X-Git-Url: http://ftp.safe.ca/?a=blobdiff_plain;f=include%2Fnet%2Fcfg80211.h;h=5389afdc129756abcef4c088b2c7adfd84165670;hb=e4e72fb4de93e3d4047a4ee3f08778422e17ed0d;hp=0e85ec39b6380de904efe8c2ac0c89b3cb6f12e0;hpb=60719ffd721f6764b7d07ca188c0d944a4330b69;p=safe%2Fjmp%2Flinux-2.6

diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h
index 0e85ec3..5389afd 100644
--- a/include/net/cfg80211.h
+++ b/include/net/cfg80211.h
@@ -4,7 +4,13 @@
 #include <linux/netlink.h>
 #include <linux/skbuff.h>
 #include <linux/nl80211.h>
+#include <linux/if_ether.h>
+#include <linux/ieee80211.h>
+#include <linux/wireless.h>
+#include <net/iw_handler.h>
 #include <net/genetlink.h>
+/* remove once we remove the wext stuff */
+#include <net/iw_handler.h>
 
 /*
  * 802.11 configuration in-kernel interface
@@ -110,12 +116,14 @@ struct beacon_parameters {
  * @STATION_FLAG_SHORT_PREAMBLE: station is capable of receiving frames
  *	with short preambles
  * @STATION_FLAG_WME: station is WME/QoS capable
+ * @STATION_FLAG_MFP: station uses management frame protection
  */
 enum station_flags {
 	STATION_FLAG_CHANGED		= 1<<0,
 	STATION_FLAG_AUTHORIZED		= 1<<NL80211_STA_FLAG_AUTHORIZED,
 	STATION_FLAG_SHORT_PREAMBLE	= 1<<NL80211_STA_FLAG_SHORT_PREAMBLE,
 	STATION_FLAG_WME		= 1<<NL80211_STA_FLAG_WME,
+	STATION_FLAG_MFP		= 1<<NL80211_STA_FLAG_MFP,
 };
 
 /**
@@ -167,6 +175,11 @@ struct station_parameters {
  * @STATION_INFO_LLID: @llid filled
  * @STATION_INFO_PLID: @plid filled
  * @STATION_INFO_PLINK_STATE: @plink_state filled
+ * @STATION_INFO_SIGNAL: @signal filled
+ * @STATION_INFO_TX_BITRATE: @tx_bitrate fields are filled
+ *  (tx_bitrate, tx_bitrate_flags and tx_bitrate_mcs)
+ * @STATION_INFO_RX_PACKETS: @rx_packets filled
+ * @STATION_INFO_TX_PACKETS: @tx_packets filled
  */
 enum station_info_flags {
 	STATION_INFO_INACTIVE_TIME	= 1<<0,
@@ -175,6 +188,41 @@ enum station_info_flags {
 	STATION_INFO_LLID		= 1<<3,
 	STATION_INFO_PLID		= 1<<4,
 	STATION_INFO_PLINK_STATE	= 1<<5,
+	STATION_INFO_SIGNAL		= 1<<6,
+	STATION_INFO_TX_BITRATE		= 1<<7,
+	STATION_INFO_RX_PACKETS		= 1<<8,
+	STATION_INFO_TX_PACKETS		= 1<<9,
+};
+
+/**
+ * enum station_info_rate_flags - bitrate info flags
+ *
+ * Used by the driver to indicate the specific rate transmission
+ * type for 802.11n transmissions.
+ *
+ * @RATE_INFO_FLAGS_MCS: @tx_bitrate_mcs filled
+ * @RATE_INFO_FLAGS_40_MHZ_WIDTH: 40 Mhz width transmission
+ * @RATE_INFO_FLAGS_SHORT_GI: 400ns guard interval
+ */
+enum rate_info_flags {
+	RATE_INFO_FLAGS_MCS		= 1<<0,
+	RATE_INFO_FLAGS_40_MHZ_WIDTH	= 1<<1,
+	RATE_INFO_FLAGS_SHORT_GI	= 1<<2,
+};
+
+/**
+ * struct rate_info - bitrate information
+ *
+ * Information about a receiving or transmitting bitrate
+ *
+ * @flags: bitflag of flags from &enum rate_info_flags
+ * @mcs: mcs index if struct describes a 802.11n bitrate
+ * @legacy: bitrate in 100kbit/s for 802.11abg
+ */
+struct rate_info {
+	u8 flags;
+	u8 mcs;
+	u16 legacy;
 };
 
