X-Git-Url: http://ftp.safe.ca/?a=blobdiff_plain;f=drivers%2Fata%2Fsata_mv.c;h=71cc0d42f9e1c015ba90d27d4a457d5e247fddc5;hb=aab9796f5580a988c46c130a727cdc398a05317b;hp=b3f35a6af32beead6be82a1e61ce1a1b20bd05b9;hpb=f9f7fe014fc7197a5f36f9d9859cbb27c3bdd2ab;p=safe%2Fjmp%2Flinux-2.6 diff --git a/drivers/ata/sata_mv.c b/drivers/ata/sata_mv.c index b3f35a6..71cc0d4 100644 --- a/drivers/ata/sata_mv.c +++ b/drivers/ata/sata_mv.c @@ -1,10 +1,13 @@ /* * sata_mv.c - Marvell SATA support * - * Copyright 2008: Marvell Corporation, all rights reserved. + * Copyright 2008-2009: Marvell Corporation, all rights reserved. * Copyright 2005: EMC Corporation, all rights reserved. * Copyright 2005 Red Hat, Inc. All rights reserved. * + * Originally written by Brett Russ. + * Extensive overhaul and enhancement by Mark Lord . + * * Please ALWAYS copy linux-ide@vger.kernel.org on emails. * * This program is free software; you can redistribute it and/or modify @@ -23,46 +26,28 @@ */ /* - sata_mv TODO list: - - 1) Needs a full errata audit for all chipsets. I implemented most - of the errata workarounds found in the Marvell vendor driver, but - I distinctly remember a couple workarounds (one related to PCI-X) - are still needed. - - 2) Improve/fix IRQ and error handling sequences. - - 3) ATAPI support (Marvell claims the 60xx/70xx chips can do it). - - 4) Think about TCQ support here, and for libata in general - with controllers that suppport it via host-queuing hardware - (a software-only implementation could be a nightmare). - - 5) Investigate problems with PCI Message Signalled Interrupts (MSI). - - 6) Cache frequently-accessed registers in mv_port_priv to reduce overhead. - - 7) Fix/reenable hot plug/unplug (should happen as a side-effect of (2) above). - - 8) Develop a low-power-consumption strategy, and implement it. - - 9) [Experiment, low priority] See if ATAPI can be supported using - "unknown FIS" or "vendor-specific FIS" support, or something creative - like that. - - 10) [Experiment, low priority] Investigate interrupt coalescing. - Quite often, especially with PCI Message Signalled Interrupts (MSI), - the overhead reduced by interrupt mitigation is quite often not - worth the latency cost. - - 11) [Experiment, Marvell value added] Is it possible to use target - mode to cross-connect two Linux boxes with Marvell cards? If so, - creating LibATA target mode support would be very interesting. - - Target mode, for those without docs, is the ability to directly - connect two SATA controllers. + * sata_mv TODO list: + * + * --> Develop a low-power-consumption strategy, and implement it. + * + * --> Add sysfs attributes for per-chip / per-HC IRQ coalescing thresholds. + * + * --> [Experiment, Marvell value added] Is it possible to use target + * mode to cross-connect two Linux boxes with Marvell cards? If so, + * creating LibATA target mode support would be very interesting. + * + * Target mode, for those without docs, is the ability to directly + * connect two SATA ports. + */ -*/ +/* + * 80x1-B2 errata PCI#11: + * + * Users of the 6041/6081 Rev.B2 chips (current is C0) + * should be careful to insert those cards only onto PCI-X bus #0, + * and only in device slots 0..7, not higher. The chips may not + * work correctly otherwise (note: this is a pretty rare condition). + */ #include #include @@ -74,16 +59,39 @@ #include #include #include +#include #include #include #include +#include +#include #include #include #include #include #define DRV_NAME "sata_mv" -#define DRV_VERSION "1.20" +#define DRV_VERSION "1.28" + +/* + * module options + */ + +static int msi; +#ifdef CONFIG_PCI +module_param(msi, int, S_IRUGO); +MODULE_PARM_DESC(msi, "Enable use of PCI MSI (0=off, 1=on)"); +#endif + +static int irq_coalescing_io_count; +module_param(irq_coalescing_io_count, int, S_IRUGO); +MODULE_PARM_DESC(irq_coalescing_io_count, + "IRQ coalescing I/O count threshold (0..255)"); + +static int irq_coalescing_usecs; +module_param(irq_coalescing_usecs, int, S_IRUGO); +MODULE_PARM_DESC(irq_coalescing_usecs, + "IRQ coalescing time threshold in usecs"); enum { /* BAR's are enumerated in terms of pci_resource_start() terms */ @@ -94,18 +102,37 @@ enum { MV_MAJOR_REG_AREA_SZ = 0x10000, /* 64KB */ MV_MINOR_REG_AREA_SZ = 0x2000, /* 8KB */ + /* For use with both IRQ coalescing methods ("all ports" or "per-HC" */ + COAL_CLOCKS_PER_USEC = 150, /* for calculating COAL_TIMEs */ + MAX_COAL_TIME_THRESHOLD = ((1 << 24) - 1), /* internal clocks count */ + MAX_COAL_IO_COUNT = 255, /* completed I/O count */ + MV_PCI_REG_BASE = 0, - MV_IRQ_COAL_REG_BASE = 0x18000, /* 6xxx part only */ - MV_IRQ_COAL_CAUSE = (MV_IRQ_COAL_REG_BASE + 0x08), - MV_IRQ_COAL_CAUSE_LO = (MV_IRQ_COAL_REG_BASE + 0x88), - MV_IRQ_COAL_CAUSE_HI = (MV_IRQ_COAL_REG_BASE + 0x8c), - MV_IRQ_COAL_THRESHOLD = (MV_IRQ_COAL_REG_BASE + 0xcc), - MV_IRQ_COAL_TIME_THRESHOLD = (MV_IRQ_COAL_REG_BASE + 0xd0), - - MV_SATAHC0_REG_BASE = 0x20000, - MV_FLASH_CTL = 0x1046c, - MV_GPIO_PORT_CTL = 0x104f0, - MV_RESET_CFG = 0x180d8, + + /* + * Per-chip ("all ports") interrupt coalescing feature. + * This is only for GEN_II / GEN_IIE hardware. + * + * Coalescing defers the interrupt until either the IO_THRESHOLD + * (count of completed I/Os) is met, or the TIME_THRESHOLD is met. + */ + COAL_REG_BASE = 0x18000, + IRQ_COAL_CAUSE = (COAL_REG_BASE + 0x08), + ALL_PORTS_COAL_IRQ = (1 << 4), /* all ports irq event */ + + IRQ_COAL_IO_THRESHOLD = (COAL_REG_BASE + 0xcc), + IRQ_COAL_TIME_THRESHOLD = (COAL_REG_BASE + 0xd0), + + /* + * Registers for the (unused here) transaction coalescing feature: + */ + TRAN_COAL_CAUSE_LO = (COAL_REG_BASE + 0x88), + TRAN_COAL_CAUSE_HI = (COAL_REG_BASE + 0x8c), + + SATAHC0_REG_BASE = 0x20000, + FLASH_CTL = 0x1046c, + GPIO_PORT_CTL = 0x104f0, + RESET_CFG = 0x180d8, MV_PCI_REG_SZ = MV_MAJOR_REG_AREA_SZ, MV_SATAHC_REG_SZ = MV_MAJOR_REG_AREA_SZ, @@ -132,14 +159,16 @@ enum { /* Host Flags */ MV_FLAG_DUAL_HC = (1 << 30), /* two SATA Host Controllers */ - MV_FLAG_IRQ_COALESCE = (1 << 29), /* IRQ coalescing capability */ - /* SoC integrated controllers, no PCI interface */ - MV_FLAG_SOC = (1 << 28), MV_COMMON_FLAGS = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY | - ATA_FLAG_MMIO | ATA_FLAG_NO_ATAPI | - ATA_FLAG_PIO_POLLING, - MV_6XXX_FLAGS = MV_FLAG_IRQ_COALESCE, + ATA_FLAG_MMIO | ATA_FLAG_PIO_POLLING, + + MV_GEN_I_FLAGS = MV_COMMON_FLAGS | ATA_FLAG_NO_ATAPI, + + MV_GEN_II_FLAGS = MV_COMMON_FLAGS | ATA_FLAG_NCQ | + ATA_FLAG_PMP | ATA_FLAG_ACPI_SATA, + + MV_GEN_IIE_FLAGS = MV_GEN_II_FLAGS | ATA_FLAG_AN, CRQB_FLAG_READ = (1 << 0), CRQB_TAG_SHIFT = 1, @@ -158,14 +187,18 @@ enum { /* PCI interface registers */ - PCI_COMMAND_OFS = 0xc00, + MV_PCI_COMMAND = 0xc00, + MV_PCI_COMMAND_MWRCOM = (1 << 4), /* PCI Master Write Combining */ + MV_PCI_COMMAND_MRDTRIG = (1 << 7), /* PCI Master Read Trigger */ - PCI_MAIN_CMD_STS_OFS = 0xd30, + PCI_MAIN_CMD_STS = 0xd30, STOP_PCI_MASTER = (1 << 2), PCI_MASTER_EMPTY = (1 << 3), GLOB_SFT_RST = (1 << 4), MV_PCI_MODE = 0xd00, + MV_PCI_MODE_MASK = 0x30, + MV_PCI_EXP_ROM_BAR_CTL = 0xd2c, MV_PCI_DISC_TIMER = 0xd04, MV_PCI_MSI_TRIGGER = 0xc38, @@ -176,81 +209,105 @@ enum { MV_PCI_ERR_ATTRIBUTE = 0x1d48, MV_PCI_ERR_COMMAND = 0x1d50, - PCI_IRQ_CAUSE_OFS = 0x1d58, - PCI_IRQ_MASK_OFS = 0x1d5c, + PCI_IRQ_CAUSE = 0x1d58, + PCI_IRQ_MASK = 0x1d5c, PCI_UNMASK_ALL_IRQS = 0x7fffff, /* bits 22-0 */ - PCIE_IRQ_CAUSE_OFS = 0x1900, - PCIE_IRQ_MASK_OFS = 0x1910, + PCIE_IRQ_CAUSE = 0x1900, + PCIE_IRQ_MASK = 0x1910, PCIE_UNMASK_ALL_IRQS = 0x40a, /* assorted bits */ - HC_MAIN_IRQ_CAUSE_OFS = 0x1d60, - HC_MAIN_IRQ_MASK_OFS = 0x1d64, - HC_SOC_MAIN_IRQ_CAUSE_OFS = 0x20020, - HC_SOC_MAIN_IRQ_MASK_OFS = 0x20024, - ERR_IRQ = (1 << 0), /* shift by port # */ - DONE_IRQ = (1 << 1), /* shift by port # */ + /* Host Controller Main Interrupt Cause/Mask registers (1 per-chip) */ + PCI_HC_MAIN_IRQ_CAUSE = 0x1d60, + PCI_HC_MAIN_IRQ_MASK = 0x1d64, + SOC_HC_MAIN_IRQ_CAUSE = 0x20020, + SOC_HC_MAIN_IRQ_MASK = 0x20024, + ERR_IRQ = (1 << 0), /* shift by (2 * port #) */ + DONE_IRQ = (1 << 1), /* shift by (2 * port #) */ HC0_IRQ_PEND = 0x1ff, /* bits 0-8 = HC0's ports */ HC_SHIFT = 9, /* bits 9-17 = HC1's ports */ + DONE_IRQ_0_3 = 0x000000aa, /* DONE_IRQ ports 0,1,2,3 */ + DONE_IRQ_4_7 = (DONE_IRQ_0_3 << HC_SHIFT), /* 4,5,6,7 */ PCI_ERR = (1 << 18), - TRAN_LO_DONE = (1 << 19), /* 6xxx: IRQ coalescing */ - TRAN_HI_DONE = (1 << 20), /* 6xxx: IRQ coalescing */ - PORTS_0_3_COAL_DONE = (1 << 8), - PORTS_4_7_COAL_DONE = (1 << 17), - PORTS_0_7_COAL_DONE = (1 << 21), /* 6xxx: IRQ coalescing */ + TRAN_COAL_LO_DONE = (1 << 19), /* transaction coalescing */ + TRAN_COAL_HI_DONE = (1 << 20), /* transaction coalescing */ + PORTS_0_3_COAL_DONE = (1 << 8), /* HC0 IRQ coalescing */ + PORTS_4_7_COAL_DONE = (1 << 17), /* HC1 IRQ coalescing */ + ALL_PORTS_COAL_DONE = (1 << 21), /* GEN_II(E) IRQ coalescing */ GPIO_INT = (1 << 22), SELF_INT = (1 << 23), TWSI_INT = (1 << 24), HC_MAIN_RSVD = (0x7f << 25), /* bits 31-25 */ HC_MAIN_RSVD_5 = (0x1fff << 19), /* bits 31-19 */ HC_MAIN_RSVD_SOC = (0x3fffffb << 6), /* bits 31-9, 7-6 */ - HC_MAIN_MASKED_IRQS = (TRAN_LO_DONE | TRAN_HI_DONE | - PORTS_0_3_COAL_DONE | PORTS_4_7_COAL_DONE | - PORTS_0_7_COAL_DONE | GPIO_INT | TWSI_INT | - HC_MAIN_RSVD), - HC_MAIN_MASKED_IRQS_5 = (PORTS_0_3_COAL_DONE | PORTS_4_7_COAL_DONE | - HC_MAIN_RSVD_5), - HC_MAIN_MASKED_IRQS_SOC = (PORTS_0_3_COAL_DONE | HC_MAIN_RSVD_SOC), /* SATAHC registers */ - HC_CFG_OFS = 0, + HC_CFG = 0x00, - HC_IRQ_CAUSE_OFS = 0x14, + HC_IRQ_CAUSE = 0x14, DMA_IRQ = (1 << 0), /* shift by port # */ HC_COAL_IRQ = (1 << 4), /* IRQ coalescing */ DEV_IRQ = (1 << 