endchoice
+menu "Freescale Ethernet driver platform-specific options"
+ depends on FS_ENET
+
+ config MPC8xx_SECOND_ETH
+ bool "Second Ethernet channel"
+ depends on (MPC885ADS || MPC86XADS)
+ default y
+ help
+ This enables support for second Ethernet on MPC885ADS and MPC86xADS boards.
+ The latter will use SCC1, for 885ADS you can select it below.
+
+ choice
+ prompt "Second Ethernet channel"
+ depends on MPC8xx_SECOND_ETH
+ default MPC8xx_SECOND_ETH_FEC2
+
+ config MPC8xx_SECOND_ETH_FEC2
+ bool "FEC2"
+ depends on MPC885ADS
+ help
+ Enable FEC2 to serve as 2-nd Ethernet channel. Note that SMC2
+ (often 2-nd UART) will not work if this is enabled.
+
+ config MPC8xx_SECOND_ETH_SCC1
+ bool "SCC1"
+ depends on MPC86XADS
+ select MPC8xx_SCC_ENET_FIXED
+ help
+ Enable SCC1 to serve as 2-nd Ethernet channel. Note that SMC1
+ (often 1-nd UART) will not work if this is enabled.
+
+ config MPC8xx_SECOND_ETH_SCC3
+ bool "SCC3"
+ depends on MPC885ADS
+ help
+ Enable SCC3 to serve as 2-nd Ethernet channel. Note that SMC1
+ (often 1-nd UART) will not work if this is enabled.
+
+ endchoice
+
+ config MPC8xx_SCC_ENET_FIXED
+ depends on MPC8xx_SECOND_ETH_SCC
+ default n
+ bool "Use fixed MII-less mode for SCC Ethernet"
+
+endmenu
+
choice
prompt "Machine Type"
depends on 6xx || POWER3
obj-$(CONFIG_SPRUCE) += spruce.o
obj-$(CONFIG_LITE5200) += lite5200.o
obj-$(CONFIG_EV64360) += ev64360.o
+obj-$(CONFIG_MPC86XADS) += mpc866ads_setup.o
+obj-$(CONFIG_MPC885ADS) += mpc885ads_setup.o
+obj-$(CONFIG_ADS8272) += mpc8272ads_setup.o
ifeq ($(CONFIG_SMP),y)
obj-$(CONFIG_PPC_CHRP) += chrp_smp.o
/* CPM Ethernet through SCC1 or SCC2 */
-#ifdef CONFIG_SCC1_ENET /* Probably 860 variant */
+#if defined(CONFIG_SCC1_ENET) || defined(CONFIG_MPC8xx_SECOND_ETH_SCC1) /* Probably 860 variant */
/* Bits in parallel I/O port registers that have to be set/cleared
* to configure the pins for SCC1 use.
* TCLK - CLK1, RCLK - CLK2.
--- /dev/null
+/*
+ * arch/ppc/platforms/82xx/pq2ads_pd.c
+ *
+ * MPC82xx Board-specific PlatformDevice descriptions
+ *
+ * 2005 (c) MontaVista Software, Inc.
+ * Vitaly Bordug <vbordug@ru.mvista.com>
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/device.h>
+#include <linux/ioport.h>
+#include <linux/fs_enet_pd.h>
+#include <linux/platform_device.h>
+
+#include <asm/io.h>
+#include <asm/mpc8260.h>
+#include <asm/cpm2.h>
+#include <asm/immap_cpm2.h>
+#include <asm/irq.h>
+#include <asm/ppc_sys.h>
+#include <asm/ppcboot.h>
+
+#include "pq2ads_pd.h"
+
+static void init_fcc1_ioports(void);
+static void init_fcc2_ioports(void);
+
+static struct fs_mii_bus_info mii_bus_info = {
+ .method = fsmii_bitbang,
+ .id = 0,
+ .i.bitbang = {
+ .mdio_port = fsiop_portc,
+ .mdio_bit = 18,
+ .mdc_port = fsiop_portc,
+ .mdc_bit = 19,
+ .delay = 1,
+ },
+};
+
+static struct fs_platform_info mpc82xx_fcc1_pdata = {
+ .fs_no = fsid_fcc1,
+ .cp_page = CPM_CR_FCC1_PAGE,
+ .cp_block = CPM_CR_FCC1_SBLOCK,
+ .clk_trx = (PC_F1RXCLK | PC_F1TXCLK),
+ .clk_route = CMX1_CLK_ROUTE,
+ .clk_mask = CMX1_CLK_MASK,
+ .init_ioports = init_fcc1_ioports,
+
+ .phy_addr = 0,
+#ifdef PHY_INTERRUPT
+ .phy_irq = PHY_INTERRUPT,
+#else
+ .phy_irq = -1;
+#endif
+ .mem_offset = FCC1_MEM_OFFSET,
+ .bus_info = &mii_bus_info,
+ .rx_ring = 32,
+ .tx_ring = 32,
+ .rx_copybreak = 240,
+ .use_napi = 0,
+ .napi_weight = 17,
+};
+
+static struct fs_platform_info mpc82xx_fcc2_pdata = {
+ .fs_no = fsid_fcc2,
