X-Git-Url: http://ftp.safe.ca/?a=blobdiff_plain;f=drivers%2Fusb%2Fnet%2Fusbnet.c;h=79b5474fe2343593b41f1ef61d218fe42d159f65;hb=c4028958b6ecad064b1a6303a6a5906d4fe48d73;hp=3c6eef4168e5ba9cc8746404a1177fcc219ff714;hpb=b375a0495fd622037560c73c05f23ae6f127bb0c;p=safe%2Fjmp%2Flinux-2.6 diff --git a/drivers/usb/net/usbnet.c b/drivers/usb/net/usbnet.c index 3c6eef4..79b5474 100644 --- a/drivers/usb/net/usbnet.c +++ b/drivers/usb/net/usbnet.c @@ -1,10 +1,7 @@ /* - * USB Networking Links - * Copyright (C) 2000-2005 by David Brownell - * Copyright (C) 2002 Pavel Machek + * USB Network driver infrastructure + * Copyright (C) 2000-2005 by David Brownell * Copyright (C) 2003-2005 David Hollis - * Copyright (C) 2005 Phil Chang - * Copyright (c) 2002-2003 TiVo Inc. * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by @@ -23,122 +20,32 @@ /* * This is a generic "USB networking" framework that works with several - * kinds of full and high speed networking devices: - * - * + USB host-to-host "network cables", used for IP-over-USB links. - * These are often used for Laplink style connectivity products. - * - AnchorChip 2720 - * - Belkin, eTEK (interops with Win32 drivers) - * - GeneSys GL620USB-A - * - NetChip 1080 (interoperates with NetChip Win32 drivers) - * - Prolific PL-2301/2302 (replaces "plusb" driver) - * - KC Technology KC2190 - * - * + Smart USB devices can support such links directly, using Internet - * standard protocols instead of proprietary host-to-device links. - * - Linux PDAs like iPaq, Yopy, and Zaurus - * - The BLOB boot loader (for diskless booting) - * - Linux "gadgets", perhaps using PXA-2xx or Net2280 controllers - * - Devices using EPSON's sample USB firmware - * - CDC-Ethernet class devices, such as many cable modems - * - * + Adapters to networks such as Ethernet. - * - AX8817X based USB 2.0 products - * - * Links to these devices can be bridged using Linux Ethernet bridging. - * With minor exceptions, these all use similar USB framing for network - * traffic, but need different protocols for control traffic. - * - * USB devices can implement their side of this protocol at the cost - * of two bulk endpoints; it's not restricted to "cable" applications. - * See the SA1110, Zaurus, or EPSON device/client support in this driver; - * slave/target drivers such as "usb-eth" (on most SA-1100 PDAs) or - * "g_ether" (in the Linux "gadget" framework) implement that behavior - * within devices. - * - * - * CHANGELOG: - * - * 13-sep-2000 experimental, new - * 10-oct-2000 usb_device_id table created. - * 28-oct-2000 misc fixes; mostly, discard more TTL-mangled rx packets. - * 01-nov-2000 usb_device_id table and probing api update by - * Adam J. Richter . - * 18-dec-2000 (db) tx watchdog, "net1080" renaming to "usbnet", device_info - * and prolific support, isolate net1080-specific bits, cleanup. - * fix unlink_urbs oops in D3 PM resume code path. - * - * 02-feb-2001 (db) fix tx skb sharing, packet length, match_flags, ... - * 08-feb-2001 stubbed in "linuxdev", maybe the SA-1100 folk can use it; - * AnchorChips 2720 support (from spec) for testing; - * fix bit-ordering problem with ethernet multicast addr - * 19-feb-2001 Support for clearing halt conditions. SA1100 UDC support - * updates. Oleg Drokin (green@iXcelerator.com) - * 25-mar-2001 More SA-1100 updates, including workaround for ip problem - * expecting cleared skb->cb and framing change to match latest - * handhelds.org version (Oleg). Enable device IDs from the - * Win32 Belkin driver; other cleanups (db). - * 16-jul-2001 Bugfixes for uhci oops-on-unplug, Belkin support, various - * cleanups for problems not yet seen in the field. (db) - * 17-oct-2001 Handle "Advance USBNET" product, like Belkin/eTEK devices, - * from Ioannis Mavroukakis ; - * rx unlinks somehow weren't async; minor cleanup. - * 03-nov-2001 Merged GeneSys driver; original code from Jiun-Jie Huang - * , updated by Stanislav Brabec - * . Made framing options (NetChip/GeneSys) - * tie mostly to (sub)driver info. Workaround some PL-2302 - * chips that seem to reject SET_INTERFACE requests. - * - * 06-apr-2002 Added ethtool support, based on a patch from Brad Hards. - * Level of diagnostics is more configurable; they use device - * location (usb_device->devpath) instead of address (2.5). - * For tx_fixup, memflags can't be NOIO. - * 07-may-2002 Generalize/cleanup keventd support, handling rx stalls (mostly - * for USB 2.0 TTs) and memory shortages (potential) too. (db) - * Use "locally assigned" IEEE802 address space. (Brad Hards) - * 18-oct-2002 Support for Zaurus (Pavel Machek), related cleanup (db). - * 14-dec-2002 Remove Zaurus-private crc32 code (Pavel); 2.5 oops fix, - * cleanups and stubbed PXA-250 support (db), fix for framing - * issues on Z, net1080, and gl620a (Toby Milne) - * - * 31-mar-2003 Use endpoint descriptors: high speed support, simpler sa1100 - * vs pxa25x, and CDC Ethernet. Throttle down log floods on - * disconnect; other cleanups. (db) Flush net1080 fifos - * after several sequential framing errors. (Johannes Erdfelt) - * 22-aug-2003 AX8817X support (Dave Hollis). - * 14-jun-2004 Trivial patch for AX8817X based Buffalo LUA-U2-KTX in Japan - * (Neil Bortnak) - * 03-nov-2004 Trivial patch for KC2190 (KC-190) chip. (Jonathan McDowell) - * - * 01-feb-2005 AX88772 support (Phil Chang & Dave Hollis) - *-------------------------------------------------------------------------*/ + * kinds of full and high speed networking devices: host-to-host cables, + * smart usb peripherals, and actual Ethernet adapters. + * + * These devices usually differ in terms of control protocols (if they + * even have one!) and sometimes they define new framing to wrap or batch + * Ethernet packets. Otherwise, they talk to USB pretty much the same, + * so interface (un)binding, endpoint I/O queues, fault handling, and other + * issues can usefully be addressed by this framework. + */ // #define DEBUG // error path messages, extra info // #define VERBOSE // more; success messages -#include -#ifdef CONFIG_USB_DEBUG -# define DEBUG -#endif #include -#include #include #include #include #include -#include #include #include #include -#include -#include #include -#include -#include -#include -#include -#define DRIVER_VERSION "03-Nov-2004" +#include "usbnet.h" + +#define DRIVER_VERSION "22-Aug-2005" /*-------------------------------------------------------------------------*/ @@ -149,14 +56,16 @@ * One maximum size Ethernet packet takes twenty four of them. * For high speed, each frame comfortably fits almost 36 max size * Ethernet packets (so queues should be bigger). + * + * REVISIT qlens should be members of 'struct usbnet'; the goal is to + * let the USB host controller be busy for 5msec or more before an irq + * is required, under load. Jumbograms change the equation. */ -#define RX_QLEN(dev) (((dev)->udev->speed == USB_SPEED_HIGH) ? 60 : 4) -#define TX_QLEN(dev) (((dev)->udev->speed == USB_SPEED_HIGH) ? 60 : 4) - -// packets are always ethernet inside -// ... except they can be bigger (limit of 64K with NetChip framing) -#define MIN_PACKET sizeof(struct ethhdr) -#define MAX_PACKET 32768 +#define RX_MAX_QUEUE_MEMORY (60 * 1518) +#define RX_QLEN(dev) (((dev)->udev->speed == USB_SPEED_HIGH) ? \ + (RX_MAX_QUEUE_MEMORY/(dev)->rx_urb_size) : 4) +#define TX_QLEN(dev) (((dev)->udev->speed == USB_SPEED_HIGH) ? \ + (RX_MAX_QUEUE_MEMORY/(dev)->hard_mtu) : 4) // reawaken network queue this soon after stopping; else watchdog barks #define TX_TIMEOUT_JIFFIES (5*HZ) @@ -165,9 +74,6 @@ // us (it polls at HZ/4 usually) before we report too many false errors. #define THROTTLE_JIFFIES (HZ/8) -// for vendor-specific control operations -#define CONTROL_TIMEOUT_MS 500 - // between wakeups #define UNLINK_TIMEOUT_MS 3 @@ -176,109 +82,6 @@ // randomly generated ethernet address static u8 node_id [ETH_ALEN]; -// state we keep for each device we handle -struct usbnet { - // housekeeping - struct usb_device *udev; - struct driver_info *driver_info; - wait_queue_head_t *wait; - - // i/o info: pipes etc - unsigned in, out; - struct usb_host_endpoint *status; - unsigned maxpacket; - struct timer_list delay; - - // protocol/interface state - struct net_device *net; - struct net_device_stats stats; - int msg_enable; - unsigned long data [5]; - - struct mii_if_info mii; - - // various kinds of pending driver work - struct sk_buff_head rxq; - struct sk_buff_head txq; - struct sk_buff_head done; - struct urb *interrupt; - struct tasklet_struct bh; - - struct work_struct kevent; - unsigned long flags; -# define EVENT_TX_HALT 0 -# define EVENT_RX_HALT 1 -# define EVENT_RX_MEMORY 2 -# define EVENT_STS_SPLIT 3 -# define EVENT_LINK_RESET 4 -}; - -// device-specific info used by the driver -struct driver_info { - char *description; - - int flags; -/* framing is CDC Ethernet, not writing ZLPs (hw issues), or optionally: */ -#define FLAG_FRAMING_NC 0x0001 /* guard against device dropouts */ -#define FLAG_FRAMING_GL 0x0002 /* genelink batches packets */ -#define FLAG_FRAMING_Z 0x0004 /* zaurus adds a trailer */ -#define FLAG_FRAMING_RN 0x0008 /* RNDIS batches, plus huge header */ - -#define FLAG_NO_SETINT 0x0010 /* device can't set_interface() */ -#define FLAG_ETHER 0x0020 /* maybe use "eth%d" names */ - -#define FLAG_FRAMING_AX 0x0040 /* AX88772/178 packets */ - - /* init device ... can sleep, or cause probe() failure */ - int (*bind)(struct usbnet *, struct usb_interface *); - - /* cleanup device ... can sleep, but can't fail */ - void (*unbind)(struct usbnet *, struct usb_interface *); - - /* reset device ... can sleep */ - int (*reset)(struct usbnet *); - - /* see if peer is connected ... can sleep */ - int (*check_connect)(struct usbnet *); - - /* for status polling */ - void (*status)(struct usbnet *, struct urb *); - - /* link reset handling, called from defer_kevent */ - int (*link_reset)(struct usbnet *); - - /* fixup rx packet (strip framing) */ - int (*rx_fixup)(struct usbnet *dev, struct sk_buff *skb); - - /* fixup tx packet (add framing) */ - struct sk_buff *(*tx_fixup)(struct usbnet *dev, - struct sk_buff *skb, unsigned flags); - - // FIXME -- also an interrupt mechanism - // useful for at least PL2301/2302 and GL620USB-A - // and CDC use them to report 'is it connected' changes - - /* for new devices, use the descriptor-reading code instead */ - int in; /* rx endpoint */ - int out; /* tx endpoint */ - - unsigned long data; /* Misc driver specific data */ -}; - -// we record the state for each of our queued skbs -enum skb_state { - illegal = 0, - tx_start, tx_done, - rx_start, rx_done, rx_cleanup -}; - -struct skb_data { // skb->cb is one of these - struct urb *urb; - struct usbnet *dev; - enum skb_state state; - size_t length; -}; - static const char driver_name [] = "usbnet"; /* use ethtool to change the level for any given device */ @@ -286,39 +89,10 @@ static int msg_level = -1; module_param (msg_level, int, 0); MODULE_PARM_DESC (msg_level, "Override default message level"); - -#ifdef DEBUG -#define devdbg(usbnet, fmt, arg...) \ - printk(KERN_DEBUG "%s: " fmt "\n" , (usbnet)->net->name , ## arg) -#else -#define devdbg(usbnet, fmt, arg...) do {} while(0) -#endif - -#define deverr(usbnet, fmt, arg...) \ - printk(KERN_ERR "%s: " fmt "\n" , (usbnet)->net->name , ## arg) -#define devwarn(usbnet, fmt, arg...) \ - printk(KERN_WARNING "%s: " fmt "\n" , (usbnet)->net->name , ## arg) - -#define devinfo(usbnet, fmt, arg...) \ - printk(KERN_INFO "%s: " fmt "\n" , (usbnet)->net->name , ## arg); \ - /*-------------------------------------------------------------------------*/ -static void usbnet_get_drvinfo (struct net_device *, struct ethtool_drvinfo *); -static u32 usbnet_get_link (struct net_device *); -static u32 usbnet_get_msglevel (struct net_device *); -static void usbnet_set_msglevel (struct net_device *, u32); -static void defer_kevent (struct usbnet *, int); - -/* mostly for PDA style devices, which are always connected if present */ -static int always_connected (struct usbnet *dev) -{ - return 0; -} - /* handles CDC Ethernet and many other network "bulk data" interfaces */ -static int -get_endpoints (struct usbnet *dev, struct usb_interface *intf) +int usbnet_get_endpoints(struct usbnet *dev, struct usb_interface *intf) { int tmp; struct usb_host_interface *alt = NULL; @@ -355,2508 +129,95 @@ get_endpoints (struct usbnet *dev, struct usb_interface *intf) if (!intr && !in) in = e; else if (intr && !status) - status = e; - } else { - if (!out) - out = e; - } - } - if (in && out) - break; - } - if (!alt || !in || !out) - return -EINVAL; - - if (alt->desc.bAlternateSetting != 0 - || !(dev->driver_info->flags & FLAG_NO_SETINT)) { - tmp = usb_set_interface (dev->udev, alt->desc.bInterfaceNumber, - alt->desc.bAlternateSetting); - if (tmp < 0) - return tmp; - } - - dev->in = usb_rcvbulkpipe (dev->udev, - in->desc.bEndpointAddress & USB_ENDPOINT_NUMBER_MASK); - dev->out = usb_sndbulkpipe (dev->udev, - out->desc.bEndpointAddress & USB_ENDPOINT_NUMBER_MASK); - dev->status = status; - return 0; -} - -static void intr_complete (struct urb *urb, struct pt_regs *regs); - -static int init_status (struct usbnet *dev, struct usb_interface *intf) -{ - char *buf = NULL; - unsigned pipe = 0; - unsigned maxp; - unsigned period; - - if (!dev->driver_info->status) - return 0; - - pipe = usb_rcvintpipe (dev->udev, - dev->status->desc.bEndpointAddress - & USB_ENDPOINT_NUMBER_MASK); - maxp = usb_maxpacket (dev->udev, pipe, 0); - - /* avoid 1 msec chatter: min 8 msec poll rate */ - period = max ((int) dev->status->desc.bInterval, - (dev->udev->speed == USB_SPEED_HIGH) ? 