQ) {
+ if (pdev->resource[1].flags != IORESOURCE_IRQ) {
pr_debug("resource[1] is not IORESOURCE_IRQ");
- retval = -ENOMEM;
+ return -ENOMEM;
}
- hcd = usb_create_hcd(driver, &dev->dev, "Au1xxx");
+ hcd = usb_create_hcd(&ehci_au1xxx_hc_driver, &pdev->dev, "Au1xxx");
if (!hcd)
return -ENOMEM;
- hcd->rsrc_start = dev->resource[0].start;
- hcd->rsrc_len = dev->resource[0].end - dev->resource[0].start + 1;
+
+ hcd->rsrc_start = pdev->resource[0].start;
+ hcd->rsrc_len = pdev->resource[0].end - pdev->resource[0].start + 1;
if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len, hcd_name)) {
pr_debug("request_mem_region failed");
- retval = -EBUSY;
+ ret = -EBUSY;
goto err1;
}
hcd->regs = ioremap(hcd->rsrc_start, hcd->rsrc_len);
if (!hcd->regs) {
pr_debug("ioremap failed");
- retval = -ENOMEM;
+ ret = -ENOMEM;
goto err2;
}
+ au1xxx_start_ehc();
+
ehci = hcd_to_ehci(hcd);
ehci->caps = hcd->regs;
ehci->regs = hcd->regs + HC_LENGTH(readl(&ehci->caps->hc_capbase));
/* cache this readonly data; minimize chip reads */
ehci->hcs_params = readl(&ehci->caps->hcs_params);
- /* ehci_hcd_init(hcd_to_ehci(hcd)); */
-
- retval =
- usb_add_hcd(hcd, dev->resource[1].start, IRQF_DISABLED | IRQF_SHARED);
- if (retval == 0)
- return retval;
+ ret = usb_add_hcd(hcd, pdev->resource[1].start,
+ IRQF_DISABLED | IRQF_SHARED);
+ if (ret == 0) {
+ platform_set_drvdata(pdev, hcd);
+ return ret;
+ }
- au1xxx_stop_ehc(dev);
+ au1xxx_stop_ehc();
iounmap(hcd->regs);
err2:
release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
err1:
usb_put_hcd(hcd);
- return retval;
+ return ret;
}
-/* may be called without controller electrically present */
-/* may be called with controller, bus, and devices active */
-
-/**
- * usb_ehci_hcd_au1xxx_remove - shutdown processing for Au1xxx-based HCDs
- * @dev: USB Host Controller being removed
- * Context: !in_interrupt()
- *
- * Reverses the effect of usb_ehci_hcd_au1xxx_probe(), first invoking
- * the HCD's stop() method. It is always called from a thread
- * context, normally "rmmod", "apmd", or something similar.
- *
- */
-void usb_ehci_au1xxx_remove(struct usb_hcd *hcd, struct platform_device *dev)
+static int ehci_hcd_au1xxx_drv_remove(struct platform_device *pdev)
{
+ struct usb_hcd *hcd = platform_get_drvdata(pdev);
+
usb_remove_hcd(hcd);
iounmap(hcd->regs);
release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
usb_put_hcd(hcd);
- au1xxx_stop_ehc(dev);
-}
-
-/*-------------------------------------------------------------------------*/
+ au1xxx_stop_ehc();
+ platform_set_drvdata(pdev, NULL);
-static const struct hc_driver ehci_au1xxx_hc_driver = {
- .description = hcd_name,
- .product_desc = "Au1xxx EHCI",
- .hcd_priv_size = sizeof(struct ehci_hcd),
-
- /*
- * generic hardware linkage
- */
- .irq = ehci_irq,
- .flags = HCD_MEMORY | HCD_USB2,
-
- /*
- * basic lifecycle operations
- *
- * FIXME -- ehci_init() doesn't do enough here.
- * See ehci-ppc-soc for a complete implementation.