 /**
@@ -189,6 +237,10 @@ enum station_info_flags {
  * @llid: mesh local link id
  * @plid: mesh peer link id
  * @plink_state: mesh peer link state
+ * @signal: signal strength of last received packet in dBm
+ * @txrate: current unicast bitrate to this station
+ * @rx_packets: packets received from this station
+ * @tx_packets: packets transmitted to this station
  */
 struct station_info {
 	u32 filled;
@@ -198,6 +250,10 @@ struct station_info {
 	u16 llid;
 	u16 plid;
 	u8 plink_state;
+	s8 signal;
+	struct rate_info txrate;
+	u32 rx_packets;
+	u32 tx_packets;
 };
 
 /**
@@ -280,32 +336,63 @@ struct mpath_info {
  *	(0 = no, 1 = yes, -1 = do not change)
  * @use_short_slot_time: Whether the use of short slot time is allowed
  *	(0 = no, 1 = yes, -1 = do not change)
+ * @basic_rates: basic rates in IEEE 802.11 format
+ *	(or NULL for no change)
+ * @basic_rates_len: number of basic rates
  */
 struct bss_parameters {
 	int use_cts_prot;
 	int use_short_preamble;
 	int use_short_slot_time;
+	u8 *basic_rates;
+	u8 basic_rates_len;
 };
 
 /**
- * enum reg_set_by - Indicates who is trying to set the regulatory domain
- * @REGDOM_SET_BY_INIT: regulatory domain was set by initialization. We will be
- * 	using a static world regulatory domain by default.
- * @REGDOM_SET_BY_CORE: Core queried CRDA for a dynamic world regulatory domain.
- * @REGDOM_SET_BY_USER: User asked the wireless core to set the
- * 	regulatory domain.
- * @REGDOM_SET_BY_DRIVER: a wireless drivers has hinted to the wireless core
- *	it thinks its knows the regulatory domain we should be in.
- * @REGDOM_SET_BY_COUNTRY_IE: the wireless core has received an 802.11 country
- *	information element with regulatory information it thinks we
- *	should consider.
+ * enum environment_cap - Environment parsed from country IE
+ * @ENVIRON_ANY: indicates country IE applies to both indoor and
+ *	outdoor operation.
+ * @ENVIRON_INDOOR: indicates country IE applies only to indoor operation
+ * @ENVIRON_OUTDOOR: indicates country IE applies only to outdoor operation
  */
-enum reg_set_by {
-	REGDOM_SET_BY_INIT,
-	REGDOM_SET_BY_CORE,
-	REGDOM_SET_BY_USER,
-	REGDOM_SET_BY_DRIVER,
-	REGDOM_SET_BY_COUNTRY_IE,
+enum environment_cap {
+	ENVIRON_ANY,
+	ENVIRON_INDOOR,
+	ENVIRON_OUTDOOR,
+};
+
+/**
+ * struct regulatory_request - used to keep track of regulatory requests
+ *
+ * @wiphy_idx: this is set if this request's initiator is
+ * 	%REGDOM_SET_BY_COUNTRY_IE or %REGDOM_SET_BY_DRIVER. This
+ * 	can be used by the wireless core to deal with conflicts
+ * 	and potentially inform users of which devices specifically
+ * 	cased the conflicts.
+ * @initiator: indicates who sent this request, could be any of
+ * 	of those set in nl80211_reg_initiator (%NL80211_REGDOM_SET_BY_*)
+ * @alpha2: the ISO / IEC 3166 alpha2 country code of the requested
+ * 	regulatory domain. We have a few special codes:
+ * 	00 - World regulatory domain
+ * 	99 - built by driver but a specific alpha2 cannot be determined
+ * 	98 - result of an intersection between two regulatory domains
+ * @intersect: indicates whether the wireless core should intersect
+ * 	the requested regulatory domain with the presently set regulatory
+ * 	domain.
+ * @country_ie_checksum: checksum of the last processed and accepted
+ * 	country IE
+ * @country_ie_env: lets us know if the AP is telling us we are outdoor,
+ * 	indoor, or if it doesn't matter
+ * @list: used to insert into the reg_requests_list linked list
+ */
+struct regulatory_request {
+	int wiphy_idx;
+	enum nl80211_reg_initiator initiator;
+	char alpha2[2];
+	bool intersect;
+	u32 country_ie_checksum;
+	enum environment_cap country_ie_env;
+	struct list_head list;
 };
 