7 : 3); - - buf = kmalloc (maxp, SLAB_KERNEL); - if (buf) { - dev->interrupt = usb_alloc_urb (0, SLAB_KERNEL); - if (!dev->interrupt) { - kfree (buf); - return -ENOMEM; - } else { - usb_fill_int_urb(dev->interrupt, dev->udev, pipe, - buf, maxp, intr_complete, dev, period); - dev_dbg(&intf->dev, - "status ep%din, %d bytes period %d\n", - usb_pipeendpoint(pipe), maxp, period); - } - } - return 0; -} - -static void skb_return (struct usbnet *dev, struct sk_buff *skb) -{ - int status; - - skb->dev = dev->net; - skb->protocol = eth_type_trans (skb, dev->net); - dev->stats.rx_packets++; - dev->stats.rx_bytes += skb->len; - - if (netif_msg_rx_status (dev)) - devdbg (dev, "< rx, len %zu, type 0x%x", - skb->len + sizeof (struct ethhdr), skb->protocol); - memset (skb->cb, 0, sizeof (struct skb_data)); - status = netif_rx (skb); - if (status != NET_RX_SUCCESS && netif_msg_rx_err (dev)) - devdbg (dev, "netif_rx status %d", status); -} - - -#ifdef CONFIG_USB_ALI_M5632 -#define HAVE_HARDWARE - -/*------------------------------------------------------------------------- - * - * ALi M5632 driver ... does high speed - * - *-------------------------------------------------------------------------*/ - -static const struct driver_info ali_m5632_info = { - .description = "ALi M5632", -}; - - -#endif - - -#ifdef CONFIG_USB_AN2720 -#define HAVE_HARDWARE - -/*------------------------------------------------------------------------- - * - * AnchorChips 2720 driver ... http://www.cypress.com - * - * This doesn't seem to have a way to detect whether the peer is - * connected, or need any reset handshaking. It's got pretty big - * internal buffers (handles most of a frame's worth of data). - * Chip data sheets don't describe any vendor control messages. - * - *-------------------------------------------------------------------------*/ - -static const struct driver_info an2720_info = { - .description = "AnchorChips/Cypress 2720", - // no reset available! - // no check_connect available! - - .in = 2, .out = 2, // direction distinguishes these -}; - -#endif /* CONFIG_USB_AN2720 */ - - -#ifdef CONFIG_USB_AX8817X -/* ASIX AX8817X based USB 2.0 Ethernet Devices */ - -#define HAVE_HARDWARE -#define NEED_MII - -#include - -#define AX_CMD_SET_SW_MII 0x06 -#define AX_CMD_READ_MII_REG 0x07 -#define AX_CMD_WRITE_MII_REG 0x08 -#define AX_CMD_SET_HW_MII 0x0a -#define AX_CMD_READ_EEPROM 0x0b -#define AX_CMD_WRITE_EEPROM 0x0c -#define AX_CMD_WRITE_ENABLE 0x0d -#define AX_CMD_WRITE_DISABLE 0x0e -#define AX_CMD_WRITE_RX_CTL 0x10 -#define AX_CMD_READ_IPG012 0x11 -#define AX_CMD_WRITE_IPG0 0x12 -#define AX_CMD_WRITE_IPG1 0x13 -#define AX_CMD_WRITE_IPG2 0x14 -#define AX_CMD_WRITE_MULTI_FILTER 0x16 -#define AX_CMD_READ_NODE_ID 0x17 -#define AX_CMD_READ_PHY_ID 0x19 -#define AX_CMD_READ_MEDIUM_STATUS 0x1a -#define AX_CMD_WRITE_MEDIUM_MODE 0x1b -#define AX_CMD_READ_MONITOR_MODE 0x1c -#define AX_CMD_WRITE_MONITOR_MODE 0x1d -#define AX_CMD_WRITE_GPIOS 0x1f -#define AX_CMD_SW_RESET 0x20 -#define AX_CMD_SW_PHY_STATUS 0x21 -#define AX_CMD_SW_PHY_SELECT 0x22 -#define AX88772_CMD_READ_NODE_ID 0x13 - -#define AX_MONITOR_MODE 0x01 -#define AX_MONITOR_LINK 0x02 -#define AX_MONITOR_MAGIC 0x04 -#define AX_MONITOR_HSFS 0x10 - -/* AX88172 Medium Status Register values */ -#define AX_MEDIUM_FULL_DUPLEX 0x02 -#define AX_MEDIUM_TX_ABORT_ALLOW 0x04 -#define AX_MEDIUM_FLOW_CONTROL_EN 0x10 - -#define AX_MCAST_FILTER_SIZE 8 -#define AX_MAX_MCAST 64 - -#define AX_EEPROM_LEN 0x40 - -#define AX_SWRESET_CLEAR 0x00 -#define AX_SWRESET_RR 0x01 -#define AX_SWRESET_RT 0x02 -#define AX_SWRESET_PRTE 0x04 -#define AX_SWRESET_PRL 0x08 -#define AX_SWRESET_BZ 0x10 -#define AX_SWRESET_IPRL 0x20 -#define AX_SWRESET_IPPD 0x40 - -#define AX88772_IPG0_DEFAULT 0x15 -#define AX88772_IPG1_DEFAULT 0x0c -#define AX88772_IPG2_DEFAULT 0x12 - -#define AX88772_MEDIUM_FULL_DUPLEX 0x0002 -#define AX88772_MEDIUM_RESERVED 0x0004 -#define AX88772_MEDIUM_RX_FC_ENABLE 0x0010 -#define AX88772_MEDIUM_TX_FC_ENABLE 0x0020 -#define AX88772_MEDIUM_PAUSE_FORMAT 0x0080 -#define AX88772_MEDIUM_RX_ENABLE 0x0100 -#define AX88772_MEDIUM_100MB 0x0200 -#define AX88772_MEDIUM_DEFAULT \ - (AX88772_MEDIUM_FULL_DUPLEX | AX88772_MEDIUM_RX_FC_ENABLE | \ - AX88772_MEDIUM_TX_FC_ENABLE | AX88772_MEDIUM_100MB | \ - AX88772_MEDIUM_RESERVED | AX88772_MEDIUM_RX_ENABLE ) - -#define AX_EEPROM_MAGIC 0xdeadbeef - -/* This structure cannot exceed sizeof(unsigned long [5]) AKA 20 bytes */ -struct ax8817x_data { - u8 multi_filter[AX_MCAST_FILTER_SIZE]; -}; - -struct ax88172_int_data { - u16 res1; - u8 link; - u16 res2; - u8 status; - u16 res3; -} __attribute__ ((packed)); - -static int ax8817x_read_cmd(struct usbnet *dev, u8 cmd, u16 value, u16 index, - u16 size, void *data) -{ - return usb_control_msg( - dev->udev, - usb_rcvctrlpipe(dev->udev, 0), - cmd, - USB_DIR_IN | USB_TYPE_VENDOR | USB_RECIP_DEVICE, - value, - index, - data, - size, - CONTROL_TIMEOUT_MS); -} - -static int ax8817x_write_cmd(struct usbnet *dev, u8 cmd, u16 value, u16 index, - u16 size, void *data) -{ - return usb_control_msg( - dev->udev, - usb_sndctrlpipe(dev->udev, 0), - cmd, - USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_DEVICE, - value, - index, - data, - size, - CONTROL_TIMEOUT_MS); -} - -static void ax8817x_async_cmd_callback(struct urb *urb, struct pt_regs *regs) -{ - struct usb_ctrlrequest *req = (struct usb_ctrlrequest *)urb->context; - - if (urb->status < 0) - printk(KERN_DEBUG "ax8817x_async_cmd_callback() failed with %d", - urb->status); - - kfree(req); - usb_free_urb(urb); -} - -static void ax8817x_status(struct usbnet *dev, struct urb *urb) -{ - struct ax88172_int_data *event; - int link; - - if (urb->actual_length < 8) - return; - - event = urb->transfer_buffer; - link = event->link & 0x01; - if (netif_carrier_ok(dev->net) != link) { - if (link) { - netif_carrier_on(dev->net); - defer_kevent (dev, EVENT_LINK_RESET ); - } else - netif_carrier_off(dev->net); - devdbg(dev, "ax8817x - Link Status is: %d", link); - } -} - -static void ax8817x_write_cmd_async(struct usbnet *dev, u8 cmd, u16 value, u16 index, - u16 size, void *data) -{ - struct usb_ctrlrequest *req; - int status; - struct urb *urb; - - if ((urb = usb_alloc_urb(0, GFP_ATOMIC)) == NULL) { - devdbg(dev, "Error allocating URB in write_cmd_async!"); - return; - } - - if ((req = kmalloc(sizeof(struct usb_ctrlrequest), GFP_ATOMIC)) == NULL) { - deverr(dev, "Failed to allocate memory for control request"); - usb_free_urb(urb); - return; - } - - req->bRequestType = USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_DEVICE; - req->bRequest = cmd; - req->wValue = cpu_to_le16(value); - req->wIndex = cpu_to_le16(index); - req->wLength = cpu_to_le16(size); - - usb_fill_control_urb(urb, dev->udev, - usb_sndctrlpipe(dev->udev, 0), - (void *)req, data, size, - ax8817x_async_cmd_callback, req); - - if((status = usb_submit_urb(urb, GFP_ATOMIC)) < 0) { - deverr(dev, "Error submitting the control message: status=%d", status); - kfree(req); - usb_free_urb(urb); - } -} - -static void ax8817x_set_multicast(struct net_device *net) -{ - struct usbnet *dev = netdev_priv(net); - struct ax8817x_data *data = (struct ax8817x_data *)&dev->data; - u8 rx_ctl = 0x8c; - - if (net->flags & IFF_PROMISC) { - rx_ctl |= 0x01; - } else if (net->flags & IFF_ALLMULTI - || net->mc_count > AX_MAX_MCAST) { - rx_ctl |= 0x02; - } else if (net->mc_count == 0) { - /* just broadcast and directed */ - } else { - /* We use the 20 byte dev->data - * for our 8 byte filter buffer - * to avoid allocating memory that - * is tricky to free later */ - struct dev_mc_list *mc_list = net->mc_list; - u32 crc_bits; - int i; - - memset(data->multi_filter, 0, AX_MCAST_FILTER_SIZE); - - /* Build the multicast hash filter. */ - for (i = 0; i < net->mc_count; i++) { - crc_bits = - ether_crc(ETH_ALEN, - mc_list->dmi_addr) >> 26; - data->multi_filter[crc_bits >> 3] |= - 1 << (crc_bits & 7); - mc_list = mc_list->next; - } - - ax8817x_write_cmd_async(dev, AX_CMD_WRITE_MULTI_FILTER, 0, 0, - AX_MCAST_FILTER_SIZE, data->multi_filter); - - rx_ctl |= 0x10; - } - - ax8817x_write_cmd_async(dev, AX_CMD_WRITE_RX_CTL, rx_ctl, 0, 0, NULL); -} - -static int ax8817x_mdio_read(struct net_device *netdev, int phy_id, int loc) -{ - struct usbnet *dev = netdev_priv(netdev); - u16 res; - u8 buf[1]; - - ax8817x_write_cmd(dev, AX_CMD_SET_SW_MII, 0, 0, 0, &buf); - ax8817x_read_cmd(dev, AX_CMD_READ_MII_REG, phy_id, (__u16)loc, 2, (u16 *)&res); - ax8817x_write_cmd(dev, AX_CMD_SET_HW_MII, 0, 0, 0, &buf); - - return res & 0xffff; -} - -static void ax8817x_mdio_write(struct net_device *netdev, int phy_id, int loc, int val) -{ - struct usbnet *dev = netdev_priv(netdev); - u16 res = val; - u8 buf[1]; - - ax8817x_write_cmd(dev, AX_CMD_SET_SW_MII, 0, 0, 0, &buf); - ax8817x_write_cmd(dev, AX_CMD_WRITE_MII_REG, phy_id, (__u16)loc, 2, (u16 *)&res); - ax8817x_write_cmd(dev, AX_CMD_SET_HW_MII, 0, 0, 0, &buf); -} - -static int ax88172_link_reset(struct usbnet *dev) -{ - u16 lpa; - u8 mode; - - mode = AX_MEDIUM_TX_ABORT_ALLOW | AX_MEDIUM_FLOW_CONTROL_EN; - lpa = ax8817x_mdio_read(dev->net, dev->mii.phy_id, MII_LPA); - if (lpa & LPA_DUPLEX) - mode |= AX_MEDIUM_FULL_DUPLEX; - ax8817x_write_cmd(dev, AX_CMD_WRITE_MEDIUM_MODE, mode, 0, 0, NULL); - - return 0; -} - -static void ax8817x_get_wol(struct net_device *net, struct ethtool_wolinfo *wolinfo) -{ - struct usbnet *dev = netdev_priv(net); - u8 opt; - - if (ax8817x_read_cmd(dev, AX_CMD_READ_MONITOR_MODE, 0, 0, 1, &opt) < 0) { - wolinfo->supported = 0; - wolinfo->wolopts = 0; - return; - } - wolinfo->supported = WAKE_PHY | WAKE_MAGIC; - wolinfo->wolopts = 0; - if (opt & AX_MONITOR_MODE) { - if (opt & AX_MONITOR_LINK) - wolinfo->wolopts |= WAKE_PHY; - if (opt & AX_MONITOR_MAGIC) - wolinfo->wolopts |= WAKE_MAGIC; - } -} - -static int ax8817x_set_wol(struct net_device *net, struct ethtool_wolinfo *wolinfo) -{ - struct usbnet *dev = netdev_priv(net); - u8 opt = 0; - u8 buf[1]; - - if (wolinfo->wolopts & WAKE_PHY) - opt |= AX_MONITOR_LINK; - if (wolinfo->wolopts & WAKE_MAGIC) - opt |= AX_MONITOR_MAGIC; - if (opt != 0) - opt |= AX_MONITOR_MODE; - - if (ax8817x_write_cmd(dev, AX_CMD_WRITE_MONITOR_MODE, - opt, 0, 0, &buf) < 0) - return -EINVAL; - - return 0; -} - -static int ax8817x_get_eeprom_len(struct net_device *net) -{ - return AX_EEPROM_LEN; -} - -static int ax8817x_get_eeprom(struct net_device *net, - struct ethtool_eeprom *eeprom, u8 *data) -{ - struct usbnet *dev = netdev_priv(net); - u16 *ebuf = (u16 *)data; - int i; - - /* Crude hack to ensure that we don't overwrite memory - * if an odd length is supplied - */ - if (eeprom->len % 2) - return -EINVAL; - - eeprom->magic = AX_EEPROM_MAGIC; - - /* ax8817x returns 2 bytes from eeprom on read */ - for (i=0; i < eeprom->len / 2; i++) { - if (ax8817x_read_cmd(dev, AX_CMD_READ_EEPROM, - eeprom->offset + i, 0, 2, &ebuf[i]) < 0) - return -EINVAL; - } - return 0; -} - -static void ax8817x_get_drvinfo (struct net_device *net, - struct ethtool_drvinfo *info) -{ - /* Inherit standard device info */ - usbnet_get_drvinfo(net, info); - info->eedump_len = 0x3e; -} - -static int ax8817x_get_settings(struct net_device *net, struct ethtool_cmd *cmd) -{ - struct usbnet *dev = netdev_priv(net); - - return mii_ethtool_gset(&dev->mii,cmd); -} - -static int ax8817x_set_settings(struct net_device *net, struct ethtool_cmd *cmd) -{ - struct usbnet *dev = netdev_priv(net); - - return mii_ethtool_sset(&dev->mii,cmd); -} - -/* We need to override some ethtool_ops so we require our - own structure so we don't interfere with other usbnet - devices that may be connected at the same time. */ -static struct ethtool_ops ax8817x_ethtool_ops = { - .get_drvinfo = ax8817x_get_drvinfo, - .get_link = ethtool_op_get_link, - .get_msglevel = usbnet_get_msglevel, - .set_msglevel = usbnet_set_msglevel, - .get_wol = ax8817x_get_wol, - .set_wol = ax8817x_set_wol, - .get_eeprom_len = ax8817x_get_eeprom_len, - .get_eeprom = ax8817x_get_eeprom, - .get_settings = ax8817x_get_settings, - .set_settings = ax8817x_set_settings, -}; - -static int ax8817x_bind(struct usbnet *dev, struct usb_interface *intf) -{ - int ret = 0; - void *buf; - int i; - unsigned long gpio_bits = dev->driver_info->data; - - get_endpoints(dev,intf); - - buf = kmalloc(ETH_ALEN, GFP_KERNEL); - if(!buf) { - ret = -ENOMEM; - goto out1; - } - - /* Toggle the GPIOs in a manufacturer/model specific way */ - for (i = 2; i >= 0; i--) { - if ((ret = ax8817x_write_cmd(dev, AX_CMD_WRITE_GPIOS, - (gpio_bits >> (i * 8)) & 0xff, 0, 0, - buf)) < 0) - goto out2; - msleep(5); - } - - if ((ret = ax8817x_write_cmd(dev, AX_CMD_WRITE_RX_CTL, 0x80, 0, 0, buf)) < 0) { - dbg("send AX_CMD_WRITE_RX_CTL failed: %d", ret); - goto out2; - } - - /* Get the MAC address */ - memset(buf, 0, ETH_ALEN); - if ((ret = ax8817x_read_cmd(dev, AX_CMD_READ_NODE_ID, 0, 0, 6, buf)) < 0) { - dbg("read AX_CMD_READ_NODE_ID failed: %d", ret); - goto out2; - } - memcpy(dev->net->dev_addr, buf, ETH_ALEN); - - /* Get the PHY id */ - if ((ret = ax8817x_read_cmd(dev, AX_CMD_READ_PHY_ID, 0, 0, 2, buf)) < 0) { - dbg("error on read AX_CMD_READ_PHY_ID: %02x", ret); - goto out2; - } else if (ret < 2) { - /* this should always return 2 bytes */ - dbg("AX_CMD_READ_PHY_ID returned less than 2 bytes: ret=%02x", ret); - ret = -EIO; - goto out2; - } - - /* Initialize MII structure */ - dev->mii.dev = dev->net; - dev->mii.mdio_read = ax8817x_mdio_read; - dev->mii.mdio_write = ax8817x_mdio_write; - dev->mii.phy_id_mask = 0x3f; - dev->mii.reg_num_mask = 0x1f; - dev->mii.phy_id = *((u8 *)buf + 1); - - dev->net->set_multicast_list = ax8817x_set_multicast; - dev->net->ethtool_ops = &ax8817x_ethtool_ops; - - ax8817x_mdio_write(dev->net, dev->mii.phy_id, MII_BMCR, BMCR_RESET); - ax8817x_mdio_write(dev->net, dev->mii.phy_id, MII_ADVERTISE, - ADVERTISE_ALL | ADVERTISE_CSMA | ADVERTISE_PAUSE_CAP); - mii_nway_restart(&dev->mii); - - return 0; -out2: - kfree(buf); -out1: - return ret; -} - -static struct ethtool_ops ax88772_ethtool_ops = { - .get_drvinfo = ax8817x_get_drvinfo, - .get_link = ethtool_op_get_link, - .get_msglevel = usbnet_get_msglevel, - .set_msglevel = usbnet_set_msglevel, - .get_wol = ax8817x_get_wol, - .set_wol = ax8817x_set_wol, - .get_eeprom_len = ax8817x_get_eeprom_len, - .get_eeprom = ax8817x_get_eeprom, - .get_settings = ax8817x_get_settings, - .set_settings = ax8817x_set_settings, -}; - -static int ax88772_bind(struct usbnet *dev, struct usb_interface *intf) -{ - int ret; - void *buf; - - get_endpoints(dev,intf); - - buf = kmalloc(6, GFP_KERNEL); - if(!buf) { - dbg ("Cannot allocate memory for buffer"); - ret = -ENOMEM; - goto out1; - } - - if ((ret = ax8817x_write_cmd(dev, AX_CMD_WRITE_GPIOS, - 0x00B0, 0, 0, buf)) < 0) - goto out2; - - msleep(5); - if ((ret = ax8817x_write_cmd(dev, AX_CMD_SW_PHY_SELECT, 0x0001, 0, 0, buf)) < 0) { - dbg("Select PHY #1 failed: %d", ret); - goto out2; - } - - if ((ret = - ax8817x_write_cmd(dev, AX_CMD_SW_RESET, AX_SWRESET_IPPD, 0, 0, buf)) < 0) { - dbg("Failed to power down internal PHY: %d", ret); - goto out2; - } - - msleep(150); - if ((ret = - ax8817x_write_cmd(dev, AX_CMD_SW_RESET, AX_SWRESET_CLEAR, 0, 0, buf)) < 0) { - dbg("Failed to perform software reset: %d", ret); - goto out2; - } - - msleep(150); - if ((ret = - ax8817x_write_cmd(dev, AX_CMD_SW_RESET, AX_SWRESET_IPRL | AX_SWRESET_PRL, 0, 0, buf)) < 0) { - dbg("Failed to set Internal/External PHY reset control: %d", ret); - goto out2; - } - - msleep(150); - if ((ret = - ax8817x_write_cmd(dev, AX_CMD_WRITE_RX_CTL, 0x0000, 0, 0, - buf)) < 0) { - dbg("Failed to reset RX_CTL: %d", ret); - goto out2; - } - - /* Get the MAC address */ - memset(buf, 0, ETH_ALEN); - if ((ret = ax8817x_read_cmd(dev, AX88772_CMD_READ_NODE_ID, 0, 0, ETH_ALEN, buf)) < 0) { - dbg("Failed to read MAC address: %d", ret); - goto out2; - } - memcpy(dev->net->dev_addr, buf, ETH_ALEN); - - if ((ret = ax8817x_write_cmd(dev, AX_CMD_SET_SW_MII, 0, 0, 0, buf)) < 0) { - dbg("Enabling software MII failed: %d", ret); - goto out2; - } - - if (((ret = - ax8817x_read_cmd(dev, AX_CMD_READ_MII_REG, 0x0010, 2, 2, buf)) < 0) - || (*((u16 *)buf) != 0x003b)) { - dbg("Read PHY register 2 must be 0x3b00: %d", ret); - goto out2; - } - - /* Initialize MII structure */ - dev->mii.dev = dev->net; - dev->mii.mdio_read = ax8817x_mdio_read; - dev->mii.mdio_write = ax8817x_mdio_write; - dev->mii.phy_id_mask = 0xff; - dev->mii.reg_num_mask = 0xff; - - /* Get the PHY id */ - if ((ret = ax8817x_read_cmd(dev, AX_CMD_READ_PHY_ID, 0, 0, 2, buf)) < 0) { - dbg("Error reading PHY ID: %02x", ret); - goto out2; - } else if (ret < 2) { - /* this should always return 2 bytes */ - dbg("AX_CMD_READ_PHY_ID returned less than 2 bytes: ret=%02x", - ret); - ret = -EIO; - goto out2; - } - dev->mii.phy_id = *((u8 *)buf + 1); - - if ((ret = - ax8817x_write_cmd(dev, AX_CMD_SW_RESET, AX_SWRESET_PRL, 0, 0, buf)) < 0) { - dbg("Set external PHY reset pin level: %d", ret); - goto out2; - } - msleep(150); - if ((ret = - ax8817x_write_cmd(dev, AX_CMD_SW_RESET, AX_SWRESET_IPRL | AX_SWRESET_PRL, 0, 0, buf)) < 0) { - dbg("Set Internal/External PHY reset control: %d", ret); - goto out2; - } - msleep(150); - - - dev->net->set_multicast_list = ax8817x_set_multicast; - dev->net->ethtool_ops = &ax88772_ethtool_ops; - - ax8817x_mdio_write(dev->net, dev->mii.phy_id, MII_BMCR, BMCR_RESET); - ax8817x_mdio_write(dev->net, dev->mii.phy_id, MII_ADVERTISE, - ADVERTISE_ALL | ADVERTISE_CSMA); - mii_nway_restart(&dev->mii); - - if ((ret = ax8817x_write_cmd(dev, AX_CMD_WRITE_MEDIUM_MODE, AX88772_MEDIUM_DEFAULT, 0, 0, buf)) < 0) { - dbg("Write medium mode register: %d", ret); - goto out2; - } - - if ((ret = ax8817x_write_cmd(dev, AX_CMD_WRITE_IPG0, AX88772_IPG0_DEFAULT | AX88772_IPG1_DEFAULT,AX88772_IPG2_DEFAULT, 0, buf)) < 0) { - dbg("Write IPG,IPG1,IPG2 failed: %d", ret); - goto out2; - } - if ((ret = - ax8817x_write_cmd(dev, AX_CMD_SET_HW_MII, 0, 0, 0, &buf)) < 0) { - dbg("Failed to set hardware MII: %02x", ret); - goto out2; - } - - /* Set RX_CTL to default values with 2k buffer, and enable cactus */ - if ((ret = - ax8817x_write_cmd(dev, AX_CMD_WRITE_RX_CTL, 0x0088, 0, 0, - buf)) < 0) { - dbg("Reset RX_CTL failed: %d", ret); - goto out2; - } - - kfree(buf); - - return 0; - -out2: - kfree(buf); -out1: - return ret; -} - -static int ax88772_rx_fixup(struct usbnet *dev, struct sk_buff *skb) -{ - u32 *header; - char *packet; - struct sk_buff *ax_skb; - u16 size; - - header = (u32 *) skb->data; - le32_to_cpus(header); - packet = (char *)(header + 1); - - skb_pull(skb, 4); - - while (skb->len > 0) { - if ((short)(*header & 0x0000ffff) != - ~((short)((*header & 0xffff0000) >> 16))) { - devdbg(dev,"header length data is error"); - } - /* get the packet length */ - size = (u16) (*header & 0x0000ffff); - - if ((skb->len) - ((size + 1) & 0xfffe) == 0) - return 2; - if (size > ETH_FRAME_LEN) { - devdbg(dev,"invalid rx length %d", size); - return 0; - } - ax_skb = skb_clone(skb, GFP_ATOMIC); - if (ax_skb) { - ax_skb->len = size; - ax_skb->data = packet; - ax_skb->tail = packet + size; - skb_return(dev, ax_skb); - } else { - return 0; - } - - skb_pull(skb, (size + 1) & 0xfffe); - - if (skb->len == 0) - break; - - header = (u32 *) skb->data; - le32_to_cpus(header); - packet = (char *)(header + 1); - skb_pull(skb, 4); - } - - if (skb->len < 0) { - devdbg(dev,"invalid rx length %d", skb->len); - return 0; - } - return 1; -} - -static struct sk_buff *ax88772_tx_fixup(struct usbnet *dev, struct sk_buff *skb, - unsigned flags) -{ - int padlen; - int headroom = skb_headroom(skb); - int tailroom = skb_tailroom(skb); - u32 *packet_len; - u32 *padbytes_ptr; - - padlen = ((skb->len + 4) % 512) ? 0 : 4; - - if ((!skb_cloned(skb)) - && ((headroom + tailroom) >= (4 + padlen))) { - if ((headroom < 4) || (tailroom < padlen)) { - skb->data = memmove(skb->head + 4, skb->data, skb->len); - skb->tail = skb->data + skb->len; - } - } else { - struct sk_buff *skb2; - skb2 = skb_copy_expand(skb, 4, padlen, flags); - dev_kfree_skb_any(skb); - skb = skb2; - if (!skb) - return NULL; - } - - packet_len = (u32 *) skb_push(skb, 4); - - packet_len = (u32 *) skb->data; - *packet_len = (((skb->len - 4) ^ 0x0000ffff) << 16) + (skb->len - 4); - - if ((skb->len % 512) == 0) { - padbytes_ptr = (u32 *) skb->tail; - *padbytes_ptr = 0xffff0000; - skb_put(skb, padlen); - } - return skb; -} - -static int ax88772_link_reset(struct usbnet *dev) -{ - u16 lpa; - u16 mode; - - mode = AX88772_MEDIUM_DEFAULT; - lpa = ax8817x_mdio_read(dev->net, dev->mii.phy_id, MII_LPA); - - if ((lpa & LPA_DUPLEX) == 0) - mode &= ~AX88772_MEDIUM_FULL_DUPLEX; - if ((lpa & LPA_100) == 0) - mode &= ~AX88772_MEDIUM_100MB; - ax8817x_write_cmd(dev, AX_CMD_WRITE_MEDIUM_MODE, mode, 0, 0, NULL); - - return 0; -} - -static const struct driver_info ax8817x_info = { - .description = "ASIX AX8817x USB 2.0 Ethernet", - .bind = ax8817x_bind, - .status = ax8817x_status, - .link_reset = ax88172_link_reset, - .reset = ax88172_link_reset, - .flags = FLAG_ETHER, - .data = 0x00130103, -}; - -static const struct driver_info dlink_dub_e100_info = { - .description = "DLink DUB-E100 USB Ethernet", - .bind = ax8817x_bind, - .status = ax8817x_status, - .link_reset = ax88172_link_reset, - .reset = ax88172_link_reset, - .flags = FLAG_ETHER, - .data = 0x009f9d9f, -}; - -static const struct driver_info netgear_fa120_info = { - .description = "Netgear FA-120 USB Ethernet", - .bind = ax8817x_bind, - .status = ax8817x_status, - .link_reset = ax88172_link_reset, - .reset = ax88172_link_reset, - .flags = FLAG_ETHER, - .data = 0x00130103, -}; - -static const struct driver_info hawking_uf200_info = { - .description = "Hawking UF200 USB Ethernet", - .bind = ax8817x_bind, - .status = ax8817x_status, - .link_reset = ax88172_link_reset, - .reset = ax88172_link_reset, - .flags = FLAG_ETHER, - .data = 0x001f1d1f, -}; - -static const struct driver_info ax88772_info = { - .description = "ASIX AX88772 USB 2.0 Ethernet", - .bind = ax88772_bind, - .status = ax8817x_status, - .link_reset = ax88772_link_reset, - .reset = ax88772_link_reset, - .flags = FLAG_ETHER | FLAG_FRAMING_AX, - .rx_fixup = ax88772_rx_fixup, - .tx_fixup = ax88772_tx_fixup, - .data = 0x00130103, -}; - -#endif /* CONFIG_USB_AX8817X */ - - - -#ifdef CONFIG_USB_BELKIN -#define HAVE_HARDWARE - -/*------------------------------------------------------------------------- - * - * Belkin F5U104 ... two NetChip 2280 devices + Atmel microcontroller - * - * ... also two eTEK designs, including one sold as "Advance USBNET" - * - *-------------------------------------------------------------------------*/ - -static const struct driver_info belkin_info = { - .description = "Belkin, eTEK, or compatible", -}; - -#endif /* CONFIG_USB_BELKIN */ - - - -/*------------------------------------------------------------------------- - * - * Communications Device Class declarations. - * Used by CDC Ethernet, and some CDC variants - * - *-------------------------------------------------------------------------*/ - -#ifdef CONFIG_USB_CDCETHER -#define NEED_GENERIC_CDC -#endif - -#ifdef CONFIG_USB_ZAURUS -/* Ethernet variant uses funky framing, broken ethernet addressing */ -#define NEED_GENERIC_CDC -#endif - -#ifdef CONFIG_USB_RNDIS -/* ACM variant uses even funkier framing, complex control RPC scheme */ -#define NEED_GENERIC_CDC -#endif - - -#ifdef NEED_GENERIC_CDC - -#include - -struct cdc_state { - struct usb_cdc_header_desc *header; - struct usb_cdc_union_desc *u; - struct usb_cdc_ether_desc *ether; - struct usb_interface *control; - struct usb_interface *data; -}; - -static struct usb_driver usbnet_driver; - -/* - * probes control interface, claims data interface, collects the bulk - * endpoints, activates data interface (if needed), maybe sets MTU. - * all pure cdc, except for certain firmware workarounds. - */ -static int generic_cdc_bind (struct usbnet *dev, struct usb_interface *intf) -{ - u8 *buf = intf->cur_altsetting->extra; - int len = intf->cur_altsetting->extralen; - struct usb_interface_descriptor *d; - struct cdc_state *info = (void *) &dev->data; - int status; - int rndis; - - if (sizeof dev->data < sizeof *info) - return -EDOM; - - /* expect strict spec conformance for the descriptors, but - * cope with firmware which stores them in the wrong place - */ - if (len == 0 && dev->udev->actconfig->extralen) { - /* Motorola SB4100 (and others: Brad Hards says it's - * from a Broadcom design) put CDC descriptors here - */ - buf = dev->udev->actconfig->extra; - len = dev->udev->actconfig->extralen; - if (len) - dev_dbg (&intf->dev, - "CDC descriptors on config\n"); - } - - /* this assumes that if there's a non-RNDIS vendor variant - * of cdc-acm, it'll fail RNDIS requests cleanly. - */ - rndis = (intf->cur_altsetting->desc.bInterfaceProtocol == 0xff); - - memset (info, 0, sizeof *info); - info->control = intf; - while (len > 3) { - if (buf [1] != USB_DT_CS_INTERFACE) - goto next_desc; - - /* use bDescriptorSubType to identify the CDC descriptors. - * We expect devices with CDC header and union descriptors. - * For CDC Ethernet we need the ethernet descriptor. - * For RNDIS, ignore two (pointless) CDC modem descriptors - * in favor of a complicated OID-based RPC scheme doing what - * CDC Ethernet achieves with a simple descriptor. - */ - switch (buf [2]) { - case USB_CDC_HEADER_TYPE: - if (info->header) { - dev_dbg (&intf->dev, "extra CDC header\n"); - goto bad_desc; - } - info->header = (void *) buf; - if (info->header->bLength != sizeof *info->header) { - dev_dbg (&intf->dev, "CDC header len %u\n", - info->header->bLength); - goto bad_desc; - } - break; - case USB_CDC_UNION_TYPE: - if (info->u) { - dev_dbg (&intf->dev, "extra CDC union\n"); - goto bad_desc; - } - info->u = (void *) buf; - if (info->u->bLength != sizeof *info->u) { - dev_dbg (&intf->dev, "CDC union len %u\n", - info->u->bLength); - goto bad_desc; - } - - /* we need a master/control interface (what we're - * probed with) and a slave/data interface; union - * descriptors sort this all out. - */ - info->control = usb_ifnum_to_if(dev->udev, - info->u->bMasterInterface0); - info->data = usb_ifnum_to_if(dev->udev, - info->u->bSlaveInterface0); - if (!info->control || !info->data) { - dev_dbg (&intf->dev, - "master #%u/%p slave #%u/%p\n", - info->u->bMasterInterface0, - info->control, - info->u->bSlaveInterface0, - info->data); - goto bad_desc; - } - if (info->control != intf) { - dev_dbg (&intf->dev, "bogus CDC Union\n"); - /* Ambit USB Cable Modem (and maybe others) - * interchanges master and slave interface. - */ - if (info->data == intf) { - info->data = info->control; - info->control = intf; - } else - goto bad_desc; - } - - /* a data interface altsetting does the real i/o */ - d = &info->data->cur_altsetting->desc; - if (d->bInterfaceClass != USB_CLASS_CDC_DATA) { - dev_dbg (&intf->dev, "slave class %u\n", - d->bInterfaceClass); - goto bad_desc; - } - break; - case USB_CDC_ETHERNET_TYPE: - if (info->ether) { - dev_dbg (&intf->dev, "extra CDC ether\n"); - goto bad_desc; - } - info->ether = (void *) buf; - if (info->ether->bLength != sizeof *info->ether) { - dev_dbg (&intf->dev, "CDC ether len %u\n", - info->ether->bLength); - goto bad_desc; - } - dev->net->mtu = le16_to_cpup ( - &info->ether->wMaxSegmentSize) - - ETH_HLEN; - /* because of Zaurus, we may be ignoring the host - * side link address we were given. - */ - break; - } -next_desc: - len -= buf [0]; /* bLength */ - buf += buf [0]; - } - - if (!info->header || !info->u || (!rndis && !info->ether)) { - dev_dbg (&intf->dev, "missing cdc %s%s%sdescriptor\n", - info->header ? "" : "header ", - info->u ? "" : "union ", - info->ether ? "" : "ether "); - goto bad_desc; - } - - /* claim data interface and set it up ... with side effects. - * network traffic can't flow until an altsetting is enabled. - */ - status = usb_driver_claim_interface (&usbnet_driver, info->data, dev); - if (status < 0) - return status; - status = get_endpoints (dev, info->data); - if (status < 0) { - /* ensure immediate exit from usbnet_disconnect */ - usb_set_intfdata(info->data, NULL); - usb_driver_release_interface (&usbnet_driver, info->data); - return status; - } - - /* status endpoint: optional for CDC Ethernet, not RNDIS (or ACM) */ - dev->status = NULL; - if (info->control->cur_altsetting->desc.bNumEndpoints == 1) { - struct usb_endpoint_descriptor *desc; - - dev->status = &info->control->cur_altsetting->endpoint [0]; - desc = &dev->status->desc; - if (desc->bmAttributes != USB_ENDPOINT_XFER_INT - || !