+ .cp_page = CPM_CR_FCC2_PAGE,
+ .cp_block = CPM_CR_FCC2_SBLOCK,
+ .clk_trx = (PC_F2RXCLK | PC_F2TXCLK),
+ .clk_route = CMX2_CLK_ROUTE,
+ .clk_mask = CMX2_CLK_MASK,
+ .init_ioports = init_fcc2_ioports,
+
+ .phy_addr = 3,
+#ifdef PHY_INTERRUPT
+ .phy_irq = PHY_INTERRUPT,
+#else
+ .phy_irq = -1;
+#endif
+ .mem_offset = FCC2_MEM_OFFSET,
+ .bus_info = &mii_bus_info,
+ .rx_ring = 32,
+ .tx_ring = 32,
+ .rx_copybreak = 240,
+ .use_napi = 0,
+ .napi_weight = 17,
+};
+
+static void init_fcc1_ioports(void)
+{
+ struct io_port *io;
+ u32 tempval;
+ cpm2_map_t* immap = ioremap(CPM_MAP_ADDR, sizeof(cpm2_map_t));
+ u32 *bcsr = ioremap(BCSR_ADDR+4, sizeof(u32));
+
+ io = &immap->im_ioport;
+
+ /* Enable the PHY */
+ clrbits32(bcsr, BCSR1_FETHIEN);
+ setbits32(bcsr, BCSR1_FETH_RST);
+
+ /* FCC1 pins are on port A/C. */
+ /* Configure port A and C pins for FCC1 Ethernet. */
+
+ tempval = in_be32(&io->iop_pdira);
+ tempval &= ~PA1_DIRA0;
+ tempval |= PA1_DIRA1;
+ out_be32(&io->iop_pdira, tempval);
+
+ tempval = in_be32(&io->iop_psora);
+ tempval &= ~PA1_PSORA0;
+ tempval |= PA1_PSORA1;
+ out_be32(&io->iop_psora, tempval);
+
+ setbits32(&io->iop_ppara,PA1_DIRA0 | PA1_DIRA1);
+
+ /* Alter clocks */
+ tempval = PC_F1TXCLK|PC_F1RXCLK;
+
+ clrbits32(&io->iop_psorc, tempval);
+ clrbits32(&io->iop_pdirc, tempval);
+ setbits32(&io->iop_pparc, tempval);
+
+ clrbits32(&immap->im_cpmux.cmx_fcr, CMX1_CLK_MASK);
+ setbits32(&immap->im_cpmux.cmx_fcr, CMX1_CLK_ROUTE);
+ iounmap(bcsr);
+ iounmap(immap);
+}
+
+static void init_fcc2_ioports(void)
+{
+ cpm2_map_t* immap = ioremap(CPM_MAP_ADDR, sizeof(cpm2_map_t));
+ u32 *bcsr = ioremap(BCSR_ADDR+12, sizeof(u32));
+
+ struct io_port *io;
+ u32 tempval;
+
+ immap = cpm2_immr;
+
+ io = &immap->im_ioport;
+
+ /* Enable the PHY */
+ clrbits32(bcsr, BCSR3_FETHIEN2);
+ setbits32(bcsr, BCSR3_FETH2_RST);
+
+ /* FCC2 are port B/C. */
+ /* Configure port A and C pins for FCC2 Ethernet. */
+
+ tempval = in_be32(&io->iop_pdirb);
+ tempval &= ~PB2_DIRB0;
+ tempval |= PB2_DIRB1;
+ out_be32(&io->iop_pdirb, tempval);
+
+ tempval = in_be32(&io->iop_psorb);
+ tempval &= ~PB2_PSORB0;
+ tempval |= PB2_PSORB1;
+ out_be32(&io->iop_psorb, tempval);
+
+ setbits32(&io->iop_pparb,PB2_DIRB0 | PB2_DIRB1);
+
+ tempval = PC_F2RXCLK|PC_F2TXCLK;
+
+ /* Alter clocks */
+ clrbits32(&io->iop_psorc,tempval);
+ clrbits32(&io->iop_pdirc,tempval);
+ setbits32(&io->iop_pparc,tempval);
+
+ clrbits32(&immap->im_cpmux.cmx_fcr, CMX2_CLK_MASK);
+ setbits32(&immap->im_cpmux.cmx_fcr, CMX2_CLK_ROUTE);
+
+ iounmap(bcsr);
+ iounmap(immap);
+}
+
+
+static void __init mpc8272ads_fixup_enet_pdata(struct platform_device *pdev,
+ int idx)
+{
+ bd_t* bi = (void*)__res;
+ int fs_no = fsid_fcc1+pdev->id-1;
+
+ mpc82xx_fcc1_pdata.dpram_offset = mpc82xx_fcc2_pdata.dpram_offset = (u32)cpm2_immr->im_dprambase;
+ mpc82xx_fcc1_pdata.fcc_regs_c = mpc82xx_fcc2_pdata.fcc_regs_c = (u32)cpm2_immr->im_fcc_c;
+
+ switch(fs_no) {
+ case fsid_fcc1:
+ memcpy(&mpc82xx_fcc1_pdata.macaddr,bi->bi_enetaddr,6);
+ pdev->dev.platform_data = &mpc82xx_fcc1_pdata;
+ break;
+ case fsid_fcc2:
+ memcpy(&mpc82xx_fcc2_pdata.macaddr,bi->bi_enetaddr,6);
+ mpc82xx_fcc2_pdata.macaddr[5] ^= 1;
+ pdev->dev.platform_data = &mpc82xx_fcc2_pdata;
+ break;
+ }
+}
+
+static int mpc8272ads_platform_notify(struct device *dev)
+{
+ static const struct platform_notify_dev_map dev_map[] = {
+ {
+ .bus_id = "fsl-cpm-fcc",
+ .rtn = mpc8272ads_fixup_enet_pdata
