cancel_delayed_work(&priv->thermal_periodic);
}
+/* check contents of special bootstrap uCode SRAM */
+static int iwl3945_verify_bsm(struct iwl_priv *priv)
+ {
+ __le32 *image = priv->ucode_boot.v_addr;
+ u32 len = priv->ucode_boot.len;
+ u32 reg;
+ u32 val;
+
+ IWL_DEBUG_INFO("Begin verify bsm\n");
+
+ /* verify BSM SRAM contents */
+ val = iwl_read_prph(priv, BSM_WR_DWCOUNT_REG);
+ for (reg = BSM_SRAM_LOWER_BOUND;
+ reg < BSM_SRAM_LOWER_BOUND + len;
+ reg += sizeof(u32), image++) {
+ val = iwl_read_prph(priv, reg);
+ if (val != le32_to_cpu(*image)) {
+ IWL_ERR(priv, "BSM uCode verification failed at "
+ "addr 0x%08X+%u (of %u), is 0x%x, s/b 0x%x\n",
+ BSM_SRAM_LOWER_BOUND,
+ reg - BSM_SRAM_LOWER_BOUND, len,
+ val, le32_to_cpu(*image));
+ return -EIO;
+ }
+ }
+
+ IWL_DEBUG_INFO("BSM bootstrap uCode image OK\n");
+
+ return 0;
+}
+
+ /**
+ * iwl3945_load_bsm - Load bootstrap instructions
+ *
+ * BSM operation:
+ *
+ * The Bootstrap State Machine (BSM) stores a short bootstrap uCode program
+ * in special SRAM that does not power down during RFKILL. When powering back
+ * up after power-saving sleeps (or during initial uCode load), the BSM loads
+ * the bootstrap program into the on-board processor, and starts it.
+ *
+ * The bootstrap program loads (via DMA) instructions and data for a new
+ * program from host DRAM locations indicated by the host driver in the
+ * BSM_DRAM_* registers. Once the new program is loaded, it starts
+ * automatically.
+ *
+ * When initializing the NIC, the host driver points the BSM to the
+ * "initialize" uCode image. This uCode sets up some internal data, then
+ * notifies host via "initialize alive" that it is complete.
+ *
+ * The host then replaces the BSM_DRAM_* pointer values to point to the
+ * normal runtime uCode instructions and a backup uCode data cache buffer
+ * (filled initially with starting data values for the on-board processor),
+ * then triggers the "initialize" uCode to load and launch the runtime uCode,
+ * which begins normal operation.
+ *
+ * When doing a power-save shutdown, runtime uCode saves data SRAM into
+ * the backup data cache in DRAM before SRAM is powered down.
+ *
+ * When powering back up, the BSM loads the bootstrap program. This reloads
+ * the runtime uCode instructions and the backup data cache into SRAM,
+ * and re-launches the runtime uCode from where it left off.
+ */
+static int iwl3945_load_bsm(struct iwl_priv *priv)
+{
+ __le32 *image = priv->ucode_boot.v_addr;
+ u32 len = priv->ucode_boot.len;
+ dma_addr_t pinst;
+ dma_addr_t pdata;
+ u32 inst_len;
+ u32 data_len;
+ int rc;
+ int i;
+ u32 done;
+ u32 reg_offset;
+
+ IWL_DEBUG_INFO("Begin load bsm\n");
+
+ /* make sure bootstrap program is no larger than BSM's SRAM size */
+ if (len > IWL39_MAX_BSM_SIZE)
+ return -EINVAL;
+
+ /* Tell bootstrap uCode where to find the "Initialize" uCode
+ * in host DRAM ... host DRAM physical address bits 31:0 for 3945.