(desc->bEndpointAddress & USB_DIR_IN) - || (le16_to_cpu(desc->wMaxPacketSize) - < sizeof (struct usb_cdc_notification)) - || !desc->bInterval) { - dev_dbg (&intf->dev, "bad notification endpoint\n"); - dev->status = NULL; - } - } - if (rndis && !dev->status) { - dev_dbg (&intf->dev, "missing RNDIS status endpoint\n"); - usb_set_intfdata(info->data, NULL); - usb_driver_release_interface (&usbnet_driver, info->data); - return -ENODEV; - } - return 0; - -bad_desc: - dev_info (&dev->udev->dev, "bad CDC descriptors\n"); - return -ENODEV; -} - -static void cdc_unbind (struct usbnet *dev, struct usb_interface *intf) -{ - struct cdc_state *info = (void *) &dev->data; - - /* disconnect master --> disconnect slave */ - if (intf == info->control && info->data) { - /* ensure immediate exit from usbnet_disconnect */ - usb_set_intfdata(info->data, NULL); - usb_driver_release_interface (&usbnet_driver, info->data); - info->data = NULL; - } - - /* and vice versa (just in case) */ - else if (intf == info->data && info->control) { - /* ensure immediate exit from usbnet_disconnect */ - usb_set_intfdata(info->control, NULL); - usb_driver_release_interface (&usbnet_driver, info->control); - info->control = NULL; - } -} - -#endif /* NEED_GENERIC_CDC */ - - -#ifdef CONFIG_USB_CDCETHER -#define HAVE_HARDWARE - -/*------------------------------------------------------------------------- - * - * Communications Device Class, Ethernet Control model - * - * Takes two interfaces. The DATA interface is inactive till an altsetting - * is selected. Configuration data includes class descriptors. - * - * This should interop with whatever the 2.4 "CDCEther.c" driver - * (by Brad Hards) talked with. - * - *-------------------------------------------------------------------------*/ - -#include - - -static void dumpspeed (struct usbnet *dev, __le32 *speeds) -{ - if (netif_msg_timer (dev)) - devinfo (dev, "link speeds: %u kbps up, %u kbps down", - __le32_to_cpu(speeds[0]) / 1000, - __le32_to_cpu(speeds[1]) / 1000); -} - -static void cdc_status (struct usbnet *dev, struct urb *urb) -{ - struct usb_cdc_notification *event; - - if (urb->actual_length < sizeof *event) - return; - - /* SPEED_CHANGE can get split into two 8-byte packets */ - if (test_and_clear_bit (EVENT_STS_SPLIT, &dev->flags)) { - dumpspeed (dev, (__le32 *) urb->transfer_buffer); - return; - } - - event = urb->transfer_buffer; - switch (event->bNotificationType) { - case USB_CDC_NOTIFY_NETWORK_CONNECTION: - if (netif_msg_timer (dev)) - devdbg (dev, "CDC: carrier %s", - event->wValue ? "on" : "off"); - if (event->wValue) - netif_carrier_on(dev->net); - else - netif_carrier_off(dev->net); - break; - case USB_CDC_NOTIFY_SPEED_CHANGE: /* tx/rx rates */ - if (netif_msg_timer (dev)) - devdbg (dev, "CDC: speed change (len %d)", - urb->actual_length); - if (urb->actual_length != (sizeof *event + 8)) - set_bit (EVENT_STS_SPLIT, &dev->flags); - else - dumpspeed (dev, (__le32 *) &event[1]); - break; - // case USB_CDC_NOTIFY_RESPONSE_AVAILABLE: /* RNDIS; or unsolicited */ - default: - deverr (dev, "CDC: unexpected notification %02x!", - event->bNotificationType); - break; - } -} - -static u8 nibble (unsigned char c) -{ - if (likely (isdigit (c))) - return c - '0'; - c = toupper (c); - if (likely (isxdigit (c))) - return 10 + c - 'A'; - return 0; -} - -static inline int -get_ethernet_addr (struct usbnet *dev, struct usb_cdc_ether_desc *e) -{ - int tmp, i; - unsigned char buf [13]; - - tmp = usb_string (dev->udev, e->iMACAddress, buf, sizeof buf); - if (tmp != 12) { - dev_dbg (&dev->udev->dev, - "bad MAC string %d fetch, %d\n", e->iMACAddress, tmp); - if (tmp >= 0) - tmp = -EINVAL; - return tmp; - } - for (i = tmp = 0; i < 6; i++, tmp += 2) - dev->net->dev_addr [i] = - (nibble (buf [tmp]) << 4) + nibble (buf [tmp + 1]); - return 0; -} - -static int cdc_bind (struct usbnet *dev, struct usb_interface *intf) -{ - int status; - struct cdc_state *info = (void *) &dev->data; - - status = generic_cdc_bind (dev, intf); - if (status < 0) - return status; - - status = get_ethernet_addr (dev, info->ether); - if (status < 0) { - usb_set_intfdata(info->data, NULL); - usb_driver_release_interface (&usbnet_driver, info->data); - return status; - } - - /* FIXME cdc-ether has some multicast code too, though it complains - * in routine cases. info->ether describes the multicast support. - */ - return 0; -} - -static const struct driver_info cdc_info = { - .description = "CDC Ethernet Device", - .flags = FLAG_ETHER, - // .check_connect = cdc_check_connect, - .bind = cdc_bind, - .unbind = cdc_unbind, - .status = cdc_status, -}; - -#endif /* CONFIG_USB_CDCETHER */ - - - -#ifdef CONFIG_USB_EPSON2888 -#define HAVE_HARDWARE - -/*------------------------------------------------------------------------- - * - * EPSON USB clients - * - * This is the same idea as Linux PDAs (below) except the firmware in the - * device might not be Tux-powered. Epson provides reference firmware that - * implements this interface. Product developers can reuse or modify that - * code, such as by using their own product and vendor codes. - * - * Support was from Juro Bystricky - * - *-------------------------------------------------------------------------*/ - -static const struct driver_info epson2888_info = { - .description = "Epson USB Device", - .check_connect = always_connected, - - .in = 4, .out = 3, -}; - -#endif /* CONFIG_USB_EPSON2888 */ - - -#ifdef CONFIG_USB_GENESYS -#define HAVE_HARDWARE - -/*------------------------------------------------------------------------- - * - * GeneSys GL620USB-A (www.genesyslogic.com.tw) - * - * ... should partially interop with the Win32 driver for this hardware - * The GeneSys docs imply there's some NDIS issue motivating this framing. - * - * Some info from GeneSys: - * - GL620USB-A is full duplex; GL620USB is only half duplex for bulk. - * (Some cables, like the BAFO-100c, use the half duplex version.) - * - For the full duplex model, the low bit of the version code says - * which side is which ("left/right"). - * - For the half duplex type, a control/interrupt handshake settles - * the transfer direction. (That's disabled here, partially coded.) - * A control URB would block until other side writes an interrupt. - * - * Original code from Jiun-Jie Huang - * and merged into "usbnet" by Stanislav Brabec . - * - *-------------------------------------------------------------------------*/ - -// control msg write command -#define GENELINK_CONNECT_WRITE 0xF0 -// interrupt pipe index -#define GENELINK_INTERRUPT_PIPE 0x03 -// interrupt read buffer size -#define INTERRUPT_BUFSIZE 0x08 -// interrupt pipe interval value -#define GENELINK_INTERRUPT_INTERVAL 0x10 -// max transmit packet number per transmit -#define GL_MAX_TRANSMIT_PACKETS 32 -// max packet length -#define GL_MAX_PACKET_LEN 1514 -// max receive buffer size -#define GL_RCV_BUF_SIZE \ - (((GL_MAX_PACKET_LEN + 4) * GL_MAX_TRANSMIT_PACKETS) + 4) - -struct gl_packet { - u32 packet_length; - char packet_data [1]; -}; - -struct gl_header { - u32 packet_count; - struct gl_packet packets; -}; - -#ifdef GENELINK_ACK - -// FIXME: this code is incomplete, not debugged; it doesn't -// handle interrupts correctly. interrupts should be generic -// code like all other device I/O, anyway. - -struct gl_priv { - struct urb *irq_urb; - char irq_buf [INTERRUPT_BUFSIZE]; -}; - -static inline int gl_control_write (struct usbnet *dev, u8 request, u16 value) -{ - int retval; - - retval = usb_control_msg (dev->udev, - usb_sndctrlpipe (dev->udev, 0), - request, - USB_DIR_OUT | USB_TYPE_CLASS | USB_RECIP_INTERFACE, - value, - 0, // index - 0, // data buffer - 0, // size - CONTROL_TIMEOUT_MS); - return retval; -} - -static void gl_interrupt_complete (struct urb *urb, struct pt_regs *regs) -{ - int status = urb->status; - - switch (status) { - case 0: - /* success */ - break; - case -ECONNRESET: - case -ENOENT: - case -ESHUTDOWN: - /* this urb is terminated, clean up */ - dbg("%s - urb shutting down with status: %d", - __FUNCTION__, status); - return; - default: - dbg("%s - nonzero urb status received: %d", - __FUNCTION__, urb->status); - } - - status = usb_submit_urb (urb, GFP_ATOMIC); - if (status) - err ("%s - usb_submit_urb failed with result %d", - __FUNCTION__, status); -} - -static int gl_interrupt_read (struct usbnet *dev) -{ - struct gl_priv *priv = dev->priv_data; - int retval; - - // issue usb interrupt read - if (priv && priv->irq_urb) { - // submit urb - if ((retval = usb_submit_urb (priv->irq_urb, GFP_KERNEL)) != 0) - dbg ("gl_interrupt_read: submit fail - %X...", retval); - else - dbg ("gl_interrupt_read: submit success..."); - } - - return 0; -} - -// check whether another side is connected -static int genelink_check_connect (struct usbnet *dev) -{ - int retval; - - dbg ("genelink_check_connect..."); - - // detect whether another side is connected - if ((retval = gl_control_write (dev, GENELINK_CONNECT_WRITE, 0)) != 0) { - dbg ("%s: genelink_check_connect write fail - %X", - dev->net->name, retval); - return retval; - } - - // usb interrupt read to ack another side - if ((retval = gl_interrupt_read (dev)) != 0) { - dbg ("%s: genelink_check_connect read fail - %X", - dev->net->name, retval); - return retval; - } - - dbg ("%s: genelink_check_connect read success", dev->net->name); - return 0; -} - -// allocate and initialize the private data for genelink -static int genelink_init (struct usbnet *dev) -{ - struct gl_priv *priv; - - // allocate the private data structure - if ((priv = kmalloc (sizeof *priv, GFP_KERNEL)) == 0) { - dbg ("%s: cannot allocate private data per device", - dev->net->name); - return -ENOMEM; - } - - // allocate irq urb - if ((priv->irq_urb = usb_alloc_urb (0, GFP_KERNEL)) == 0) { - dbg ("%s: cannot allocate private irq urb per device", - dev->net->name); - kfree (priv); - return -ENOMEM; - } - - // fill irq urb - usb_fill_int_urb (priv->irq_urb, dev->udev, - usb_rcvintpipe (dev->udev, GENELINK_INTERRUPT_PIPE), - priv->irq_buf, INTERRUPT_BUFSIZE, - gl_interrupt_complete, 0, - GENELINK_INTERRUPT_INTERVAL); - - // set private data pointer - dev->priv_data = priv; - - return 0; -} - -// release the private data -static int genelink_free (struct usbnet *dev) -{ - struct gl_priv *priv = dev->priv_data; - - if (!priv) - return 0; - -// FIXME: can't cancel here; it's synchronous, and -// should have happened earlier in any case (interrupt -// handling needs to be generic) - - // cancel irq urb first - usb_kill_urb (priv->irq_urb); - - // free irq urb - usb_free_urb (priv->irq_urb); - - // free the private data structure - kfree (priv); - - return 0; -} - -#endif - -static int genelink_rx_fixup (struct usbnet *dev, struct sk_buff *skb) -{ - struct gl_header *header; - struct gl_packet *packet; - struct sk_buff *gl_skb; - u32 size; - - header = (struct gl_header *) skb->data; - - // get the packet count of the received skb - le32_to_cpus (&header->packet_count); - if ((header->packet_count > GL_MAX_TRANSMIT_PACKETS) - || (header->packet_count < 0)) { - dbg ("genelink: invalid received packet count %d", - header->packet_count); - return 0; - } - - // set the current packet pointer to the first packet - packet = &header->packets; - - // decrement the length for the packet count size 4 bytes - skb_pull (skb, 4); - - while (header->packet_count > 1) { - // get the packet length - size = packet->packet_length; - - // this may be a broken packet - if (size > GL_MAX_PACKET_LEN) { - dbg ("genelink: invalid rx length %d", size); - return 0; - } - - // allocate the skb for the individual packet - gl_skb = alloc_skb (size, GFP_ATOMIC); - if (gl_skb) { - - // copy the packet data to the new skb - memcpy(skb_put(gl_skb, size), packet->packet_data, size); - skb_return (dev, gl_skb); - } - - // advance to the next packet - packet = (struct gl_packet *) - &packet->packet_data [size]; - header->packet_count--; - - // shift the data pointer to the next gl_packet - skb_pull (skb, size + 4); - } - - // skip the packet length field 4 bytes - skb_pull (skb, 4); - - if (skb->len > GL_MAX_PACKET_LEN) { - dbg ("genelink: invalid rx length %d", skb->len); - return 0; - } - return 1; -} - -static struct sk_buff * -genelink_tx_fixup (struct usbnet *dev, struct sk_buff *skb, unsigned flags) -{ - int padlen; - int length = skb->len; - int headroom = skb_headroom (skb); - int tailroom = skb_tailroom (skb); - u32 *packet_count; - u32 *packet_len; - - // FIXME: magic numbers, bleech - padlen = ((skb->len + (4 + 4*1)) % 64) ? 