+ },
+ {
+ .bus_id = NULL
+ }
+ };
+ platform_notify_map(dev_map,dev);
+
+ return 0;
+
+}
+
+int __init mpc8272ads_init(void)
+{
+ printk(KERN_NOTICE "mpc8272ads: Init\n");
+
+ platform_notify = mpc8272ads_platform_notify;
+
+ ppc_sys_device_initfunc();
+
+ ppc_sys_device_disable_all();
+ ppc_sys_device_enable(MPC82xx_CPM_FCC1);
+ ppc_sys_device_enable(MPC82xx_CPM_FCC2);
+
+ return 0;
+}
+
+arch_initcall(mpc8272ads_init);
--- /dev/null
+/*arch/ppc/platforms/mpc885ads-setup.c
+ *
+ * Platform setup for the Freescale mpc885ads board
+ *
+ * Vitaly Bordug <vbordug@ru.mvista.com>
+ *
+ * Copyright 2005 MontaVista Software Inc.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+#include <linux/config.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/param.h>
+#include <linux/string.h>
+#include <linux/ioport.h>
+#include <linux/device.h>
+
+#include <linux/fs_enet_pd.h>
+#include <linux/mii.h>
+
+#include <asm/delay.h>
+#include <asm/io.h>
+#include <asm/machdep.h>
+#include <asm/page.h>
+#include <asm/processor.h>
+#include <asm/system.h>
+#include <asm/time.h>
+#include <asm/ppcboot.h>
+#include <asm/8xx_immap.h>
+#include <asm/commproc.h>
+#include <asm/ppc_sys.h>
+#include <asm/mpc8xx.h>
+
+extern unsigned char __res[];
+
+static struct fs_mii_bus_info fec_mii_bus_info = {
+ .method = fsmii_fec,
+ .id = 0,
+};
+
+static struct fs_mii_bus_info scc_mii_bus_info = {
+ .method = fsmii_fixed,
+ .id = 0,
+ .i.fixed.speed = 10,
+ .i.fixed.duplex = 0,
+};
+
+static struct fs_platform_info mpc8xx_fec_pdata[] = {
+ {
+ .rx_ring = 128,
+ .tx_ring = 16,
+ .rx_copybreak = 240,
+
+ .use_napi = 1,
+ .napi_weight = 17,
+
+ .phy_addr = 15,
+ .phy_irq = -1,
+
+ .use_rmii = 0,
+
+ .bus_info = &fec_mii_bus_info,
+ }
+};
+
+static struct fs_platform_info mpc8xx_scc_pdata = {
+ .rx_ring = 64,
+ .tx_ring = 8,
+ .rx_copybreak = 240,
+
+ .use_napi = 1,
+ .napi_weight = 17,
+
+ .phy_addr = -1,
+ .phy_irq = -1,
+
+ .bus_info = &scc_mii_bus_info,
+};
+
+void __init board_init(void)
+{
+ volatile cpm8xx_t *cp = cpmp;
+ unsigned *bcsr_io;
+
+ bcsr_io = ioremap(BCSR1, sizeof(unsigned long));
+
+ if (bcsr_io == NULL) {
+ printk(KERN_CRIT "Could not remap BCSR1\n");
+ return;
+ }
+#ifdef CONFIG_SERIAL_CPM_SMC1
+ cp->cp_simode &= ~(0xe0000000 >> 17); /* brg1 */
+ clrbits32(bcsr_io,(0x80000000 >> 7));
+#else
+ setbits32(bcsr_io,(0x80000000 >> 7));
+
+ cp->cp_pbpar &= ~(0x000000c0);
+ cp->cp_pbdir |= 0x000000c0;
+ cp->cp_smc[0].smc_smcmr = 0;
+ cp->cp_smc[0].smc_smce = 0;
+#endif
+
+#ifdef CONFIG_SERIAL_CPM_SMC2
+ cp->cp_simode &= ~(0xe0000000 >> 1);
+ cp->cp_simode |= (0x20000000 >> 1); /* brg2 */
+ clrbits32(bcsr_io,(0x80000000 >> 13));
+#else
+ clrbits32(bcsr_io,(0x80000000 >> 13));
+ cp->cp_pbpar &= ~(0x00000c00);
+ cp->cp_pbdir |= 0x00000c00;
+ cp->cp_smc[1].smc_smcmr = 0;
+ cp->cp_smc[1].smc_smce = 0;
+#endif
+ iounmap(bcsr_io);
+}
+
+static void setup_fec1_ioports(void)
+{
+ immap_t *immap = (immap_t *) IMAP_ADDR;
+
+ setbits16(&immap->im_ioport.iop_pdpar, 0x1fff);
+ setbits16(&immap->im_ioport.iop_pddir, 0x1fff);
+}
+
+static void setup_scc1_ioports(void)
+{
+ immap_t *immap = (immap_t *) IMAP_ADDR;
+ unsigned *bcsr_io;
+
+ bcsr_io = ioremap(BCSR1, sizeof(unsigned long));
+
+ if (bcsr_io == NULL) {
+ printk(KERN_CRIT "Could not remap BCSR1\n");
+ return;
+ }
+
+ /* Enable the PHY.
+ */
+ clrbits32(bcsr_io,BCSR1_ETHEN);
+
+ /* Configure port A pins for Txd and Rxd.