 struct ieee80211_freq_range {
@@ -331,25 +418,246 @@ struct ieee80211_regdomain {
 	struct ieee80211_reg_rule reg_rules[];
 };
 
-#define MHZ_TO_KHZ(freq) (freq * 1000)
-#define KHZ_TO_MHZ(freq) (freq / 1000)
-#define DBI_TO_MBI(gain) (gain * 100)
-#define MBI_TO_DBI(gain) (gain / 100)
-#define DBM_TO_MBM(gain) (gain * 100)
-#define MBM_TO_DBM(gain) (gain / 100)
+#define MHZ_TO_KHZ(freq) ((freq) * 1000)
+#define KHZ_TO_MHZ(freq) ((freq) / 1000)
+#define DBI_TO_MBI(gain) ((gain) * 100)
+#define MBI_TO_DBI(gain) ((gain) / 100)
+#define DBM_TO_MBM(gain) ((gain) * 100)
+#define MBM_TO_DBM(gain) ((gain) / 100)
 
 #define REG_RULE(start, end, bw, gain, eirp, reg_flags) { \
-	.freq_range.start_freq_khz = (start) * 1000, \
-	.freq_range.end_freq_khz = (end) * 1000, \
-	.freq_range.max_bandwidth_khz = (bw) * 1000, \
-	.power_rule.max_antenna_gain = (gain) * 100, \
-	.power_rule.max_eirp = (eirp) * 100, \
+	.freq_range.start_freq_khz = MHZ_TO_KHZ(start), \
+	.freq_range.end_freq_khz = MHZ_TO_KHZ(end), \
+	.freq_range.max_bandwidth_khz = MHZ_TO_KHZ(bw), \
+	.power_rule.max_antenna_gain = DBI_TO_MBI(gain), \
+	.power_rule.max_eirp = DBM_TO_MBM(eirp), \
 	.flags = reg_flags, \
 	}
 
+struct mesh_config {
+	/* Timeouts in ms */
+	/* Mesh plink management parameters */
+	u16 dot11MeshRetryTimeout;
+	u16 dot11MeshConfirmTimeout;
+	u16 dot11MeshHoldingTimeout;
+	u16 dot11MeshMaxPeerLinks;
+	u8  dot11MeshMaxRetries;
+	u8  dot11MeshTTL;
+	bool auto_open_plinks;
+	/* HWMP parameters */
+	u8  dot11MeshHWMPmaxPREQretries;
+	u32 path_refresh_time;
+	u16 min_discovery_timeout;
+	u32 dot11MeshHWMPactivePathTimeout;
+	u16 dot11MeshHWMPpreqMinInterval;
+	u16 dot11MeshHWMPnetDiameterTraversalTime;
+};
+
+/**
+ * struct ieee80211_txq_params - TX queue parameters
+ * @queue: TX queue identifier (NL80211_TXQ_Q_*)
+ * @txop: Maximum burst time in units of 32 usecs, 0 meaning disabled
+ * @cwmin: Minimum contention window [a value of the form 2^n-1 in the range
+ *	1..32767]
+ * @cwmax: Maximum contention window [a value of the form 2^n-1 in the range
+ *	1..32767]
+ * @aifs: Arbitration interframe space [0..255]
+ */
+struct ieee80211_txq_params {
+	enum nl80211_txq_q queue;
+	u16 txop;
+	u16 cwmin;
+	u16 cwmax;
+	u8 aifs;
+};
+
 /* from net/wireless.h */
 struct wiphy;
 