0 : 1; - - if ((!skb_cloned (skb)) - && ((headroom + tailroom) >= (padlen + (4 + 4*1)))) { - if ((headroom < (4 + 4*1)) || (tailroom < padlen)) { - skb->data = memmove (skb->head + (4 + 4*1), - skb->data, skb->len); - skb->tail = skb->data + skb->len; - } - } else { - struct sk_buff *skb2; - skb2 = skb_copy_expand (skb, (4 + 4*1) , padlen, flags); - dev_kfree_skb_any (skb); - skb = skb2; - if (!skb) - return NULL; - } - - // attach the packet count to the header - packet_count = (u32 *) skb_push (skb, (4 + 4*1)); - packet_len = packet_count + 1; - - // FIXME little endian? - *packet_count = 1; - *packet_len = length; - - // add padding byte - if ((skb->len % dev->maxpacket) == 0) - skb_put (skb, 1); - - return skb; -} - -static const struct driver_info genelink_info = { - .description = "Genesys GeneLink", - .flags = FLAG_FRAMING_GL | FLAG_NO_SETINT, - .rx_fixup = genelink_rx_fixup, - .tx_fixup = genelink_tx_fixup, - - .in = 1, .out = 2, - -#ifdef GENELINK_ACK - .check_connect =genelink_check_connect, -#endif -}; - -#endif /* CONFIG_USB_GENESYS */ - - - -#ifdef CONFIG_USB_NET1080 -#define HAVE_HARDWARE - -/*------------------------------------------------------------------------- - * - * Netchip 1080 driver ... http://www.netchip.com - * Used in LapLink cables - * - *-------------------------------------------------------------------------*/ - -#define dev_packet_id data[0] -#define frame_errors data[1] - -/* - * NetChip framing of ethernet packets, supporting additional error - * checks for links that may drop bulk packets from inside messages. - * Odd USB length == always short read for last usb packet. - * - nc_header - * - Ethernet header (14 bytes) - * - payload - * - (optional padding byte, if needed so length becomes odd) - * - nc_trailer - * - * This framing is to be avoided for non-NetChip devices. - */ - -struct nc_header { // packed: - __le16 hdr_len; // sizeof nc_header (LE, all) - __le16 packet_len; // payload size (including ethhdr) - __le16 packet_id; // detects dropped packets -#define MIN_HEADER 6 - - // all else is optional, and must start with: - // u16 vendorId; // from usb-if - // u16 productId; -} __attribute__((__packed__)); - -#define PAD_BYTE ((unsigned char)0xAC) - -struct nc_trailer { - __le16 packet_id; -} __attribute__((__packed__)); - -// packets may use FLAG_FRAMING_NC and optional pad -#define FRAMED_SIZE(mtu) (sizeof (struct nc_header) \ - + sizeof (struct ethhdr) \ - + (mtu) \ - + 1 \ - + sizeof (struct nc_trailer)) - -#define MIN_FRAMED FRAMED_SIZE(0) - - -/* - * Zero means no timeout; else, how long a 64 byte bulk packet may be queued - * before the hardware drops it. If that's done, the driver will need to - * frame network packets to guard against the dropped USB packets. The win32 - * driver sets this for both sides of the link. - */ -#define NC_READ_TTL_MS ((u8)255) // ms - -/* - * We ignore most registers and EEPROM contents. - */ -#define REG_USBCTL ((u8)0x04) -#define REG_TTL ((u8)0x10) -#define REG_STATUS ((u8)0x11) - -/* - * Vendor specific requests to read/write data - */ -#define REQUEST_REGISTER ((u8)0x10) -#define REQUEST_EEPROM ((u8)0x11) - -static int -nc_vendor_read (struct usbnet *dev, u8 req, u8 regnum, u16 *retval_ptr) -{ - int status = usb_control_msg (dev->udev, - usb_rcvctrlpipe (dev->udev, 0), - req, - USB_DIR_IN | USB_TYPE_VENDOR | USB_RECIP_DEVICE, - 0, regnum, - retval_ptr, sizeof *retval_ptr, - CONTROL_TIMEOUT_MS); - if (status > 0) - status = 0; - if (!status) - le16_to_cpus (retval_ptr); - return status; -} - -static inline int -nc_register_read (struct usbnet *dev, u8 regnum, u16 *retval_ptr) -{ - return nc_vendor_read (dev, REQUEST_REGISTER, regnum, retval_ptr); -} - -// no retval ... can become async, usable in_interrupt() -static void -nc_vendor_write (struct usbnet *dev, u8 req, u8 regnum, u16 value) -{ - usb_control_msg (dev->udev, - usb_sndctrlpipe (dev->udev, 0), - req, - USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_DEVICE, - value, regnum, - NULL, 0, // data is in setup packet - CONTROL_TIMEOUT_MS); -} - -static inline void -nc_register_write (struct usbnet *dev, u8 regnum, u16 value) -{ - nc_vendor_write (dev, REQUEST_REGISTER, regnum, value); -} - - -#if 0 -static void nc_dump_registers (struct usbnet *dev) -{ - u8 reg; - u16 *vp = kmalloc (sizeof (u16)); - - if (!vp) { - dbg ("no memory?"); - return; - } - - dbg ("%s registers:", dev->net->name); - for (reg = 0; reg < 0x20; reg++) { - int retval; - - // reading some registers is trouble - if (reg >= 0x08 && reg <= 0xf) - continue; - if (reg >= 0x12 && reg <= 0x1e) - continue; - - retval = nc_register_read (dev, reg, vp); - if (retval < 0) - dbg ("%s reg [0x%x] ==> error %d", - dev->net->name, reg, retval); - else - dbg ("%s reg [0x%x] = 0x%x", - dev->net->name, reg, *vp); - } - kfree (vp); -} -#endif - - -/*-------------------------------------------------------------------------*/ - -/* - * Control register - */ - -#define USBCTL_WRITABLE_MASK 0x1f0f -// bits 15-13 reserved, r/o -#define USBCTL_ENABLE_LANG (1 << 12) -#define USBCTL_ENABLE_MFGR (1 << 11) -#define USBCTL_ENABLE_PROD (1 << 10) -#define USBCTL_ENABLE_SERIAL (1 << 9) -#define USBCTL_ENABLE_DEFAULTS (1 << 8) -// bits 7-4 reserved, r/o -#define USBCTL_FLUSH_OTHER (1 << 3) -#define USBCTL_FLUSH_THIS (1 << 2) -#define USBCTL_DISCONN_OTHER (1 << 1) -#define USBCTL_DISCONN_THIS (1 << 0) - -static inline void nc_dump_usbctl (struct usbnet *dev, u16 usbctl) -{ - if (!netif_msg_link (dev)) - return; - devdbg (dev, "net1080 %s-%s usbctl 0x%x:%s%s%s%s%s;" - " this%s%s;" - " other%s%s; r/o 0x%x", - dev->udev->bus->bus_name, dev->udev->devpath, - usbctl, - (usbctl & USBCTL_ENABLE_LANG) ? " lang" : "", - (usbctl & USBCTL_ENABLE_MFGR) ? " mfgr" : "", - (usbctl & USBCTL_ENABLE_PROD) ? " prod" : "", - (usbctl & USBCTL_ENABLE_SERIAL) ? " serial" : "", - (usbctl & USBCTL_ENABLE_DEFAULTS) ? " defaults" : "", - - (usbctl & USBCTL_FLUSH_OTHER) ? " FLUSH" : "", - (usbctl & USBCTL_DISCONN_OTHER) ? " DIS" : "", - (usbctl & USBCTL_FLUSH_THIS) ? " FLUSH" : "", - (usbctl & USBCTL_DISCONN_THIS) ? " DIS" : "", - usbctl & ~USBCTL_WRITABLE_MASK - ); -} - -/*-------------------------------------------------------------------------*/ - -/* - * Status register - */ - -#define STATUS_PORT_A (1 << 15) - -#define STATUS_CONN_OTHER (1 << 14) -#define STATUS_SUSPEND_OTHER (1 << 13) -#define STATUS_MAILBOX_OTHER (1 << 12) -#define STATUS_PACKETS_OTHER(n) (((n) >> 8) && 0x03) - -#define STATUS_CONN_THIS (1 << 6) -#define STATUS_SUSPEND_THIS (1 << 5) -#define STATUS_MAILBOX_THIS (1 << 4) -#define STATUS_PACKETS_THIS(n) (((n) >> 0) && 0x03) - -#define STATUS_UNSPEC_MASK 0x0c8c -#define STATUS_NOISE_MASK ((u16)~(0x0303|STATUS_UNSPEC_MASK)) - - -static inline void nc_dump_status (struct usbnet *dev, u16 status) -{ - if (!netif_msg_link (dev)) - return; - devdbg (dev, "net1080 %s-%s status 0x%x:" - " this (%c) PKT=%d%s%s%s;" - " other PKT=%d%s%s%s; unspec 0x%x", - dev->udev->bus->bus_name, dev->udev->devpath, - status, - - // XXX the packet counts don't seem right - // (1 at reset, not 0); maybe UNSPEC too - - (status & STATUS_PORT_A) ? 'A' : 'B', - STATUS_PACKETS_THIS (status), - (status & STATUS_CONN_THIS) ? " CON" : "", - (status & STATUS_SUSPEND_THIS) ? " SUS" : "", - (status & STATUS_MAILBOX_THIS) ? " MBOX" : "", - - STATUS_PACKETS_OTHER (status), - (status & STATUS_CONN_OTHER) ? " CON" : "", - (status & STATUS_SUSPEND_OTHER) ? " SUS" : "", - (status & STATUS_MAILBOX_OTHER) ? " MBOX" : "", - - status & STATUS_UNSPEC_MASK - ); -} - -/*-------------------------------------------------------------------------*/ - -/* - * TTL register - */ - -#define TTL_THIS(ttl) (0x00ff & ttl) -#define TTL_OTHER(ttl) (0x00ff & (ttl >> 8)) -#define MK_TTL(this,other) ((u16)(((other)<<8)|(0x00ff&(this)))) - -static inline void nc_dump_ttl (struct usbnet *dev, u16 ttl) -{ - if (netif_msg_link (dev)) - devdbg (dev, "net1080 %s-%s ttl 0x%x this = %d, other = %d", - dev->udev->bus->bus_name, dev->udev->devpath, - ttl, TTL_THIS (ttl), TTL_OTHER (ttl)); -} - -/*-------------------------------------------------------------------------*/ - -static int net1080_reset (struct usbnet *dev) -{ - u16 usbctl, status, ttl; - u16 *vp = kmalloc (sizeof (u16), GFP_KERNEL); - int retval; - - if (!vp) - return -ENOMEM; - - // nc_dump_registers (dev); - - if ((retval = nc_register_read (dev, REG_STATUS, vp)) < 0) { - dbg ("can't read %s-%s status: %d", - dev->udev->bus->bus_name, dev->udev->devpath, retval); - goto done; - } - status = *vp; - nc_dump_status (dev, status); - - if ((retval = nc_register_read (dev, REG_USBCTL, vp)) < 0) { - dbg ("can't read USBCTL, %d", retval); - goto done; - } - usbctl = *vp; - nc_dump_usbctl (dev, usbctl); - - nc_register_write (dev, REG_USBCTL, - USBCTL_FLUSH_THIS | USBCTL_FLUSH_OTHER); - - if ((retval = nc_register_read (dev, REG_TTL, vp)) < 0) { - dbg ("can't read TTL, %d", retval); - goto done; - } - ttl = *vp; - // nc_dump_ttl (dev, ttl); - - nc_register_write (dev, REG_TTL, - MK_TTL (NC_READ_TTL_MS, TTL_OTHER (ttl)) ); - dbg ("%s: assigned TTL, %d ms", dev->net->name, NC_READ_TTL_MS); - - if (netif_msg_link (dev)) - devinfo (dev, "port %c, peer %sconnected", - (status & STATUS_PORT_A) ? 'A' : 'B', - (status & STATUS_CONN_OTHER) ? "" : "dis" - ); - retval = 0; - -done: - kfree (vp); - return retval; -} - -static int net1080_check_connect (struct usbnet *dev) -{ - int retval; - u16 status; - u16 *vp = kmalloc (sizeof (u16), GFP_KERNEL); - - if (!vp) - return -ENOMEM; - retval = nc_register_read (dev, REG_STATUS, vp); - status = *vp; - kfree (vp); - if (retval != 0) { - dbg ("%s net1080_check_conn read - %d", dev->net->name, retval); - return retval; - } - if ((status & STATUS_CONN_OTHER) != STATUS_CONN_OTHER) - return -ENOLINK; - return 0; -} - -static void nc_flush_complete (struct urb *urb, struct pt_regs *regs) -{ - kfree (urb->context); - usb_free_urb(urb); -} - -static void nc_ensure_sync (struct usbnet *dev) -{ - dev->frame_errors++; - if (dev->frame_errors > 5) { - struct urb *urb; - struct usb_ctrlrequest *req; - int status; - - /* Send a flush */ - urb = usb_alloc_urb (0, SLAB_ATOMIC); - if (!urb) - return; - - req = kmalloc (sizeof *req, GFP_ATOMIC); - if (!req) { - usb_free_urb (urb); - return; - } - - req->bRequestType = USB_DIR_OUT - | USB_TYPE_VENDOR - | USB_RECIP_DEVICE; - req->bRequest = REQUEST_REGISTER; - req->wValue = cpu_to_le16 (USBCTL_FLUSH_THIS - | USBCTL_FLUSH_OTHER); - req->wIndex = cpu_to_le16 (REG_USBCTL); - req->wLength = cpu_to_le16 (0); - - /* queue an async control request, we don't need - * to do anything when it finishes except clean up. - */ - usb_fill_control_urb (urb, dev->udev, - usb_sndctrlpipe (dev->udev, 0), - (unsigned char *) req, - NULL, 0, - nc_flush_complete, req); - status = usb_submit_urb (urb, GFP_ATOMIC); - if (status) { - kfree (req); - usb_free_urb (urb); - return; - } - - if (netif_msg_rx_err (dev)) - devdbg (dev, "flush net1080; too many framing errors"); - dev->frame_errors = 0; - } -} - -static int net1080_rx_fixup (struct usbnet *dev, struct sk_buff *skb) -{ - struct nc_header *header; - struct nc_trailer *trailer; - u16 hdr_len, packet_len; - - if (!(skb->len & 0x01) - || MIN_FRAMED > skb->len - || skb->len > FRAMED_SIZE (dev->net->mtu)) { - dev->stats.rx_frame_errors++; - dbg ("rx framesize %d range %d..%d mtu %d", skb->len, - (int)MIN_FRAMED, (int)FRAMED_SIZE (dev->net->mtu), - dev->net->mtu); - nc_ensure_sync (dev); - return 0; - } - - header = (struct nc_header *) skb->data; - hdr_len = le16_to_cpup (&header->hdr_len); - packet_len = le16_to_cpup (&header->packet_len); - if (FRAMED_SIZE (packet_len) > MAX_PACKET) { - dev->stats.rx_frame_errors++; - dbg ("packet too big, %d", packet_len); - nc_ensure_sync (dev); - return 0; - } else if (hdr_len < MIN_HEADER) { - dev->stats.rx_frame_errors++; - dbg ("header too short, %d", hdr_len); - nc_ensure_sync (dev); - return 0; - } else if (hdr_len > MIN_HEADER) { - // out of band data for us? - dbg ("header OOB, %d bytes", hdr_len - MIN_HEADER); - nc_ensure_sync (dev); - // switch (vendor/product ids) { ... } - } - skb_pull (skb, hdr_len); - - trailer = (struct nc_trailer *) - (skb->data + skb->len - sizeof *trailer); - skb_trim (skb, skb->len - sizeof *trailer); - - if ((packet_len & 0x01) == 0) { - if (skb->data [packet_len] != PAD_BYTE) { - dev->stats.rx_frame_errors++; - dbg ("bad pad"); - return 0; - } - skb_trim (skb, skb->len - 1); - } - if (skb->len != packet_len) { - dev->stats.rx_frame_errors++; - dbg ("bad packet len %d (expected %d)", - skb->len, packet_len); - nc_ensure_sync (dev); - return 0; - } - if (header->packet_id != get_unaligned (&trailer->packet_id)) { - dev->stats.rx_fifo_errors++; - dbg ("(2+ dropped) rx packet_id mismatch 0x%x 0x%x", - le16_to_cpu (header->packet_id), - le16_to_cpu (trailer->packet_id)); - return 0; - } -#if 0 - devdbg (dev, "frame hdr_len, - header->packet_len, header->packet_id); -#endif - dev->frame_errors = 0; - return 1; -} - -static struct sk_buff * -net1080_tx_fixup (struct usbnet *dev, struct sk_buff *skb, unsigned flags) -{ - int padlen; - struct sk_buff *skb2; - - padlen = ((skb->len + sizeof (struct nc_header) - + sizeof (struct nc_trailer)) & 0x01) ? 