+ */
+ /* Disable receive and transmit in case EPPC-Bug started it.
+ */
+ setbits16(&immap->im_ioport.iop_papar, PA_ENET_RXD | PA_ENET_TXD);
+ clrbits16(&immap->im_ioport.iop_padir, PA_ENET_RXD | PA_ENET_TXD);
+ clrbits16(&immap->im_ioport.iop_paodr, PA_ENET_TXD);
+
+ /* Configure port C pins to enable CLSN and RENA.
+ */
+ clrbits16(&immap->im_ioport.iop_pcpar, PC_ENET_CLSN | PC_ENET_RENA);
+ clrbits16(&immap->im_ioport.iop_pcdir, PC_ENET_CLSN | PC_ENET_RENA);
+ setbits16(&immap->im_ioport.iop_pcso, PC_ENET_CLSN | PC_ENET_RENA);
+ /* Configure port A for TCLK and RCLK.
+ */
+ setbits16(&immap->im_ioport.iop_papar, PA_ENET_TCLK | PA_ENET_RCLK);
+ clrbits16(&immap->im_ioport.iop_padir, PA_ENET_TCLK | PA_ENET_RCLK);
+ clrbits32(&immap->im_cpm.cp_pbpar, PB_ENET_TENA);
+ clrbits32(&immap->im_cpm.cp_pbdir, PB_ENET_TENA);
+
+ /* Configure Serial Interface clock routing.
+ * First, clear all SCC bits to zero, then set the ones we want.
+ */
+ clrbits32(&immap->im_cpm.cp_sicr, SICR_ENET_MASK);
+ setbits32(&immap->im_cpm.cp_sicr, SICR_ENET_CLKRT);
+
+ /* In the original SCC enet driver the following code is placed at
+ the end of the initialization */
+ setbits32(&immap->im_cpm.cp_pbpar, PB_ENET_TENA);
+ setbits32(&immap->im_cpm.cp_pbdir, PB_ENET_TENA);
+
+}
+
+static void mpc866ads_fixup_enet_pdata(struct platform_device *pdev, int fs_no)
+{
+ struct fs_platform_info *fpi = pdev->dev.platform_data;
+
+ volatile cpm8xx_t *cp;
+ bd_t *bd = (bd_t *) __res;
+ char *e;
+ int i;
+
+ /* Get pointer to Communication Processor */
+ cp = cpmp;
+ switch (fs_no) {
+ case fsid_fec1:
+ fpi = &mpc8xx_fec_pdata[0];
+ fpi->init_ioports = &setup_fec1_ioports;
+
+ break;
+ case fsid_scc1:
+ fpi = &mpc8xx_scc_pdata;
+ fpi->init_ioports = &setup_scc1_ioports;
+
+ break;
+ default:
+ printk(KERN_WARNING"Device %s is not supported!\n", pdev->name);
+ return;
+ }
+
+ pdev->dev.platform_data = fpi;
+ fpi->fs_no = fs_no;
+
+ e = (unsigned char *)&bd->bi_enetaddr;
+ for (i = 0; i < 6; i++)
+ fpi->macaddr[i] = *e++;
+
+ fpi->macaddr[5 - pdev->id]++;
+
+}
+
+static void mpc866ads_fixup_fec_enet_pdata(struct platform_device *pdev,
+ int idx)
+{
+ /* This is for FEC devices only */
+ if (!pdev || !pdev->name || (!strstr(pdev->name, "fsl-cpm-fec")))
+ return;
+ mpc866ads_fixup_enet_pdata(pdev, fsid_fec1 + pdev->id - 1);
+}
+
+static void mpc866ads_fixup_scc_enet_pdata(struct platform_device *pdev,
+ int idx)
+{
+ /* This is for SCC devices only */
+ if (!pdev || !pdev->name || (!strstr(pdev->name, "fsl-cpm-scc")))
+ return;
+
+ mpc866ads_fixup_enet_pdata(pdev, fsid_scc1 + pdev->id - 1);
+}
+
+static int mpc866ads_platform_notify(struct device *dev)
+{
+ static const struct platform_notify_dev_map dev_map[] = {
+ {
+ .bus_id = "fsl-cpm-fec",
+ .rtn = mpc866ads_fixup_fec_enet_pdata,
+ },
+ {
+ .bus_id = "fsl-cpm-scc",
+ .rtn = mpc866ads_fixup_scc_enet_pdata,
+ },
+ {
+ .bus_id = NULL
+ }
+ };
+
+ platform_notify_map(dev_map,dev);
+
+ return 0;
+}
+
+int __init mpc866ads_init(void)
+{
+ printk(KERN_NOTICE "mpc866ads: Init\n");
+
+ platform_notify = mpc866ads_platform_notify;
+
+ ppc_sys_device_initfunc();
+ ppc_sys_device_disable_all();
+
+#ifdef MPC8xx_SECOND_ETH_SCC1
+ ppc_sys_device_enable(MPC8xx_CPM_SCC1);
+#endif
+ ppc_sys_device_enable(MPC8xx_CPM_FEC1);
+
+ return 0;
+}
+
+arch_initcall(mpc866ads_init);
--- /dev/null
+/*arch/ppc/platforms/mpc885ads-setup.c
+ *
+ * Platform setup for the Freescale mpc885ads board
+ *
+ * Vitaly Bordug <vbordug@ru.mvista.com>
+ *
+ * Copyright 2005 MontaVista Software Inc.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+#include <linux/config.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/param.h>
+#include <linux/string.h>
+#include <linux/ioport.h>
