X-Git-Url: http://ftp.safe.ca/?a=blobdiff_plain;f=drivers%2Fserial%2FKconfig;h=9ff47db0b2ced375c7463a504625cd49f63c925f;hb=2e2eb509aa7a333fe9931cf306fc7dbc3473f25b;hp=5cc6b91f8408d0c0fbc2e3bc00c7279643d71e84;hpb=138c5d258cf06c278f5d7fe0a806e50fe413a08f;p=safe%2Fjmp%2Flinux-2.6

diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig
index 5cc6b91..9ff47db 100644
--- a/drivers/serial/Kconfig
+++ b/drivers/serial/Kconfig
@@ -1,16 +1,14 @@
 #
 # Serial device configuration
 #
-# $Id: Kconfig,v 1.11 2004/03/11 18:08:04 lethal Exp $
-#
 
 menu "Serial drivers"
+	depends on HAS_IOMEM
 
 #
 # The new 8250/16550 serial drivers
 config SERIAL_8250
 	tristate "8250/16550 and compatible serial support"
-	depends on (BROKEN || !SPARC)
 	select SERIAL_CORE
 	---help---
 	  This selects whether you want to include the driver for the standard
@@ -61,8 +59,22 @@ config SERIAL_8250_CONSOLE
 	  kernel will automatically use the first serial line, /dev/ttyS0, as
 	  system console.
 
+	  You can set that using a kernel command line option such as
+	  "console=uart8250,io,0x3f8,9600n8"
+	  "console=uart8250,mmio,0xff5e0000,115200n8".
+	  and it will switch to normal serial console when the corresponding 
+	  port is ready.
+	  "earlycon=uart8250,io,0x3f8,9600n8"
+	  "earlycon=uart8250,mmio,0xff5e0000,115200n8".
+	  it will not only setup early console.
+
 	  If unsure, say N.
 
+config FIX_EARLYCON_MEM
+	bool
+	depends on X86
+	default y
+
 config SERIAL_8250_GSC
 	tristate
 	depends on SERIAL_8250 && GSC
@@ -247,11 +259,20 @@ config SERIAL_8250_ACORN
 	  cards.  If unsure, say N.
 
 config SERIAL_8250_AU1X00
-	bool "AU1X00 serial port support"
+	bool "Au1x00 serial port support"
 	depends on SERIAL_8250 != n && SOC_AU1X00
 	help
-	  If you have an Au1x00 board and want to use the serial port, say Y
-	  to this option.  The driver can handle 1 or 2 serial ports.
+	  If you have an Au1x00 SOC based board and want to use the serial port,
+	  say Y to this option. The driver can handle up to 4 serial ports,
+	  depending on the SOC. If unsure, say N.
+
+config SERIAL_8250_RM9K
+	bool "Support for MIPS RM9xxx integrated serial port"
+	depends on SERIAL_8250 != n && SERIAL_RM9000
+	select SERIAL_8250_SHARE_IRQ
+	help
+	  Selecting this option will add support for the integrated serial
+	  port hardware found on MIPS RM9122 and similar processors.
 	  If unsure, say N.
 
 comment "Non-8250 serial port support"
@@ -262,7 +283,8 @@ config SERIAL_AMBA_PL010
 	select SERIAL_CORE
 	help
 	  This selects the ARM(R) AMBA(R) PrimeCell PL010 UART.  If you have
-	  an Integrator/AP or Integrator/PP2 platform, say Y or M here.
+	  an Integrator/AP or Integrator/PP2 platform, or if you have a
+	  Cirrus Logic EP93xx CPU, say Y or M here.
 
 	  If unsure, say N.
 
@@ -309,6 +331,34 @@ config SERIAL_AMBA_PL011_CONSOLE
 	  your boot loader (lilo or loadlin) about how to pass options to the
 	  kernel at boot time.)
 
+config SERIAL_SB1250_DUART
+	tristate "BCM1xxx on-chip DUART serial support"
+	depends on SIBYTE_SB1xxx_SOC=y
+	select SERIAL_CORE
+	default y
+	---help---
+	  Support for the asynchronous serial interface (DUART) included in
+	  the BCM1250 and derived System-On-a-Chip (SOC) devices.  Note that
+	  the letter D in DUART stands for "dual", which is how the device
+	  is implemented.  Depending on the SOC configuration there may be
+	  one or more DUARTs available of which all are handled.
+
+	  If unsure, say Y.  To compile this driver as a module, choose M here:
+	  the module will be called sb1250-duart.
+
+config SERIAL_SB1250_DUART_CONSOLE
+	bool "Support for console on a BCM1xxx DUART serial port"
+	depends on SERIAL_SB1250_DUART=y
+	select SERIAL_CORE_CONSOLE
+	default y
+	---help---
+	  If you say Y here, it will be possible to use a serial port as the
+	  system console (the system console is the device which receives all
+	  kernel messages and warnings and which allows logins in single user
+	  mode).
+
+	  If unsure, say Y.
+
 config SERIAL_ATMEL
 	bool "AT91 / AT32 on-chip serial port support"
 	depends on (ARM && ARCH_AT91) || AVR32
@@ -327,6 +377,21 @@ config SERIAL_ATMEL_CONSOLE
 	  console is the device which receives all kernel messages and
 	  warnings and which allows logins in single user mode).
 