- */
- .reset = ehci_init,
- .start = ehci_run,
- .stop = ehci_stop,
- .shutdown = ehci_shutdown,
-
- /*
- * managing i/o requests and associated device resources
- */
- .urb_enqueue = ehci_urb_enqueue,
- .urb_dequeue = ehci_urb_dequeue,
- .endpoint_disable = ehci_endpoint_disable,
-
- /*
- * scheduling support
- */
- .get_frame_number = ehci_get_frame,
-
- /*
- * root hub support
- */
- .hub_status_data = ehci_hub_status_data,
- .hub_control = ehci_hub_control,
- .bus_suspend = ehci_bus_suspend,
- .bus_resume = ehci_bus_resume,
- .relinquish_port = ehci_relinquish_port,
- .port_handed_over = ehci_port_handed_over,
-};
-
-/*-------------------------------------------------------------------------*/
-
-static int ehci_hcd_au1xxx_drv_probe(struct platform_device *pdev)
-{
- struct usb_hcd *hcd = NULL;
- int ret;
-
- pr_debug("In ehci_hcd_au1xxx_drv_probe\n");
-
- if (usb_disabled())
- return -ENODEV;
-
- /* FIXME we only want one one probe() not two */
- ret = usb_ehci_au1xxx_probe(&ehci_au1xxx_hc_driver, &hcd, pdev);
- return ret;
-}
-
-static int ehci_hcd_au1xxx_drv_remove(struct platform_device *pdev)
-{
- struct usb_hcd *hcd = platform_get_drvdata(pdev);
-
- /* FIXME we only want one one remove() not two */
- usb_ehci_au1xxx_remove(hcd, pdev);
return 0;
}
return 0;
}
*/
-MODULE_ALIAS("platform:au1xxx-ehci");
+
static struct platform_driver ehci_hcd_au1xxx_driver = {
- .probe = ehci_hcd_au1xxx_drv_probe,
- .remove = ehci_hcd_au1xxx_drv_remove,
- .shutdown = usb_hcd_platform_shutdown,
+ .probe = ehci_hcd_au1xxx_drv_probe,
+ .remove = ehci_hcd_au1xxx_drv_remove,
+ .shutdown = usb_hcd_platform_shutdown,
/*.suspend = ehci_hcd_au1xxx_drv_suspend, */
/*.resume = ehci_hcd_au1xxx_drv_resume, */
.driver = {
- .name = "au1xxx-ehci",
+ .name = "au1xxx-ehci",
+ .owner = THIS_MODULE,
}
};
+
+MODULE_ALIAS("platform:au1xxx-ehci");
#ifdef __LITTLE_ENDIAN
#define USBH_ENABLE_INIT (USBH_ENABLE_CE | USBH_ENABLE_E | USBH_ENABLE_C)
#elif __BIG_ENDIAN
-#define USBH_ENABLE_INIT (USBH_ENABLE_CE | USBH_ENABLE_E | USBH_ENABLE_C | USBH_ENABLE_BE)
+#define USBH_ENABLE_INIT (USBH_ENABLE_CE | USBH_ENABLE_E | USBH_ENABLE_C | \
+ USBH_ENABLE_BE)
#else
#error not byte order defined
#endif
#define USB_MCFG_RDCOMB (1<<30)
#define USB_MCFG_SSDEN (1<<23)
#define USB_MCFG_OHCCLKEN (1<<16)
+#ifdef CONFIG_DMA_COHERENT
#define USB_MCFG_UCAM (1<<7)
+#else
+#define USB_MCFG_UCAM (0)
+#endif
#define USB_MCFG_OBMEN (1<<1)
#define USB_MCFG_OMEMEN (1<<0)
#define USBH_ENABLE_CE USB_MCFG_OHCCLKEN
-#ifdef CONFIG_DMA_COHERENT
-#define USBH_ENABLE_INIT (USB_MCFG_OHCCLKEN \
- | USB_MCFG_PFEN | USB_MCFG_RDCOMB \
- | USB_MCFG_SSDEN | USB_MCFG_UCAM \
- | USB_MCFG_OBMEN | USB_MCFG_OMEMEN)
-#else
-#define USBH_ENABLE_INIT (USB_MCFG_OHCCLKEN \
- | USB_MCFG_PFEN | USB_MCFG_RDCOMB \
- | USB_MCFG_SSDEN \