+#include <linux/device.h>
+
+#include <linux/fs_enet_pd.h>
+#include <linux/mii.h>
+
+#include <asm/delay.h>
+#include <asm/io.h>
+#include <asm/machdep.h>
+#include <asm/page.h>
+#include <asm/processor.h>
+#include <asm/system.h>
+#include <asm/time.h>
+#include <asm/ppcboot.h>
+#include <asm/8xx_immap.h>
+#include <asm/commproc.h>
+#include <asm/ppc_sys.h>
+
+extern unsigned char __res[];
+
+static void __init mpc885ads_scc_phy_init(char);
+
+static struct fs_mii_bus_info fec_mii_bus_info = {
+ .method = fsmii_fec,
+ .id = 0,
+};
+
+static struct fs_mii_bus_info scc_mii_bus_info = {
+#ifdef CONFIG_SCC_ENET_8xx_FIXED
+ .method = fsmii_fixed,
+#else
+ .method = fsmii_fec,
+#endif
+
+ .id = 0,
+};
+
+static struct fs_platform_info mpc8xx_fec_pdata[] = {
+ {
+ .rx_ring = 128,
+ .tx_ring = 16,
+ .rx_copybreak = 240,
+
+ .use_napi = 1,
+ .napi_weight = 17,
+
+ .phy_addr = 0,
+ .phy_irq = SIU_IRQ7,
+
+ .bus_info = &fec_mii_bus_info,
+ }, {
+ .rx_ring = 128,
+ .tx_ring = 16,
+ .rx_copybreak = 240,
+
+ .use_napi = 1,
+ .napi_weight = 17,
+
+ .phy_addr = 1,
+ .phy_irq = SIU_IRQ7,
+
+ .bus_info = &fec_mii_bus_info,
+ }
+};
+
+static struct fs_platform_info mpc8xx_scc_pdata = {
+ .rx_ring = 64,
+ .tx_ring = 8,
+ .rx_copybreak = 240,
+
+ .use_napi = 1,
+ .napi_weight = 17,
+
+ .phy_addr = 2,
+#ifdef CONFIG_MPC8xx_SCC_ENET_FIXED
+ .phy_irq = -1,
+#else
+ .phy_irq = SIU_IRQ7,
+#endif
+
+ .bus_info = &scc_mii_bus_info,
+};
+
+void __init board_init(void)
+{
+ volatile cpm8xx_t *cp = cpmp;
+ unsigned int *bcsr_io;
+
+#ifdef CONFIG_FS_ENET
+ immap_t *immap = (immap_t *) IMAP_ADDR;
+#endif
+ bcsr_io = ioremap(BCSR1, sizeof(unsigned long));
+
+ if (bcsr_io == NULL) {
+ printk(KERN_CRIT "Could not remap BCSR\n");
+ return;
+ }
+#ifdef CONFIG_SERIAL_CPM_SMC1
+ cp->cp_simode &= ~(0xe0000000 >> 17); /* brg1 */
+ clrbits32(bcsr_io, BCSR1_RS232EN_1);
+#else
+ setbits32(bcsr_io,BCSR1_RS232EN_1);
+ cp->cp_smc[0].smc_smcmr = 0;
+ cp->cp_smc[0].smc_smce = 0;
+#endif
+
+#ifdef CONFIG_SERIAL_CPM_SMC2
+ cp->cp_simode &= ~(0xe0000000 >> 1);
+ cp->cp_simode |= (0x20000000 >> 1); /* brg2 */
+ clrbits32(bcsr_io,BCSR1_RS232EN_2);
+#else
+ setbits32(bcsr_io,BCSR1_RS232EN_2);
+ cp->cp_smc[1].smc_smcmr = 0;
+ cp->cp_smc[1].smc_smce = 0;
+#endif
+ iounmap(bcsr_io);
+
+#ifdef CONFIG_FS_ENET
+ /* use MDC for MII (common) */
+ setbits16(&immap->im_ioport.iop_pdpar, 0x0080);
+ clrbits16(&immap->im_ioport.iop_pddir, 0x0080);
+#endif
+}
+
+static void setup_fec1_ioports(void)
+{
+ immap_t *immap = (immap_t *) IMAP_ADDR;
+
+ /* configure FEC1 pins */
+ setbits16(&immap->im_ioport.iop_papar, 0xf830);
+ setbits16(&immap->im_ioport.iop_padir, 0x0830);
+ clrbits16(&immap->im_ioport.iop_padir, 0xf000);
+ setbits32(&immap->im_cpm.cp_pbpar, 0x00001001);
+
+ clrbits32(&immap->im_cpm.cp_pbdir, 0x00001001);
+ setbits16(&immap->im_ioport.iop_pcpar, 0x000c);
+ clrbits16(&immap->im_ioport.iop_pcdir, 0x000c);
+ setbits32(&immap->im_cpm.cp_pepar, 0x00000003);
+
+ setbits32(&immap->im_cpm.cp_pedir, 0x00000003);
+ clrbits32(&immap->im_cpm.cp_peso, 0x00000003);
+ clrbits32(&immap->im_cpm.cp_cptr, 0x00000100);
+}
+
+static void setup_fec2_ioports(void)
+{
+ immap_t *immap = (immap_t *) IMAP_ADDR;
+
+ /* configure FEC2 pins */
+ setbits32(&immap->im_cpm.cp_pepar, 0x0003fffc);
+ setbits32(&immap->im_cpm.cp_pedir, 0x0003fffc);
+ setbits32(&immap->im_cpm.cp_peso, 0x00037800);
+ clrbits32(&immap->im_cpm.cp_peso, 0x000087fc);
+ clrbits32(&immap->im_cpm.cp_cptr, 0x00000080);
+}
+
+static void setup_scc3_ioports(void)
+{
+ immap_t *immap = (immap_t *) IMAP_ADDR;
+ unsigned *bcsr_io;
+
+ bcsr_io = ioremap(BCSR_ADDR, BCSR_SIZE);
+
+ if (bcsr_io == NULL) {
+ printk(KERN_CRIT "Could not remap BCSR\n");
+ return;
+ }
+
+ /* Enable the PHY.