+config SERIAL_ATMEL_PDC
+	bool "Support DMA transfers on AT91 / AT32 serial port"
+	depends on SERIAL_ATMEL
+	default y
+	help
+	  Say Y here if you wish to use the PDC to do DMA transfers to
+	  and from the Atmel AT91 / AT32 serial port. In order to
+	  actually use DMA transfers, make sure that the use_dma_tx
+	  and use_dma_rx members in the atmel_uart_data struct is set
+	  appropriately for each port.
+
+	  Note that break and error handling currently doesn't work
+	  properly when DMA is enabled. Make sure that ports where
+	  this matters don't use DMA.
+
 config SERIAL_ATMEL_TTYAT
 	bool "Install as device ttyATn instead of ttySn"
 	depends on SERIAL_ATMEL=y
@@ -344,6 +409,23 @@ config SERIAL_ATMEL_TTYAT
 
 	  Say Y if you have an external 8250/16C550 UART.  If unsure, say N.
 
+config SERIAL_KS8695
+	bool "Micrel KS8695 (Centaur) serial port support"
+	depends on ARCH_KS8695
+	select SERIAL_CORE
+	help
+	  This selects the Micrel Centaur KS8695 UART.  Say Y here.
+
+config SERIAL_KS8695_CONSOLE
+	bool "Support for console on KS8695 (Centaur) serial port"
+	depends on SERIAL_KS8695=y
+	select SERIAL_CORE_CONSOLE
+	help
+	  Say Y here if you wish to use a KS8695 (Centaur) UART as the
+	  system console (the system console is the device which
+	  receives all kernel messages and warnings and which allows
+	  logins in single user mode).
+
 config SERIAL_CLPS711X
 	tristate "CLPS711X serial port support"
 	depends on ARM && ARCH_CLPS711X
@@ -363,9 +445,9 @@ config SERIAL_CLPS711X_CONSOLE
 	  your boot loader (lilo or loadlin) about how to pass options to the
 	  kernel at boot time.)
 
-config SERIAL_S3C2410
-	tristate "Samsung S3C2410/S3C2440/S3C2442/S3C2412 Serial port support"
-	depends on ARM && ARCH_S3C2410
+config SERIAL_SAMSUNG
+	tristate "Samsung SoC serial support"
+	depends on ARM && PLAT_S3C
 	select SERIAL_CORE
 	help
 	  Support for the on-chip UARTs on the Samsung S3C24XX series CPUs,
@@ -373,12 +455,28 @@ config SERIAL_S3C2410
 	  provide all of these ports, depending on how the serial port
 	  pins are configured.
 
-	  Currently this driver supports the UARTS on the S3C2410, S3C2440,
-	  S3C2442, S3C2412 and S3C2413 CPUs.
-
-config SERIAL_S3C2410_CONSOLE
-	bool "Support for console on S3C2410 serial port"
-	depends on SERIAL_S3C2410=y
+config SERIAL_SAMSUNG_UARTS
+	int
+	depends on ARM && PLAT_S3C
+	default 2 if ARCH_S3C2400
+	default 4 if ARCH_S5PC1XX || ARCH_S3C64XX || CPU_S3C2443
+	default 3
+	help
+	  Select the number of available UART ports for the Samsung S3C
+	  serial driver
+	
+config SERIAL_SAMSUNG_DEBUG
+	bool "Samsung SoC serial debug"
+	depends on SERIAL_SAMSUNG && DEBUG_LL
+	help
+	  Add support for debugging the serial driver. Since this is
+	  generally being used as a console, we use our own output
+	  routines that go via the low-level debug printascii()
+	  function.
+
+config SERIAL_SAMSUNG_CONSOLE
+	bool "Support for console on Samsung SoC serial port"
+	depends on SERIAL_SAMSUNG=y
 	select SERIAL_CORE_CONSOLE
 	help
 	  Allow selection of the S3C24XX on-board serial ports for use as
@@ -391,24 +489,116 @@ config SERIAL_S3C2410_CONSOLE
 	  your boot loader about how to pass options to the kernel at
 	  boot time.)
 