8), /* shift by port # */ + /* + * Per-HC (Host-Controller) interrupt coalescing feature. + * This is present on all chip generations. + * + * Coalescing defers the interrupt until either the IO_THRESHOLD + * (count of completed I/Os) is met, or the TIME_THRESHOLD is met. + */ + HC_IRQ_COAL_IO_THRESHOLD = 0x000c, + HC_IRQ_COAL_TIME_THRESHOLD = 0x0010, + + SOC_LED_CTRL = 0x2c, + SOC_LED_CTRL_BLINK = (1 << 0), /* Active LED blink */ + SOC_LED_CTRL_ACT_PRESENCE = (1 << 2), /* Multiplex dev presence */ + /* with dev activity LED */ + /* Shadow block registers */ - SHD_BLK_OFS = 0x100, - SHD_CTL_AST_OFS = 0x20, /* ofs from SHD_BLK_OFS */ + SHD_BLK = 0x100, + SHD_CTL_AST = 0x20, /* ofs from SHD_BLK */ /* SATA registers */ - SATA_STATUS_OFS = 0x300, /* ctrl, err regs follow status */ - SATA_ACTIVE_OFS = 0x350, - SATA_FIS_IRQ_CAUSE_OFS = 0x364, + SATA_STATUS = 0x300, /* ctrl, err regs follow status */ + SATA_ACTIVE = 0x350, + FIS_IRQ_CAUSE = 0x364, + FIS_IRQ_CAUSE_AN = (1 << 9), /* async notification */ - LTMODE_OFS = 0x30c, + LTMODE = 0x30c, /* requires read-after-write */ LTMODE_BIT8 = (1 << 8), /* unknown, but necessary */ - PHY_MODE3 = 0x310, - PHY_MODE4 = 0x314, PHY_MODE2 = 0x330, - SATA_IFCTL_OFS = 0x344, - SATA_IFSTAT_OFS = 0x34c, - VENDOR_UNIQUE_FIS_OFS = 0x35c, + PHY_MODE3 = 0x310, + + PHY_MODE4 = 0x314, /* requires read-after-write */ + PHY_MODE4_CFG_MASK = 0x00000003, /* phy internal config field */ + PHY_MODE4_CFG_VALUE = 0x00000001, /* phy internal config field */ + PHY_MODE4_RSVD_ZEROS = 0x5de3fffa, /* Gen2e always write zeros */ + PHY_MODE4_RSVD_ONES = 0x00000005, /* Gen2e always write ones */ + + SATA_IFCTL = 0x344, + SATA_TESTCTL = 0x348, + SATA_IFSTAT = 0x34c, + VENDOR_UNIQUE_FIS = 0x35c, - FIS_CFG_OFS = 0x360, - FIS_CFG_SINGLE_SYNC = (1 << 16), /* SYNC on DMA activation */ + FISCFG = 0x360, + FISCFG_WAIT_DEV_ERR = (1 << 8), /* wait for host on DevErr */ + FISCFG_SINGLE_SYNC = (1 << 16), /* SYNC on DMA activation */ + + PHY_MODE9_GEN2 = 0x398, + PHY_MODE9_GEN1 = 0x39c, + PHYCFG_OFS = 0x3a0, /* only in 65n devices */ MV5_PHY_MODE = 0x74, - MV5_LT_MODE = 0x30, + MV5_LTMODE = 0x30, MV5_PHY_CTL = 0x0C, - SATA_INTERFACE_CFG = 0x050, + SATA_IFCFG = 0x050, MV_M2_PREAMP_MASK = 0x7e0, /* Port registers */ - EDMA_CFG_OFS = 0, + EDMA_CFG = 0, EDMA_CFG_Q_DEPTH = 0x1f, /* max device queue depth */ EDMA_CFG_NCQ = (1 << 5), /* for R/W FPDMA queued */ EDMA_CFG_NCQ_GO_ON_ERR = (1 << 14), /* continue on error */ @@ -259,8 +316,8 @@ enum { EDMA_CFG_EDMA_FBS = (1 << 16), /* EDMA FIS-Based Switching */ EDMA_CFG_FBS = (1 << 26), /* FIS-Based Switching */ - EDMA_ERR_IRQ_CAUSE_OFS = 0x8, - EDMA_ERR_IRQ_MASK_OFS = 0xc, + EDMA_ERR_IRQ_CAUSE = 0x8, + EDMA_ERR_IRQ_MASK = 0xc, EDMA_ERR_D_PAR = (1 << 0), /* UDMA data parity err */ EDMA_ERR_PRD_PAR = (1 << 1), /* UDMA PRD parity err */ EDMA_ERR_DEV = (1 << 2), /* device error */ @@ -300,9 +357,7 @@ enum { EDMA_ERR_IRQ_TRANSIENT = EDMA_ERR_LNK_CTRL_RX_0 | EDMA_ERR_LNK_CTRL_RX_1 | EDMA_ERR_LNK_CTRL_RX_3 | - EDMA_ERR_LNK_CTRL_TX | - /* temporary, until we fix hotplug: */ - (EDMA_ERR_DEV_DCON | EDMA_ERR_DEV_CON), + EDMA_ERR_LNK_CTRL_TX, EDMA_EH_FREEZE = EDMA_ERR_D_PAR | EDMA_ERR_PRD_PAR | @@ -331,26 +386,36 @@ enum { EDMA_ERR_INTRL_PAR | EDMA_ERR_IORDY, - EDMA_REQ_Q_BASE_HI_OFS = 0x10, - EDMA_REQ_Q_IN_PTR_OFS = 0x14, /* also contains BASE_LO */ + EDMA_REQ_Q_BASE_HI = 0x10, + EDMA_REQ_Q_IN_PTR = 0x14, /* also contains BASE_LO */ - EDMA_REQ_Q_OUT_PTR_OFS = 0x18, + EDMA_REQ_Q_OUT_PTR = 0x18, EDMA_REQ_Q_PTR_SHIFT = 5, - EDMA_RSP_Q_BASE_HI_OFS = 0x1c, - EDMA_RSP_Q_IN_PTR_OFS = 0x20, - EDMA_RSP_Q_OUT_PTR_OFS = 0x24, /* also contains BASE_LO */ + EDMA_RSP_Q_BASE_HI = 0x1c, + EDMA_RSP_Q_IN_PTR = 0x20, + EDMA_RSP_Q_OUT_PTR = 0x24, /* also contains BASE_LO */ EDMA_RSP_Q_PTR_SHIFT = 3, - EDMA_CMD_OFS = 0x28, /* EDMA command register */ + EDMA_CMD = 0x28, /* EDMA command register */ EDMA_EN = (1 << 0), /* enable EDMA */ EDMA_DS = (1 << 1), /* disable EDMA; self-negated */ - ATA_RST = (1 << 2), /* reset trans/link/phy */ + EDMA_RESET = (1 << 2), /* reset eng/trans/link/phy */ + + EDMA_STATUS = 0x30, /* EDMA engine status */ + EDMA_STATUS_CACHE_EMPTY = (1 << 6), /* GenIIe command cache empty */ + EDMA_STATUS_IDLE = (1 << 7), /* GenIIe EDMA enabled/idle */ EDMA_IORDY_TMOUT = 0x34, EDMA_ARB_CFG = 0x38, - GEN_II_NCQ_MAX_SECTORS = 256, /* max sects/io on Gen2 w/NCQ */ + EDMA_HALTCOND = 0x60, /* GenIIe halt conditions */ + EDMA_UNKNOWN_RSVD = 0x6C, /* GenIIe unknown/reserved */ + + BMDMA_CMD = 0x224, /* bmdma command register */ + BMDMA_STATUS = 0x228, /* bmdma status register */ + BMDMA_PRD_LOW = 0x22c, /* bmdma PRD addr 31:0 */ + BMDMA_PRD_HIGH = 0x230, /* bmdma PRD addr 63:32 */ /* Host private flags (hp_flags) */ MV_HP_FLAG_MSI = (1 << 0), @@ -358,21 +423,27 @@ enum { MV_HP_ERRATA_50XXB2 = (1 << 2), MV_HP_ERRATA_60X1B2 = (1 << 3), MV_HP_ERRATA_60X1C0 = (1 << 4), - MV_HP_ERRATA_XX42A0 = (1 << 5), MV_HP_GEN_I = (1 << 6), /* Generation I: 50xx */ MV_HP_GEN_II = (1 << 7), /* Generation II: 60xx */ MV_HP_GEN_IIE = (1 << 8), /* Generation IIE: 6042/7042 */ MV_HP_PCIE = (1 << 9), /* PCIe bus/regs: 7042 */ + MV_HP_CUT_THROUGH = (1 << 10), /* can use EDMA cut-through */ + MV_HP_FLAG_SOC = (1 << 11), /* SystemOnChip, no PCI */ + MV_HP_QUIRK_LED_BLINK_EN = (1 << 12), /* is led blinking enabled? */ /* Port private flags (pp_flags) */ MV_PP_FLAG_EDMA_EN = (1 << 0), /* is EDMA engine enabled? */ MV_PP_FLAG_NCQ_EN = (1 << 1), /* is EDMA set up for NCQ? */ + MV_PP_FLAG_FBS_EN = (1 << 2), /* is EDMA set up for FBS? */ + MV_PP_FLAG_DELAYED_EH = (1 << 3), /* delayed dev err handling */ + MV_PP_FLAG_FAKE_ATA_BUSY = (1 << 4), /* ignore initial ATA_DRDY */ }; #define IS_GEN_I(hpriv) ((hpriv)->hp_flags & MV_HP_GEN_I) #define IS_GEN_II(hpriv) ((hpriv)->hp_flags & MV_HP_GEN_II) #define IS_GEN_IIE(hpriv) ((hpriv)->hp_flags & MV_HP_GEN_IIE) -#define HAS_PCI(host) (!((host)->ports[0]->flags & MV_FLAG_SOC)) +#define IS_PCIE(hpriv) ((hpriv)->hp_flags & MV_HP_PCIE) +#define IS_SOC(hpriv) ((hpriv)->hp_flags & MV_HP_FLAG_SOC) #define WINDOW_CTRL(i) (0x20030 + ((i) << 4)) #define WINDOW_BASE(i) (0x20034 + ((i) << 4)) @@ -434,6 +505,18 @@ struct mv_sg { __le32 reserved; }; +/* + * We keep a local cache of a few frequently accessed port + * registers here, to avoid having to read them (very slow) + * when switching between EDMA and non-EDMA modes. + */ +struct mv_cached_regs { + u32 fiscfg; + u32 ltmode; + u32 haltcond; + u32 unknown_rsvd; +}; + struct mv_port_priv { struct mv_crqb *crqb; dma_addr_t crqb_dma; @@ -446,6 +529,8 @@ struct mv_port_priv { unsigned int resp_idx; u32 pp_flags; + struct mv_cached_regs cached; + unsigned int delayed_eh_pmp_map; }; struct mv_port_signal { @@ -455,15 +540,21 @@ struct mv_port_signal { struct mv_host_priv { u32 hp_flags; + unsigned int board_idx; + u32 main_irq_mask; struct mv_port_signal signal[8]; const struct mv_hw_ops *ops; int n_ports; void __iomem *base; - void __iomem *main_cause_reg_addr; - void __iomem *main_mask_reg_addr; - u32 irq_cause_ofs; - u32 irq_mask_ofs; + void __iomem *main_irq_cause_addr; + void __iomem *main_irq_mask_addr; + u32 irq_cause_offset; + u32 irq_mask_offset; u32 unmask_all_irqs; + +#if defined(CONFIG_HAVE_CLK) + struct clk *clk; +#endif /* * These consistent DMA memory pools give us guaranteed * alignment for hardware-accessed data structures, @@ -486,12 +577,13 @@ struct mv_hw_ops { void (*reset_bus)(struct ata_host *host, void __iomem *mmio); }; -static int mv_scr_read(struct ata_port *ap, unsigned int sc_reg_in, u32 *val); -static int mv_scr_write(struct ata_port *ap, unsigned int sc_reg_in, u32 val); -static int mv5_scr_read(struct ata_port *ap, unsigned int sc_reg_in, u32 *val); -static int mv5_scr_write(struct ata_port *ap, unsigned int sc_reg_in, u32 val); +static int mv_scr_read(struct ata_link *link, unsigned int sc_reg_in, u32 *val); +static int mv_scr_write(struct ata_link *link, unsigned int sc_reg_in, u32 val); +static int mv5_scr_read(struct ata_link *link, unsigned int sc_reg_in, u32 *val); +static int mv5_scr_write(struct ata_link *link, unsigned int sc_reg_in, u32 val); static int mv_port_start(struct ata_port *ap); static void mv_port_stop(struct ata_port *ap); +static int mv_qc_defer(struct ata_queued_cmd *qc); static void mv_qc_prep(struct ata_queued_cmd *qc); static void mv_qc_prep_iie(struct ata_queued_cmd *qc); static unsigned int mv_qc_issue(struct ata_queued_cmd *qc); @@ -528,18 +620,31 @@ static int mv_soc_reset_hc(struct mv_host_priv *hpriv, static void mv_soc_reset_flash(struct mv_host_priv *hpriv, void __iomem *mmio); static void mv_soc_reset_bus(struct ata_host *host, void __iomem *mmio); +static void mv_soc_65n_phy_errata(struct mv_host_priv *hpriv, + void __iomem *mmio, unsigned int port); static void mv_reset_pci_bus(struct ata_host *host, void __iomem *mmio); static void mv_reset_channel(struct mv_host_priv *hpriv, void __iomem *mmio, unsigned int port_no); static int mv_stop_edma(struct ata_port *ap); static int mv_stop_edma_engine(void __iomem *port_mmio); -static void mv_edma_cfg(struct ata_port *ap, int want_ncq); +static void mv_edma_cfg(struct ata_port *ap, int want_ncq, int want_edma); static void mv_pmp_select(struct ata_port *ap, int pmp); static int mv_pmp_hardreset(struct ata_link *link, unsigned int *class, unsigned long deadline); static int mv_softreset(struct ata_link *link, unsigned int *class, unsigned long deadline); +static void mv_pmp_error_handler(struct ata_port *ap); +static void mv_process_crpb_entries(struct ata_port *ap, + struct mv_port_priv *pp); + +static void mv_sff_irq_clear(struct ata_port *ap); +static int