+ */
+ setbits32(bcsr_io+4, BCSR4_ETH10_RST);
+ /* Configure port A pins for Txd and Rxd.
+ */
+ setbits16(&immap->im_ioport.iop_papar, PA_ENET_RXD | PA_ENET_TXD);
+ clrbits16(&immap->im_ioport.iop_padir, PA_ENET_RXD | PA_ENET_TXD);
+
+ /* Configure port C pins to enable CLSN and RENA.
+ */
+ clrbits16(&immap->im_ioport.iop_pcpar, PC_ENET_CLSN | PC_ENET_RENA);
+ clrbits16(&immap->im_ioport.iop_pcdir, PC_ENET_CLSN | PC_ENET_RENA);
+ setbits16(&immap->im_ioport.iop_pcso, PC_ENET_CLSN | PC_ENET_RENA);
+
+ /* Configure port E for TCLK and RCLK.
+ */
+ setbits32(&immap->im_cpm.cp_pepar, PE_ENET_TCLK | PE_ENET_RCLK);
+ clrbits32(&immap->im_cpm.cp_pepar, PE_ENET_TENA);
+ clrbits32(&immap->im_cpm.cp_pedir,
+ PE_ENET_TCLK | PE_ENET_RCLK | PE_ENET_TENA);
+ clrbits32(&immap->im_cpm.cp_peso, PE_ENET_TCLK | PE_ENET_RCLK);
+ setbits32(&immap->im_cpm.cp_peso, PE_ENET_TENA);
+
+ /* Configure Serial Interface clock routing.
+ * First, clear all SCC bits to zero, then set the ones we want.
+ */
+ clrbits32(&immap->im_cpm.cp_sicr, SICR_ENET_MASK);
+ setbits32(&immap->im_cpm.cp_sicr, SICR_ENET_CLKRT);
+
+ /* Disable Rx and Tx. SMC1 sshould be stopped if SCC3 eternet are used.
+ */
+ immap->im_cpm.cp_smc[0].smc_smcmr &= ~(SMCMR_REN | SMCMR_TEN);
+ /* On the MPC885ADS SCC ethernet PHY is initialized in the full duplex mode
+ * by H/W setting after reset. SCC ethernet controller support only half duplex.
+ * This discrepancy of modes causes a lot of carrier lost errors.
+ */
+
+ /* In the original SCC enet driver the following code is placed at
+ the end of the initialization */
+ setbits32(&immap->im_cpm.cp_pepar, PE_ENET_TENA);
+ clrbits32(&immap->im_cpm.cp_pedir, PE_ENET_TENA);
+ setbits32(&immap->im_cpm.cp_peso, PE_ENET_TENA);
+
+ setbits32(bcsr_io+1, BCSR1_ETHEN);
+ iounmap(bcsr_io);
+}
+
+static void mpc885ads_fixup_enet_pdata(struct platform_device *pdev, int fs_no)
+{
+ struct fs_platform_info *fpi = pdev->dev.platform_data;
+
+ volatile cpm8xx_t *cp;
+ bd_t *bd = (bd_t *) __res;
+ char *e;
+ int i;
+
+ /* Get pointer to Communication Processor */
+ cp = cpmp;
+ switch (fs_no) {
+ case fsid_fec1:
+ fpi = &mpc8xx_fec_pdata[0];
+ fpi->init_ioports = &setup_fec1_ioports;
+ break;
+ case fsid_fec2:
+ fpi = &mpc8xx_fec_pdata[1];
+ fpi->init_ioports = &setup_fec2_ioports;
+ break;
+ case fsid_scc3:
+ fpi = &mpc8xx_scc_pdata;
+ fpi->init_ioports = &setup_scc3_ioports;
+ mpc885ads_scc_phy_init(fpi->phy_addr);
+ break;
+ default:
+ printk(KERN_WARNING"Device %s is not supported!\n", pdev->name);
+ return;
+ }
+
+ pdev->dev.platform_data = fpi;
+ fpi->fs_no = fs_no;
+
+ e = (unsigned char *)&bd->bi_enetaddr;
+ for (i = 0; i < 6; i++)
+ fpi->macaddr[i] = *e++;
+
+ fpi->macaddr[5 - pdev->id]++;
+
+}
+
+static void mpc885ads_fixup_fec_enet_pdata(struct platform_device *pdev,
+ int idx)
+{
+ /* This is for FEC devices only */
+ if (!pdev || !pdev->name || (!strstr(pdev->name, "fsl-cpm-fec")))
+ return;
+ mpc885ads_fixup_enet_pdata(pdev, fsid_fec1 + pdev->id - 1);
+}
+
+static void __init mpc885ads_fixup_scc_enet_pdata(struct platform_device *pdev,
+ int idx)
+{
+ /* This is for SCC devices only */
+ if (!pdev || !pdev->name || (!strstr(pdev->name, "fsl-cpm-scc")))
+ return;
+
+ mpc885ads_fixup_enet_pdata(pdev, fsid_scc1 + pdev->id - 1);
+}
+
+/* SCC ethernet controller does not have MII management channel. FEC1 MII
+ * channel is used to communicate with the 10Mbit PHY.