+config SERIAL_S3C2400
+	tristate "Samsung S3C2410 Serial port support"
+	depends on ARM && SERIAL_SAMSUNG && CPU_S3C2400
+	default y if CPU_S3C2400
+	help
+	  Serial port support for the Samsung S3C2400 SoC
+
+config SERIAL_S3C2410
+	tristate "Samsung S3C2410 Serial port support"
+	depends on SERIAL_SAMSUNG && CPU_S3C2410
+	default y if CPU_S3C2410
+	help
+	  Serial port support for the Samsung S3C2410 SoC
+
+config SERIAL_S3C2412
+	tristate "Samsung S3C2412/S3C2413 Serial port support"
+	depends on SERIAL_SAMSUNG && CPU_S3C2412
+	default y if CPU_S3C2412
+	help
+	  Serial port support for the Samsung S3C2412 and S3C2413 SoC
+
+config SERIAL_S3C2440
+	tristate "Samsung S3C2440/S3C2442 Serial port support"
+	depends on SERIAL_SAMSUNG && (CPU_S3C2440 || CPU_S3C2442)
+	default y if CPU_S3C2440
+	default y if CPU_S3C2442
+	help
+	  Serial port support for the Samsung S3C2440 and S3C2442 SoC
+
+config SERIAL_S3C24A0
+	tristate "Samsung S3C24A0 Serial port support"
+	depends on SERIAL_SAMSUNG && CPU_S3C24A0
+	default y if CPU_S3C24A0
+	help
+	  Serial port support for the Samsung S3C24A0 SoC
+
+config SERIAL_S3C6400
+	tristate "Samsung S3C6400/S3C6410 Serial port support"
+	depends on SERIAL_SAMSUNG && (CPU_S3C6400 || CPU_S3C6410)
+	default y
+	help
+	  Serial port support for the Samsung S3C6400 and S3C6410
+	  SoCs
+
+config SERIAL_S5PC100
+	tristate "Samsung S5PC100 Serial port support"
+	depends on SERIAL_SAMSUNG && CPU_S5PC100
+	default y
+	help
+	  Serial port support for the Samsung S5PC100 SoCs
+
+config SERIAL_MAX3100
+	tristate "MAX3100 support"
+	depends on SPI
+	select SERIAL_CORE
+	help
+	  MAX3100 chip support
+
 config SERIAL_DZ
 	bool "DECstation DZ serial driver"
 	depends on MACH_DECSTATION && 32BIT
 	select SERIAL_CORE
-	help
-	  DZ11-family serial controllers for VAXstations, including the
-	  DC7085, M7814, and M7819.
+	default y
+	---help---
+	  DZ11-family serial controllers for DECstations and VAXstations,
+	  including the DC7085, M7814, and M7819.
 
 config SERIAL_DZ_CONSOLE
 	bool "Support console on DECstation DZ serial driver"
 	depends on SERIAL_DZ=y
 	select SERIAL_CORE_CONSOLE
-	help
+	default y
+	---help---
+	  If you say Y here, it will be possible to use a serial port as the
+	  system console (the system console is the device which receives all
+	  kernel messages and warnings and which allows logins in single user
+	  mode).
+
+	  Note that the firmware uses ttyS3 as the serial console on
+	  DECstations that use this driver.
+
+	  If unsure, say Y.
+
+config SERIAL_ZS
+	tristate "DECstation Z85C30 serial support"
+	depends on MACH_DECSTATION
+	select SERIAL_CORE
+	default y
+	---help---
+	  Support for the Zilog 85C350 serial communications controller used
+	  for serial ports in newer DECstation systems.  These include the
+	  DECsystem 5900 and all models of the DECstation and DECsystem 5000
+	  systems except from model 200.
+
+	  If unsure, say Y.  To compile this driver as a module, choose M here:
+	  the module will be called zs.
+
+config SERIAL_ZS_CONSOLE
+	bool "Support for console on a DECstation Z85C30 serial port"
+	depends on SERIAL_ZS=y
+	select SERIAL_CORE_CONSOLE
+	default y
+	---help---
 	  If you say Y here, it will be possible to use a serial port as the
 	  system console (the system console is the device which receives all
 	  kernel messages and warnings and which allows logins in single user
-	  mode).  Note that the firmware uses ttyS0 as the serial console on
-	  the Maxine and ttyS2 on the others.
+	  mode).
+
+	  Note that the firmware uses ttyS1 as the serial console on the
+	  Maxine and ttyS3 on the others using this driver.
 