+/* from net/ieee80211.h */
+struct ieee80211_channel;
+
+/**
+ * struct cfg80211_ssid - SSID description
+ * @ssid: the SSID
+ * @ssid_len: length of the ssid
+ */
+struct cfg80211_ssid {
+	u8 ssid[IEEE80211_MAX_SSID_LEN];
+	u8 ssid_len;
+};
+
+/**
+ * struct cfg80211_scan_request - scan request description
+ *
+ * @ssids: SSIDs to scan for (active scan only)
+ * @n_ssids: number of SSIDs
+ * @channels: channels to scan on.
+ * @n_channels: number of channels for each band
+ * @ie: optional information element(s) to add into Probe Request or %NULL
+ * @ie_len: length of ie in octets
+ * @wiphy: the wiphy this was for
+ * @ifidx: the interface index
+ */
+struct cfg80211_scan_request {
+	struct cfg80211_ssid *ssids;
+	int n_ssids;
+	struct ieee80211_channel **channels;
+	u32 n_channels;
+	u8 *ie;
+	size_t ie_len;
+
+	/* internal */
+	struct wiphy *wiphy;
+	int ifidx;
+};
+
+/**
+ * enum cfg80211_signal_type - signal type
+ *
+ * @CFG80211_SIGNAL_TYPE_NONE: no signal strength information available
+ * @CFG80211_SIGNAL_TYPE_MBM: signal strength in mBm (100*dBm)
+ * @CFG80211_SIGNAL_TYPE_UNSPEC: signal strength, increasing from 0 through 100
+ */
+enum cfg80211_signal_type {
+	CFG80211_SIGNAL_TYPE_NONE,
+	CFG80211_SIGNAL_TYPE_MBM,
+	CFG80211_SIGNAL_TYPE_UNSPEC,
+};
+
+/**
+ * struct cfg80211_bss - BSS description
+ *
+ * This structure describes a BSS (which may also be a mesh network)
+ * for use in scan results and similar.
+ *
+ * @bssid: BSSID of the BSS
+ * @tsf: timestamp of last received update
+ * @beacon_interval: the beacon interval as from the frame
+ * @capability: the capability field in host byte order
+ * @information_elements: the information elements (Note that there
+ *	is no guarantee that these are well-formed!)
+ * @len_information_elements: total length of the information elements
+ * @signal: signal strength value (type depends on the wiphy's signal_type)
+ * @hold: BSS should not expire
+ * @free_priv: function pointer to free private data
+ * @priv: private area for driver use, has at least wiphy->bss_priv_size bytes
+ */
+struct cfg80211_bss {
+	struct ieee80211_channel *channel;
+
+	u8 bssid[ETH_ALEN];
+	u64 tsf;
+	u16 beacon_interval;
+	u16 capability;
+	u8 *information_elements;
+	size_t len_information_elements;
+
+	s32 signal;
+
+	void (*free_priv)(struct cfg80211_bss *bss);
+	u8 priv[0] __attribute__((__aligned__(sizeof(void *))));
+};
+
+/**
+ * struct cfg80211_auth_request - Authentication request data
+ *
+ * This structure provides information needed to complete IEEE 802.11
+ * authentication.
+ * NOTE: This structure will likely change when more code from mac80211 is
+ * moved into cfg80211 so that non-mac80211 drivers can benefit from it, too.
+ * Before using this in a driver that does not use mac80211, it would be better
+ * to check the status of that work and better yet, volunteer to work on it.
+ *
+ * @chan: The channel to use or %NULL if not specified (auto-select based on
+ *	scan results)
+ * @peer_addr: The address of the peer STA (AP BSSID in infrastructure case);
+ *	this field is required to be present; if the driver wants to help with
+ *	BSS selection, it should use (yet to be added) MLME event to allow user
+ *	space SME to be notified of roaming candidate, so that the SME can then
+ *	use the authentication request with the recommended BSSID and whatever
+ *	other data may be needed for authentication/association
+ * @ssid: SSID or %NULL if not yet available
+ * @ssid_len: Length of ssid in octets
+ * @auth_type: Authentication type (algorithm)
+ * @ie: Extra IEs to add to Authentication frame or %NULL
+ * @ie_len: Length of ie buffer in octets
+ */
+struct cfg80211_auth_request {
+	struct ieee80211_channel *chan;
+	u8 *peer_addr;
+	const u8 *ssid;
+	size_t ssid_len;
+	enum nl80211_auth_type auth_type;
+	const u8 *ie;
+	size_t ie_len;
+};
+
+/**
+ * struct cfg80211_assoc_request - (Re)Association request data
+ *
+ * This structure provides information needed to complete IEEE 802.11
+ * (re)association.
+ * NOTE: This structure will likely change when more code from mac80211 is
+ * moved into cfg80211 so that non-mac80211 drivers can benefit from it, too.