0 : 1; - if (!skb_cloned (skb)) { - int headroom = skb_headroom (skb); - int tailroom = skb_tailroom (skb); - - if ((padlen + sizeof (struct nc_trailer)) <= tailroom - && sizeof (struct nc_header) <= headroom) - /* There's enough head and tail room */ - return skb; - - if ((sizeof (struct nc_header) + padlen - + sizeof (struct nc_trailer)) < - (headroom + tailroom)) { - /* There's enough total room, so just readjust */ - skb->data = memmove (skb->head - + sizeof (struct nc_header), - skb->data, skb->len); - skb->tail = skb->data + skb->len; - return skb; - } - } - - /* Create a new skb to use with the correct size */ - skb2 = skb_copy_expand (skb, - sizeof (struct nc_header), - sizeof (struct nc_trailer) + padlen, - flags); - dev_kfree_skb_any (skb); - return skb2; -} - -static const struct driver_info net1080_info = { - .description = "NetChip TurboCONNECT", - .flags = FLAG_FRAMING_NC, - .reset = net1080_reset, - .check_connect =net1080_check_connect, - .rx_fixup = net1080_rx_fixup, - .tx_fixup = net1080_tx_fixup, -}; - -#endif /* CONFIG_USB_NET1080 */ - - - -#ifdef CONFIG_USB_PL2301 -#define HAVE_HARDWARE - -/*------------------------------------------------------------------------- - * - * Prolific PL-2301/PL-2302 driver ... http://www.prolifictech.com - * - * The protocol and handshaking used here should be bug-compatible - * with the Linux 2.2 "plusb" driver, by Deti Fliegl. - * - *-------------------------------------------------------------------------*/ - -/* - * Bits 0-4 can be used for software handshaking; they're set from - * one end, cleared from the other, "read" with the interrupt byte. - */ -#define PL_S_EN (1<<7) /* (feature only) suspend enable */ -/* reserved bit -- rx ready (6) ? */ -#define PL_TX_READY (1<<5) /* (interrupt only) transmit ready */ -#define PL_RESET_OUT (1<<4) /* reset output pipe */ -#define PL_RESET_IN (1<<3) /* reset input pipe */ -#define PL_TX_C (1<<2) /* transmission complete */ -#define PL_TX_REQ (1<<1) /* transmission received */ -#define PL_PEER_E (1<<0) /* peer exists */ - -static inline int -pl_vendor_req (struct usbnet *dev, u8 req, u8 val, u8 index) -{ - return usb_control_msg (dev->udev, - usb_rcvctrlpipe (dev->udev, 0), - req, - USB_DIR_IN | USB_TYPE_VENDOR | USB_RECIP_DEVICE, - val, index, - NULL, 0, - CONTROL_TIMEOUT_MS); -} - -static inline int -pl_clear_QuickLink_features (struct usbnet *dev, int val) -{ - return pl_vendor_req (dev, 1, (u8) val, 0); -} - -static inline int -pl_set_QuickLink_features (struct usbnet *dev, int val) -{ - return pl_vendor_req (dev, 3, (u8) val, 0); -} - -/*-------------------------------------------------------------------------*/ - -static int pl_reset (struct usbnet *dev) -{ - /* some units seem to need this reset, others reject it utterly. - * FIXME be more like "naplink" or windows drivers. - */ - (void) pl_set_QuickLink_features (dev, - PL_S_EN|PL_RESET_OUT|PL_RESET_IN|PL_PEER_E); - return 0; -} - -static const struct driver_info prolific_info = { - .description = "Prolific PL-2301/PL-2302", - .flags = FLAG_NO_SETINT, - /* some PL-2302 versions seem to fail usb_set_interface() */ - .reset = pl_reset, -}; - -#endif /* CONFIG_USB_PL2301 */ - - -#ifdef CONFIG_USB_KC2190 -#define HAVE_HARDWARE -static const struct driver_info kc2190_info = { - .description = "KC Technology KC-190", -}; -#endif /* CONFIG_USB_KC2190 */ - - -#ifdef CONFIG_USB_ARMLINUX -#define HAVE_HARDWARE - -/*------------------------------------------------------------------------- - * - * Intel's SA-1100 chip integrates basic USB support, and is used - * in PDAs like some iPaqs, the Yopy, some Zaurus models, and more. - * When they run Linux, arch/arm/mach-sa1100/usb-eth.c may be used to - * network using minimal USB framing data. - * - * This describes the driver currently in standard ARM Linux kernels. - * The Zaurus uses a different driver (see later). - * - * PXA25x and PXA210 use XScale cores (ARM v5TE) with better USB support - * and different USB endpoint numbering than the SA1100 devices. The - * mach-pxa/usb-eth.c driver re-uses the device ids from mach-sa1100 - * so we rely on the endpoint descriptors. - * - *-------------------------------------------------------------------------*/ - -static const struct driver_info linuxdev_info = { - .description = "Linux Device", - .check_connect = always_connected, -}; - -static const struct driver_info yopy_info = { - .description = "Yopy", - .check_connect = always_connected, -}; - -static const struct driver_info blob_info = { - .description = "Boot Loader OBject", - .check_connect = always_connected, -}; - -#endif /* CONFIG_USB_ARMLINUX */ - - -#ifdef CONFIG_USB_ZAURUS -#define HAVE_HARDWARE - -#include - -/*------------------------------------------------------------------------- - * - * Zaurus is also a SA-1110 based PDA, but one using a different driver - * (and framing) for its USB slave/gadget controller than the case above. - * - * For the current version of that driver, the main way that framing is - * nonstandard (also from perspective of the CDC ethernet model!) is a - * crc32, added to help detect when some sa1100 usb-to-memory DMA errata - * haven't been fully worked around. Also, all Zaurii use the same - * default Ethernet address. - * - * PXA based models use the same framing, and also can't implement - * set_interface properly. - * - * All known Zaurii lie about their standards conformance. Most lie by - * saying they support CDC Ethernet. Some lie and say they support CDC - * MDLM (as if for access to cell phone modems). Someone, please beat - * on Sharp (and other such vendors) for a while with a cluestick. - * - *-------------------------------------------------------------------------*/ - -static struct sk_buff * -zaurus_tx_fixup (struct usbnet *dev, struct sk_buff *skb, unsigned flags) -{ - int padlen; - struct sk_buff *skb2; - - padlen = 2; - if (!skb_cloned (skb)) { - int tailroom = skb_tailroom (skb); - if ((padlen + 4) <= tailroom) - goto done; + status = e; + } else { + if (!out) + out = e; + } + } + if (in && out) + break; } - skb2 = skb_copy_expand (skb, 0, 4 + padlen, flags); - dev_kfree_skb_any (skb); - skb = skb2; - if (skb) { - u32 fcs; -done: - fcs = crc32_le (~0, skb->data, skb->len); - fcs = ~fcs; + if (!alt || !in || !out) + return -EINVAL; - *skb_put (skb, 1) = fcs & 0xff; - *skb_put (skb, 1) = (fcs>> 8) & 0xff; - *skb_put (skb, 1) = (fcs>>16) & 0xff; - *skb_put (skb, 1) = (fcs>>24) & 0xff; + if (alt->desc.bAlternateSetting != 0 + || !(dev->driver_info->flags & FLAG_NO_SETINT)) { + tmp = usb_set_interface (dev->udev, alt->desc.bInterfaceNumber, + alt->desc.bAlternateSetting); + if (tmp < 0) + return tmp; } - return skb; + + dev->in = usb_rcvbulkpipe (dev->udev, + in->desc.bEndpointAddress & USB_ENDPOINT_NUMBER_MASK); + dev->out = usb_sndbulkpipe (dev->udev, + out->desc.bEndpointAddress & USB_ENDPOINT_NUMBER_MASK); + dev->status = status; + return 0; } +EXPORT_SYMBOL_GPL(usbnet_get_endpoints); -static const struct driver_info zaurus_sl5x00_info = { - .description = "Sharp Zaurus SL-5x00", - .flags = FLAG_FRAMING_Z, - .check_connect = always_connected, - .bind = generic_cdc_bind, - .unbind = cdc_unbind, - .tx_fixup = zaurus_tx_fixup, -}; -#define ZAURUS_STRONGARM_INFO ((unsigned long)&zaurus_sl5x00_info) - -static const struct driver_info zaurus_pxa_info = { - .description = "Sharp Zaurus, PXA-2xx based", - .flags = FLAG_FRAMING_Z, - .check_connect = always_connected, - .bind = generic_cdc_bind, - .unbind = cdc_unbind, - .tx_fixup = zaurus_tx_fixup, -}; -#define ZAURUS_PXA_INFO ((unsigned long)&zaurus_pxa_info) - -static const struct driver_info olympus_mxl_info = { - .description = "Olympus R1000", - .flags = FLAG_FRAMING_Z, - .check_connect = always_connected, - .bind = generic_cdc_bind, - .unbind = cdc_unbind, - .tx_fixup = zaurus_tx_fixup, -}; -#define OLYMPUS_MXL_INFO ((unsigned long)&olympus_mxl_info) - - -/* Some more recent products using Lineo/Belcarra code will wrongly claim - * CDC MDLM conformance. They aren't conformant: data endpoints live - * in the control interface, there's no data interface, and it's not used - * to talk to a cell phone radio. But at least we can detect these two - * pseudo-classes, rather than growing this product list with entries for - * each new nonconformant product (sigh). - */ -static const u8 safe_guid[16] = { - 0x5d, 0x34, 0xcf, 0x66, 0x11, 0x18, 0x11, 0xd6, - 0xa2, 0x1a, 0x00, 0x01, 0x02, 0xca, 0x9a, 0x7f, -}; -static const u8 blan_guid[16] = { - 0x74, 0xf0, 0x3d, 0xbd, 0x1e, 0xc1, 0x44, 0x70, - 0xa3, 0x67, 0x71, 0x34, 0xc9, 0xf5, 0x54, 0x37, -}; +static void intr_complete (struct urb *urb); -static int blan_mdlm_bind (struct usbnet *dev, struct usb_interface *intf) +static int init_status (struct usbnet *dev, struct usb_interface *intf) { - u8 *buf = intf->cur_altsetting->extra; - int len = intf->cur_altsetting->extralen; - struct usb_cdc_mdlm_desc *desc = NULL; - struct usb_cdc_mdlm_detail_desc *detail = NULL; + char *buf = NULL; + unsigned pipe = 0; + unsigned maxp; + unsigned period; - while (len > 3) { - if (buf [1] != USB_DT_CS_INTERFACE) - goto next_desc; + if (!dev->driver_info->status) + return 0; - /* use bDescriptorSubType, and just verify that we get a - * "BLAN" (or "SAFE") descriptor. - */ - switch (buf [2]) { - case USB_CDC_MDLM_TYPE: - if (desc) { - dev_dbg (&intf->dev, "extra MDLM\n"); - goto bad_desc; - } - desc = (void *) buf; - if (desc->bLength != sizeof *desc) { - dev_dbg (&intf->dev, "MDLM len %u\n", - desc->bLength); - goto bad_desc; - } - /* expect bcdVersion 1.0, ignore */ - if (memcmp(&desc->bGUID, blan_guid, 16) - && memcmp(&desc->bGUID, safe_guid, 16) ) { - /* hey, this one might _really_ be MDLM! */ - dev_dbg (&intf->dev, "MDLM guid\n"); - goto bad_desc; - } - break; - case USB_CDC_MDLM_DETAIL_TYPE: - if (detail) { - dev_dbg (&intf->dev, "extra MDLM detail\n"); - goto bad_desc; - } - detail = (void *) buf; - switch (detail->bGuidDescriptorType) { - case 0: /* "SAFE" */ - if (detail->bLength != (sizeof *detail + 2)) - goto bad_detail; - break; - case 1: /* "BLAN" */ - if (detail->bLength != (sizeof *detail + 3)) - goto bad_detail; - break; - default: - goto bad_detail; - } + pipe = usb_rcvintpipe (dev->udev, + dev->status->desc.bEndpointAddress + & USB_ENDPOINT_NUMBER_MASK); + maxp = usb_maxpacket (dev->udev, pipe, 0); - /* assuming we either noticed BLAN already, or will - * find it soon, there are some data bytes here: - * - bmNetworkCapabilities (unused) - * - bmDataCapabilities (bits, see below) - * - bPad (ignored, for PADAFTER -- BLAN-only) - * bits are: - * - 0x01 -- Zaurus framing (add CRC) - * - 0x02 -- PADBEFORE (CRC includes some padding) - * - 0x04 -- PADAFTER (some padding after CRC) - * - 0x08 -- "fermat" packet mangling (for hw bugs) - * the PADBEFORE appears not to matter; we interop - * with devices that use it and those that don't. - */ - if ((detail->bDetailData[1] & ~02) != 0x01) { - /* bmDataCapabilites == 0 would be fine too, - * but framing is minidriver-coupled for now. - */ -bad_detail: - dev_dbg (&intf->dev, - "bad MDLM detail, %d %d %d\n", - detail->bLength, - detail->bDetailData[0], - detail->bDetailData[2]); - goto bad_desc; - } - break; - } -next_desc: - len -= buf [0]; /* bLength */ - buf += buf [0]; - } + /* avoid 1 msec chatter: min 8 msec poll rate */ + period = max ((int) dev->status->desc.bInterval, + (dev->udev->speed == USB_SPEED_HIGH) ? 7 : 3); - if (!desc || !detail) { - dev_dbg (&intf->dev, "missing cdc mdlm %s%sdescriptor\n", - desc ? "" : "func ", - detail ? "" : "detail "); - goto bad_desc; + buf = kmalloc (maxp, SLAB_KERNEL); + if (buf) { + dev->interrupt = usb_alloc_urb (0, SLAB_KERNEL); + if (!dev->interrupt) { + kfree (buf); + return -ENOMEM; + } else { + usb_fill_int_urb(dev->interrupt, dev->udev, pipe, + buf, maxp, intr_complete, dev, period); + dev_dbg(&intf->dev, + "status ep%din, %d bytes period %d\n", + usb_pipeendpoint(pipe), maxp, period); + } } - - /* There's probably a CDC Ethernet descriptor there, but we can't - * rely on the Ethernet address it provides since not all vendors - * bother to make it unique. Likewise there's no point in tracking - * of the CDC event notifications. - */ - return get_endpoints (dev, intf); - -bad_desc: - dev_info (&dev->udev->dev, "unsupported MDLM descriptors\n"); - return -ENODEV; + return 0; } -static const struct driver_info bogus_mdlm_info = { - .description = "pseudo-MDLM (BLAN) device", - .flags = FLAG_FRAMING_Z, - .check_connect = always_connected, - .tx_fixup = zaurus_tx_fixup, - .bind = blan_mdlm_bind, -}; - -#else +/* Passes this packet up the stack, updating its accounting. + * Some link protocols batch packets, so their rx_fixup paths + * can return clones as well as just modify the original skb. + */ +void usbnet_skb_return (struct usbnet *dev, struct sk_buff *skb) +{ + int status; -/* blacklist all those devices */ -#define ZAURUS_STRONGARM_INFO 0 -#define ZAURUS_PXA_INFO 0 -#define OLYMPUS_MXL_INFO 0 + skb->dev = dev->net; + skb->protocol = eth_type_trans (skb, dev->net); + dev->stats.rx_packets++; + dev->stats.rx_bytes += skb->len; -#endif + if (netif_msg_rx_status (dev)) + devdbg (dev, "< rx, len %zu, type 0x%x", + skb->len + sizeof (struct ethhdr), skb->protocol); + memset (skb->cb, 0, sizeof (struct skb_data)); + status = netif_rx (skb); + if (status != NET_RX_SUCCESS && netif_msg_rx_err (dev)) + devdbg (dev, "netif_rx status %d", status); +} +EXPORT_SYMBOL_GPL(usbnet_skb_return); /*------------------------------------------------------------------------- @@ -2868,24 +229,24 @@ static const struct driver_info bogus_mdlm_info = { static int usbnet_change_mtu (struct net_device *net, int new_mtu) { struct usbnet *dev = netdev_priv(net); + int ll_mtu = new_mtu + net->hard_header_len; + int old_hard_mtu = dev->hard_mtu; + int old_rx_urb_size = dev->rx_urb_size; - if (new_mtu <= MIN_PACKET || new_mtu > MAX_PACKET) - return -EINVAL; -#ifdef CONFIG_USB_NET1080 - if (((dev->driver_info->flags) & FLAG_FRAMING_NC)) { - if (FRAMED_SIZE (new_mtu) > MAX_PACKET) - return -EINVAL; - } -#endif -#ifdef CONFIG_USB_GENESYS - if (((dev->driver_info->flags) & FLAG_FRAMING_GL) - && new_mtu > GL_MAX_PACKET_LEN) + if (new_mtu <= 0) return -EINVAL; -#endif // no second zero-length packet read wanted after mtu-sized packets - if (((new_mtu + sizeof (struct ethhdr)) % dev->maxpacket) == 0) + if ((ll_mtu % dev->maxpacket) == 0) return -EDOM; net->mtu = new_mtu; + + dev->hard_mtu = net->mtu + net->hard_header_len; + if (dev->rx_urb_size == old_hard_mtu) { + dev->rx_urb_size = dev->hard_mtu; + if (dev->rx_urb_size > old_rx_urb_size) + usbnet_unlink_rx_urbs(dev); + } + return 0; } @@ -2922,7 +283,7 @@ static void defer_bh(struct usbnet *dev, struct sk_buff *skb, struct sk_buff_hea * NOTE: annoying asymmetry: if it's active, schedule_work() fails, * but tasklet_schedule() doesn't. hope the failure is rare. */ -static void defer_kevent (struct usbnet *dev, int work) +void usbnet_defer_kevent (struct usbnet *dev, int work) { set_bit (work, &dev->flags); if (!schedule_work (&dev->kevent)) @@ -2930,50 +291,24 @@ static void defer_kevent (struct usbnet *dev, int work) else devdbg (dev, "kevent %d scheduled", work); } +EXPORT_SYMBOL_GPL(usbnet_defer_kevent); /*-------------------------------------------------------------------------*/ -static void rx_complete (struct urb *urb, struct pt_regs *regs); +static void rx_complete (struct urb *urb); -static void rx_submit (struct usbnet *dev, struct urb *urb, unsigned flags) +static void rx_submit (struct usbnet *dev, struct urb *urb, gfp_t flags) { struct sk_buff *skb; struct skb_data *entry; int retval = 0; unsigned long lockflags; - size_t size; - -#ifdef CONFIG_USB_NET1080 - if (dev->driver_info->flags & FLAG_FRAMING_NC) - size = FRAMED_SIZE (dev->net->mtu); - else -#endif -#ifdef CONFIG_USB_GENESYS - if (dev->driver_info->flags & FLAG_FRAMING_GL) - size = GL_RCV_BUF_SIZE; - else -#endif -#ifdef CONFIG_USB_ZAURUS - if (dev->driver_info->flags & FLAG_FRAMING_Z) - size = 6 + (sizeof (struct ethhdr) + dev->net->mtu); - else -#endif -#ifdef CONFIG_USB_RNDIS - if (dev->driver_info->flags & FLAG_FRAMING_RN) - size = RNDIS_MAX_TRANSFER; - else -#endif -#ifdef CONFIG_USB_AX8817X - if (dev->driver_info->flags & FLAG_FRAMING_AX) - size = 2048; - else -#endif - size = (sizeof (struct ethhdr) + dev->net->mtu); + size_t size = dev->rx_urb_size; if ((skb = alloc_skb (size + NET_IP_ALIGN, flags)) == NULL) { if (netif_msg_rx_err (dev)) devdbg (dev, "no rx skb"); - defer_kevent (dev, EVENT_RX_MEMORY); + usbnet_defer_kevent (dev, EVENT_RX_MEMORY); usb_free_urb (urb); return; } @@ -2995,10 +330,10 @@ static void rx_submit (struct usbnet *dev, struct urb *urb, unsigned flags) && !test_bit (EVENT_RX_HALT, &dev->flags)) { switch (retval = usb_submit_urb (urb, GFP_ATOMIC)){ case -EPIPE: - defer_kevent (dev, EVENT_RX_HALT); + usbnet_defer_kevent (dev, EVENT_RX_HALT); break; case -ENOMEM: - defer_kevent (dev, EVENT_RX_MEMORY); + usbnet_defer_kevent (dev, EVENT_RX_MEMORY); break; case -ENODEV: if (netif_msg_ifdown (dev)) @@ -3036,7 +371,7 @@ static inline void rx_process (struct usbnet *dev, struct sk_buff *skb) // else network stack removes extra byte if we forced a short packet if (skb->len) - skb_return (dev, skb); + usbnet_skb_return (dev, skb); else { if (netif_msg_rx_err (dev)) devdbg (dev, "drop"); @@ -3048,7 +383,7 @@ error: /*-------------------------------------------------------------------------*/ -static void rx_complete (struct urb *urb, struct pt_regs *regs) +static void rx_complete (struct urb *urb) { struct sk_buff *skb = (struct sk_buff *) urb->context; struct skb_data *entry = (struct skb_data *) skb->cb; @@ -3062,7 +397,7 @@ static void rx_complete (struct urb *urb, struct pt_regs *regs) switch (urb_status) { // success case 0: - if (MIN_PACKET > skb->len || skb->len > MAX_PACKET) { + if (skb->len < dev->net->hard_header_len) { entry->state = rx_cleanup; dev->stats.rx_errors++; dev->stats.rx_length_errors++; @@ -3077,7 +412,7 @@ static void rx_complete (struct urb *urb, struct pt_regs *regs) // storm, recovering as needed. case -EPIPE: dev->stats.rx_errors++; - defer_kevent (dev, EVENT_RX_HALT); + usbnet_defer_kevent (dev, EVENT_RX_HALT); // FALLTHROUGH // software-driven interface shutdown @@ -3090,9 +425,9 @@ static void rx_complete (struct urb *urb, struct pt_regs *regs) // we get controller i/o faults during khubd disconnect() delays. // throttle down resubmits, to avoid log floods; just temporarily, // so we still recover when the fault isn't a khubd delay. - case -EPROTO: // ehci - case -ETIMEDOUT: // ohci - case -EILSEQ: // uhci + case -EPROTO: + case -ETIME: + case -EILSEQ: dev->stats.rx_errors++; if (!timer_pending (&dev->delay)) { mod_timer (&dev->delay, jiffies + THROTTLE_JIFFIES); @@ -3132,7 +467,7 @@ block: devdbg (dev, "no read resubmitted"); } -static void intr_complete (struct urb *urb, struct pt_regs *regs) +static void intr_complete (struct urb *urb) { struct usbnet *dev = urb->context; int status = urb->status; @@ -3199,6 +534,17 @@ static int unlink_urbs (struct usbnet *dev, struct sk_buff_head *q) return count; } +// Flush all pending rx urbs +// minidrivers may need to do this when the MTU changes + +void usbnet_unlink_rx_urbs(struct usbnet *dev) +{ + if (netif_running(dev->net)) { + (void) unlink_urbs (dev, &dev->rxq); + tasklet_schedule(&dev->bh); + } +} +EXPORT_SYMBOL_GPL(usbnet_unlink_rx_urbs); /*-------------------------------------------------------------------------*/ @@ -3208,7 +554,7 @@ static int usbnet_stop (struct net_device *net) { struct usbnet *dev = netdev_priv(net); int temp; - DECLARE_WAIT_QUEUE_HEAD (unlink_wakeup); + DECLARE_WAIT_QUEUE_HEAD_ONSTACK (unlink_wakeup); DECLARE_WAITQUEUE (wait, current); netif_stop_queue (net); @@ -3307,7 +653,7 @@ static int usbnet_open (struct net_device *net) devinfo (dev, "open: enable queueing " "(rx %d, tx %d) mtu %d %s framing", - RX_QLEN (dev), TX_QLEN (dev), dev->net->mtu, + (int)RX_QLEN (dev), (int)TX_QLEN (dev), dev->net->mtu, framing); } @@ -3319,55 +665,114 @@ done: /*-------------------------------------------------------------------------*/ -static void usbnet_get_drvinfo (struct net_device *net, struct ethtool_drvinfo *info) +/* ethtool methods; minidrivers may need to add some more, but + * they'll probably want to use this base set. + */ + +#if defined(CONFIG_MII) || defined(CONFIG_MII_MODULE) +#define HAVE_MII + +int usbnet_get_settings (struct net_device *net, struct ethtool_cmd *cmd) { struct usbnet *dev = netdev_priv(net); - strncpy (info->driver, driver_name, sizeof info->driver); - strncpy (info->version, DRIVER_VERSION, sizeof info->version); - strncpy (info->fw_version, dev->driver_info->description, - sizeof info->fw_version); - usb_make_path (dev->udev, info->bus_info, sizeof info->bus_info); + if (!dev->mii.mdio_read) + return -EOPNOTSUPP; + + return mii_ethtool_gset(&dev->mii, cmd); +} +EXPORT_SYMBOL_GPL(usbnet_get_settings); + +int usbnet_set_settings (struct net_device *net, struct ethtool_cmd *cmd) +{ + struct usbnet *dev = netdev_priv(net); + int retval; + + if (!dev->mii.mdio_write) + return -EOPNOTSUPP; + + retval = mii_ethtool_sset(&dev->mii, cmd); + + /* link speed/duplex might have changed */ + if (dev->driver_info->link_reset) + dev->driver_info->link_reset(dev); + + return retval; + } +EXPORT_SYMBOL_GPL(usbnet_set_settings); -static u32 usbnet_get_link (struct net_device *net) +u32 usbnet_get_link (struct net_device *net) { struct usbnet *dev = netdev_priv(net); - /* If a check_connect is defined, return it's results */ + /* If a check_connect is defined, return its result */ if (dev->driver_info->check_connect) return dev->driver_info->check_connect (dev) == 0; - /* Otherwise, we're up to avoid breaking scripts */ + /* if the device has mii operations, use those */ + if (dev->mii.mdio_read) + return mii_link_ok(&dev->mii); + + /* Otherwise, say we're up (to avoid breaking scripts) */ return 1; } +EXPORT_SYMBOL_GPL(usbnet_get_link); -static u32 usbnet_get_msglevel (struct net_device *net) +int usbnet_nway_reset(struct net_device *net) { struct usbnet *dev = netdev_priv(net); - return dev->msg_enable; + if (!dev->mii.mdio_write) + return -EOPNOTSUPP; + + return mii_nway_restart(&dev->mii); } +EXPORT_SYMBOL_GPL(usbnet_nway_reset); + +#endif /* HAVE_MII */ -static void usbnet_set_msglevel (struct net_device *net, u32 level) +void usbnet_get_drvinfo (struct net_device *net, struct ethtool_drvinfo *info) { struct usbnet *dev = netdev_priv(net); - dev->msg_enable = level; + /* REVISIT don't always return "usbnet" */ + strncpy (info->driver, driver_name, sizeof info->driver); + strncpy (info->version, DRIVER_VERSION, sizeof info->version); + strncpy (info->fw_version, dev->driver_info->description, + sizeof info->fw_version); + usb_make_path (dev->udev, info->bus_info, sizeof info->bus_info); } +EXPORT_SYMBOL_GPL(usbnet_get_drvinfo); -static int usbnet_ioctl (struct net_device *net, struct ifreq *rq, int cmd) +u32 usbnet_get_msglevel (struct net_device *net) { -#ifdef NEED_MII - { struct usbnet *dev = netdev_priv(net); - if (dev->mii.mdio_read != NULL && dev->mii.mdio_write != NULL) - return generic_mii_ioctl(&dev->mii, if_mii(rq), cmd, NULL); - } -#endif - return -EOPNOTSUPP; + return dev->msg_enable; +} +EXPORT_SYMBOL_GPL(usbnet_get_msglevel); + +void usbnet_set_msglevel (struct net_device *net, u32 level) +{ + struct usbnet *dev = netdev_priv(net); + + dev->msg_enable = level; } +EXPORT_SYMBOL_GPL(usbnet_set_msglevel); + +/* drivers may override default ethtool_ops in their bind() routine */ +static struct ethtool_ops usbnet_ethtool_ops = { +#ifdef HAVE_MII + .get_settings = usbnet_get_settings, + .set_settings = usbnet_set_settings, + .get_link = usbnet_get_link, + .nway_reset = usbnet_nway_reset, +#endif + .get_drvinfo = usbnet_get_drvinfo, + .get_msglevel = usbnet_get_msglevel, + .set_msglevel = usbnet_set_msglevel, +}; /*-------------------------------------------------------------------------*/ @@ -3377,28 +782,34 @@ static int usbnet_ioctl (struct net_device *net, struct ifreq *rq, int cmd) * especially now that control transfers can be queued. */ static void -kevent (void *data) +kevent (struct work_struct *work) { - struct usbnet *dev = data; + struct usbnet *dev = + container_of(work, struct usbnet, kevent); int status; /* usb_clear_halt() needs a thread context */ if (test_bit (EVENT_TX_HALT, &dev->flags)) { unlink_urbs (dev, &dev->txq); status = usb_clear_halt (dev->udev, dev->out); - if (status < 0 && status != -EPIPE) { + if (status < 0 + && status != -EPIPE + && status != -ESHUTDOWN) { if (netif_msg_tx_err (dev)) deverr (dev, "can't clear tx halt, status %d", status); } else { clear_bit (EVENT_TX_HALT, &dev->flags); - netif_wake_queue (dev->net); + if (status != -ESHUTDOWN) + netif_wake_queue (dev->net); } } if (test_bit (EVENT_RX_HALT, &dev->flags)) { unlink_urbs (dev, &dev->rxq); status = usb_clear_halt (dev->udev, dev->in); - if (status < 0 && status != -EPIPE) { + if (status < 0 + && status != -EPIPE + && status != -ESHUTDOWN) { if (netif_msg_rx_err (dev)) deverr (dev, "can't clear rx halt, status %d", status); @@ -3443,7 +854,7 @@ kevent (void *data) /*-------------------------------------------------------------------------*/ -static void tx_complete (struct urb *urb, struct pt_regs *regs) +static void tx_complete (struct urb *urb) { struct sk_buff *skb = (struct sk_buff *) urb->context; struct skb_data *entry = (struct skb_data *) skb->cb; @@ -3457,7 +868,7 @@ static void tx_complete (struct urb *urb, struct pt_regs *regs) switch (urb->status) { case -EPIPE: - defer_kevent (dev, EVENT_TX_HALT); + usbnet_defer_kevent (dev, EVENT_TX_HALT); break; /* software-driven interface shutdown */ @@ -3467,9 +878,9 @@ static void tx_complete (struct urb *urb, struct pt_regs *regs) // like rx, tx gets controller i/o faults during khubd delays // and so it uses the same throttling mechanism. - case -EPROTO: // ehci - case -ETIMEDOUT: // ohci - case -EILSEQ: // uhci + case -EPROTO: + case -ETIME: + case -EILSEQ: if (!timer_pending (&dev->delay)) { mod_timer (&dev->delay, jiffies + THROTTLE_JIFFIES); @@ -3514,10 +925,6 @@ static int usbnet_start_xmit (struct sk_buff *skb, struct net_device *net) struct skb_data *entry; struct driver_info *info = dev->driver_info; unsigned long flags; -#ifdef CONFIG_USB_NET1080 - struct nc_header *header = NULL; - struct nc_trailer *trailer = NULL; -#endif /* CONFIG_USB_NET1080 */ // some devices want funky USB-level framing, for // win32 driver (usually) and/or hardware quirks @@ -3543,21 +950,6 @@ static int usbnet_start_xmit (struct sk_buff *skb, struct net_device *net) entry->state = tx_start; entry->length = length; - // FIXME: reorganize a bit, so that fixup() fills out NetChip - // framing too. (Packet ID update needs the spinlock...) - // [ BETTER: we already own net->xmit_lock, that's enough ] - -#ifdef CONFIG_USB_NET1080 - if (info->flags & FLAG_FRAMING_NC) { - header = (struct nc_header *) skb_push (skb, sizeof *header); - header->hdr_len = cpu_to_le16 (sizeof (*header)); - header->packet_len = cpu_to_le16 (length); - if (!