 	  If unsure, say Y.
 
@@ -452,7 +642,7 @@ config SERIAL_MPSC_CONSOLE
 
 config SERIAL_PXA
 	bool "PXA serial port support"
-	depends on ARM && ARCH_PXA
+	depends on ARCH_PXA || ARCH_MMP
 	select SERIAL_CORE
 	help
 	  If you have a machine based on an Intel XScale PXA2xx CPU you
@@ -498,10 +688,159 @@ config SERIAL_SA1100_CONSOLE
 	  your boot loader (lilo or loadlin) about how to pass options to the
 	  kernel at boot time.)
 
+config SERIAL_BFIN
+	tristate "Blackfin serial port support"
+	depends on BLACKFIN
+	select SERIAL_CORE
+	select SERIAL_BFIN_UART0 if (BF531 || BF532 || BF533 || BF561)
+	help
+	  Add support for the built-in UARTs on the Blackfin.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called bfin_5xx.
+
+config SERIAL_BFIN_CONSOLE
+	bool "Console on Blackfin serial port"
+	depends on SERIAL_BFIN=y
+	select SERIAL_CORE_CONSOLE
+
+choice
+	prompt "UART Mode"
+	depends on SERIAL_BFIN
+	default SERIAL_BFIN_DMA
+	help
+	  This driver supports the built-in serial ports of the Blackfin family
+	  of CPUs
+
+config SERIAL_BFIN_DMA
+	bool "DMA mode"
+	depends on !DMA_UNCACHED_NONE && KGDB_SERIAL_CONSOLE=n
+	help
+	  This driver works under DMA mode. If this option is selected, the
+	  blackfin simple dma driver is also enabled.
+
+config SERIAL_BFIN_PIO
+	bool "PIO mode"
+	help
+	  This driver works under PIO mode.
+
+endchoice
+
+config SERIAL_BFIN_UART0
+	bool "Enable UART0"
+	depends on SERIAL_BFIN
+	help
+	  Enable UART0
+
+config BFIN_UART0_CTSRTS
+	bool "Enable UART0 hardware flow control"
+	depends on SERIAL_BFIN_UART0
+	help
+	  Enable hardware flow control in the driver. Using GPIO emulate the CTS/RTS
+	  signal.
+
+config UART0_CTS_PIN
+	int "UART0 CTS pin"
+	depends on BFIN_UART0_CTSRTS && !BF548
+	default 23
+	help
+	  The default pin is GPIO_GP7.
+	  Refer to arch/blackfin/mach-*/include/mach/gpio.h to see the GPIO map.
+
+config UART0_RTS_PIN
+	int "UART0 RTS pin"
+	depends on BFIN_UART0_CTSRTS && !BF548
+	default 22
+	help
+	  The default pin is GPIO_GP6.
+	  Refer to arch/blackfin/mach-*/include/mach/gpio.h to see the GPIO map.
+
+config SERIAL_BFIN_UART1
+	bool "Enable UART1"
+	depends on SERIAL_BFIN && (!BF531 && !BF532 && !BF533 && !BF561)
+	help
+	  Enable UART1
+
+config BFIN_UART1_CTSRTS
+	bool "Enable UART1 hardware flow control"
+	depends on SERIAL_BFIN_UART1
+	help
+	  Enable hardware flow control in the driver. Using GPIO emulate the CTS/RTS
+	  signal.
+
+config UART1_CTS_PIN
+	int "UART1 CTS pin"
+	depends on BFIN_UART1_CTSRTS && !BF548
+	default -1
+	help
+	  Refer to arch/blackfin/mach-*/include/mach/gpio.h to see the GPIO map.
+
+config UART1_RTS_PIN
+	int "UART1 RTS pin"
+	depends on BFIN_UART1_CTSRTS && !BF548
+	default -1
+	help
+	  Refer to arch/blackfin/mach-*/include/mach/gpio.h to see the GPIO map.
+
+config SERIAL_BFIN_UART2
+	bool "Enable UART2"
+	depends on SERIAL_BFIN && (BF54x || BF538 || BF539)
+	help
+	  Enable UART2
+
+config BFIN_UART2_CTSRTS
+	bool "Enable UART2 hardware flow control"
+	depends on SERIAL_BFIN_UART2
+	help
+	  Enable hardware flow control in the driver. Using GPIO emulate the CTS/RTS
+	  signal.
+
+config UART2_CTS_PIN
+	int "UART2 CTS pin"
+	depends on BFIN_UART2_CTSRTS && !BF548
+	default -1
+	help
+	  Refer to arch/blackfin/mach-*/include/mach/gpio.h to see the GPIO map.
+
+config UART2_RTS_PIN
+	int "UART2 RTS pin"
+	depends on BFIN_UART2_CTSRTS && !BF548
+	default -1
+	help
+	  Refer to arch/blackfin/mach-*/include/mach/gpio.h to see the GPIO map.
+
+config SERIAL_BFIN_UART3
+	bool "Enable UART3"
+	depends on SERIAL_BFIN && (BF54x)
+	help
+	  Enable UART3
+
+config BFIN_UART3_CTSRTS
+	bool "Enable UART3 hardware flow control"
+	depends on SERIAL_BFIN_UART3
+	help
+	  Enable hardware flow control in the driver. Using GPIO emulate the CTS/RTS
+	  signal.
+
+config UART3_CTS_PIN
+	int "UART3 CTS pin"
+	depends on BFIN_UART3_CTSRTS && !BF548
+	default -1
+	help
+	  Refer to arch/blackfin/mach-*/include/mach/gpio.h to see the GPIO map.
+
+config UART3_RTS_PIN
+	int "UART3 RTS pin"
+	depends on BFIN_UART3_CTSRTS && !BF548
+	default -1
+	help
+	  Refer to arch/blackfin/mach-*/include/mach/gpio.h to see the GPIO map.
+
 config SERIAL_IMX
 	bool "IMX serial port support"
-	depends on ARM && ARCH_IMX
+	depends on ARM && (ARCH_IMX || ARCH_MXC)
 	select SERIAL_CORE
+	select RATIONAL
 	help
 	  If you have a machine based on a Motorola IMX CPU you
 	  can enable its onboard serial port by enabling this option.
@@ -523,13 +862,13 @@ config SERIAL_IMX_CONSOLE
 