mv_check_atapi_dma(struct ata_queued_cmd *qc); +static void mv_bmdma_setup(struct ata_queued_cmd *qc); +static void mv_bmdma_start(struct ata_queued_cmd *qc); +static void mv_bmdma_stop(struct ata_queued_cmd *qc); +static u8 mv_bmdma_status(struct ata_port *ap); +static u8 mv_sff_check_status(struct ata_port *ap); /* .sg_tablesize is (MV_MAX_SG_CT / 2) in the structures below * because we have to allow room for worst case splitting of @@ -561,6 +666,9 @@ static struct scsi_host_template mv6_sht = { static struct ata_port_operations mv5_ops = { .inherits = &ata_sff_port_ops, + .lost_interrupt = ATA_OP_NULL, + + .qc_defer = mv_qc_defer, .qc_prep = mv_qc_prep, .qc_issue = mv_qc_issue, @@ -579,7 +687,6 @@ static struct ata_port_operations mv5_ops = { static struct ata_port_operations mv6_ops = { .inherits = &mv5_ops, - .qc_defer = sata_pmp_qc_defer_cmd_switch, .dev_config = mv6_dev_config, .scr_read = mv_scr_read, .scr_write = mv_scr_write, @@ -587,72 +694,69 @@ static struct ata_port_operations mv6_ops = { .pmp_hardreset = mv_pmp_hardreset, .pmp_softreset = mv_softreset, .softreset = mv_softreset, - .error_handler = sata_pmp_error_handler, + .error_handler = mv_pmp_error_handler, + + .sff_check_status = mv_sff_check_status, + .sff_irq_clear = mv_sff_irq_clear, + .check_atapi_dma = mv_check_atapi_dma, + .bmdma_setup = mv_bmdma_setup, + .bmdma_start = mv_bmdma_start, + .bmdma_stop = mv_bmdma_stop, + .bmdma_status = mv_bmdma_status, }; static struct ata_port_operations mv_iie_ops = { .inherits = &mv6_ops, - .qc_defer = ata_std_qc_defer, /* FIS-based switching */ .dev_config = ATA_OP_NULL, .qc_prep = mv_qc_prep_iie, }; static const struct ata_port_info mv_port_info[] = { { /* chip_504x */ - .flags = MV_COMMON_FLAGS, - .pio_mask = 0x1f, /* pio0-4 */ + .flags = MV_GEN_I_FLAGS, + .pio_mask = ATA_PIO4, .udma_mask = ATA_UDMA6, .port_ops = &mv5_ops, }, { /* chip_508x */ - .flags = MV_COMMON_FLAGS | MV_FLAG_DUAL_HC, - .pio_mask = 0x1f, /* pio0-4 */ + .flags = MV_GEN_I_FLAGS | MV_FLAG_DUAL_HC, + .pio_mask = ATA_PIO4, .udma_mask = ATA_UDMA6, .port_ops = &mv5_ops, }, { /* chip_5080 */ - .flags = MV_COMMON_FLAGS | MV_FLAG_DUAL_HC, - .pio_mask = 0x1f, /* pio0-4 */ + .flags = MV_GEN_I_FLAGS | MV_FLAG_DUAL_HC, + .pio_mask = ATA_PIO4, .udma_mask = ATA_UDMA6, .port_ops = &mv5_ops, }, { /* chip_604x */ - .flags = MV_COMMON_FLAGS | MV_6XXX_FLAGS | - ATA_FLAG_PMP | ATA_FLAG_ACPI_SATA | - ATA_FLAG_NCQ, - .pio_mask = 0x1f, /* pio0-4 */ + .flags = MV_GEN_II_FLAGS, + .pio_mask = ATA_PIO4, .udma_mask = ATA_UDMA6, .port_ops = &mv6_ops, }, { /* chip_608x */ - .flags = MV_COMMON_FLAGS | MV_6XXX_FLAGS | - ATA_FLAG_PMP | ATA_FLAG_ACPI_SATA | - ATA_FLAG_NCQ | MV_FLAG_DUAL_HC, - .pio_mask = 0x1f, /* pio0-4 */ + .flags = MV_GEN_II_FLAGS | MV_FLAG_DUAL_HC, + .pio_mask = ATA_PIO4, .udma_mask = ATA_UDMA6, .port_ops = &mv6_ops, }, { /* chip_6042 */ - .flags = MV_COMMON_FLAGS | MV_6XXX_FLAGS | - ATA_FLAG_PMP | ATA_FLAG_ACPI_SATA | - ATA_FLAG_NCQ, - .pio_mask = 0x1f, /* pio0-4 */ + .flags = MV_GEN_IIE_FLAGS, + .pio_mask = ATA_PIO4, .udma_mask = ATA_UDMA6, .port_ops = &mv_iie_ops, }, { /* chip_7042 */ - .flags = MV_COMMON_FLAGS | MV_6XXX_FLAGS | - ATA_FLAG_PMP | ATA_FLAG_ACPI_SATA | - ATA_FLAG_NCQ, - .pio_mask = 0x1f, /* pio0-4 */ + .flags = MV_GEN_IIE_FLAGS, + .pio_mask = ATA_PIO4, .udma_mask = ATA_UDMA6, .port_ops = &mv_iie_ops, }, { /* chip_soc */ - .flags = MV_COMMON_FLAGS | MV_6XXX_FLAGS | - ATA_FLAG_PMP | ATA_FLAG_ACPI_SATA | - ATA_FLAG_NCQ | MV_FLAG_SOC, - .pio_mask = 0x1f, /* pio0-4 */ + .flags = MV_GEN_IIE_FLAGS, + .pio_mask = ATA_PIO4, .udma_mask = ATA_UDMA6, .port_ops = &mv_iie_ops, }, @@ -663,9 +767,10 @@ static const struct pci_device_id mv_pci_tbl[] = { { PCI_VDEVICE(MARVELL, 0x5041), chip_504x }, { PCI_VDEVICE(MARVELL, 0x5080), chip_5080 }, { PCI_VDEVICE(MARVELL, 0x5081), chip_508x }, - /* RocketRAID 1740/174x have different identifiers */ - { PCI_VDEVICE(TTI, 0x1740), chip_508x }, - { PCI_VDEVICE(TTI, 0x1742), chip_508x }, + /* RocketRAID 1720/174x have different identifiers */ + { PCI_VDEVICE(TTI, 0x1720), chip_6042 }, + { PCI_VDEVICE(TTI, 0x1740), chip_6042 }, + { PCI_VDEVICE(TTI, 0x1742), chip_6042 }, { PCI_VDEVICE(MARVELL, 0x6040), chip_604x }, { PCI_VDEVICE(MARVELL, 0x6041), chip_604x }, @@ -715,6 +820,14 @@ static const struct mv_hw_ops mv_soc_ops = { .reset_bus = mv_soc_reset_bus, }; +static const struct mv_hw_ops mv_soc_65n_ops = { + .phy_errata = mv_soc_65n_phy_errata, + .enable_leds = mv_soc_enable_leds, + .reset_hc = mv_soc_reset_hc, + .reset_flash = mv_soc_reset_flash, + .reset_bus = mv_soc_reset_bus, +}; + /* * Functions */ @@ -735,9 +848,27 @@ static inline unsigned int mv_hardport_from_port(unsigned int port) return port & MV_PORT_MASK; } +/* + * Consolidate some rather tricky bit shift calculations. + * This is hot-path stuff, so not a function. + * Simple code, with two return values, so macro rather than inline. + * + * port is the sole input, in range 0..7. + * shift is one output, for use with main_irq_cause / main_irq_mask registers. + * hardport is the other output, in range 0..3. + * + * Note that port and hardport may be the same variable in some cases. + */ +#define MV_PORT_TO_SHIFT_AND_HARDPORT(port, shift, hardport) \ +{ \ + shift = mv_hc_from_port(port) * HC_SHIFT; \ + hardport = mv_hardport_from_port(port); \ + shift += hardport * 2; \ +} + static inline void __iomem *mv_hc_base(void __iomem *base, unsigned int hc) { - return (base + MV_SATAHC0_REG_BASE + (hc * MV_SATAHC_REG_SZ)); + return (base + SATAHC0_REG_BASE + (hc * MV_SATAHC_REG_SZ)); } static inline void __iomem *mv_hc_base_from_port(void __iomem *base, @@ -777,6 +908,62 @@ static inline int mv_get_hc_count(unsigned long port_flags) return ((port_flags & MV_FLAG_DUAL_HC) ? 2 : 1); } +/** + * mv_save_cached_regs - (re-)initialize cached port registers + * @ap: the port whose registers we are caching + * + * Initialize the local cache of port registers, + * so that reading them over and over again can + * be avoided on the hotter paths of this driver. + * This saves a few microseconds each time we switch + * to/from EDMA mode to perform (eg.) a drive cache flush. + */ +static void mv_save_cached_regs(struct ata_port *ap) +{ + void __iomem *port_mmio = mv_ap_base(ap); + struct mv_port_priv *pp = ap->private_data; + + pp->cached.fiscfg = readl(port_mmio + FISCFG); + pp->cached.ltmode = readl(port_mmio + LTMODE); + pp->cached.haltcond = readl(port_mmio + EDMA_HALTCOND); + pp->cached.unknown_rsvd = readl(port_mmio + EDMA_UNKNOWN_RSVD); +} + +/** + * mv_write_cached_reg - write to a cached port register + * @addr: hardware address of the register + * @old: pointer to cached value of the register + * @new: new value for the register + * + * Write a new value to a cached register, + * but only if the value is different from before. + */ +static inline void mv_write_cached_reg(void __iomem *addr, u32 *old, u32 new) +{ + if (new != *old) { + unsigned long laddr; + *old = new; + /* + * Workaround for 88SX60x1-B2 FEr SATA#13: + * Read-after-write is needed to prevent generating 64-bit + * write cycles on the PCI bus for SATA interface registers + * at offsets ending in 0x4 or 0xc. + * + * Looks like a lot of fuss, but it avoids an unnecessary + * +1 usec read-after-write delay for unaffected registers. + */ + laddr = (long)addr & 0xffff; + if (laddr >= 0x300 && laddr <= 0x33c) { + laddr &= 0x000f; + if (laddr == 0x4 || laddr == 0xc) { + writelfl(new, addr); /* read after write */ + return; + } + } + writel(new, addr); /* unaffected by the errata */ + } +} + static void mv_set_edma_ptrs(void __iomem *port_mmio, struct mv_host_priv *hpriv, struct mv_port_priv *pp) @@ -786,39 +973,160 @@ static void mv_set_edma_ptrs(void __iomem *port_mmio, /* * initialize request queue */ - index = (pp->req_idx & MV_MAX_Q_DEPTH_MASK) << EDMA_REQ_Q_PTR_SHIFT; + pp->req_idx &= MV_MAX_Q_DEPTH_MASK; /* paranoia */ + index = pp->req_idx << EDMA_REQ_Q_PTR_SHIFT; WARN_ON(pp->crqb_dma & 0x3ff); - writel((pp->crqb_dma >> 16) >> 16, port_mmio + EDMA_REQ_Q_BASE_HI_OFS); + writel((pp->crqb_dma >> 16) >> 16, port_mmio + EDMA_REQ_Q_BASE_HI); writelfl((pp->crqb_dma & EDMA_REQ_Q_BASE_LO_MASK) | index, - port_mmio + EDMA_REQ_Q_IN_PTR_OFS); - - if (hpriv->hp_flags & MV_HP_ERRATA_XX42A0) - writelfl((pp->crqb_dma & 0xffffffff) | index, - port_mmio + EDMA_REQ_Q_OUT_PTR_OFS); - else - writelfl(index, port_mmio + EDMA_REQ_Q_OUT_PTR_OFS); + port_mmio + EDMA_REQ_Q_IN_PTR); + writelfl(index, port_mmio + EDMA_REQ_Q_OUT_PTR); /* * initialize response queue */ - index = (pp->resp_idx & MV_MAX_Q_DEPTH_MASK) << EDMA_RSP_Q_PTR_SHIFT; + pp->resp_idx &= MV_MAX_Q_DEPTH_MASK; /* paranoia */ + index = pp->resp_idx << EDMA_RSP_Q_PTR_SHIFT; WARN_ON(pp->crpb_dma & 0xff); - writel((pp->crpb_dma >> 16) >> 16, port_mmio + EDMA_RSP_Q_BASE_HI_OFS); + writel((pp->crpb_dma >> 16) >> 16, port_mmio + EDMA_RSP_Q_BASE_HI); + writelfl(index, port_mmio + EDMA_RSP_Q_IN_PTR); + writelfl((pp->crpb_dma & EDMA_RSP_Q_BASE_LO_MASK) | index, + port_mmio + EDMA_RSP_Q_OUT_PTR); +} - if (hpriv->hp_flags & MV_HP_ERRATA_XX42A0) - writelfl((pp->crpb_dma & 0xffffffff) | index, - port_mmio + EDMA_RSP_Q_IN_PTR_OFS); - else - writelfl(index, port_mmio + EDMA_RSP_Q_IN_PTR_OFS); +static void mv_write_main_irq_mask(u32 mask, struct mv_host_priv *hpriv) +{ + /* + * When writing to the main_irq_mask in hardware, + * we must ensure exclusivity between the interrupt coalescing bits + * and the corresponding individual port DONE_IRQ bits. + * + * Note that this register is really an "IRQ enable" register, + * not an "IRQ mask" register as Marvell's naming might suggest. + */ + if (mask & (ALL_PORTS_COAL_DONE | PORTS_0_3_COAL_DONE)) + mask &= ~DONE_IRQ_0_3; + if (mask & (ALL_PORTS_COAL_DONE | PORTS_4_7_COAL_DONE)) + mask &= ~DONE_IRQ_4_7; + writelfl(mask, hpriv->main_irq_mask_addr); +} - writelfl((pp->crpb_dma & EDMA_RSP_Q_BASE_LO_MASK) | index, - port_mmio + EDMA_RSP_Q_OUT_PTR_OFS); +static void mv_set_main_irq_mask(struct ata_host *host, + u32 disable_bits, u32 enable_bits) +{ + struct mv_host_priv *hpriv = host->private_data; + u32 old_mask, new_mask; + + old_mask = hpriv->main_irq_mask; + new_mask = (old_mask & ~disable_bits) | enable_bits; + if (new_mask != old_mask) { + hpriv->main_irq_mask = new_mask; + mv_write_main_irq_mask(new_mask, hpriv); + } +} + +static void mv_enable_port_irqs(struct ata_port *ap, + unsigned int port_bits) +{ + unsigned int shift, hardport, port = ap->port_no; + u32 disable_bits, enable_bits; + + MV_PORT_TO_SHIFT_AND_HARDPORT(port, shift, hardport); + + disable_bits = (DONE_IRQ | ERR_IRQ) << shift; + enable_bits = port_bits << shift; + mv_set_main_irq_mask(ap->host, disable_bits, enable_bits); +} + +static void mv_clear_and_enable_port_irqs(struct ata_port *ap, + void __iomem *port_mmio, + unsigned int port_irqs) +{ + struct mv_host_priv *hpriv = ap->host->private_data; + int hardport = mv_hardport_from_port(ap->port_no); + void __iomem *hc_mmio = mv_hc_base_from_port( + mv_host_base(ap->host), ap->port_no); + u32 hc_irq_cause; + + /* clear EDMA event indicators, if any */ + writelfl(0, port_mmio + EDMA_ERR_IRQ_CAUSE); + + /* clear pending irq events */ + hc_irq_cause = ~((DEV_IRQ | DMA_IRQ) << hardport); + writelfl(hc_irq_cause, hc_mmio + HC_IRQ_CAUSE); + + /* clear FIS IRQ Cause */ + if (IS_GEN_IIE(hpriv)) + writelfl(0, port_mmio + FIS_IRQ_CAUSE); + + mv_enable_port_irqs(ap, port_irqs); +} + +static void mv_set_irq_coalescing(struct ata_host *host, + unsigned int count, unsigned int usecs) +{ + struct mv_host_priv *hpriv = host->private_data; + void __iomem *mmio = hpriv->base, *hc_mmio; + u32 coal_enable = 0; + unsigned long flags; + unsigned int clks, is_dual_hc = hpriv->n_ports > MV_PORTS_PER_HC; + const u32 coal_disable = PORTS_0_3_COAL_DONE | PORTS_4_7_COAL_DONE | + ALL_PORTS_COAL_DONE; + + /* Disable IRQ coalescing if either threshold is zero */ + if (!usecs || !count) { + clks = count = 0; + } else { + /* Respect maximum limits of the hardware */ + clks = usecs * COAL_CLOCKS_PER_USEC; + if (clks > MAX_COAL_TIME_THRESHOLD) + clks = MAX_COAL_TIME_THRESHOLD; + if (count > MAX_COAL_IO_COUNT) + count = MAX_COAL_IO_COUNT; + } + + spin_lock_irqsave(&host->lock, flags); + mv_set_main_irq_mask(host, coal_disable, 0); + + if (is_dual_hc && !IS_GEN_I(hpriv)) { + /* + * GEN_II/GEN_IIE with dual host controllers: + * one set of global thresholds for the entire chip. + */ + writel(clks, mmio + IRQ_COAL_TIME_THRESHOLD); + writel(count, mmio + IRQ_COAL_IO_THRESHOLD); + /* clear leftover coal IRQ bit */ + writel(~ALL_PORTS_COAL_IRQ, mmio + IRQ_COAL_CAUSE); + if (count) + coal_enable = ALL_PORTS_COAL_DONE; + clks = count = 0; /* force clearing of regular regs below */ + } + + /* + * All chips: independent thresholds for each HC on the chip. + */ + hc_mmio = mv_hc_base_from_port(mmio, 0); + writel(clks, hc_mmio + HC_IRQ_COAL_TIME_THRESHOLD); + writel(count, hc_mmio + HC_IRQ_COAL_IO_THRESHOLD); + writel(~HC_COAL_IRQ, hc_mmio + HC_IRQ_CAUSE); + if (count) + coal_enable |= PORTS_0_3_COAL_DONE; + if (is_dual_hc) { + hc_mmio = mv_hc_base_from_port(mmio, MV_PORTS_PER_HC); + writel(clks, hc_mmio + HC_IRQ_COAL_TIME_THRESHOLD); + writel(count, hc_mmio + HC_IRQ_COAL_IO_THRESHOLD); + writel(~HC_COAL_IRQ, hc_mmio + HC_IRQ_CAUSE); + if (count) + coal_enable |= PORTS_4_7_COAL_DONE; + } + + mv_set_main_irq_mask(host, 0, coal_enable); + spin_unlock_irqrestore(&host->lock, flags); } /** - * mv_start_dma - Enable eDMA engine + * mv_start_edma - Enable eDMA engine * @base: port base address * @pp: port private data * @@ -828,7 +1136,7 @@ static void mv_set_edma_ptrs(void __iomem *port_mmio, * LOCKING: * Inherited from caller. */ -static void mv_start_dma(struct ata_port *ap, void __iomem *port_mmio, +static void mv_start_edma(struct ata_port *ap, void __iomem *port_mmio, struct mv_port_priv *pp, u8 protocol) { int want_ncq = (protocol == ATA_PROT_NCQ); @@ -840,34 +1148,40 @@ static void mv_start_dma(struct ata_port *ap, void __iomem *port_mmio, } if (!(pp->pp_flags & MV_PP_FLAG_EDMA_EN)) { struct mv_host_priv *hpriv = ap->host->private_data; - int hardport = mv_hardport_from_port(ap->port_no); - void __iomem *hc_mmio = mv_hc_base_from_port( - mv_host_base(ap->host), hardport); - u32 hc_irq_cause, ipending; - - /* clear EDMA event indicators, if any */ - writelfl(0, port_mmio + EDMA_ERR_IRQ_CAUSE_OFS); - - /* clear EDMA interrupt indicator, if any */ - hc_irq_cause = readl(hc_mmio + HC_IRQ_CAUSE_OFS); - ipending = (DEV_IRQ | DMA_IRQ) << hardport; - if (hc_irq_cause & ipending) { - writelfl(hc_irq_cause & ~ipending, - hc_mmio + HC_IRQ_CAUSE_OFS); - } - - mv_edma_cfg(ap, want_ncq); - /* clear FIS IRQ Cause */ - writelfl(0, port_mmio + SATA_FIS_IRQ_CAUSE_OFS); + mv_edma_cfg(ap, want_ncq, 1); mv_set_edma_ptrs(port_mmio, hpriv, pp); + mv_clear_and_enable_port_irqs(ap, port_mmio, DONE_IRQ|ERR_IRQ); - writelfl(EDMA_EN, port_mmio + EDMA_CMD_OFS); + writelfl(EDMA_EN, port_mmio + EDMA_CMD); pp->pp_flags |= MV_PP_FLAG_EDMA_EN; } } +static void mv_wait_for_edma_empty_idle(struct ata_port *ap) +{ + void __iomem *port_mmio = mv_ap_base(ap); + const u32 empty_idle = (EDMA_STATUS_CACHE_EMPTY | EDMA_STATUS_IDLE); + const int per_loop = 5, timeout = (15 * 1000 / per_loop); + int i; + + /* + * Wait for the EDMA engine to finish transactions in progress. + * No idea what a good "timeout" value might be, but measurements + * indicate that it often requires hundreds of microseconds + * with two drives in-use. So we use the 15msec value above + * as a rough guess at what even more drives might require. + */ + for (i = 0; i < timeout; ++i) { + u32 edma_stat = readl(port_mmio + EDMA_STATUS); + if ((edma_stat & empty_idle) == empty_idle) + break; + udelay(per_loop); + } + /* ata_port_printk(ap, KERN_INFO, "%s: %u+ usecs\n", __func__, i); */ +} + /** * mv_stop_edma_engine - Disable eDMA engine * @port_mmio: io base address @@ -880,11 +1194,11 @@ static int mv_stop_edma_engine(void __iomem *port_mmio) int i; /* Disable eDMA. The disable bit auto clears. */ - writelfl(EDMA_DS, port_mmio + EDMA_CMD_OFS); + writelfl(EDMA_DS, port_mmio + EDMA_CMD); /* Wait for the chip to confirm eDMA is off. */ for (i = 10000; i > 0; i--) { - u32 reg = readl(port_mmio + EDMA_CMD_OFS); + u32 reg = readl(port_mmio + EDMA_CMD); if (!(reg & EDMA_EN)) return 0; udelay(10); @@ -896,15 +1210,18 @@ static int mv_stop_edma(struct ata_port *ap) { void __iomem *port_mmio = mv_ap_base(ap); struct mv_port_priv *pp = ap->private_data; + int err = 0; if (!(pp->pp_flags & MV_PP_FLAG_EDMA_EN)) return 0; pp->pp_flags &= ~MV_PP_FLAG_EDMA_EN; + mv_wait_for_edma_empty_idle(ap); if (mv_stop_edma_engine(port_mmio)) { ata_port_printk(ap, KERN_ERR, "Unable to stop eDMA\n"); - return -EIO; + err = -EIO; } - return 0; + mv_edma_cfg(ap, 0, 0); + return err; } #ifdef ATA_DEBUG @@ -991,10 +1308,10 @@ static unsigned int mv_scr_offset(unsigned int sc_reg_in) case SCR_STATUS: case SCR_CONTROL: case SCR_ERROR: - ofs = SATA_STATUS_OFS + (sc_reg_in * sizeof(u32)); + ofs = SATA_STATUS + (sc_reg_in * sizeof(u32)); break; case SCR_ACTIVE: - ofs = SATA_ACTIVE_OFS; /* active is not with the others */ + ofs = SATA_ACTIVE; /* active is not with the others */ break; default: ofs = 0xffffffffU; @@ -1003,23 +1320,41 @@ static unsigned int mv_scr_offset(unsigned int sc_reg_in) return ofs; } -static int mv_scr_read(struct ata_port *ap, unsigned int sc_reg_in, u32 *val) +static int mv_scr_read(struct ata_link *link, unsigned int sc_reg_in, u32 *val) { unsigned int ofs = mv_scr_offset(sc_reg_in); if (ofs != 0xffffffffU) { - *val = readl(mv_ap_base(ap) + ofs); + *val = readl(mv_ap_base(link->ap) + ofs); return 0; } else return -EINVAL; } -static int mv_scr_write(struct ata_port *ap, unsigned int sc_reg_in, u32 val) +static int mv_scr_write(struct ata_link *link, unsigned int sc_reg_in, u32 val) { unsigned int ofs = mv_scr_offset(sc_reg_in); if (ofs != 0xffffffffU) { - writelfl(val, mv_ap_base(ap) + ofs); + void __iomem *addr = mv_ap_base(link->ap) + ofs; + if (sc_reg_in == SCR_CONTROL) { + /* + * Workaround for 88SX60x1 FEr SATA#26: + * + * COMRESETs have to take care not to accidently + * put the drive to sleep when writing SCR_CONTROL. + * Setting bits 12..15 prevents this problem. + * + * So if we see an outbound COMMRESET, set those bits. + * Ditto for the followup write that clears the reset. + * + * The proprietary driver does this for + * all chip versions, and so do we. + */ + if ((val & 0xf) == 1 || (readl(addr) & 0xf) == 1) + val |= 0xf000; + } + writelfl(val, addr); return 0; } else return -EINVAL; @@ -1032,47 +1367,196 @@ static void mv6_dev_config(struct ata_device *adev) * * Gen-II does not support NCQ over a port multiplier * (no FIS-based switching). - * - * We don't have hob_nsect when doing NCQ commands on Gen-II. - * See mv_qc_prep() for more info. */ if (adev->flags & ATA_DFLAG_NCQ) { if (sata_pmp_attached(adev->link->ap)) { adev->flags &= ~ATA_DFLAG_NCQ; ata_dev_printk(adev, KERN_INFO, "NCQ disabled for command-based switching\n"); - } else if (adev->max_sectors > GEN_II_NCQ_MAX_SECTORS) { - adev->max_sectors = GEN_II_NCQ_MAX_SECTORS; - ata_dev_printk(adev, KERN_INFO, - "max_sectors limited to %u for NCQ\n", - adev->max_sectors); } } } -static void mv_config_fbs(void __iomem *port_mmio, int enable_fbs) +static int mv_qc_defer(struct ata_queued_cmd *qc) { - u32 old_fcfg, new_fcfg, old_ltmode, new_ltmode; + struct ata_link *link = qc->dev->link; + struct ata_port *ap = link->ap; + struct mv_port_priv *pp = ap->private_data; + /* - * Various bit settings required for operation - * in FIS-based switching (fbs) mode on GenIIe: + * Don't allow new commands if we're in a delayed EH state + * for NCQ and/or FIS-based switching. */ - old_fcfg = readl(port_mmio + FIS_CFG_OFS); - old_ltmode = readl(port_mmio + LTMODE_OFS); - if (enable_fbs) { - new_fcfg = old_fcfg | FIS_CFG_SINGLE_SYNC; - new_ltmode = old_ltmode | LTMODE_BIT8; - } else { /* disable fbs */ - new_fcfg = old_fcfg & ~FIS_CFG_SINGLE_SYNC; - new_ltmode = old_ltmode & ~LTMODE_BIT8; + if (pp->pp_flags & MV_PP_FLAG_DELAYED_EH) + return ATA_DEFER_PORT; + + /* PIO commands need exclusive link: no other commands [DMA or PIO] + * can run concurrently. + * set excl_link when we want to send a PIO command in DMA mode + * or a non-NCQ command in NCQ mode. + * When we receive a command from that link, and there are no + * outstanding commands, mark a flag to clear excl_link and let + * the command go through. + */ + if (unlikely(ap->excl_link)) { + if (link == ap->excl_link) { + if (ap->nr_active_links) + return ATA_DEFER_PORT; + qc->flags |= ATA_QCFLAG_CLEAR_EXCL; + return 0; + } else + return ATA_DEFER_PORT; } - if (new_fcfg != old_fcfg) - writelfl(new_fcfg, port_mmio + FIS_CFG_OFS); - if (new_ltmode != old_ltmode) - writelfl(new_ltmode, port_mmio + LTMODE_OFS); + + /* + * If the port is completely idle, then allow the new qc. + */ + if (ap->nr_active_links == 0) + return 0; + + /* + * The port is operating in host queuing mode (EDMA) with NCQ + * enabled, allow multiple NCQ commands. EDMA also allows + * queueing multiple DMA commands but libata core currently + * doesn't allow it. + */ + if ((pp->pp_flags & MV_PP_FLAG_EDMA_EN) && + (pp->pp_flags & MV_PP_FLAG_NCQ_EN)) { + if (ata_is_ncq(qc->tf.protocol)) + return 0; + else { + ap->excl_link = link; + return ATA_DEFER_PORT; + } + } + + return ATA_DEFER_PORT; } -static void mv_edma_cfg(struct ata_port *ap, int want_ncq) +static void mv_config_fbs(struct ata_port *ap, int want_ncq, int want_fbs) +{ + struct mv_port_priv *pp = ap->private_data; + void __iomem *port_mmio; + + u32 fiscfg, *old_fiscfg = &pp->cached.fiscfg; + u32 ltmode, *old_ltmode = &pp->cached.ltmode; + u32 haltcond, *old_haltcond = &pp->cached.haltcond; + + ltmode = *old_ltmode & ~LTMODE_BIT8; + haltcond = *old_haltcond | EDMA_ERR_DEV; + + if (want_fbs) { + fiscfg = *old_fiscfg | FISCFG_SINGLE_SYNC; + ltmode = *old_ltmode | LTMODE_BIT8; + if (want_ncq) + haltcond &= ~EDMA_ERR_DEV; + else + fiscfg |= FISCFG_WAIT_DEV_ERR; + } else { + fiscfg = *old_fiscfg & ~(FISCFG_SINGLE_SYNC | FISCFG_WAIT_DEV_ERR); + } + + port_mmio = mv_ap_base(ap); + mv_write_cached_reg(port_mmio + FISCFG, old_fiscfg, fiscfg); + mv_write_cached_reg(port_mmio + LTMODE, old_ltmode, ltmode); + mv_write_cached_reg(port_mmio + EDMA_HALTCOND, old_haltcond, haltcond); +} + +static void mv_60x1_errata_sata25(struct ata_port *ap, int want_ncq) +{ + struct mv_host_priv *hpriv = ap->host->private_data; + u32 old, new; + + /* workaround for 88SX60x1 FEr SATA#25 (part 1) */ + old = readl(hpriv->base + GPIO_PORT_CTL); + if (want_ncq) + new = old | (1 << 22); + else + new = old & ~(1 << 22); + if (new != old) + writel(new, hpriv->base + GPIO_PORT_CTL); +} + +/** + * mv_bmdma_enable - set a magic bit on GEN_IIE to allow bmdma + * @ap: Port being initialized + * + * There are two DMA modes on these chips: basic DMA, and EDMA. + * + * Bit-0 of the "EDMA RESERVED" register enables/disables use + * of basic DMA on the GEN_IIE versions of the chips. + * + * This bit survives EDMA resets, and must be set for basic DMA + * to function, and should be cleared when EDMA is active. + */ +static void mv_bmdma_enable_iie(struct ata_port *ap, int enable_bmdma) +{ + struct mv_port_priv *pp = ap->private_data; + u32 new, *old = &pp->cached.unknown_rsvd; + + if (enable_bmdma) + new = *old | 1; + else + new = *old & ~1; + mv_write_cached_reg(mv_ap_base(ap) + EDMA_UNKNOWN_RSVD, old, new); +} + +/* + * SOC chips have an issue whereby the HDD LEDs don't always blink + * during I/O when NCQ is enabled. Enabling a special "LED blink" mode + * of the SOC takes care of it, generating a steady blink rate when + * any drive on the chip is active. + * + * Unfortunately, the blink mode is a global hardware setting for the SOC, + * so we must use it whenever at least one port on the SOC has NCQ enabled. + * + * We turn "LED blink" off when NCQ is not in use anywhere, because the normal + * LED operation works then, and provides better (more accurate) feedback. + * + * Note that this code assumes that an SOC never has more than one HC onboard. + */ +static void mv_soc_led_blink_enable(struct ata_port *ap) +{ + struct ata_host *host = ap->host; + struct mv_host_priv *hpriv = host->private_data; + void __iomem *hc_mmio; + u32 led_ctrl; + + if (hpriv->hp_flags & MV_HP_QUIRK_LED_BLINK_EN) + return; + hpriv->hp_flags |= MV_HP_QUIRK_LED_BLINK_EN; + hc_mmio = mv_hc_base_from_port(mv_host_base(host), ap->port_no); + led_ctrl = readl(hc_mmio + SOC_LED_CTRL); + writel(led_ctrl | SOC_LED_CTRL_BLINK, hc_mmio + SOC_LED_CTRL); +} + +static void mv_soc_led_blink_disable(struct ata_port *ap) +{ + struct ata_host *host = ap->host; + struct mv_host_priv *hpriv = host->private_data; + void __iomem *hc_mmio; + u32 led_ctrl; + unsigned int port; + + if (!(hpriv->hp_flags & MV_HP_QUIRK_LED_BLINK_EN)) + return; + + /* disable led-blink only if no ports are using NCQ */ + for (port = 0; port < hpriv->n_ports; port++) { + struct ata_port *this_ap = host->ports[port]; + struct mv_port_priv *pp = this_ap->private_data; + + if (pp->pp_flags & MV_PP_FLAG_NCQ_EN) + return; + } + + hpriv->hp_flags &= ~MV_HP_QUIRK_LED_BLINK_EN; + hc_mmio = mv_hc_base_from_port(mv_host_base(host), ap->port_no); + led_ctrl = readl(hc_mmio + SOC_LED_CTRL); + writel(led_ctrl & ~SOC_LED_CTRL_BLINK, hc_mmio + SOC_LED_CTRL); +} + +static void mv_edma_cfg(struct ata_port *ap, int want_ncq, int want_edma) { u32 cfg; struct mv_port_priv *pp = ap->private_data; @@ -1081,34 +1565,59 @@ static void mv_edma_cfg(struct ata_port *ap, int want_ncq) /* set up non-NCQ EDMA configuration */ cfg = EDMA_CFG_Q_DEPTH; /* always 0x1f for *all* chips */ + pp->pp_flags &= + ~(MV_PP_FLAG_FBS_EN | MV_PP_FLAG_NCQ_EN | MV_PP_FLAG_FAKE_ATA_BUSY); if (IS_GEN_I(hpriv)) cfg |= (1 << 8); /* enab config burst size mask */ - else if (IS_GEN_II(hpriv)) + else if (IS_GEN_II(hpriv)) { cfg |= EDMA_CFG_RD_BRST_EXT | EDMA_CFG_WR_BUFF_LEN; + mv_60x1_errata_sata25(ap, want_ncq); - else if (IS_GEN_IIE(hpriv)) { - cfg |= (1 << 23); /* do not mask PM field in rx'd FIS */ - cfg |= (1 << 22); /* enab 4-entry host queue cache */ - cfg |= (1 << 18); /* enab early completion */ - cfg |= (1 << 17); /* enab cut-through (dis stor&forwrd) */ + } else if (IS_GEN_IIE(hpriv)) { + int want_fbs = sata_pmp_attached(ap); + /* + * Possible future enhancement: + * + * The chip can use FBS with non-NCQ, if we allow it, + * But first we need to have the error handling in place + * for this mode (datasheet section 7.3.15.4.2.3). + * So disallow non-NCQ FBS for now. + */ + want_fbs &= want_ncq; - if (want_ncq && sata_pmp_attached(ap)) { + mv_config_fbs(ap, want_ncq, want_fbs); + + if (want_fbs) { + pp->pp_flags |= MV_PP_FLAG_FBS_EN; cfg |= EDMA_CFG_EDMA_FBS; /* FIS-based switching */ - mv_config_fbs(port_mmio, 1); - } else { - mv_config_fbs(port_mmio, 0); + } + + cfg |= (1 << 23); /* do not mask PM field in rx'd FIS */ + if (want_edma) { + cfg |= (1 << 22); /* enab 4-entry host queue cache */ + if (!IS_SOC(hpriv)) + cfg |= (1 << 18); /* enab early completion */ + } + if (hpriv->hp_flags & MV_HP_CUT_THROUGH) + cfg |= (1 << 17); /* enab cut-thru (dis stor&forwrd) */ + mv_bmdma_enable_iie(ap, !want_edma); + + if (IS_SOC(hpriv)) { + if (want_ncq) + mv_soc_led_blink_enable(ap); + else + mv_soc_led_blink_disable(ap); } } if (want_ncq) { cfg |= EDMA_CFG_NCQ; pp->pp_flags |= MV_PP_FLAG_NCQ_EN; - } else - pp->pp_flags &= ~MV_PP_FLAG_NCQ_EN; + } - writelfl(cfg, port_mmio + EDMA_CFG_OFS); + writelfl(cfg, port_mmio + EDMA_CFG); } static void mv_port_free_dma_mem(struct ata_port *ap) @@ -1155,6 +1664,7 @@ static int mv_port_start(struct ata_port *ap) struct device *dev = ap->host->dev; struct mv_host_priv *hpriv = ap->host->private_data; struct mv_port_priv *pp; + unsigned long flags; int tag; pp = devm_kzalloc(dev, sizeof(*pp), GFP_KERNEL); @@ -1172,6 +1682,9 @@ static int mv_port_start(struct ata_port *ap) goto out_port_free_dma_mem; memset(pp->crpb, 0, MV_CRPB_Q_SZ); + /* 6041/6081 Rev. "C0" (and newer) are okay with async notify */ + if (hpriv->hp_flags & MV_HP_ERRATA_60X1C0) + ap->flags |= ATA_FLAG_AN; /* * For GEN_I, there's no NCQ, so we only allocate a single sg_tbl. * For later hardware, we need one unique sg_tbl per NCQ tag. @@ -1187,6 +1700,12 @@ static int mv_port_start(struct ata_port *ap) pp->sg_tbl_dma[tag] = pp->sg_tbl_dma[0]; } } + + spin_lock_irqsave(ap->lock, flags); + mv_save_cached_regs(ap); + mv_edma_cfg(ap, 0, 0); + spin_unlock_irqrestore(ap->lock, flags); + return 0; out_port_free_dma_mem: @@ -1205,7 +1724,12 @@ out_port_free_dma_mem: */ static void mv_port_stop(struct ata_port *ap) { + unsigned long flags; + + spin_lock_irqsave(ap->lock, flags); mv_stop_edma(ap); + mv_enable_port_irqs(ap, 0); + spin_unlock_irqrestore(ap->lock, flags); mv_port_free_dma_mem(ap); } @@ -1234,12 +1758,13 @@ static void mv_fill_sg(struct