+ * Before using this in a driver that does not use mac80211, it would be better
+ * to check the status of that work and better yet, volunteer to work on it.
+ *
+ * @chan: The channel to use or %NULL if not specified (auto-select based on
+ *	scan results)
+ * @peer_addr: The address of the peer STA (AP BSSID); this field is required
+ *	to be present and the STA must be in State 2 (authenticated) with the
+ *	peer STA
+ * @ssid: SSID
+ * @ssid_len: Length of ssid in octets
+ * @ie: Extra IEs to add to (Re)Association Request frame or %NULL
+ * @ie_len: Length of ie buffer in octets
+ */
+struct cfg80211_assoc_request {
+	struct ieee80211_channel *chan;
+	u8 *peer_addr;
+	const u8 *ssid;
+	size_t ssid_len;
+	const u8 *ie;
+	size_t ie_len;
+};
+
+/**
+ * struct cfg80211_deauth_request - Deauthentication request data
+ *
+ * This structure provides information needed to complete IEEE 802.11
+ * deauthentication.
+ *
+ * @peer_addr: The address of the peer STA (AP BSSID); this field is required
+ *	to be present and the STA must be authenticated with the peer STA
+ * @ie: Extra IEs to add to Deauthentication frame or %NULL
+ * @ie_len: Length of ie buffer in octets
+ */
+struct cfg80211_deauth_request {
+	u8 *peer_addr;
+	u16 reason_code;
+	const u8 *ie;
+	size_t ie_len;
+};
+
+/**
+ * struct cfg80211_disassoc_request - Disassociation request data
+ *
+ * This structure provides information needed to complete IEEE 802.11
+ * disassocation.
+ *
+ * @peer_addr: The address of the peer STA (AP BSSID); this field is required
+ *	to be present and the STA must be associated with the peer STA
+ * @ie: Extra IEs to add to Disassociation frame or %NULL
+ * @ie_len: Length of ie buffer in octets
+ */
+struct cfg80211_disassoc_request {
+	u8 *peer_addr;
+	u16 reason_code;
+	const u8 *ie;
+	size_t ie_len;
+};
+
 /**
  * struct cfg80211_ops - backend description for wireless configuration
  *
@@ -363,6 +671,9 @@ struct wiphy;
  * wireless extensions but this is subject to reevaluation as soon as this
  * code is used more widely and we have a first user without wext.
  *
+ * @suspend: wiphy device needs to be suspended
+ * @resume: wiphy device needs to be resumed
+ *
  * @add_virtual_intf: create a new virtual interface with the given name,
  *	must set the struct wireless_dev's iftype.
  *
@@ -384,6 +695,8 @@ struct wiphy;
  *
  * @set_default_key: set the default key on an interface
  *
+ * @set_default_mgmt_key: set the default management frame key on an interface
+ *
  * @add_beacon: Add a beacon with given parameters, @head, @interval
  *	and @dtim_period will be valid, @tail is optional.
  * @set_beacon: Change the beacon parameters for an access point mode
@@ -397,11 +710,34 @@ struct wiphy;
  *
  * @change_station: Modify a given station.
  *
+ * @get_mesh_params: Put the current mesh parameters into *params
+ *
+ * @set_mesh_params: Set mesh parameters.
+ *	The mask is a bitfield which tells us which parameters to
+ *	set, and which to leave alone.
+ *
  * @set_mesh_cfg: set mesh parameters (by now, just mesh id)
  *
  * @change_bss: Modify parameters for a given BSS.
+ *
+ * @set_txq_params: Set TX queue parameters
+ *
+ * @set_channel: Set channel
+ *
+ * @scan: Request to do a scan. If returning zero, the scan request is given
+ *	the driver, and will be valid until passed to cfg80211_scan_done().
+ *	For scan results, call cfg80211_inform_bss(); you can call this outside
+ *	the scan/scan_done bracket too.
+ *
+ * @auth: Request to authenticate with the specified peer
+ * @assoc: Request to (re)associate with the specified peer
+ * @deauth: Request to deauthenticate from the specified peer
+ * @disassoc: Request to disassociate from the specified peer
  */
 struct cfg80211_ops {
+	int	(*suspend)(struct wiphy *wiphy);
+	int	(*resume)(struct wiphy *wiphy);
+
 	int	(*add_virtual_intf)(struct wiphy *wiphy, char *name,
 				    enum nl80211_iftype type, u32 *flags,
 				    struct vif_params *params);
@@ -421,6 +757,9 @@ struct cfg80211_ops {
 	int	(*set_default_key)(struct wiphy *wiphy,
 				   struct net_device *netdev,
 				   u8 key_index);
+	int	(*set_default_mgmt_key)(struct wiphy *wiphy,
+					struct net_device *netdev,
+					u8 key_index);
 