+ * NOTE: iwl3945_initialize_alive_start() will replace these values,
+ * after the "initialize" uCode has run, to point to
+ * runtime/protocol instructions and backup data cache. */
+ pinst = priv->ucode_init.p_addr;
+ pdata = priv->ucode_init_data.p_addr;
+ inst_len = priv->ucode_init.len;
+ data_len = priv->ucode_init_data.len;
+
+ rc = iwl_grab_nic_access(priv);
+ if (rc)
+ return rc;
+
+ iwl_write_prph(priv, BSM_DRAM_INST_PTR_REG, pinst);
+ iwl_write_prph(priv, BSM_DRAM_DATA_PTR_REG, pdata);
+ iwl_write_prph(priv, BSM_DRAM_INST_BYTECOUNT_REG, inst_len);
+ iwl_write_prph(priv, BSM_DRAM_DATA_BYTECOUNT_REG, data_len);
+
+ /* Fill BSM memory with bootstrap instructions */
+ for (reg_offset = BSM_SRAM_LOWER_BOUND;
+ reg_offset < BSM_SRAM_LOWER_BOUND + len;
+ reg_offset += sizeof(u32), image++)
+ _iwl_write_prph(priv, reg_offset,
+ le32_to_cpu(*image));
+
+ rc = iwl3945_verify_bsm(priv);
+ if (rc) {
+ iwl_release_nic_access(priv);
+ return rc;
+ }
+
+ /* Tell BSM to copy from BSM SRAM into instruction SRAM, when asked */
+ iwl_write_prph(priv, BSM_WR_MEM_SRC_REG, 0x0);
+ iwl_write_prph(priv, BSM_WR_MEM_DST_REG,
+ IWL39_RTC_INST_LOWER_BOUND);
+ iwl_write_prph(priv, BSM_WR_DWCOUNT_REG, len / sizeof(u32));
+
+ /* Load bootstrap code into instruction SRAM now,
+ * to prepare to load "initialize" uCode */
+ iwl_write_prph(priv, BSM_WR_CTRL_REG,
+ BSM_WR_CTRL_REG_BIT_START);
+
+ /* Wait for load of bootstrap uCode to finish */
+ for (i = 0; i < 100; i++) {
+ done = iwl_read_prph(priv, BSM_WR_CTRL_REG);
+ if (!(done & BSM_WR_CTRL_REG_BIT_START))
+ break;
+ udelay(10);
+ }
+ if (i < 100)
+ IWL_DEBUG_INFO("BSM write complete, poll %d iterations\n", i);
+ else {
+ IWL_ERR(priv, "BSM write did not complete!\n");
+ return -EIO;
+ }
+
+ /* Enable future boot loads whenever power management unit triggers it
+ * (e.g. when powering back up after power-save shutdown) */
+ iwl_write_prph(priv, BSM_WR_CTRL_REG,
+ BSM_WR_CTRL_REG_BIT_START_EN);
+
+ iwl_release_nic_access(priv);
+
+ return 0;
+}
+
+static struct iwl_lib_ops iwl3945_lib = {
+ .load_ucode = iwl3945_load_bsm,
+};
+
+static struct iwl_ops iwl3945_ops = {
+ .lib = &iwl3945_lib,
+};
+
static struct iwl_cfg iwl3945_bg_cfg = {
.name = "3945BG",
.fw_name_pre = IWL3945_FW_PRE,
.ucode_api_max = IWL3945_UCODE_API_MAX,
.ucode_api_min = IWL3945_UCODE_API_MIN,
.sku = IWL_SKU_G,
+ .ops = &iwl3945_ops,
.mod_params = &iwl3945_mod_params
};
.ucode_api_max = IWL3945_UCODE_API_MAX,
.ucode_api_min = IWL3945_UCODE_API_MIN,
.sku = IWL_SKU_A|IWL_SKU_G,
+ .ops = &iwl3945_ops,
.mod_params = &iwl3945_mod_params
};
return rc;
}
-
-/* check contents of special bootstrap uCode SRAM */
-static int iwl3945_verify_bsm(struct iwl_priv *priv)
-{
- __le32 *image = priv->ucode_boot.v_addr;
- u32 len = priv->ucode_boot.len;
- u32 reg;
- u32 val;
-
- IWL_DEBUG_INFO("Begin verify bsm\n");
-
- /* verify BSM SRAM contents */
- val = iwl_read_prph(priv, BSM_WR_DWCOUNT_REG);
- for (reg = BSM_SRAM_LOWER_BOUND;
- reg < BSM_SRAM_LOWER_BOUND + len;
- reg += sizeof(u32), image++) {
- val = iwl_read_prph(priv, reg);
- if (val != le32_to_cpu(*image)) {
- IWL_ERR(priv, "BSM uCode verification failed at "
- "addr 0x%08X+%u (of %u), is 0x%x, s/b 0x%x\n",
- BSM_SRAM_LOWER_BOUND,
- reg - BSM_SRAM_LOWER_BOUND, len,
- val, le32_to_cpu(*image));
- return -EIO;
- }
- }
-
- IWL_DEBUG_INFO("BSM bootstrap uCode image OK\n");
-
- return 0;
-}
-
-/**
- * iwl3945_load_bsm - Load bootstrap instructions
- *
- * BSM operation:
- *
- * The Bootstrap State Machine (BSM) stores a short bootstrap uCode program
- * in special SRAM that does not power down during RFKILL. When powering back
- * up after power-saving sleeps (or during initial uCode load), the BSM loads
- * the bootstrap program into the on-board processor, and starts it.
- *
- * The bootstrap program loads (via DMA) instructions and data for a new
- * program from host DRAM locations indicated by the host driver in the
- * BSM_DRAM_* registers. Once the new program is loaded, it starts
- * automatically.
- *
- * When initializing the NIC, the host driver points the BSM to the
- * "initialize" uCode image. This uCode sets up some internal data, then
- * notifies host via "initialize alive" that it is complete.