+ */
+
+#define MII_ECNTRL_PINMUX 0x4
+#define FEC_ECNTRL_PINMUX 0x00000004
+#define FEC_RCNTRL_MII_MODE 0x00000004
+
+/* Make MII read/write commands.
+ */
+#define mk_mii_write(REG, VAL, PHY_ADDR) (0x50020000 | (((REG) & 0x1f) << 18) | \
+ ((VAL) & 0xffff) | ((PHY_ADDR) << 23))
+
+static void mpc885ads_scc_phy_init(char phy_addr)
+{
+ volatile immap_t *immap;
+ volatile fec_t *fecp;
+ bd_t *bd;
+
+ bd = (bd_t *) __res;
+ immap = (immap_t *) IMAP_ADDR; /* pointer to internal registers */
+ fecp = &(immap->im_cpm.cp_fec);
+
+ /* Enable MII pins of the FEC1
+ */
+ setbits16(&immap->im_ioport.iop_pdpar, 0x0080);
+ clrbits16(&immap->im_ioport.iop_pddir, 0x0080);
+ /* Set MII speed to 2.5 MHz
+ */
+ out_be32(&fecp->fec_mii_speed,
+ ((((bd->bi_intfreq + 4999999) / 2500000) / 2) & 0x3F) << 1);
+
+ /* Enable FEC pin MUX
+ */
+ setbits32(&fecp->fec_ecntrl, MII_ECNTRL_PINMUX);
+ setbits32(&fecp->fec_r_cntrl, FEC_RCNTRL_MII_MODE);
+
+ out_be32(&fecp->fec_mii_data,
+ mk_mii_write(MII_BMCR, BMCR_ISOLATE, phy_addr));
+ udelay(100);
+ out_be32(&fecp->fec_mii_data,
+ mk_mii_write(MII_ADVERTISE,
+ ADVERTISE_10HALF | ADVERTISE_CSMA, phy_addr));
+ udelay(100);
+
+ /* Disable FEC MII settings
+ */
+ clrbits32(&fecp->fec_ecntrl, MII_ECNTRL_PINMUX);
+ clrbits32(&fecp->fec_r_cntrl, FEC_RCNTRL_MII_MODE);
+ out_be32(&fecp->fec_mii_speed, 0);
+}
+
+static int mpc885ads_platform_notify(struct device *dev)
+{
+
+ static const struct platform_notify_dev_map dev_map[] = {
+ {
+ .bus_id = "fsl-cpm-fec",
+ .rtn = mpc885ads_fixup_fec_enet_pdata,
+ },
+ {
+ .bus_id = "fsl-cpm-scc",
+ .rtn = mpc885ads_fixup_scc_enet_pdata,
+ },
+ {
+ .bus_id = NULL
+ }
+ };
+
+ platform_notify_map(dev_map,dev);
+
+}
+
+int __init mpc885ads_init(void)
+{
+ printk(KERN_NOTICE "mpc885ads: Init\n");
+
+ platform_notify = mpc885ads_platform_notify;
+
+ ppc_sys_device_initfunc();
+ ppc_sys_device_disable_all();
+
+ ppc_sys_device_enable(MPC8xx_CPM_FEC1);
+
+#ifdef CONFIG_MPC8xx_SECOND_ETH_SCC3
+ ppc_sys_device_enable(MPC8xx_CPM_SCC1);
+
+#endif
+#ifdef CONFIG_MPC8xx_SECOND_ETH_FEC2
+ ppc_sys_device_enable(MPC8xx_CPM_FEC2);
+#endif
+
+ return 0;
+}
+
+arch_initcall(mpc885ads_init);
#include <asm/ppcboot.h>
+#if defined(CONFIG_ADS8272)
+#define BOARD_CHIP_NAME "8272"
+#endif
+
/* Memory map is configured by the PROM startup.
* We just map a few things we need. The CSR is actually 4 byte-wide
* registers that can be accessed as 8-, 16-, or 32-bit values.
--- /dev/null
+#ifndef __PQ2ADS_PD_H
+#define __PQ2ADS_PD_H
+/*
+ * arch/ppc/platforms/82xx/pq2ads_pd.h
+ *
+ * Some defines for MPC82xx board-specific PlatformDevice descriptions
+ *
+ * 2005 (c) MontaVista Software, Inc.
+ * Vitaly Bordug <vbordug@ru.mvista.com>
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+/* FCC1 Clock Source Configuration. These can be redefined in the board specific file.
+ Can only choose from CLK9-12 */
+
+#define F1_RXCLK 11
+#define F1_TXCLK 10
+
+/* FCC2 Clock Source Configuration. These can be redefined in the board specific file.
+ Can only choose from CLK13-16 */
+#define F2_RXCLK 15
+#define F2_TXCLK 16
+
+/* FCC3 Clock Source Configuration. These can be redefined in the board specific file.