 	int	(*add_beacon)(struct wiphy *wiphy, struct net_device *dev,
 			      struct beacon_parameters *info);
@@ -452,9 +791,171 @@ struct cfg80211_ops {
 	int	(*dump_mpath)(struct wiphy *wiphy, struct net_device *dev,
 			       int idx, u8 *dst, u8 *next_hop,
 			       struct mpath_info *pinfo);
-
+	int	(*get_mesh_params)(struct wiphy *wiphy,
+				struct net_device *dev,
+				struct mesh_config *conf);
+	int	(*set_mesh_params)(struct wiphy *wiphy,
+				struct net_device *dev,
+				const struct mesh_config *nconf, u32 mask);
 	int	(*change_bss)(struct wiphy *wiphy, struct net_device *dev,
 			      struct bss_parameters *params);
+
+	int	(*set_txq_params)(struct wiphy *wiphy,
+				  struct ieee80211_txq_params *params);
+
+	int	(*set_channel)(struct wiphy *wiphy,
+			       struct ieee80211_channel *chan,
+			       enum nl80211_channel_type channel_type);
+
+	int	(*scan)(struct wiphy *wiphy, struct net_device *dev,
+			struct cfg80211_scan_request *request);
+
+	int	(*auth)(struct wiphy *wiphy, struct net_device *dev,
+			struct cfg80211_auth_request *req);
+	int	(*assoc)(struct wiphy *wiphy, struct net_device *dev,
+			 struct cfg80211_assoc_request *req);
+	int	(*deauth)(struct wiphy *wiphy, struct net_device *dev,
+			  struct cfg80211_deauth_request *req);
+	int	(*disassoc)(struct wiphy *wiphy, struct net_device *dev,
+			    struct cfg80211_disassoc_request *req);
 };
 
