[WATCHDOG] pcwd.c control status patch

Clean-up the control status code (insert tabs where relevant),
Add new Control Status defines, Make sure that the R2DS bit
stays the same.

Signed-off-by: Wim Van Sebroeck <wim@iguana.be>

diff --git a/drivers/char/watchdog/pcwd.c b/drivers/char/watchdog/pcwd.c
index 8d6b249..c6e27e2 100644 (file)
--- a/drivers/char/watchdog/pcwd.c
+++ b/drivers/char/watchdog/pcwd.c
@@ -73,8 +73,8 @@
 #include <asm/io.h>            /* For inb/outb/... */
 
 /* Module and version information */
-#define WATCHDOG_VERSION "1.16"
-#define WATCHDOG_DATE "03 Jan 2006"
+#define WATCHDOG_VERSION "1.17"
+#define WATCHDOG_DATE "12 Feb 2006"
 #define WATCHDOG_DRIVER_NAME "ISA-PC Watchdog"
 #define WATCHDOG_NAME "pcwd"
 #define PFX WATCHDOG_NAME ": "
@@ -96,15 +96,19 @@
  * PCI-PC Watchdog card.
 */
 /* Port 1 : Control Status #1 for the PC Watchdog card, revision A. */
-#define WD_WDRST                0x01   /* Previously reset state */
-#define WD_T110                 0x02   /* Temperature overheat sense */
-#define WD_HRTBT                0x04   /* Heartbeat sense */
-#define WD_RLY2                 0x08   /* External relay triggered */
-#define WD_SRLY2                0x80   /* Software external relay triggered */
+#define WD_WDRST               0x01    /* Previously reset state */
+#define WD_T110                        0x02    /* Temperature overheat sense */
+#define WD_HRTBT               0x04    /* Heartbeat sense */
+#define WD_RLY2                        0x08    /* External relay triggered */
+#define WD_SRLY2               0x80    /* Software external relay triggered */
 /* Port 1 : Control Status #1 for the PC Watchdog card, revision C. */
-#define WD_REVC_WTRP            0x01   /* Watchdog Trip status */
-#define WD_REVC_HRBT            0x02   /* Watchdog Heartbeat */
-#define WD_REVC_TTRP            0x04   /* Temperature Trip status */
+#define WD_REVC_WTRP           0x01    /* Watchdog Trip status */
+#define WD_REVC_HRBT           0x02    /* Watchdog Heartbeat */
+#define WD_REVC_TTRP           0x04    /* Temperature Trip status */
+#define WD_REVC_RL2A           0x08    /* Relay 2 activated by on-board processor */
+#define WD_REVC_RL1A           0x10    /* Relay 1 active */
+#define WD_REVC_R2DS           0x40    /* Relay 2 disable */
+#define WD_REVC_RLY2           0x80    /* Relay 2 activated? */
 /* Port 2 : Control Status #2 */
 #define WD_WDIS                        0x10    /* Watchdog Disabled */
 #define WD_ENTP                        0x20    /* Watchdog Enable Temperature Trip */
@@ -407,7 +411,7 @@ static int pcwd_set_heartbeat(int t)
 
 static int pcwd_get_status(int *status)
 {
-       int card_status;
+       int control_status;
 
        *status=0;
        spin_lock(&pcwd_private.io_lock);
@@ -415,22 +419,22 @@ static int pcwd_get_status(int *status)
                /* Rev A cards return status information from
                 * the base register, which is used for the
                 * temperature in other cards. */
-               card_status = inb(pcwd_private.io_addr);
+               control_status = inb(pcwd_private.io_addr);
        else {
                /* Rev C cards return card status in the base
                 * address + 1 register. And use different bits
                 * to indicate a card initiated reset, and an
                 * over-temperature condition. And the reboot
                 * status can be reset. */
-               card_status = inb(pcwd_private.io_addr + 1);
+               control_status = inb(pcwd_private.io_addr + 1);
        }
        spin_unlock(&pcwd_private.io_lock);
 
        if (pcwd_private.revision == PCWD_REVISION_A) {
-               if (card_status & WD_WDRST)
+               if (control_status & WD_WDRST)
                        *status |= WDIOF_CARDRESET;
 
-               if (card_status & WD_T110) {
+               if (control_status & WD_T110) {
                        *status |= WDIOF_OVERHEAT;
                        if (temp_panic) {
                                printk (KERN_INFO PFX "Temperature overheat trip!\n");
@@ -438,10 +442,10 @@ static int pcwd_get_status(int *status)
                        }
                }
        } else {
-               if (card_status & WD_REVC_WTRP)
+               if (control_status & WD_REVC_WTRP)
                        *status |= WDIOF_CARDRESET;
 
-               if (card_status & WD_REVC_TTRP) {
+               if (control_status & WD_REVC_TTRP) {
                        *status |= WDIOF_OVERHEAT;
                        if (temp_panic) {
                                printk (KERN_INFO PFX "Temperature overheat trip!\n");
@@ -455,9 +459,16 @@ static int pcwd_get_status(int *status)
 
 static int pcwd_clear_status(void)
 {
+       int control_status;
+
        if (pcwd_private.revision == PCWD_REVISION_C) {
                spin_lock(&pcwd_private.io_lock);
-               outb_p(0x00, pcwd_private.io_addr + 1); /* clear reset status */
+
+               control_status = inb_p(pcwd_private.io_addr + 1);
+
+               /* clear reset status & Keep Relay 2 disable state as it is */
+               outb_p((control_status & WD_REVC_R2DS), pcwd_private.io_addr + 1);
+
                spin_unlock(&pcwd_private.io_lock);
        }
        return 0;