((skb->len + sizeof *trailer) & 0x01)) - *skb_put (skb, 1) = PAD_BYTE; - trailer = (struct nc_trailer *) skb_put (skb, sizeof *trailer); - } -#endif /* CONFIG_USB_NET1080 */ - usb_fill_bulk_urb (urb, dev->udev, dev->out, skb->data, skb->len, tx_complete, skb); @@ -3572,22 +964,10 @@ static int usbnet_start_xmit (struct sk_buff *skb, struct net_device *net) spin_lock_irqsave (&dev->txq.lock, flags); -#ifdef CONFIG_USB_NET1080 - if (info->flags & FLAG_FRAMING_NC) { - header->packet_id = cpu_to_le16 ((u16)dev->dev_packet_id++); - put_unaligned (header->packet_id, &trailer->packet_id); -#if 0 - devdbg (dev, "frame >tx h %d p %d id %d", - header->hdr_len, header->packet_len, - header->packet_id); -#endif - } -#endif /* CONFIG_USB_NET1080 */ - switch ((retval = usb_submit_urb (urb, GFP_ATOMIC))) { case -EPIPE: netif_stop_queue (net); - defer_kevent (dev, EVENT_TX_HALT); + usbnet_defer_kevent (dev, EVENT_TX_HALT); break; default: if (netif_msg_tx_err (dev)) @@ -3690,7 +1070,7 @@ static void usbnet_bh (unsigned long param) // precondition: never called in_interrupt -static void usbnet_disconnect (struct usb_interface *intf) +void usbnet_disconnect (struct usb_interface *intf) { struct usbnet *dev; struct usb_device *xdev; @@ -3704,7 +1084,8 @@ static void usbnet_disconnect (struct usb_interface *intf) xdev = interface_to_usbdev (intf); if (netif_msg_probe (dev)) - devinfo (dev, "unregister usbnet usb-%s-%s, %s", + devinfo (dev, "unregister '%s' usb-%s-%s, %s", + intf->dev.driver->name, xdev->bus->bus_name, xdev->devpath, dev->driver_info->description); @@ -3720,15 +1101,14 @@ static void usbnet_disconnect (struct usb_interface *intf) free_netdev(net); usb_put_dev (xdev); } +EXPORT_SYMBOL_GPL(usbnet_disconnect); /*-------------------------------------------------------------------------*/ -static struct ethtool_ops usbnet_ethtool_ops; - // precondition: never called in_interrupt -static int +int usbnet_probe (struct usb_interface *udev, const struct usb_device_id *prod) { struct usbnet *dev; @@ -3767,16 +1147,21 @@ usbnet_probe (struct usb_interface *udev, const struct usb_device_id *prod) skb_queue_head_init (&dev->done); dev->bh.func = usbnet_bh; dev->bh.data = (unsigned long) dev; - INIT_WORK (&dev->kevent, kevent, dev); + INIT_WORK (&dev->kevent, kevent); dev->delay.function = usbnet_bh; dev->delay.data = (unsigned long) dev; init_timer (&dev->delay); + mutex_init (&dev->phy_mutex); SET_MODULE_OWNER (net); dev->net = net; strcpy (net->name, "usb%d"); memcpy (net->dev_addr, node_id, sizeof node_id); + /* rx and tx sides can use different message sizes; + * bind() should set rx_urb_size in that case. + */ + dev->hard_mtu = net->mtu + net->hard_header_len; #if 0 // dma_supported() is deeply broken on almost all architectures // possible with some EHCI controllers @@ -3791,7 +1176,6 @@ usbnet_probe (struct usb_interface *udev, const struct usb_device_id *prod) net->stop = usbnet_stop; net->watchdog_timeo = TX_TIMEOUT_JIFFIES; net->tx_timeout = usbnet_tx_timeout; - net->do_ioctl = usbnet_ioctl; net->ethtool_ops = &usbnet_ethtool_ops; // allow device-specific bind/init procedures @@ -3804,8 +1188,12 @@ usbnet_probe (struct usb_interface *udev, const struct usb_device_id *prod) if ((dev->driver_info->flags & FLAG_ETHER) != 0 && (net->dev_addr [0] & 0x02) == 0) strcpy (net->name, "eth%d"); - } else if (!info->in || info->out) - status = get_endpoints (dev, udev); + + /* maybe the remote can't receive an Ethernet MTU */ + if (net->mtu > (dev->hard_mtu - net->hard_header_len)) + net->mtu = dev->hard_mtu - net->hard_header_len; + } else if (!info->in || !info->out) + status = usbnet_get_endpoints (dev, udev); else { dev->in = usb_rcvbulkpipe (xdev, info->in); dev->out = usb_sndbulkpipe (xdev, info->out); @@ -3817,12 +1205,13 @@ usbnet_probe (struct usb_interface *udev, const struct usb_device_id *prod) status = 0; } - if (status == 0 && dev->status) status = init_status (dev, udev); if (status < 0) goto out1; + if (!dev->rx_urb_size) + dev->rx_urb_size = dev->hard_mtu; dev->maxpacket = usb_maxpacket (dev->udev, dev->out, 1); SET_NETDEV_DEV(net, &udev->dev); @@ -3830,8 +1219,9 @@ usbnet_probe (struct usb_interface *udev, const struct usb_device_id *prod) if (status) goto out3; if (netif_msg_probe (dev)) - devinfo (dev, "register usbnet at usb-%s-%s, %s, " + devinfo (dev, "register '%s' at usb-%s-%s, %s, " "%02x:%02x:%02x:%02x:%02x:%02x", + udev->dev.driver->name, xdev->bus->bus_name, xdev->devpath, dev->driver_info->description, net->dev_addr [0], net->dev_addr [1], @@ -3855,12 +1245,15 @@ out: usb_put_dev(xdev); return status; } +EXPORT_SYMBOL_GPL(usbnet_probe); /*-------------------------------------------------------------------------*/ -#ifdef CONFIG_PM +/* FIXME these suspend/resume methods assume non-CDC style + * devices, with only one interface. + */ -static int usbnet_suspend (struct usb_interface *intf, pm_message_t message) +int usbnet_suspend (struct usb_interface *intf, pm_message_t message) { struct usbnet *dev = usb_get_intfdata(intf); @@ -3870,370 +1263,39 @@ static int usbnet_suspend (struct usb_interface *intf, pm_message_t message) netif_device_detach (dev->net); (void) unlink_urbs (dev, &dev->rxq); (void) unlink_urbs (dev, &dev->txq); - intf->dev.power.power_state = PMSG_SUSPEND; return 0; } +EXPORT_SYMBOL_GPL(usbnet_suspend); -static int usbnet_resume (struct usb_interface *intf) +int usbnet_resume (struct usb_interface *intf) { struct usbnet *dev = usb_get_intfdata(intf); - intf->dev.power.power_state = PMSG_ON; netif_device_attach (dev->net); tasklet_schedule (&dev->bh); return 0; } +EXPORT_SYMBOL_GPL(usbnet_resume); -#else /* !CONFIG_PM */ - -#define usbnet_suspend NULL -#define usbnet_resume NULL - -#endif /* CONFIG_PM */ - -/*-------------------------------------------------------------------------*/ - -#ifndef HAVE_HARDWARE -#error You need to configure some hardware for this driver -#endif - -/* - * chip vendor names won't normally be on the cables, and - * may not be on the device. - */ - -static const struct usb_device_id products [] = { - -#ifdef CONFIG_USB_ALI_M5632 -{ - USB_DEVICE (0x0402, 0x5632), // ALi defaults - .driver_info = (unsigned long) &ali_m5632_info, -}, -#endif - -#ifdef CONFIG_USB_AN2720 -{ - USB_DEVICE (0x0547, 0x2720), // AnchorChips defaults - .driver_info = (unsigned long) &an2720_info, -}, { - USB_DEVICE (0x0547, 0x2727), // Xircom PGUNET - .driver_info = (unsigned long) &an2720_info, -}, -#endif - -#ifdef CONFIG_USB_BELKIN -{ - USB_DEVICE (0x050d, 0x0004), // Belkin - .driver_info = (unsigned long) &belkin_info, -}, { - USB_DEVICE (0x056c, 0x8100), // eTEK - .driver_info = (unsigned long) &belkin_info, -}, { - USB_DEVICE (0x0525, 0x9901), // Advance USBNET (eTEK) - .driver_info = (unsigned long) &belkin_info, -}, -#endif - -#ifdef CONFIG_USB_AX8817X -{ - // Linksys USB200M - USB_DEVICE (0x077b, 0x2226), - .driver_info = (unsigned long) &ax8817x_info, -}, { - // Netgear FA120 - USB_DEVICE (0x0846, 0x1040), - .driver_info = (unsigned long) &netgear_fa120_info, -}, { - // DLink DUB-E100 - USB_DEVICE (0x2001, 0x1a00), - .driver_info = (unsigned long) &dlink_dub_e100_info, -}, { - // Intellinet, ST Lab USB Ethernet - USB_DEVICE (0x0b95, 0x1720), - .driver_info = (unsigned long) &ax8817x_info, -}, { - // Hawking UF200, TrendNet TU2-ET100 - USB_DEVICE (0x07b8, 0x420a), - .driver_info = (unsigned long) &hawking_uf200_info, -}, { - // Billionton Systems, USB2AR - USB_DEVICE (0x08dd, 0x90ff), - .driver_info = (unsigned long) &ax8817x_info, -}, { - // ATEN UC210T - USB_DEVICE (0x0557, 0x2009), - .driver_info = (unsigned long) &ax8817x_info, -}, { - // Buffalo LUA-U2-KTX - USB_DEVICE (0x0411, 0x003d), - .driver_info = (unsigned long) &ax8817x_info, -}, { - // Sitecom LN-029 "USB 2.0 10/100 Ethernet adapter" - USB_DEVICE (0x6189, 0x182d), - .driver_info = (unsigned long) &ax8817x_info, -}, { - // corega FEther USB2-TX - USB_DEVICE (0x07aa, 0x0017), - .driver_info = (unsigned long) &ax8817x_info, -}, { - // Surecom EP-1427X-2 - USB_DEVICE (0x1189, 0x0893), - .driver_info = (unsigned long) &ax8817x_info, -}, { - // goodway corp usb gwusb2e - USB_DEVICE (0x1631, 0x6200), - .driver_info = (unsigned long) &ax8817x_info, -}, { - // ASIX AX88772 10/100 - USB_DEVICE (0x0b95, 0x7720), - .driver_info = (unsigned long) &ax88772_info, -}, -#endif - -#ifdef CONFIG_USB_EPSON2888 -{ - USB_DEVICE (0x0525, 0x2888), // EPSON USB client - .driver_info = (unsigned long) &epson2888_info, -}, -#endif - -#ifdef CONFIG_USB_GENESYS -{ - USB_DEVICE (0x05e3, 0x0502), // GL620USB-A - .driver_info = (unsigned long) &genelink_info, -}, - /* NOT: USB_DEVICE (0x05e3, 0x0501), // GL620USB - * that's half duplex, not currently supported - */ -#endif - -#ifdef CONFIG_USB_NET1080 -{ - USB_DEVICE (0x0525, 0x1080), // NetChip ref design - .driver_info = (unsigned long) &net1080_info, -}, { - USB_DEVICE (0x06D0, 0x0622), // Laplink Gold - .driver_info = (unsigned long) &net1080_info, -}, -#endif - -#ifdef CONFIG_USB_PL2301 -{ - USB_DEVICE (0x067b, 0x0000), // PL-2301 - .driver_info = (unsigned long) &prolific_info, -}, { - USB_DEVICE (0x067b, 0x0001), // PL-2302 - .driver_info = (unsigned long) &prolific_info, -}, -#endif - -#ifdef CONFIG_USB_KC2190 -{ - USB_DEVICE (0x050f, 0x0190), // KC-190 - .driver_info = (unsigned long) &kc2190_info, -}, -#endif - -#ifdef CONFIG_USB_RNDIS -{ - /* RNDIS is MSFT's un-official variant of CDC ACM */ - USB_INTERFACE_INFO (USB_CLASS_COMM, 2 /* ACM */, 0x0ff), - .driver_info = (unsigned long) &rndis_info, -}, -#endif - -#ifdef CONFIG_USB_ARMLINUX -/* - * SA-1100 using standard ARM Linux kernels, or compatible. - * Often used when talking to Linux PDAs (iPaq, Yopy, etc). - * The sa-1100 "usb-eth" driver handles the basic framing. - * - * PXA25x or PXA210 ... these use a "usb-eth" driver much like - * the sa1100 one, but hardware uses different endpoint numbers. - * - * Or the Linux "Ethernet" gadget on hardware that can't talk - * CDC Ethernet (e.g., no altsettings), in either of two modes: - * - acting just like the old "usb-eth" firmware, though - * the implementation is different - * - supporting RNDIS as the first/default configuration for - * MS-Windows interop; Linux needs to use the other config - */ -{ - // 1183 = 0x049F, both used as hex values? - // Compaq "Itsy" vendor/product id - USB_DEVICE (0x049F, 0x505A), // usb-eth, or compatible - .driver_info = (unsigned long) &linuxdev_info, -}, { - USB_DEVICE (0x0E7E, 0x1001), // G.Mate "Yopy" - .driver_info = (unsigned long) &yopy_info, -}, { - USB_DEVICE (0x8086, 0x07d3), // "blob" bootloader - .driver_info = (unsigned long) &blob_info, -}, { - // Linux Ethernet/RNDIS gadget on pxa210/25x/26x - // e.g. Gumstix, current OpenZaurus, ... - USB_DEVICE_VER (0x0525, 0xa4a2, 0x0203, 0x0203), - .driver_info = (unsigned long) &linuxdev_info, -}, -#endif - -#if defined(CONFIG_USB_ZAURUS) || defined(CONFIG_USB_CDCETHER) -/* - * SA-1100 based Sharp Zaurus ("collie"), or compatible. - * Same idea as above, but different framing. - * - * PXA-2xx based models are also lying-about-cdc. - * Some models don't even tell the same lies ... - * - * NOTE: OpenZaurus versions with 2.6 kernels won't use these entries, - * unlike the older ones with 2.4 "embedix" kernels. - * - * NOTE: These entries do double-duty, serving as blacklist entries - * whenever Zaurus support isn't enabled, but CDC Ethernet is. - */ -#define ZAURUS_MASTER_INTERFACE \ - .bInterfaceClass = USB_CLASS_COMM, \ - .bInterfaceSubClass = USB_CDC_SUBCLASS_ETHERNET, \ - .bInterfaceProtocol = USB_CDC_PROTO_NONE -{ - .match_flags = USB_DEVICE_ID_MATCH_INT_INFO - | USB_DEVICE_ID_MATCH_DEVICE, - .idVendor = 0x04DD, - .idProduct = 0x8004, - ZAURUS_MASTER_INTERFACE, - .driver_info = ZAURUS_STRONGARM_INFO, -}, { - .match_flags = USB_DEVICE_ID_MATCH_INT_INFO - | USB_DEVICE_ID_MATCH_DEVICE, - .idVendor = 0x04DD, - .idProduct = 0x8005, /* A-300 */ - ZAURUS_MASTER_INTERFACE, - .driver_info = ZAURUS_PXA_INFO, -}, { - .match_flags = USB_DEVICE_ID_MATCH_INT_INFO - | USB_DEVICE_ID_MATCH_DEVICE, - .idVendor = 0x04DD, - .idProduct = 0x8006, /* B-500/SL-5600 */ - ZAURUS_MASTER_INTERFACE, - .driver_info = ZAURUS_PXA_INFO, -}, { - .match_flags = USB_DEVICE_ID_MATCH_INT_INFO - | USB_DEVICE_ID_MATCH_DEVICE, - .idVendor = 0x04DD, - .idProduct = 0x8007, /* C-700 */ - ZAURUS_MASTER_INTERFACE, - .driver_info = ZAURUS_PXA_INFO, -}, { - .match_flags = USB_DEVICE_ID_MATCH_INT_INFO - | USB_DEVICE_ID_MATCH_DEVICE, - .idVendor = 0x04DD, - .idProduct = 0x9031, /* C-750 C-760 */ - ZAURUS_MASTER_INTERFACE, - .driver_info = ZAURUS_PXA_INFO, -}, { - .match_flags = USB_DEVICE_ID_MATCH_INT_INFO - | USB_DEVICE_ID_MATCH_DEVICE, - .idVendor = 0x04DD, - .idProduct = 0x9032, /* SL-6000 */ - ZAURUS_MASTER_INTERFACE, - .driver_info = ZAURUS_PXA_INFO, -}, { - .match_flags = USB_DEVICE_ID_MATCH_INT_INFO - | USB_DEVICE_ID_MATCH_DEVICE, - .idVendor = 0x04DD, - /* reported with some C860 units */ - .idProduct = 0x9050, /* C-860 */ - ZAURUS_MASTER_INTERFACE, - .driver_info = ZAURUS_PXA_INFO, -}, - -#ifdef CONFIG_USB_ZAURUS - /* At least some (reports vary) PXA units have very different lies - * about their standards support: they claim to be cell phones with - * direct access to their radios. (They don't conform to CDC MDLM.) - */ -{ - USB_INTERFACE_INFO (USB_CLASS_COMM, USB_CDC_SUBCLASS_MDLM, - USB_CDC_PROTO_NONE), - .driver_info = (unsigned long) &bogus_mdlm_info, -}, -#endif - -/* Olympus has some models with a Zaurus-compatible option. - * R-1000 uses a FreeScale i.MXL cpu (ARMv4T) - */ -{ - .match_flags = USB_DEVICE_ID_MATCH_INT_INFO - | USB_DEVICE_ID_MATCH_DEVICE, - .idVendor = 0x07B4, - .idProduct = 0x0F02, /* R-1000 */ - ZAURUS_MASTER_INTERFACE, - .driver_info = OLYMPUS_MXL_INFO, -}, -#endif - -#ifdef CONFIG_USB_CDCETHER -{ - /* CDC Ether uses two interfaces, not necessarily consecutive. - * We match the main interface, ignoring the optional device - * class so we could handle devices that aren't exclusively - * CDC ether. - * - * NOTE: this match must come AFTER entries working around - * bugs/quirks in a given product (like Zaurus, above). - */ - USB_INTERFACE_INFO (USB_CLASS_COMM, USB_CDC_SUBCLASS_ETHERNET, - USB_CDC_PROTO_NONE), - .driver_info = (unsigned long) &cdc_info, -}, -#endif - - { }, // END -}; -MODULE_DEVICE_TABLE (usb, products); - -static struct usb_driver usbnet_driver = { - .owner = THIS_MODULE, - .name = driver_name, - .id_table = products, - .probe = usbnet_probe, - .disconnect = usbnet_disconnect, - .suspend = usbnet_suspend, - .resume = usbnet_resume, -}; - -/* Default ethtool_ops assigned. Devices can override in their bind() routine */ -static struct ethtool_ops usbnet_ethtool_ops = { - .get_drvinfo = usbnet_get_drvinfo, - .get_link = usbnet_get_link, - .get_msglevel = usbnet_get_msglevel, - .set_msglevel = usbnet_set_msglevel, -}; /*-------------------------------------------------------------------------*/ -static int __init usbnet_init (void) +static int __init usbnet_init(void) { - // compiler should optimize these out - BUG_ON (sizeof (((struct sk_buff *)0)->cb) + /* compiler should optimize this out */ + BUILD_BUG_ON (sizeof (((struct sk_buff *)0)->cb) < sizeof (struct skb_data)); -#ifdef CONFIG_USB_CDCETHER - BUG_ON ((sizeof (((struct usbnet *)0)->data) - < sizeof (struct cdc_state))); -#endif random_ether_addr(node_id); - - return usb_register(&usbnet_driver); + return 0; } -module_init (usbnet_init); +module_init(usbnet_init); -static void __exit usbnet_exit (void) +static void __exit usbnet_exit(void) { - usb_deregister (&usbnet_driver); } -module_exit (usbnet_exit); +module_exit(usbnet_exit); -MODULE_AUTHOR ("David Brownell "); -MODULE_DESCRIPTION ("USB Host-to-Host Link Drivers (numerous vendors)"); -MODULE_LICENSE ("GPL"); +MODULE_AUTHOR("David Brownell"); +MODULE_DESCRIPTION("USB network driver framework"); +MODULE_LICENSE("GPL");