 config SERIAL_UARTLITE
 	tristate "Xilinx uartlite serial port support"
-	depends on PPC32
+	depends on PPC32 || MICROBLAZE || MFD_TIMBERDALE
 	select SERIAL_CORE
 	help
 	  Say Y here if you want to use the Xilinx uartlite serial controller.
 
 	  To compile this driver as a module, choose M here: the
-	  module will be called uartlite.ko.
+	  module will be called uartlite.
 
 config SERIAL_UARTLITE_CONSOLE
 	bool "Support for console on Xilinx uartlite serial port"
@@ -598,10 +937,10 @@ config SERIAL_MUX
 	    4. Change the kernel command console parameter to: console=ttyB0
 
 config SERIAL_MUX_CONSOLE
-        bool "Support for console on serial MUX"
-        depends on SERIAL_MUX
+	bool "Support for console on serial MUX"
+	depends on SERIAL_MUX=y
 	select SERIAL_CORE_CONSOLE
-        default y
+	default y
 
 config PDC_CONSOLE
 	bool "PDC software console support"
@@ -643,37 +982,21 @@ config SERIAL_SUNHV
 	  systems.  Say Y if you want to be able to use this device.
 
 config SERIAL_IP22_ZILOG
-	tristate "IP22 Zilog8530 serial support"
-	depends on SGI_IP22
+	tristate "SGI Zilog8530 serial support"
+	depends on SGI_HAS_ZILOG
 	select SERIAL_CORE
 	help
-	  This driver supports the Zilog8530 serial ports found on SGI IP22
+	  This driver supports the Zilog8530 serial ports found on SGI
 	  systems.  Say Y or M if you want to be able to these serial ports.
 
 config SERIAL_IP22_ZILOG_CONSOLE
-	bool "Console on IP22 Zilog8530 serial port"
+	bool "Console on SGI Zilog8530 serial port"
 	depends on SERIAL_IP22_ZILOG=y
 	select SERIAL_CORE_CONSOLE
 
-config V850E_UART
-	bool "NEC V850E on-chip UART support"
-	depends on V850E_MA1 || V850E_ME2 || V850E_TEG || V850E2_ANNA || V850E_AS85EP1
-	select SERIAL_CORE
-	default y
-
-config V850E_UARTB
-        bool
-	depends on V850E_UART && V850E_ME2
-	default y
-
-config V850E_UART_CONSOLE
-	bool "Use NEC V850E on-chip UART for console"
-	depends on V850E_UART
-	select SERIAL_CORE_CONSOLE
-
 config SERIAL_SH_SCI
 	tristate "SuperH SCI(F) serial port support"
-	depends on SUPERH || H8300
+	depends on HAVE_CLK && (SUPERH || H8300)
 	select SERIAL_CORE
 
 config SERIAL_SH_SCI_NR_UARTS
@@ -686,12 +1009,31 @@ config SERIAL_SH_SCI_CONSOLE
 	depends on SERIAL_SH_SCI=y
 	select SERIAL_CORE_CONSOLE
 