- *
- * The host then replaces the BSM_DRAM_* pointer values to point to the
- * normal runtime uCode instructions and a backup uCode data cache buffer
- * (filled initially with starting data values for the on-board processor),
- * then triggers the "initialize" uCode to load and launch the runtime uCode,
- * which begins normal operation.
- *
- * When doing a power-save shutdown, runtime uCode saves data SRAM into
- * the backup data cache in DRAM before SRAM is powered down.
- *
- * When powering back up, the BSM loads the bootstrap program. This reloads
- * the runtime uCode instructions and the backup data cache into SRAM,
- * and re-launches the runtime uCode from where it left off.
- */
-static int iwl3945_load_bsm(struct iwl_priv *priv)
-{
- __le32 *image = priv->ucode_boot.v_addr;
- u32 len = priv->ucode_boot.len;
- dma_addr_t pinst;
- dma_addr_t pdata;
- u32 inst_len;
- u32 data_len;
- int rc;
- int i;
- u32 done;
- u32 reg_offset;
-
- IWL_DEBUG_INFO("Begin load bsm\n");
-
- /* make sure bootstrap program is no larger than BSM's SRAM size */
- if (len > IWL39_MAX_BSM_SIZE)
- return -EINVAL;
-
- /* Tell bootstrap uCode where to find the "Initialize" uCode
- * in host DRAM ... host DRAM physical address bits 31:0 for 3945.
- * NOTE: iwl3945_initialize_alive_start() will replace these values,
- * after the "initialize" uCode has run, to point to
- * runtime/protocol instructions and backup data cache. */
- pinst = priv->ucode_init.p_addr;
- pdata = priv->ucode_init_data.p_addr;
- inst_len = priv->ucode_init.len;
- data_len = priv->ucode_init_data.len;
-
- rc = iwl_grab_nic_access(priv);
- if (rc)
- return rc;
-
- iwl_write_prph(priv, BSM_DRAM_INST_PTR_REG, pinst);
- iwl_write_prph(priv, BSM_DRAM_DATA_PTR_REG, pdata);
- iwl_write_prph(priv, BSM_DRAM_INST_BYTECOUNT_REG, inst_len);
- iwl_write_prph(priv, BSM_DRAM_DATA_BYTECOUNT_REG, data_len);
-
- /* Fill BSM memory with bootstrap instructions */
- for (reg_offset = BSM_SRAM_LOWER_BOUND;
- reg_offset < BSM_SRAM_LOWER_BOUND + len;
- reg_offset += sizeof(u32), image++)
- _iwl_write_prph(priv, reg_offset,
- le32_to_cpu(*image));
-
- rc = iwl3945_verify_bsm(priv);
- if (rc) {
- iwl_release_nic_access(priv);
- return rc;
- }
-
- /* Tell BSM to copy from BSM SRAM into instruction SRAM, when asked */
- iwl_write_prph(priv, BSM_WR_MEM_SRC_REG, 0x0);
- iwl_write_prph(priv, BSM_WR_MEM_DST_REG,
- IWL39_RTC_INST_LOWER_BOUND);
- iwl_write_prph(priv, BSM_WR_DWCOUNT_REG, len / sizeof(u32));
-
- /* Load bootstrap code into instruction SRAM now,
- * to prepare to load "initialize" uCode */
- iwl_write_prph(priv, BSM_WR_CTRL_REG,
- BSM_WR_CTRL_REG_BIT_START);
-
- /* Wait for load of bootstrap uCode to finish */
- for (i = 0; i < 100; i++) {
- done = iwl_read_prph(priv, BSM_WR_CTRL_REG);
- if (!(done & BSM_WR_CTRL_REG_BIT_START))
- break;
- udelay(10);
- }
- if (i < 100)
- IWL_DEBUG_INFO("BSM write complete, poll %d iterations\n", i);
- else {
- IWL_ERR(priv, "BSM write did not complete!\n");
- return -EIO;
- }
-
- /* Enable future boot loads whenever power management unit triggers it
- * (e.g. when powering back up after power-save shutdown) */
- iwl_write_prph(priv, BSM_WR_CTRL_REG,
- BSM_WR_CTRL_REG_BIT_START_EN);
-
- iwl_release_nic_access(priv);
-
- return 0;
-}
-
static void iwl3945_nic_start(struct iwl_priv *priv)
{
/* Remove all resets to allow NIC to operate */
/* load bootstrap state machine,
* load bootstrap program into processor's memory,
* prepare to load the "initialize" uCode */
- rc = iwl3945_load_bsm(priv);
+ priv->cfg->ops->lib->load_ucode(priv);
if (rc) {
IWL_ERR(priv,
git://ftp.safe.ca / safe / jmp / linux-2.6 / commitdiff