ata_queued_cmd *qc) u32 offset = addr & 0xffff; u32 len = sg_len; - if ((offset + sg_len > 0x10000)) + if (offset + len > 0x10000) len = 0x10000 - offset; mv_sg->addr = cpu_to_le32(addr & 0xffffffff); mv_sg->addr_hi = cpu_to_le32((addr >> 16) >> 16); mv_sg->flags_size = cpu_to_le32(len & 0xffff); + mv_sg->reserved = 0; sg_len -= len; addr += len; @@ -1251,6 +1776,7 @@ static void mv_fill_sg(struct ata_queued_cmd *qc) if (likely(last_sg)) last_sg->flags_size |= cpu_to_le32(EPRD_FLAG_END_OF_TBL); + mb(); /* ensure data structure is visible to the chipset */ } static void mv_crqb_pack_cmd(__le16 *cmdw, u8 data, u8 addr, unsigned last) @@ -1261,6 +1787,180 @@ static void mv_crqb_pack_cmd(__le16 *cmdw, u8 data, u8 addr, unsigned last) } /** + * mv_sff_irq_clear - Clear hardware interrupt after DMA. + * @ap: Port associated with this ATA transaction. + * + * We need this only for ATAPI bmdma transactions, + * as otherwise we experience spurious interrupts + * after libata-sff handles the bmdma interrupts. + */ +static void mv_sff_irq_clear(struct ata_port *ap) +{ + mv_clear_and_enable_port_irqs(ap, mv_ap_base(ap), ERR_IRQ); +} + +/** + * mv_check_atapi_dma - Filter ATAPI cmds which are unsuitable for DMA. + * @qc: queued command to check for chipset/DMA compatibility. + * + * The bmdma engines cannot handle speculative data sizes + * (bytecount under/over flow). So only allow DMA for + * data transfer commands with known data sizes. + * + * LOCKING: + * Inherited from caller. + */ +static int mv_check_atapi_dma(struct ata_queued_cmd *qc) +{ + struct scsi_cmnd *scmd = qc->scsicmd; + + if (scmd) { + switch (scmd->cmnd[0]) { + case READ_6: + case READ_10: + case READ_12: + case WRITE_6: + case WRITE_10: + case WRITE_12: + case GPCMD_READ_CD: + case GPCMD_SEND_DVD_STRUCTURE: + case GPCMD_SEND_CUE_SHEET: + return 0; /* DMA is safe */ + } + } + return -EOPNOTSUPP; /* use PIO instead */ +} + +/** + * mv_bmdma_setup - Set up BMDMA transaction + * @qc: queued command to prepare DMA for. + * + * LOCKING: + * Inherited from caller. + */ +static void mv_bmdma_setup(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + void __iomem *port_mmio = mv_ap_base(ap); + struct mv_port_priv *pp = ap->private_data; + + mv_fill_sg(qc); + + /* clear all DMA cmd bits */ + writel(0, port_mmio + BMDMA_CMD); + + /* load PRD table addr. */ + writel((pp->sg_tbl_dma[qc->tag] >> 16) >> 16, + port_mmio + BMDMA_PRD_HIGH); + writelfl(pp->sg_tbl_dma[qc->tag], + port_mmio + BMDMA_PRD_LOW); + + /* issue r/w command */ + ap->ops->sff_exec_command(ap, &qc->tf); +} + +/** + * mv_bmdma_start - Start a BMDMA transaction + * @qc: queued command to start DMA on. + * + * LOCKING: + * Inherited from caller. + */ +static void mv_bmdma_start(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + void __iomem *port_mmio = mv_ap_base(ap); + unsigned int rw = (qc->tf.flags & ATA_TFLAG_WRITE); + u32 cmd = (rw ? 0 : ATA_DMA_WR) | ATA_DMA_START; + + /* start host DMA transaction */ + writelfl(cmd, port_mmio + BMDMA_CMD); +} + +/** + * mv_bmdma_stop - Stop BMDMA transfer + * @qc: queued command to stop DMA on. + * + * Clears the ATA_DMA_START flag in the bmdma control register + * + * LOCKING: + * Inherited from caller. + */ +static void mv_bmdma_stop(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + void __iomem *port_mmio = mv_ap_base(ap); + u32 cmd; + + /* clear start/stop bit */ + cmd = readl(port_mmio + BMDMA_CMD); + cmd &= ~ATA_DMA_START; + writelfl(cmd, port_mmio + BMDMA_CMD); + + /* one-PIO-cycle guaranteed wait, per spec, for HDMA1:0 transition */ + ata_sff_dma_pause(ap); +} + +/** + * mv_bmdma_status - Read BMDMA status + * @ap: port for which to retrieve DMA status. + * + * Read and return equivalent of the sff BMDMA status register. + * + * LOCKING: + * Inherited from caller. + */ +static u8 mv_bmdma_status(struct ata_port *ap) +{ + void __iomem *port_mmio = mv_ap_base(ap); + u32 reg, status; + + /* + * Other bits are valid only if ATA_DMA_ACTIVE==0, + * and the ATA_DMA_INTR bit doesn't exist. + */ + reg = readl(port_mmio + BMDMA_STATUS); + if (reg & ATA_DMA_ACTIVE) + status = ATA_DMA_ACTIVE; + else + status = (reg & ATA_DMA_ERR) | ATA_DMA_INTR; + return status; +} + +static void mv_rw_multi_errata_sata24(struct ata_queued_cmd *qc) +{ + struct ata_taskfile *tf = &qc->tf; + /* + * Workaround for 88SX60x1 FEr SATA#24. + * + * Chip may corrupt WRITEs if multi_count >= 4kB. + * Note that READs are unaffected. + * + * It's not clear if this errata really means "4K bytes", + * or if it always happens for multi_count > 7 + * regardless of device sector_size. + * + * So, for safety, any write with multi_count > 7 + * gets converted here into a regular PIO write instead: + */ + if ((tf->flags & ATA_TFLAG_WRITE) && is_multi_taskfile(tf)) { + if (qc->dev->multi_count > 7) { + switch (tf->command) { + case ATA_CMD_WRITE_MULTI: + tf->command = ATA_CMD_PIO_WRITE; + break; + case ATA_CMD_WRITE_MULTI_FUA_EXT: + tf->flags &= ~ATA_TFLAG_FUA; /* ugh */ + /* fall through */ + case ATA_CMD_WRITE_MULTI_EXT: + tf->command = ATA_CMD_PIO_WRITE_EXT; + break; + } + } + } +} + +/** * mv_qc_prep - Host specific command preparation. * @qc: queued command to prepare * @@ -1277,24 +1977,31 @@ static void mv_qc_prep(struct ata_queued_cmd *qc) struct ata_port *ap = qc->ap; struct mv_port_priv *pp = ap->private_data; __le16 *cw; - struct ata_taskfile *tf; + struct ata_taskfile *tf = &qc->tf; u16 flags = 0; unsigned in_index; - if ((qc->tf.protocol != ATA_PROT_DMA) && - (qc->tf.protocol != ATA_PROT_NCQ)) + switch (tf->protocol) { + case ATA_PROT_DMA: + case ATA_PROT_NCQ: + break; /* continue below */ + case ATA_PROT_PIO: + mv_rw_multi_errata_sata24(qc); return; + default: + return; + } /* Fill in command request block */ - if (!(qc->tf.flags & ATA_TFLAG_WRITE)) + if (!(tf->flags & ATA_TFLAG_WRITE)) flags |= CRQB_FLAG_READ; WARN_ON(MV_MAX_Q_DEPTH <= qc->tag); flags |= qc->tag << CRQB_TAG_SHIFT; flags |= (qc->dev->link->pmp & 0xf) << CRQB_PMP_SHIFT; /* get current queue index from software */ - in_index = pp->req_idx & MV_MAX_Q_DEPTH_MASK; + in_index = pp->req_idx; pp->crqb[in_index].sg_addr = cpu_to_le32(pp->sg_tbl_dma[qc->tag] & 0xffffffff); @@ -1303,13 +2010,13 @@ static void mv_qc_prep(struct ata_queued_cmd *qc) pp->crqb[in_index].ctrl_flags = cpu_to_le16(flags); cw = &pp->crqb[in_index].ata_cmd[0]; - tf = &qc->tf; /* Sadly, the CRQB cannot accomodate all registers--there are * only 11 bytes...so we must pick and choose required * registers based on the command. So, we drop feature and * hob_feature for [RW] DMA commands, but they are needed for - * NCQ. NCQ will drop hob_nsect. + * NCQ. NCQ will drop hob_nsect, which is not needed there + * (nsect is used only for the tag; feat/hob_feat hold true nsect). */ switch (tf->command) { case ATA_CMD_READ: @@ -1368,16 +2075,16 @@ static void mv_qc_prep_iie(struct ata_queued_cmd *qc) struct ata_port *ap = qc->ap; struct mv_port_priv *pp = ap->private_data; struct mv_crqb_iie *crqb; - struct ata_taskfile *tf; + struct ata_taskfile *tf = &qc->tf; unsigned in_index; u32 flags = 0; - if ((qc->tf.protocol != ATA_PROT_DMA) && - (qc->tf.protocol != ATA_PROT_NCQ)) + if ((tf->protocol != ATA_PROT_DMA) && + (tf->protocol != ATA_PROT_NCQ)) return; /* Fill in Gen IIE command request block */ - if (!(qc->tf.flags & ATA_TFLAG_WRITE)) + if (!(tf->flags & ATA_TFLAG_WRITE)) flags |= CRQB_FLAG_READ; WARN_ON(MV_MAX_Q_DEPTH <= qc->tag); @@ -1386,14 +2093,13 @@ static void mv_qc_prep_iie(struct ata_queued_cmd *qc) flags |= (qc->dev->link->pmp & 0xf) << CRQB_PMP_SHIFT; /* get current queue index from software */ - in_index = pp->req_idx & MV_MAX_Q_DEPTH_MASK; + in_index = pp->req_idx; crqb = (struct mv_crqb_iie *) &pp->crqb[in_index]; crqb->addr = cpu_to_le32(pp->sg_tbl_dma[qc->tag] & 0xffffffff); crqb->addr_hi = cpu_to_le32((pp->sg_tbl_dma[qc->tag] >> 16) >> 16); crqb->flags = cpu_to_le32(flags); - tf = &qc->tf; crqb->ata_cmd[0] = cpu_to_le32( (tf->command << 16) | (tf->feature << 24) @@ -1421,6 +2127,132 @@ static void mv_qc_prep_iie(struct ata_queued_cmd *qc) } /** + * mv_sff_check_status - fetch device status, if valid + * @ap: ATA port to fetch status from + * + * When using command issue via mv_qc_issue_fis(), + * the initial ATA_BUSY state does not show up in the + * ATA status (shadow) register. This can confuse libata! + * + * So we have a hook here to fake ATA_BUSY for that situation, + * until the first time a BUSY, DRQ, or ERR bit is seen. + * + * The rest of the time, it simply returns the ATA status register. + */ +static u8 mv_sff_check_status(struct ata_port *ap) +{ + u8 stat = ioread8(ap->ioaddr.status_addr); + struct mv_port_priv *pp = ap->private_data; + + if (pp->pp_flags & MV_PP_FLAG_FAKE_ATA_BUSY) { + if (stat & (ATA_BUSY | ATA_DRQ | ATA_ERR)) + pp->pp_flags &= ~MV_PP_FLAG_FAKE_ATA_BUSY; + else + stat = ATA_BUSY; + } + return stat; +} + +/** + * mv_send_fis - Send a FIS, using the "Vendor-Unique FIS" register + * @fis: fis to be sent + * @nwords: number of 32-bit words in the fis + */ +static unsigned int mv_send_fis(struct ata_port *ap, u32 *fis, int nwords) +{ + void __iomem *port_mmio = mv_ap_base(ap); + u32 ifctl, old_ifctl, ifstat; + int i, timeout = 200, final_word = nwords - 1; + + /* Initiate FIS transmission mode */ + old_ifctl = readl(port_mmio + SATA_IFCTL); + ifctl = 0x100 | (old_ifctl & 0xf); + writelfl(ifctl, port_mmio + SATA_IFCTL); + + /* Send all words of the FIS except for the final word */ + for (i = 0; i < final_word; ++i) + writel(fis[i], port_mmio + VENDOR_UNIQUE_FIS); + + /* Flag end-of-transmission, and then send the final word */ + writelfl(ifctl | 0x200, port_mmio + SATA_IFCTL); + writelfl(fis[final_word], port_mmio + VENDOR_UNIQUE_FIS); + + /* + * Wait for FIS transmission to complete. + * This typically takes just a single iteration. + */ + do { + ifstat = readl(port_mmio + SATA_IFSTAT); + } while (!