+config SERIAL_PNX8XXX
+	bool "Enable PNX8XXX SoCs' UART Support"
+	depends on MIPS && (SOC_PNX8550 || SOC_PNX833X)
+	select SERIAL_CORE
+	help
+	  If you have a MIPS-based Philips SoC such as PNX8550 or PNX8330
+	  and you want to use serial ports, say Y.  Otherwise, say N.
+
+config SERIAL_PNX8XXX_CONSOLE
+	bool "Enable PNX8XX0 serial console"
+	depends on SERIAL_PNX8XXX
+	select SERIAL_CORE_CONSOLE
+	help
+	  If you have a MIPS-based Philips SoC such as PNX8550 or PNX8330
+	  and you want to use serial console, say Y. Otherwise, say N.
+
 config SERIAL_CORE
 	tristate
 
 config SERIAL_CORE_CONSOLE
 	bool
 
+config CONSOLE_POLL
+	bool
+
 config SERIAL_68328
 	bool "68328 serial support"
 	depends on M68328 || M68EZ328 || M68VZ328
@@ -703,12 +1045,28 @@ config SERIAL_68328_RTS_CTS
 	bool "Support RTS/CTS on 68328 serial port"
 	depends on SERIAL_68328
 
-config SERIAL_COLDFIRE
-	bool "ColdFire serial support"
+config SERIAL_MCF
+	bool "Coldfire serial support"
 	depends on COLDFIRE
+	select SERIAL_CORE
 	help
-	  This driver supports the built-in serial ports of the Motorola ColdFire
-	  family of CPUs.
+	  This serial driver supports the Freescale Coldfire serial ports.
+
+config SERIAL_MCF_BAUDRATE
+	int "Default baudrate for Coldfire serial ports"
+	depends on SERIAL_MCF
+	default 19200
+	help
+	  This setting lets you define what the default baudrate is for the
+	  ColdFire serial ports. The usual default varies from board to board,
+	  and this setting is a way of catering for that.
+
+config SERIAL_MCF_CONSOLE
+	bool "Coldfire serial console support"
+	depends on SERIAL_MCF
+	select SERIAL_CORE_CONSOLE
+	help
+	  Enable a ColdFire internal serial port to be the system console.
 
 config SERIAL_68360_SMC
 	bool "68360 SMC uart support"
@@ -736,6 +1094,31 @@ config SERIAL_PMACZILOG
 	  PowerMac machines.
 	  Say Y or M if you want to be able to these serial ports.
 
+config SERIAL_PMACZILOG_TTYS
+	bool "Use ttySn device nodes for Zilog z85c30"
+	depends on SERIAL_PMACZILOG
+	help
+	  The pmac_zilog driver for the z85C30 chip on many powermacs
+	  historically used the device numbers for /dev/ttySn.  The
+	  8250 serial port driver also uses these numbers, which means
+	  the two drivers being unable to coexist; you could not use
+	  both z85C30 and 8250 type ports at the same time.
+
+	  If this option is not selected, the pmac_zilog driver will
+	  use the device numbers allocated for /dev/ttyPZn.  This allows
+	  the pmac_zilog and 8250 drivers to co-exist, but may cause
+	  existing userspace setups to break.  Programs that need to
+	  access the built-in serial ports on powermacs will need to
+	  be reconfigured to use /dev/ttyPZn instead of /dev/ttySn.
+
+	  If you enable this option, any z85c30 ports in the system will
+	  be registered as ttyS0 onwards as in the past, and you will be
+	  unable to use the 8250 module for PCMCIA or other 16C550-style
+	  UARTs.
+
+	  Say N unless you need the z85c30 ports on your powermac
+	  to appear as /dev/ttySn.
+
 config SERIAL_PMACZILOG_CONSOLE
 	bool "Console on PowerMac z85c30 serial port"
 	depends on SERIAL_PMACZILOG=y
@@ -792,42 +1175,6 @@ config SERIAL_CPM_CONSOLE
 	  your boot loader (lilo or loadlin) about how to pass options to the
 	  kernel at boot time.)
 