- | USB_MCFG_OBMEN | USB_MCFG_OMEMEN)
-#endif
+
+#define USBH_ENABLE_INIT (USB_MCFG_PFEN | USB_MCFG_RDCOMB | \
+ USBH_ENABLE_CE | USB_MCFG_SSDEN | \
+ USB_MCFG_UCAM | \
+ USB_MCFG_OBMEN | USB_MCFG_OMEMEN)
+
#define USBH_DISABLE (USB_MCFG_OBMEN | USB_MCFG_OMEMEN)
#endif /* Au1200 */
extern int usb_disabled(void);
-/*-------------------------------------------------------------------------*/
-
-static void au1xxx_start_ohc(struct platform_device *dev)
+static void au1xxx_start_ohc(void)
{
- printk(KERN_DEBUG __FILE__
- ": starting Au1xxx OHCI USB Controller\n");
-
/* enable host controller */
-
#ifndef CONFIG_SOC_AU1200
-
au_writel(USBH_ENABLE_CE, USB_HOST_CONFIG);
- udelay(1000);
- au_writel(USBH_ENABLE_INIT, USB_HOST_CONFIG);
+ au_sync();
udelay(1000);
-#else /* Au1200 */
-
- /* write HW defaults again in case Yamon cleared them */
- if (au_readl(USB_HOST_CONFIG) == 0) {
- au_writel(0x00d02000, USB_HOST_CONFIG);
- au_readl(USB_HOST_CONFIG);
- udelay(1000);
- }
- au_writel(USBH_ENABLE_CE | au_readl(USB_HOST_CONFIG), USB_HOST_CONFIG);
- au_readl(USB_HOST_CONFIG);
+ au_writel(au_readl(USB_HOST_CONFIG) | USBH_ENABLE_INIT, USB_HOST_CONFIG);
+ au_sync();
udelay(1000);
- au_writel(USBH_ENABLE_INIT | au_readl(USB_HOST_CONFIG), USB_HOST_CONFIG);
- au_readl(USB_HOST_CONFIG);
- udelay(1000);
-
-#endif /* Au1200 */
-#ifndef CONFIG_SOC_AU1200
/* wait for reset complete (read register twice; see au1500 errata) */
while (au_readl(USB_HOST_CONFIG),
!(au_readl(USB_HOST_CONFIG) & USBH_ENABLE_RD))
-#endif
udelay(1000);
- printk(KERN_DEBUG __FILE__
- ": Clock to USB host has been enabled \n");
-}
-
-static void au1xxx_stop_ohc(struct platform_device *dev)
-{
- printk(KERN_DEBUG __FILE__
- ": stopping Au1xxx OHCI USB Controller\n");
-
-#ifndef CONFIG_SOC_AU1200
-
- /* Disable clock */
- au_writel(au_readl(USB_HOST_CONFIG) & ~USBH_ENABLE_CE, USB_HOST_CONFIG);
-
#else /* Au1200 */
-
- /* Disable mem */
- au_writel(~USBH_DISABLE & au_readl(USB_HOST_CONFIG), USB_HOST_CONFIG);
+ au_writel(au_readl(USB_HOST_CONFIG) | USBH_ENABLE_CE, USB_HOST_CONFIG);
+ au_sync();
udelay(1000);
- /* Disable clock */
- au_writel(~USBH_ENABLE_CE & au_readl(USB_HOST_CONFIG), USB_HOST_CONFIG);
- au_readl(USB_HOST_CONFIG);
+
+ au_writel(au_readl(USB_HOST_CONFIG) | USBH_ENABLE_INIT, USB_HOST_CONFIG);
+ au_sync();
+ udelay(2000);
#endif /* Au1200 */
}
-
-/*-------------------------------------------------------------------------*/
-
-/* configure so an HC device and id are always provided */
-/* always called with process context; sleeping is OK */
-
-
-/**
- * usb_ohci_au1xxx_probe - initialize Au1xxx-based HCDs
- * Context: !in_interrupt()
- *
- * Allocates basic resources for this USB host controller, and
- * then invokes the start() method for the HCD associated with it
- * through the hotplug entry's driver_data.
