X-Git-Url: http://ftp.safe.ca/?a=blobdiff_plain;f=drivers%2Fw1%2FKconfig;h=9adbb4f904799c0d0c73a2fe80e7bc2c6da3b643;hb=77bdd9ee1e1d94fa853c354dcde881ddc5d277a5;hp=4f120796273ee033b2cb694c2664b594833fd28a;hpb=7785925dd8e0d2f389d4a9168f1683c6b249a552;p=safe%2Fjmp%2Flinux-2.6

diff --git a/drivers/w1/Kconfig b/drivers/w1/Kconfig
index 4f12079..9adbb4f 100644
--- a/drivers/w1/Kconfig
+++ b/drivers/w1/Kconfig
@@ -1,9 +1,8 @@
-menu "Dallas's 1-wire bus"
-
-config W1
+menuconfig W1
 	tristate "Dallas's 1-wire support"
+	depends on HAS_IOMEM
 	---help---
-	  Dallas's 1-wire bus is usefull to connect slow 1-pin devices
+	  Dallas' 1-wire bus is useful to connect slow 1-pin devices
 	  such as iButtons and thermal sensors.
 
 	  If you want W1 support, you should say Y here.
@@ -11,47 +10,22 @@ config W1
 	  This W1 support can also be built as a module.  If so, the module
 	  will be called wire.ko.
 
-config W1_MATROX
-	tristate "Matrox G400 transport layer for 1-wire"
-	depends on W1 && PCI
-	help
-	  Say Y here if you want to communicate with your 1-wire devices
-	  using Matrox's G400 GPIO pins.
-
-	  This support is also available as a module.  If so, the module
-	  will be called matrox_w1.ko.
-
-config W1_DS9490
-	tristate "DS9490R transport layer driver"
-	depends on W1 && USB
-	help
-	  Say Y here if you want to have a driver for DS9490R UWB <-> W1 bridge.
-
-	  This support is also available as a module.  If so, the module
-	  will be called ds9490r.ko.
-
-config W1_DS9490R_BRIDGE
-	tristate "DS9490R USB <-> W1 transport layer for 1-wire"
-	depends on W1_DS9490
-	help
-	  Say Y here if you want to communicate with your 1-wire devices
-	  using DS9490R USB bridge.
-
-	  This support is also available as a module.  If so, the module
-	  will be called ds_w1_bridge.ko.
-
-config W1_THERM
-	tristate "Thermal family implementation"
-	depends on W1
-	help
-	  Say Y here if you want to connect 1-wire thermal sensors to you
-	  wire.
-
-config W1_SMEM
-	tristate "Simple 64bit memory family implementation"
-	depends on W1
-	help
-	  Say Y here if you want to connect 1-wire
-	  simple 64bit memory rom(ds2401/ds2411/ds1990*) to you wire.
-
-endmenu
+if W1
+
+config W1_CON
+	depends on CONNECTOR
+	bool "Userspace communication over connector"
+	default y
+	--- help ---
+	  This allows to communicate with userspace using connector. For more
+	  information see <file:Documentation/connector/connector.txt>.
+	  There are three types of messages between w1 core and userspace:
+	  1. Events. They are generated each time new master or slave device found
+		either due to automatic or requested search.
+	  2. Userspace commands. Includes read/write and search/alarm search commands.
+	  3. Replies to userspace commands.
+
+source drivers/w1/masters/Kconfig
+source drivers/w1/slaves/Kconfig
+
+endif # W1