+/* temporary wext handlers */
+int cfg80211_wext_giwname(struct net_device *dev,
+			  struct iw_request_info *info,
+			  char *name, char *extra);
+int cfg80211_wext_siwmode(struct net_device *dev, struct iw_request_info *info,
+			  u32 *mode, char *extra);
+int cfg80211_wext_giwmode(struct net_device *dev, struct iw_request_info *info,
+			  u32 *mode, char *extra);
+int cfg80211_wext_siwscan(struct net_device *dev,
+			  struct iw_request_info *info,
+			  union iwreq_data *wrqu, char *extra);
+int cfg80211_wext_giwscan(struct net_device *dev,
+			  struct iw_request_info *info,
+			  struct iw_point *data, char *extra);
+int cfg80211_wext_giwrange(struct net_device *dev,
+			   struct iw_request_info *info,
+			   struct iw_point *data, char *extra);
+
+/**
+ * cfg80211_scan_done - notify that scan finished
+ *
+ * @request: the corresponding scan request
+ * @aborted: set to true if the scan was aborted for any reason,
+ *	userspace will be notified of that
+ */
+void cfg80211_scan_done(struct cfg80211_scan_request *request, bool aborted);
+
+/**
+ * cfg80211_inform_bss - inform cfg80211 of a new BSS
+ *
+ * @wiphy: the wiphy reporting the BSS
+ * @bss: the found BSS
+ * @signal: the signal strength, type depends on the wiphy's signal_type
+ * @gfp: context flags
+ *
+ * This informs cfg80211 that BSS information was found and
+ * the BSS should be updated/added.
+ */
+struct cfg80211_bss*
+cfg80211_inform_bss_frame(struct wiphy *wiphy,
+			  struct ieee80211_channel *channel,
+			  struct ieee80211_mgmt *mgmt, size_t len,
+			  s32 signal, gfp_t gfp);
+
+struct cfg80211_bss *cfg80211_get_bss(struct wiphy *wiphy,
+				      struct ieee80211_channel *channel,
+				      const u8 *bssid,
+				      const u8 *ssid, size_t ssid_len,
+				      u16 capa_mask, u16 capa_val);
+static inline struct cfg80211_bss *
+cfg80211_get_ibss(struct wiphy *wiphy,
+		  struct ieee80211_channel *channel,
+		  const u8 *ssid, size_t ssid_len)
+{
+	return cfg80211_get_bss(wiphy, channel, NULL, ssid, ssid_len,
+				WLAN_CAPABILITY_IBSS, WLAN_CAPABILITY_IBSS);
+}
+
+struct cfg80211_bss *cfg80211_get_mesh(struct wiphy *wiphy,
+				       struct ieee80211_channel *channel,
+				       const u8 *meshid, size_t meshidlen,
+				       const u8 *meshcfg);
+void cfg80211_put_bss(struct cfg80211_bss *bss);
+/**
+ * cfg80211_unlink_bss - unlink BSS from internal data structures
+ * @wiphy: the wiphy
+ * @bss: the bss to remove
+ *
+ * This function removes the given BSS from the internal data structures
+ * thereby making it no longer show up in scan results etc. Use this
+ * function when you detect a BSS is gone. Normally BSSes will also time
+ * out, so it is not necessary to use this function at all.
+ */
+void cfg80211_unlink_bss(struct wiphy *wiphy, struct cfg80211_bss *bss);
+
+/**
+ * cfg80211_send_rx_auth - notification of processed authentication
+ * @dev: network device
+ * @buf: authentication frame (header + body)
+ * @len: length of the frame data
+ *
+ * This function is called whenever an authentication has been processed in
+ * station mode.
+ */
+void cfg80211_send_rx_auth(struct net_device *dev, const u8 *buf, size_t len);
+
+/**
+ * cfg80211_send_rx_assoc - notification of processed association
+ * @dev: network device
+ * @buf: (re)association response frame (header + body)
+ * @len: length of the frame data
+ *
+ * This function is called whenever a (re)association response has been
+ * processed in station mode.
+ */
+void cfg80211_send_rx_assoc(struct net_device *dev, const u8 *buf, size_t len);
+
+/**
+ * cfg80211_send_rx_deauth - notification of processed deauthentication
+ * @dev: network device
+ * @buf: deauthentication frame (header + body)
+ * @len: length of the frame data
+ *
+ * This function is called whenever deauthentication has been processed in
+ * station mode.
+ */
+void cfg80211_send_rx_deauth(struct net_device *dev, const u8 *buf,
+			     size_t len);
+
+/**
+ * cfg80211_send_rx_disassoc - notification of processed disassociation
+ * @dev: network device
+ * @buf: disassociation response frame (header + body)
+ * @len: length of the frame data
+ *
+ * This function is called whenever disassociation has been processed in
+ * station mode.
+ */
+void cfg80211_send_rx_disassoc(struct net_device *dev, const u8 *buf,
+			       size_t len);
+
+/**
+ * cfg80211_hold_bss - exclude bss from expiration
+ * @bss: bss which should not expire
+ *
+ * In a case when the BSS is not updated but it shouldn't expire this
+ * function can be used to mark the BSS to be excluded from expiration.
+ */
+void cfg80211_hold_bss(struct cfg80211_bss *bss);
+
+/**
+ * cfg80211_unhold_bss - remove expiration exception from the BSS
+ * @bss: bss which can expire again
+ *
+ * This function marks the BSS to be expirable again.
+ */
+void cfg80211_unhold_bss(struct cfg80211_bss *bss);
+
 #endif /* __NET_CFG80211_H */