- *
- */
-static int usb_ohci_au1xxx_probe(const struct hc_driver *driver,
- struct platform_device *dev)
+static void au1xxx_stop_ohc(void)
{
- int retval;
- struct usb_hcd *hcd;
-
-#if defined(CONFIG_SOC_AU1200) && defined(CONFIG_DMA_COHERENT)
- /* Au1200 AB USB does not support coherent memory */
- if (!(read_c0_prid() & 0xff)) {
- pr_info("%s: this is chip revision AB !!\n",
- dev->name);
- pr_info("%s: update your board or re-configure the kernel\n",
- dev->name);
- return -ENODEV;
- }
+#ifdef CONFIG_SOC_AU1200
+ /* Disable mem */
+ au_writel(au_readl(USB_HOST_CONFIG) & ~USBH_DISABLE, USB_HOST_CONFIG);
+ au_sync();
+ udelay(1000);
#endif
-
- if (dev->resource[1].flags != IORESOURCE_IRQ) {
- pr_debug("resource[1] is not IORESOURCE_IRQ\n");
- return -ENOMEM;
- }
-
- hcd = usb_create_hcd(driver, &dev->dev, "au1xxx");
- if (!hcd)
- return -ENOMEM;
- hcd->rsrc_start = dev->resource[0].start;
- hcd->rsrc_len = dev->resource[0].end - dev->resource[0].start + 1;
-
- if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len, hcd_name)) {
- pr_debug("request_mem_region failed\n");
- retval = -EBUSY;
- goto err1;
- }
-
- hcd->regs = ioremap(hcd->rsrc_start, hcd->rsrc_len);
- if (!hcd->regs) {
- pr_debug("ioremap failed\n");
- retval = -ENOMEM;
- goto err2;
- }
-
- au1xxx_start_ohc(dev);
- ohci_hcd_init(hcd_to_ohci(hcd));
-
- retval = usb_add_hcd(hcd, dev->resource[1].start, IRQF_DISABLED | IRQF_SHARED);
- if (retval == 0)
- return retval;
-
- au1xxx_stop_ohc(dev);
- iounmap(hcd->regs);
- err2:
- release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
- err1:
- usb_put_hcd(hcd);
- return retval;
-}
-
-
-/* may be called without controller electrically present */
-/* may be called with controller, bus, and devices active */
-
-/**
- * usb_hcd_au1xxx_remove - shutdown processing for Au1xxx-based HCDs
- * @dev: USB Host Controller being removed
- * Context: !in_interrupt()
- *
- * Reverses the effect of usb_hcd_au1xxx_probe(), first invoking
- * the HCD's stop() method. It is always called from a thread
- * context, normally "rmmod", "apmd", or something similar.