-config SERIAL_CPM_SCC1
-	bool "Support for SCC1 serial port"
-	depends on SERIAL_CPM=y
-	help
-	  Select this option to use SCC1 as a serial port
-
-config SERIAL_CPM_SCC2
-	bool "Support for SCC2 serial port"
-	depends on SERIAL_CPM=y
-	help
-	  Select this option to use SCC2 as a serial port
-
-config SERIAL_CPM_SCC3
-	bool "Support for SCC3 serial port"
-	depends on SERIAL_CPM=y
-	help
-	  Select this option to use SCC3 as a serial port
-
-config SERIAL_CPM_SCC4
-	bool "Support for SCC4 serial port"
-	depends on SERIAL_CPM=y
-	help
-	  Select this option to use SCC4 as a serial port
-
-config SERIAL_CPM_SMC1
-	bool "Support for SMC1 serial port"
-	depends on SERIAL_CPM=y
-	help
-	  Select this option to use SMC1 as a serial port
-
-config SERIAL_CPM_SMC2
-	bool "Support for SMC2 serial port"
-	depends on SERIAL_CPM=y
-	help
-	  Select this option to use SMC2 as a serial port
-
 config SERIAL_SGI_L1_CONSOLE
 	bool "SGI Altix L1 serial console support"
 	depends on IA64_GENERIC || IA64_SGI_SN2
@@ -839,17 +1186,17 @@ config SERIAL_SGI_L1_CONSOLE
 		say Y.  Otherwise, say N.
 
 config SERIAL_MPC52xx
-	tristate "Freescale MPC52xx family PSC serial support"
-	depends on PPC_MPC52xx
+	tristate "Freescale MPC52xx/MPC512x family PSC serial support"
+	depends on PPC_MPC52xx || PPC_MPC512x
 	select SERIAL_CORE
 	help
-	  This drivers support the MPC52xx PSC serial ports. If you would
-	  like to use them, you must answer Y or M to this option. Not that
+	  This driver supports MPC52xx and MPC512x PSC serial ports. If you would
+	  like to use them, you must answer Y or M to this option. Note that
 	  for use as console, it must be included in kernel and not as a
 	  module.
 
 config SERIAL_MPC52xx_CONSOLE
-	bool "Console on a Freescale MPC52xx family PSC serial port"
+	bool "Console on a Freescale MPC52xx/MPC512x family PSC serial port"
 	depends on SERIAL_MPC52xx=y
 	select SERIAL_CORE_CONSOLE
 	help
@@ -857,7 +1204,7 @@ config SERIAL_MPC52xx_CONSOLE
 	  of the Freescale MPC52xx family as a console.
 
 config SERIAL_MPC52xx_CONSOLE_BAUD
-	int "Freescale MPC52xx family PSC serial port baud"
+	int "Freescale MPC52xx/MPC512x family PSC serial port baud"
 	depends on SERIAL_MPC52xx_CONSOLE=y
 	default "9600"
 	help
@@ -941,7 +1288,7 @@ config SERIAL_VR41XX
 
 config SERIAL_VR41XX_CONSOLE
 	bool "Enable NEC VR4100 series Serial Interface Unit console"
-	depends on SERIAL_VR41XX
+	depends on SERIAL_VR41XX=y
 	select SERIAL_CORE_CONSOLE
 	help
 	  If you have a NEC VR4100 series processor and you want to use
@@ -980,8 +1327,18 @@ config SERIAL_SGI_IOC3
 	  If you have an SGI Altix with an IOC3 serial card,
 	  say Y or M.  Otherwise, say N.
 
+config SERIAL_MSM
+	bool "MSM on-chip serial port support"
+	depends on ARM && ARCH_MSM
+	select SERIAL_CORE
+
+config SERIAL_MSM_CONSOLE
+	bool "MSM serial console support"
+	depends on SERIAL_MSM=y
+	select SERIAL_CORE_CONSOLE
+
 config SERIAL_NETX
-	bool "NetX serial port support"
+	tristate "NetX serial port support"
 	depends on ARM && ARCH_NETX
 	select SERIAL_CORE
 	help
@@ -993,10 +1350,144 @@ config SERIAL_NETX
 
