ARM: 5709/1: at91: add AC97 support to at91sam9g45 series and at91sam9m10g45ek board

Add the support of AC97 on the at91sam9g45 chip series and -ek board.
It will share the code with AVR32 ac97c alsa driver "atmel_ac97c".

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

diff --git a/arch/arm/mach-at91/at91sam9g45_devices.c b/arch/arm/mach-at91/at91sam9g45_devices.c
index 45720c8..d581cff 100644 (file)
--- a/arch/arm/mach-at91/at91sam9g45_devices.c
+++ b/arch/arm/mach-at91/at91sam9g45_devices.c
@@ -598,6 +598,61 @@ void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices)
 
 
 /* --------------------------------------------------------------------
+ *  AC97
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_SND_ATMEL_AC97C) || defined(CONFIG_SND_ATMEL_AC97C_MODULE)
+static u64 ac97_dmamask = DMA_BIT_MASK(32);
+static struct ac97c_platform_data ac97_data;
+
+static struct resource ac97_resources[] = {
+       [0] = {
+               .start  = AT91SAM9G45_BASE_AC97C,
+               .end    = AT91SAM9G45_BASE_AC97C + SZ_16K - 1,
+               .flags  = IORESOURCE_MEM,
+       },
+       [1] = {
+               .start  = AT91SAM9G45_ID_AC97C,
+               .end    = AT91SAM9G45_ID_AC97C,
+               .flags  = IORESOURCE_IRQ,
+       },
+};
+
+static struct platform_device at91sam9g45_ac97_device = {
+       .name           = "atmel_ac97c",
+       .id             = 0,
+       .dev            = {
+                               .dma_mask               = &ac97_dmamask,
+                               .coherent_dma_mask      = DMA_BIT_MASK(32),
+                               .platform_data          = &ac97_data,
+       },
+       .resource       = ac97_resources,
+       .num_resources  = ARRAY_SIZE(ac97_resources),
+};
+
+void __init at91_add_device_ac97(struct ac97c_platform_data *data)
+{
+       if (!data)
+               return;
+
+       at91_set_A_periph(AT91_PIN_PD8, 0);     /* AC97FS */
+       at91_set_A_periph(AT91_PIN_PD9, 0);     /* AC97CK */
+       at91_set_A_periph(AT91_PIN_PD7, 0);     /* AC97TX */
+       at91_set_A_periph(AT91_PIN_PD6, 0);     /* AC97RX */
+
+       /* reset */
+       if (data->reset_pin)
+               at91_set_gpio_output(data->reset_pin, 0);
+
+       ac97_data = *data;
+       platform_device_register(&at91sam9g45_ac97_device);
+}
+#else
+void __init at91_add_device_ac97(struct ac97c_platform_data *data) {}
+#endif
+
+
+/* --------------------------------------------------------------------
  *  LCD Controller
  * -------------------------------------------------------------------- */
 

diff --git a/arch/arm/mach-at91/board-sam9m10g45ek.c b/arch/arm/mach-at91/board-sam9m10g45ek.c
index b8558ea..64c3843 100644 (file)
--- a/arch/arm/mach-at91/board-sam9m10g45ek.c
+++ b/arch/arm/mach-at91/board-sam9m10g45ek.c
@@ -311,6 +311,14 @@ static void __init ek_add_device_buttons(void) {}
 
 
 /*
+ * AC97
+ * reset_pin is not connected: NRST
+ */
+static struct ac97c_platform_data ek_ac97_data = {
+};
+
+
+/*
  * LEDs ... these could all be PWM-driven, for variable brightness
  */
 static struct gpio_led ek_leds[] = {
@@ -372,6 +380,8 @@ static void __init ek_board_init(void)
        at91_add_device_lcdc(&ek_lcdc_data);
        /* Push Buttons */
        ek_add_device_buttons();
+       /* AC97 */
+       at91_add_device_ac97(&ek_ac97_data);
        /* LEDs */
        at91_gpio_leds(ek_leds, ARRAY_SIZE(ek_leds));
        at91_pwm_leds(ek_pwm_led, ARRAY_SIZE(ek_pwm_led));