X-Git-Url: http://ftp.safe.ca/?a=blobdiff_plain;f=drivers%2Fserial%2FKconfig;h=f7cd9504d81162c1e08c8f3b30ff18b3a40d3920;hb=7a63ce5a1f2fde5ae737f059e2714e441447120c;hp=ddfb1eab736371a6676ccdd637d197865b32ea2f;hpb=1f7d4f8395093021ed2262296179cfe71bd5e2ec;p=safe%2Fjmp%2Flinux-2.6

diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig
index ddfb1ea..f7cd950 100644
--- a/drivers/serial/Kconfig
+++ b/drivers/serial/Kconfig
@@ -380,6 +380,21 @@ config SERIAL_ATMEL_CONSOLE
 	  console is the device which receives all kernel messages and
 	  warnings and which allows logins in single user mode).
 
+config SERIAL_ATMEL_PDC
+	bool "Support DMA transfers on AT91 / AT32 serial port"
+	depends on SERIAL_ATMEL
+	default y
+	help
+	  Say Y here if you wish to use the PDC to do DMA transfers to
+	  and from the Atmel AT91 / AT32 serial port. In order to
+	  actually use DMA transfers, make sure that the use_dma_tx
+	  and use_dma_rx members in the atmel_uart_data struct is set
+	  appropriately for each port.
+
+	  Note that break and error handling currently doesn't work
+	  properly when DMA is enabled. Make sure that ports where
+	  this matters don't use DMA.
+
 config SERIAL_ATMEL_TTYAT
 	bool "Install as device ttyATn instead of ttySn"
 	depends on SERIAL_ATMEL=y
@@ -465,20 +480,24 @@ config SERIAL_DZ
 	bool "DECstation DZ serial driver"
 	depends on MACH_DECSTATION && 32BIT
 	select SERIAL_CORE
-	help
-	  DZ11-family serial controllers for VAXstations, including the
-	  DC7085, M7814, and M7819.
+	default y
+	---help---
+	  DZ11-family serial controllers for DECstations and VAXstations,
+	  including the DC7085, M7814, and M7819.
 
 config SERIAL_DZ_CONSOLE
 	bool "Support console on DECstation DZ serial driver"
 	depends on SERIAL_DZ=y
 	select SERIAL_CORE_CONSOLE
-	help
+	default y
+	---help---
 	  If you say Y here, it will be possible to use a serial port as the
 	  system console (the system console is the device which receives all
 	  kernel messages and warnings and which allows logins in single user
-	  mode).  Note that the firmware uses ttyS0 as the serial console on
-	  the Maxine and ttyS2 on the others.
+	  mode).
+
+	  Note that the firmware uses ttyS3 as the serial console on
+	  DECstations that use this driver.
 
 	  If unsure, say Y.
 
@@ -667,7 +686,7 @@ config UART0_RTS_PIN
 
 config SERIAL_BFIN_UART1
 	bool "Enable UART1"
-	depends on SERIAL_BFIN && (BF534 || BF536 || BF537 || BF54x)
+	depends on SERIAL_BFIN && (!BF531 && !BF532 && !BF533 && !BF561)
 	help
 	  Enable UART1
 
@@ -680,14 +699,14 @@ config BFIN_UART1_CTSRTS
 
 config UART1_CTS_PIN
 	int "UART1 CTS pin"
-	depends on BFIN_UART1_CTSRTS && (BF53x || BF561)
+	depends on BFIN_UART1_CTSRTS && !BF54x
 	default -1
 	help
 	  Refer to ./include/asm-blackfin/gpio.h to see the GPIO map.
 
 config UART1_RTS_PIN
 	int "UART1 RTS pin"
-	depends on BFIN_UART1_CTSRTS && (BF53x || BF561)
+	depends on BFIN_UART1_CTSRTS && !BF54x
 	default -1
 	help
 	  Refer to ./include/asm-blackfin/gpio.h to see the GPIO map.
@@ -877,15 +896,15 @@ config SERIAL_SUNHV
 	  systems.  Say Y if you want to be able to use this device.
 
 config SERIAL_IP22_ZILOG
-	tristate "IP22 Zilog8530 serial support"
-	depends on SGI_IP22
+	tristate "SGI Zilog8530 serial support"
+	depends on SGI_HAS_ZILOG
 	select SERIAL_CORE
 	help
-	  This driver supports the Zilog8530 serial ports found on SGI IP22
+	  This driver supports the Zilog8530 serial ports found on SGI
 	  systems.  Say Y or M if you want to be able to these serial ports.
 
 config SERIAL_IP22_ZILOG_CONSOLE
-	bool "Console on IP22 Zilog8530 serial port"
+	bool "Console on SGI Zilog8530 serial port"
 	depends on SERIAL_IP22_ZILOG=y
 	select SERIAL_CORE_CONSOLE
 
@@ -942,6 +961,9 @@ config SERIAL_CORE
 config SERIAL_CORE_CONSOLE
 	bool
 
+config CONSOLE_POLL
+	bool
+
 config SERIAL_68328
 	bool "68328 serial support"
 	depends on M68328 || M68EZ328 || M68VZ328
@@ -1318,4 +1340,19 @@ config SERIAL_QE
 	  This driver supports the QE serial ports on Freescale embedded
 	  PowerPC that contain a QUICC Engine.
 
+config SERIAL_SC26XX
+	tristate "SC2681/SC2692 serial port support"
+	depends on SNI_RM
+	select SERIAL_CORE
+	help
+	  This is a driver for the onboard serial ports of
+	  older RM400 machines.
+
+config SERIAL_SC26XX_CONSOLE
+	bool "Console on SC2681/SC2692 serial port"
+	depends on SERIAL_SC26XX
+	select SERIAL_CORE_CONSOLE
+	help
+	  Support for Console on SC2681/SC2692 serial ports.
+
 endmenu