+ Can only choose from CLK13-16 */
+#define F3_RXCLK 13
+#define F3_TXCLK 14
+
+/* Automatically generates register configurations */
+#define PC_CLK(x) ((uint)(1<<(x-1))) /* FCC CLK I/O ports */
+
+#define CMXFCR_RF1CS(x) ((uint)((x-5)<<27)) /* FCC1 Receive Clock Source */
+#define CMXFCR_TF1CS(x) ((uint)((x-5)<<24)) /* FCC1 Transmit Clock Source */
+#define CMXFCR_RF2CS(x) ((uint)((x-9)<<19)) /* FCC2 Receive Clock Source */
+#define CMXFCR_TF2CS(x) ((uint)((x-9)<<16)) /* FCC2 Transmit Clock Source */
+#define CMXFCR_RF3CS(x) ((uint)((x-9)<<11)) /* FCC3 Receive Clock Source */
+#define CMXFCR_TF3CS(x) ((uint)((x-9)<<8)) /* FCC3 Transmit Clock Source */
+
+#define PC_F1RXCLK PC_CLK(F1_RXCLK)
+#define PC_F1TXCLK PC_CLK(F1_TXCLK)
+#define CMX1_CLK_ROUTE (CMXFCR_RF1CS(F1_RXCLK) | CMXFCR_TF1CS(F1_TXCLK))
+#define CMX1_CLK_MASK ((uint)0xff000000)
+
+#define PC_F2RXCLK PC_CLK(F2_RXCLK)
+#define PC_F2TXCLK PC_CLK(F2_TXCLK)
+#define CMX2_CLK_ROUTE (CMXFCR_RF2CS(F2_RXCLK) | CMXFCR_TF2CS(F2_TXCLK))
+#define CMX2_CLK_MASK ((uint)0x00ff0000)
+
+#define PC_F3RXCLK PC_CLK(F3_RXCLK)
+#define PC_F3TXCLK PC_CLK(F3_TXCLK)
+#define CMX3_CLK_ROUTE (CMXFCR_RF3CS(F3_RXCLK) | CMXFCR_TF3CS(F3_TXCLK))
+#define CMX3_CLK_MASK ((uint)0x0000ff00)
+
+/* I/O Pin assignment for FCC1. I don't yet know the best way to do this,
+ * but there is little variation among the choices.
+ */
+#define PA1_COL 0x00000001U
+#define PA1_CRS 0x00000002U
+#define PA1_TXER 0x00000004U
+#define PA1_TXEN 0x00000008U
+#define PA1_RXDV 0x00000010U
+#define PA1_RXER 0x00000020U
+#define PA1_TXDAT 0x00003c00U
+#define PA1_RXDAT 0x0003c000U
+#define PA1_PSORA0 (PA1_RXDAT | PA1_TXDAT)
+#define PA1_PSORA1 (PA1_COL | PA1_CRS | PA1_TXER | PA1_TXEN | \
+ PA1_RXDV | PA1_RXER)
+#define PA1_DIRA0 (PA1_RXDAT | PA1_CRS | PA1_COL | PA1_RXER | PA1_RXDV)
+#define PA1_DIRA1 (PA1_TXDAT | PA1_TXEN | PA1_TXER)
+
+
+/* I/O Pin assignment for FCC2. I don't yet know the best way to do this,
+ * but there is little variation among the choices.
+ */
+#define PB2_TXER 0x00000001U
+#define PB2_RXDV 0x00000002U
+#define PB2_TXEN 0x00000004U
+#define PB2_RXER 0x00000008U
+#define PB2_COL 0x00000010U
+#define PB2_CRS 0x00000020U
+#define PB2_TXDAT 0x000003c0U
+#define PB2_RXDAT 0x00003c00U
+#define PB2_PSORB0 (PB2_RXDAT | PB2_TXDAT | PB2_CRS | PB2_COL | \
+ PB2_RXER | PB2_RXDV | PB2_TXER)
+#define PB2_PSORB1 (PB2_TXEN)
+#define PB2_DIRB0 (PB2_RXDAT | PB2_CRS | PB2_COL | PB2_RXER | PB2_RXDV)
+#define PB2_DIRB1 (PB2_TXDAT | PB2_TXEN | PB2_TXER)
+
+
+/* I/O Pin assignment for FCC3. I don't yet know the best way to do this,
+ * but there is little variation among the choices.
+ */
+#define PB3_RXDV 0x00004000U
+#define PB3_RXER 0x00008000U
+#define PB3_TXER 0x00010000U
+#define PB3_TXEN 0x00020000U
+#define PB3_COL 0x00040000U
+#define PB3_CRS 0x00080000U
+#define PB3_TXDAT 0x0f000000U
+#define PB3_RXDAT 0x00f00000U
+#define PB3_PSORB0 (PB3_RXDAT | PB3_TXDAT | PB3_CRS | PB3_COL | \
+ PB3_RXER | PB3_RXDV | PB3_TXER | PB3_TXEN)
+#define PB3_PSORB1 0
+#define PB3_DIRB0 (PB3_RXDAT | PB3_CRS | PB3_COL | PB3_RXER | PB3_RXDV)
+#define PB3_DIRB1 (PB3_TXDAT | PB3_TXEN | PB3_TXER)
+
+#define FCC_MEM_OFFSET(x) (CPM_FCC_SPECIAL_BASE + (x*128))
+#define FCC1_MEM_OFFSET FCC_MEM_OFFSET(0)
+#define FCC2_MEM_OFFSET FCC_MEM_OFFSET(1)
+
+#endif
git://ftp.safe.ca / safe / jmp / linux-2.6 / commitdiff