(ifstat & 0x1000) && --timeout); + + /* Restore original port configuration */ + writelfl(old_ifctl, port_mmio + SATA_IFCTL); + + /* See if it worked */ + if ((ifstat & 0x3000) != 0x1000) { + ata_port_printk(ap, KERN_WARNING, + "%s transmission error, ifstat=%08x\n", + __func__, ifstat); + return AC_ERR_OTHER; + } + return 0; +} + +/** + * mv_qc_issue_fis - Issue a command directly as a FIS + * @qc: queued command to start + * + * Note that the ATA shadow registers are not updated + * after command issue, so the device will appear "READY" + * if polled, even while it is BUSY processing the command. + * + * So we use a status hook to fake ATA_BUSY until the drive changes state. + * + * Note: we don't get updated shadow regs on *completion* + * of non-data commands. So avoid sending them via this function, + * as they will appear to have completed immediately. + * + * GEN_IIE has special registers that we could get the result tf from, + * but earlier chipsets do not. For now, we ignore those registers. + */ +static unsigned int mv_qc_issue_fis(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + struct mv_port_priv *pp = ap->private_data; + struct ata_link *link = qc->dev->link; + u32 fis[5]; + int err = 0; + + ata_tf_to_fis(&qc->tf, link->pmp, 1, (void *)fis); + err = mv_send_fis(ap, fis, ARRAY_SIZE(fis)); + if (err) + return err; + + switch (qc->tf.protocol) { + case ATAPI_PROT_PIO: + pp->pp_flags |= MV_PP_FLAG_FAKE_ATA_BUSY; + /* fall through */ + case ATAPI_PROT_NODATA: + ap->hsm_task_state = HSM_ST_FIRST; + break; + case ATA_PROT_PIO: + pp->pp_flags |= MV_PP_FLAG_FAKE_ATA_BUSY; + if (qc->tf.flags & ATA_TFLAG_WRITE) + ap->hsm_task_state = HSM_ST_FIRST; + else + ap->hsm_task_state = HSM_ST; + break; + default: + ap->hsm_task_state = HSM_ST_LAST; + break; + } + + if (qc->tf.flags & ATA_TFLAG_POLLING) + ata_pio_queue_task(ap, qc, 0); + return 0; +} + +/** * mv_qc_issue - Initiate a command to the host * @qc: queued command to start * @@ -1434,79 +2266,372 @@ static void mv_qc_prep_iie(struct ata_queued_cmd *qc) */ static unsigned int mv_qc_issue(struct ata_queued_cmd *qc) { + static int limit_warnings = 10; struct ata_port *ap = qc->ap; void __iomem *port_mmio = mv_ap_base(ap); struct mv_port_priv *pp = ap->private_data; u32 in_index; + unsigned int port_irqs; - if ((qc->tf.protocol != ATA_PROT_DMA) && - (qc->tf.protocol != ATA_PROT_NCQ)) { + pp->pp_flags &= ~MV_PP_FLAG_FAKE_ATA_BUSY; /* paranoia */ + + switch (qc->tf.protocol) { + case ATA_PROT_DMA: + case ATA_PROT_NCQ: + mv_start_edma(ap, port_mmio, pp, qc->tf.protocol); + pp->req_idx = (pp->req_idx + 1) & MV_MAX_Q_DEPTH_MASK; + in_index = pp->req_idx << EDMA_REQ_Q_PTR_SHIFT; + + /* Write the request in pointer to kick the EDMA to life */ + writelfl((pp->crqb_dma & EDMA_REQ_Q_BASE_LO_MASK) | in_index, + port_mmio + EDMA_REQ_Q_IN_PTR); + return 0; + + case ATA_PROT_PIO: /* - * We're about to send a non-EDMA capable command to the - * port. Turn off EDMA so there won't be problems accessing - * shadow block, etc registers. + * Errata SATA#16, SATA#24: warn if multiple DRQs expected. + * + * Someday, we might implement special polling workarounds + * for these, but it all seems rather unnecessary since we + * normally use only DMA for commands which transfer more + * than a single block of data. + * + * Much of the time, this could just work regardless. + * So for now, just log the incident, and allow the attempt. */ + if (limit_warnings > 0 && (qc->nbytes / qc->sect_size) > 1) { + --limit_warnings; + ata_link_printk(qc->dev->link, KERN_WARNING, DRV_NAME + ": attempting PIO w/multiple DRQ: " + "this may fail due to h/w errata\n"); + } + /* drop through */ + case ATA_PROT_NODATA: + case ATAPI_PROT_PIO: + case ATAPI_PROT_NODATA: + if (ap->flags & ATA_FLAG_PIO_POLLING) + qc->tf.flags |= ATA_TFLAG_POLLING; + break; + } + + if (qc->tf.flags & ATA_TFLAG_POLLING) + port_irqs = ERR_IRQ; /* mask device interrupt when polling */ + else + port_irqs = ERR_IRQ | DONE_IRQ; /* unmask all interrupts */ + + /* + * We're about to send a non-EDMA capable command to the + * port. Turn off EDMA so there won't be problems accessing + * shadow block, etc registers. + */ + mv_stop_edma(ap); + mv_clear_and_enable_port_irqs(ap, mv_ap_base(ap), port_irqs); + mv_pmp_select(ap, qc->dev->link->pmp); + + if (qc->tf.command == ATA_CMD_READ_LOG_EXT) { + struct mv_host_priv *hpriv = ap->host->private_data; + /* + * Workaround for 88SX60x1 FEr SATA#25 (part 2). + * + * After any NCQ error, the READ_LOG_EXT command + * from libata-eh *must* use mv_qc_issue_fis(). + * Otherwise it might fail, due to chip errata. + * + * Rather than special-case it, we'll just *always* + * use this method here for READ_LOG_EXT, making for + * easier testing. + */ + if (IS_GEN_II(hpriv)) + return mv_qc_issue_fis(qc); + } + return ata_sff_qc_issue(qc); +} + +static struct ata_queued_cmd *mv_get_active_qc(struct ata_port *ap) +{ + struct mv_port_priv *pp = ap->private_data; + struct ata_queued_cmd *qc; + + if (pp->pp_flags & MV_PP_FLAG_NCQ_EN) + return NULL; + qc = ata_qc_from_tag(ap, ap->link.active_tag); + if (qc) { + if (qc->tf.flags & ATA_TFLAG_POLLING) + qc = NULL; + else if (!(qc->flags & ATA_QCFLAG_ACTIVE)) + qc = NULL; + } + return qc; +} + +static void mv_pmp_error_handler(struct ata_port *ap) +{ + unsigned int pmp, pmp_map; + struct mv_port_priv *pp = ap->private_data; + + if (pp->pp_flags & MV_PP_FLAG_DELAYED_EH) { + /* + * Perform NCQ error analysis on failed PMPs + * before we freeze the port entirely. + * + * The failed PMPs are marked earlier by mv_pmp_eh_prep(). + */ + pmp_map = pp->delayed_eh_pmp_map; + pp->pp_flags &= ~MV_PP_FLAG_DELAYED_EH; + for (pmp = 0; pmp_map != 0; pmp++) { + unsigned int this_pmp = (1 << pmp); + if (pmp_map & this_pmp) { + struct ata_link *link = &ap->pmp_link[pmp]; + pmp_map &= ~this_pmp; + ata_eh_analyze_ncq_error(link); + } + } + ata_port_freeze(ap); + } + sata_pmp_error_handler(ap); +} + +static unsigned int mv_get_err_pmp_map(struct ata_port *ap) +{ + void __iomem *port_mmio = mv_ap_base(ap); + + return readl(port_mmio + SATA_TESTCTL) >> 16; +} + +static void mv_pmp_eh_prep(struct ata_port *ap, unsigned int pmp_map) +{ + struct ata_eh_info *ehi; + unsigned int pmp; + + /* + * Initialize EH info for PMPs which saw device errors + */ + ehi = &ap->link.eh_info; + for (pmp = 0; pmp_map != 0; pmp++) { + unsigned int this_pmp = (1 << pmp); + if (pmp_map & this_pmp) { + struct ata_link *link = &ap->pmp_link[pmp]; + + pmp_map &= ~this_pmp; + ehi = &link->eh_info; + ata_ehi_clear_desc(ehi); + ata_ehi_push_desc(ehi, "dev err"); + ehi->err_mask |= AC_ERR_DEV; + ehi->action |= ATA_EH_RESET; + ata_link_abort(link); + } + } +} + +static int mv_req_q_empty(struct ata_port *ap) +{ + void __iomem *port_mmio = mv_ap_base(ap); + u32 in_ptr, out_ptr; + + in_ptr = (readl(port_mmio + EDMA_REQ_Q_IN_PTR) + >> EDMA_REQ_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK; + out_ptr = (readl(port_mmio + EDMA_REQ_Q_OUT_PTR) + >> EDMA_REQ_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK; + return (in_ptr == out_ptr); /* 1 == queue_is_empty */ +} + +static int mv_handle_fbs_ncq_dev_err(struct ata_port *ap) +{ + struct mv_port_priv *pp = ap->private_data; + int failed_links; + unsigned int old_map, new_map; + + /* + * Device error during FBS+NCQ operation: + * + * Set a port flag to prevent further I/O being enqueued. + * Leave the EDMA running to drain outstanding commands from this port. + * Perform the post-mortem/EH only when all responses are complete. + * Follow recovery sequence from 6042/7042 datasheet (7.3.15.4.2.2). + */ + if (!(pp->pp_flags & MV_PP_FLAG_DELAYED_EH)) { + pp->pp_flags |= MV_PP_FLAG_DELAYED_EH; + pp->delayed_eh_pmp_map = 0; + } + old_map = pp->delayed_eh_pmp_map; + new_map = old_map | mv_get_err_pmp_map(ap); + + if (old_map != new_map) { + pp->delayed_eh_pmp_map = new_map; + mv_pmp_eh_prep(ap, new_map & ~old_map); + } + failed_links = hweight16(new_map); + + ata_port_printk(ap, KERN_INFO, "%s: pmp_map=%04x qc_map=%04x " + "failed_links=%d nr_active_links=%d\n", + __func__, pp->delayed_eh_pmp_map, + ap->qc_active, failed_links, + ap->nr_active_links); + + if (ap->nr_active_links <= failed_links && mv_req_q_empty(ap)) { + mv_process_crpb_entries(ap, pp); mv_stop_edma(ap); - mv_pmp_select(ap, qc->dev->link->pmp); - return ata_sff_qc_issue(qc); + mv_eh_freeze(ap); + ata_port_printk(ap, KERN_INFO, "%s: done\n", __func__); + return 1; /* handled */ } + ata_port_printk(ap, KERN_INFO, "%s: waiting\n", __func__); + return 1; /* handled */ +} + +static int mv_handle_fbs_non_ncq_dev_err(struct ata_port *ap) +{ + /* + * Possible future enhancement: + * + * FBS+non-NCQ operation is not yet implemented. + * See related notes in mv_edma_cfg(). + * + * Device error during FBS+non-NCQ operation: + * + * We need to snapshot the shadow registers for each failed command. + * Follow recovery sequence from 6042/7042 datasheet (7.3.15.4.2.3). + */ + return 0; /* not handled */ +} - mv_start_dma(ap, port_mmio, pp, qc->tf.protocol); +static int mv_handle_dev_err(struct ata_port *ap, u32 edma_err_cause) +{ + struct mv_port_priv *pp = ap->private_data; - pp->req_idx++; + if (!(pp->pp_flags & MV_PP_FLAG_EDMA_EN)) + return 0; /* EDMA was not active: not handled */ + if (!