 config SERIAL_NETX_CONSOLE
 	bool "Console on NetX serial port"
-	depends on SERIAL_NETX
+	depends on SERIAL_NETX=y
 	select SERIAL_CORE_CONSOLE
 	help
-	  If you have enabled the serial port on the Motorola IMX
-	  CPU you can make it the console by answering Y to this option.
+	  If you have enabled the serial port on the Hilscher NetX SoC
+	  you can make it the console by answering Y to this option.
+
+config SERIAL_OF_PLATFORM
+	tristate "Serial port on Open Firmware platform bus"
+	depends on PPC_OF || MICROBLAZE
+	depends on SERIAL_8250 || SERIAL_OF_PLATFORM_NWPSERIAL
+	help
+	  If you have a PowerPC based system that has serial ports
+	  on a platform specific bus, you should enable this option.
+	  Currently, only 8250 compatible ports are supported, but
+	  others can easily be added.
+
+config SERIAL_OF_PLATFORM_NWPSERIAL
+	tristate "NWP serial port driver"
+	depends on PPC_OF && PPC_DCR
+	select SERIAL_OF_PLATFORM
+	select SERIAL_CORE_CONSOLE
+	select SERIAL_CORE
+	help
+	  This driver supports the cell network processor nwp serial
+	  device.
+
+config SERIAL_OF_PLATFORM_NWPSERIAL_CONSOLE
+	bool "Console on NWP serial port"
+	depends on SERIAL_OF_PLATFORM_NWPSERIAL=y
+	select SERIAL_CORE_CONSOLE
+	help
+	  Support for Console on the NWP serial ports.
+
+config SERIAL_QE
+	tristate "Freescale QUICC Engine serial port support"
+	depends on QUICC_ENGINE
+	select SERIAL_CORE
+	select FW_LOADER
+	default n
+	help
+	  This driver supports the QE serial ports on Freescale embedded
+	  PowerPC that contain a QUICC Engine.
+
+config SERIAL_SC26XX
+	tristate "SC2681/SC2692 serial port support"
+	depends on SNI_RM
+	select SERIAL_CORE
+	help
+	  This is a driver for the onboard serial ports of
+	  older RM400 machines.
+
+config SERIAL_SC26XX_CONSOLE
+	bool "Console on SC2681/SC2692 serial port"
+	depends on SERIAL_SC26XX
+	select SERIAL_CORE_CONSOLE
+	help
+	  Support for Console on SC2681/SC2692 serial ports.
+
+config SERIAL_BFIN_SPORT
+	tristate "Blackfin SPORT emulate UART (EXPERIMENTAL)"
+	depends on BLACKFIN && EXPERIMENTAL
+	select SERIAL_CORE
+	help
+	  Enable SPORT emulate UART on Blackfin series.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called bfin_sport_uart.
+
+choice
+	prompt "Baud rate for Blackfin SPORT UART"
+	depends on SERIAL_BFIN_SPORT
+	default SERIAL_SPORT_BAUD_RATE_57600
+	help
+	  Choose a baud rate for the SPORT UART, other uart settings are
+	  8 bit, 1 stop bit, no parity, no flow control.
+
+config SERIAL_SPORT_BAUD_RATE_115200
+	bool "115200"
+
+config SERIAL_SPORT_BAUD_RATE_57600
+	bool "57600"
+
+config SERIAL_SPORT_BAUD_RATE_38400
+	bool "38400"
+
+config SERIAL_SPORT_BAUD_RATE_19200
+	bool "19200"
+
+config SERIAL_SPORT_BAUD_RATE_9600
+	bool "9600"
+endchoice
+
+config SPORT_BAUD_RATE
+	int
+	depends on SERIAL_BFIN_SPORT
+	default 115200 if (SERIAL_SPORT_BAUD_RATE_115200)
+	default 57600 if (SERIAL_SPORT_BAUD_RATE_57600)
+	default 38400 if (SERIAL_SPORT_BAUD_RATE_38400)
+	default 19200 if (SERIAL_SPORT_BAUD_RATE_19200)
+	default 9600 if (SERIAL_SPORT_BAUD_RATE_9600)
+
+config SERIAL_TIMBERDALE
+	tristate "Support for timberdale UART"
+	depends on MFD_TIMBERDALE
+	select SERIAL_CORE
+	---help---
+	Add support for UART controller on timberdale.
+
+config SERIAL_BCM63XX
+	tristate "bcm63xx serial port support"
+	select SERIAL_CORE
+	depends on BCM63XX
+	help
+	  If you have a bcm63xx CPU, you can enable its onboard
+	  serial port by enabling this options.
+
+          To compile this driver as a module, choose M here: the
+          module will be called bcm963xx_uart.
+
+config SERIAL_BCM63XX_CONSOLE
+	bool "Console on bcm63xx serial port"
+	depends on SERIAL_BCM63XX=y
+	select SERIAL_CORE_CONSOLE
+	help
+	  If you have enabled the serial port on the bcm63xx CPU
+	  you can make it the console by answering Y to this option.
+
+config SERIAL_GRLIB_GAISLER_APBUART
+	tristate "GRLIB APBUART serial support"
+	depends on OF
+	---help---
+	Add support for the GRLIB APBUART serial port.
+
+config SERIAL_GRLIB_GAISLER_APBUART_CONSOLE
+	bool "Console on GRLIB APBUART serial port"
+	depends on SERIAL_GRLIB_GAISLER_APBUART=y
+	select SERIAL_CORE_CONSOLE
+	help
+	Support for running a console on the GRLIB APBUART
 
 endmenu