- *
- */
-static void usb_ohci_au1xxx_remove(struct usb_hcd *hcd, struct platform_device *dev)
-{
- usb_remove_hcd(hcd);
- au1xxx_stop_ohc(dev);
- iounmap(hcd->regs);
- release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
- usb_put_hcd(hcd);
+ /* Disable clock */
+ au_writel(au_readl(USB_HOST_CONFIG) & ~USBH_ENABLE_CE, USB_HOST_CONFIG);
+ au_sync();
}
-/*-------------------------------------------------------------------------*/
-
-static int __devinit
-ohci_au1xxx_start (struct usb_hcd *hcd)
+static int __devinit ohci_au1xxx_start(struct usb_hcd *hcd)
{
- struct ohci_hcd *ohci = hcd_to_ohci (hcd);
- int ret;
+ struct ohci_hcd *ohci = hcd_to_ohci(hcd);
+ int ret;
- ohci_dbg (ohci, "ohci_au1xxx_start, ohci:%p", ohci);
+ ohci_dbg(ohci, "ohci_au1xxx_start, ohci:%p", ohci);
- if ((ret = ohci_init (ohci)) < 0)
+ if ((ret = ohci_init(ohci)) < 0)
return ret;
- if ((ret = ohci_run (ohci)) < 0) {
+ if ((ret = ohci_run(ohci)) < 0) {
err ("can't start %s", hcd->self.bus_name);
- ohci_stop (hcd);
+ ohci_stop(hcd);
return ret;
}
return 0;
}
-/*-------------------------------------------------------------------------*/
-
static const struct hc_driver ohci_au1xxx_hc_driver = {
.description = hcd_name,
.product_desc = "Au1xxx OHCI",
.start_port_reset = ohci_start_port_reset,
};
-/*-------------------------------------------------------------------------*/
-
static int ohci_hcd_au1xxx_drv_probe(struct platform_device *pdev)
{
int ret;
-
- pr_debug ("In ohci_hcd_au1xxx_drv_probe");
+ struct usb_hcd *hcd;
if (usb_disabled())
return -ENODEV;
- ret = usb_ohci_au1xxx_probe(&ohci_au1xxx_hc_driver, pdev);
+#if defined(CONFIG_SOC_AU1200) && defined(CONFIG_DMA_COHERENT)
+ /* Au1200 AB USB does not support coherent memory */
+ if (!(read_c0_prid() & 0xff)) {
+ printk(KERN_INFO "%s: this is chip revision AB !!\n",
+ pdev->name);
+ printk(KERN_INFO "%s: update your board or re-configure "
+ "the kernel\n", pdev->name);
+ return -ENODEV;
+ }
+#endif
+
+ if (pdev->resource[1].flags != IORESOURCE_IRQ) {
+ pr_debug("resource[1] is not IORESOURCE_IRQ\n");
+ return -ENOMEM;
+ }
+
+ hcd = usb_create_hcd(&ohci_au1xxx_hc_driver, &pdev->dev, "au1xxx");
+ if (!hcd)
+ return -ENOMEM;
+
+ hcd->rsrc_start = pdev->resource[0].start;
+ hcd->rsrc_len = pdev->resource[0].end - pdev->resource[0].start + 1;
+
+ if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len, hcd_name)) {
+ pr_debug("request_mem_region failed\n");
+ ret = -EBUSY;
+ goto err1;
+ }
+
+ hcd->regs = ioremap(hcd->rsrc_start, hcd->rsrc_len);
+ if (!hcd->regs) {
+ pr_debug("ioremap failed\n");
+ ret = -ENOMEM;
+ goto err2;
+ }
+
+ au1xxx_start_ohc();
+ ohci_hcd_init(hcd_to_ohci(hcd));
+
+ ret = usb_add_hcd(hcd, pdev->resource[1].start,
+ IRQF_DISABLED | IRQF_SHARED);
+ if (ret == 0) {
+ platform_set_drvdata(pdev, hcd);
+ return ret;
+ }
+
+ au1xxx_stop_ohc();
+ iounmap(hcd->regs);
+err2:
+ release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
+err1:
+ usb_put_hcd(hcd);
return ret;
}
{
struct usb_hcd *hcd = platform_get_drvdata(pdev);
- usb_ohci_au1xxx_remove(hcd, pdev);
+ usb_remove_hcd(hcd);
+ au1xxx_stop_ohc();
+ iounmap(hcd->regs);
+ release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
+ usb_put_hcd(hcd);
+ platform_set_drvdata(pdev, NULL);
+
return 0;
}
+
/*TBD*/
/*static int ohci_hcd_au1xxx_drv_suspend(struct platform_device *dev)
{
git://ftp.safe.ca / safe / jmp / linux-2.6 / commitdiff