(pp->pp_flags & MV_PP_FLAG_FBS_EN)) + return 0; /* FBS was not active: not handled */ - in_index = (pp->req_idx & MV_MAX_Q_DEPTH_MASK) << EDMA_REQ_Q_PTR_SHIFT; + if (!(edma_err_cause & EDMA_ERR_DEV)) + return 0; /* non DEV error: not handled */ + edma_err_cause &= ~EDMA_ERR_IRQ_TRANSIENT; + if (edma_err_cause & ~(EDMA_ERR_DEV | EDMA_ERR_SELF_DIS)) + return 0; /* other problems: not handled */ - /* and write the request in pointer to kick the EDMA to life */ - writelfl((pp->crqb_dma & EDMA_REQ_Q_BASE_LO_MASK) | in_index, - port_mmio + EDMA_REQ_Q_IN_PTR_OFS); + if (pp->pp_flags & MV_PP_FLAG_NCQ_EN) { + /* + * EDMA should NOT have self-disabled for this case. + * If it did, then something is wrong elsewhere, + * and we cannot handle it here. + */ + if (edma_err_cause & EDMA_ERR_SELF_DIS) { + ata_port_printk(ap, KERN_WARNING, + "%s: err_cause=0x%x pp_flags=0x%x\n", + __func__, edma_err_cause, pp->pp_flags); + return 0; /* not handled */ + } + return mv_handle_fbs_ncq_dev_err(ap); + } else { + /* + * EDMA should have self-disabled for this case. + * If it did not, then something is wrong elsewhere, + * and we cannot handle it here. + */ + if (!(edma_err_cause & EDMA_ERR_SELF_DIS)) { + ata_port_printk(ap, KERN_WARNING, + "%s: err_cause=0x%x pp_flags=0x%x\n", + __func__, edma_err_cause, pp->pp_flags); + return 0; /* not handled */ + } + return mv_handle_fbs_non_ncq_dev_err(ap); + } + return 0; /* not handled */ +} - return 0; +static void mv_unexpected_intr(struct ata_port *ap, int edma_was_enabled) +{ + struct ata_eh_info *ehi = &ap->link.eh_info; + char *when = "idle"; + + ata_ehi_clear_desc(ehi); + if (ap->flags & ATA_FLAG_DISABLED) { + when = "disabled"; + } else if (edma_was_enabled) { + when = "EDMA enabled"; + } else { + struct ata_queued_cmd *qc = ata_qc_from_tag(ap, ap->link.active_tag); + if (qc && (qc->tf.flags & ATA_TFLAG_POLLING)) + when = "polling"; + } + ata_ehi_push_desc(ehi, "unexpected device interrupt while %s", when); + ehi->err_mask |= AC_ERR_OTHER; + ehi->action |= ATA_EH_RESET; + ata_port_freeze(ap); } /** * mv_err_intr - Handle error interrupts on the port * @ap: ATA channel to manipulate - * @reset_allowed: bool: 0 == don't trigger from reset here * - * In most cases, just clear the interrupt and move on. However, - * some cases require an eDMA reset, which also performs a COMRESET. - * The SERR case requires a clear of pending errors in the SATA - * SERROR register. Finally, if the port disabled DMA, - * update our cached copy to match. + * Most cases require a full reset of the chip's state machine, + * which also performs a COMRESET. + * Also, if the port disabled DMA, update our cached copy to match. * * LOCKING: * Inherited from caller. */ -static void mv_err_intr(struct ata_port *ap, struct ata_queued_cmd *qc) +static void mv_err_intr(struct ata_port *ap) { void __iomem *port_mmio = mv_ap_base(ap); u32 edma_err_cause, eh_freeze_mask, serr = 0; + u32 fis_cause = 0; struct mv_port_priv *pp = ap->private_data; struct mv_host_priv *hpriv = ap->host->private_data; - unsigned int edma_enabled = (pp->pp_flags & MV_PP_FLAG_EDMA_EN); unsigned int action = 0, err_mask = 0; struct ata_eh_info *ehi = &ap->link.eh_info; + struct ata_queued_cmd *qc; + int abort = 0; - ata_ehi_clear_desc(ehi); + /* + * Read and clear the SError and err_cause bits. + * For GenIIe, if EDMA_ERR_TRANS_IRQ_7 is set, we also must read/clear + * the FIS_IRQ_CAUSE register before clearing edma_err_cause. + */ + sata_scr_read(&ap->link, SCR_ERROR, &serr); + sata_scr_write_flush(&ap->link, SCR_ERROR, serr); - if (!edma_enabled) { - /* just a guess: do we need to do this? should we - * expand this, and do it in all cases? - */ - sata_scr_read(&ap->link, SCR_ERROR, &serr); - sata_scr_write_flush(&ap->link, SCR_ERROR, serr); + edma_err_cause = readl(port_mmio + EDMA_ERR_IRQ_CAUSE); + if (IS_GEN_IIE(hpriv) && (edma_err_cause & EDMA_ERR_TRANS_IRQ_7)) { + fis_cause = readl(port_mmio + FIS_IRQ_CAUSE); + writelfl(~fis_cause, port_mmio + FIS_IRQ_CAUSE); } + writelfl(~edma_err_cause, port_mmio + EDMA_ERR_IRQ_CAUSE); - edma_err_cause = readl(port_mmio + EDMA_ERR_IRQ_CAUSE_OFS); - - ata_ehi_push_desc(ehi, "edma_err_cause=%08x", edma_err_cause); + if (edma_err_cause & EDMA_ERR_DEV) { + /* + * Device errors during FIS-based switching operation + * require special handling. + */ + if (mv_handle_dev_err(ap, edma_err_cause)) + return; + } + qc = mv_get_active_qc(ap); + ata_ehi_clear_desc(ehi); + ata_ehi_push_desc(ehi, "edma_err_cause=%08x pp_flags=%08x", + edma_err_cause, pp->pp_flags); + + if (IS_GEN_IIE(hpriv) && (edma_err_cause & EDMA_ERR_TRANS_IRQ_7)) { + ata_ehi_push_desc(ehi, "fis_cause=%08x", fis_cause); + if (fis_cause & FIS_IRQ_CAUSE_AN) { + u32 ec = edma_err_cause & + ~(EDMA_ERR_TRANS_IRQ_7 | EDMA_ERR_IRQ_TRANSIENT); + sata_async_notification(ap); + if (!ec) + return; /* Just an AN; no need for the nukes */ + ata_ehi_push_desc(ehi, "SDB notify"); + } + } /* * All generations share these EDMA error cause bits: */ - if (edma_err_cause & EDMA_ERR_DEV) + if (edma_err_cause & EDMA_ERR_DEV) { err_mask |= AC_ERR_DEV; + action |= ATA_EH_RESET; + ata_ehi_push_desc(ehi, "dev error"); + } if (edma_err_cause & (EDMA_ERR_D_PAR | EDMA_ERR_PRD_PAR | EDMA_ERR_CRQB_PAR | EDMA_ERR_CRPB_PAR | EDMA_ERR_INTRL_PAR)) { @@ -1538,16 +2663,12 @@ static void mv_err_intr(struct ata_port *ap, struct ata_queued_cmd *qc) ata_ehi_push_desc(ehi, "EDMA self-disable"); } if (edma_err_cause & EDMA_ERR_SERR) { - sata_scr_read(&ap->link, SCR_ERROR, &serr); - sata_scr_write_flush(&ap->link, SCR_ERROR, serr); - err_mask = AC_ERR_ATA_BUS; + ata_ehi_push_desc(ehi, "SError=%08x", serr); + err_mask |= AC_ERR_ATA_BUS; action |= ATA_EH_RESET; } } - /* Clear EDMA now that SERR cleanup done */ - writelfl(~edma_err_cause, port_mmio + EDMA_ERR_IRQ_CAUSE_OFS); - if (!err_mask) { err_mask = AC_ERR_OTHER; action |= ATA_EH_RESET; @@ -1561,185 +2682,213 @@ static void mv_err_intr(struct ata_port *ap, struct ata_queued_cmd *qc) else ehi->err_mask |= err_mask; - if (edma_err_cause & eh_freeze_mask) + if (err_mask == AC_ERR_DEV) { + /* + * Cannot do ata_port_freeze() here, + * because it would kill PIO access, + * which is needed for further diagnosis. + */ + mv_eh_freeze(ap); + abort = 1; + } else if (edma_err_cause & eh_freeze_mask) { + /* + * Note to self: ata_port_freeze() calls ata_port_abort() + */ ata_port_freeze(ap); - else - ata_port_abort(ap); + } else { + abort = 1; + } + + if (abort) { + if (qc) + ata_link_abort(qc->dev->link); + else + ata_port_abort(ap); + } } -static void mv_intr_pio(struct ata_port *ap) +static void mv_process_crpb_response(struct ata_port *ap, + struct mv_crpb *response, unsigned int tag, int ncq_enabled) { - struct ata_queued_cmd *qc; - u8 ata_status; - - /* ignore spurious intr if drive still BUSY */ - ata_status = readb(ap->ioaddr.status_addr); - if (unlikely(ata_status & ATA_BUSY)) - return; - - /* get active ATA command */ - qc = ata_qc_from_tag(ap, ap->link.active_tag); - if (unlikely(!qc)) /* no active tag */ - return; - if (qc->tf.flags & ATA_TFLAG_POLLING) /* polling; we don't own qc */ - return; + struct ata_queued_cmd *qc = ata_qc_from_tag(ap, tag); - /* and finally, complete the ATA command */ - qc->err_mask |= ac_err_mask(ata_status); - ata_qc_complete(qc); + if (qc) { + u8 ata_status; + u16 edma_status = le16_to_cpu(response->flags); + /* + * edma_status from a response queue entry: + * LSB is from EDMA_ERR_IRQ_CAUSE (non-NCQ only). + * MSB is saved ATA status from command completion. + */ + if (!ncq_enabled) { + u8 err_cause = edma_status & 0xff & ~EDMA_ERR_DEV; + if (err_cause) { + /* + * Error will be seen/handled by mv_err_intr(). + * So do nothing at all here. + */ + return; + } + } + ata_status = edma_status >> CRPB_FLAG_STATUS_SHIFT; + if (!ac_err_mask(ata_status)) + ata_qc_complete(qc); + /* else: leave it for mv_err_intr() */ + } else { + ata_port_printk(ap, KERN_ERR, "%s: no qc for tag=%d\n", + __func__, tag); + } } -static void mv_intr_edma(struct ata_port *ap) +static void mv_process_crpb_entries(struct ata_port *ap, struct mv_port_priv *pp) { void __iomem *port_mmio = mv_ap_base(ap); struct mv_host_priv *hpriv = ap->host->private_data; - struct mv_port_priv *pp = ap->private_data; - struct ata_queued_cmd *qc; - u32 out_index, in_index; + u32 in_index; bool work_done = false; + int ncq_enabled = (pp->pp_flags & MV_PP_FLAG_NCQ_EN); - /* get h/w response queue pointer */ - in_index = (readl(port_mmio + EDMA_RSP_Q_IN_PTR_OFS) + /* Get the hardware queue position index */ + in_index = (readl(port_mmio + EDMA_RSP_Q_IN_PTR) >> EDMA_RSP_Q_PTR_SHIFT) & MV_MAX_Q_DEPTH_MASK; - while (1) { - u16 status; + /* Process new responses from since the last time we looked */ + while (in_index != pp->resp_idx) { unsigned int tag; + struct mv_crpb *response = &pp->crpb[pp->resp_idx]; - /* get s/w response queue last-read pointer, and compare */ - out_index = pp->resp_idx & MV_MAX_Q_DEPTH_MASK; - if (in_index == out_index) - break; + pp->resp_idx = (pp->resp_idx + 1) & MV_MAX_Q_DEPTH_MASK; - /* 50xx: get active ATA command */ - if (IS_GEN_I(hpriv)) + if (IS_GEN_I(hpriv)) { + /* 50xx: no NCQ, only one command active at a time */ tag = ap->link.active_tag; - - /* Gen II/IIE: get active ATA command via tag, to enable - * support for queueing. this works transparently for - * queued and non-queued modes. - */ - else - tag = le16_to_cpu(pp->crpb[out_index].id) & 0x1f; - - qc = ata_qc_from_tag(ap, tag); - - /* For non-NCQ mode, the lower 8 bits of status - * are from EDMA_ERR_IRQ_CAUSE_OFS, - * which should be zero if all went well. - */ - status = le16_to_cpu(pp->crpb[out_index].flags); - if ((status & 0xff) && !(pp->pp_flags & MV_PP_FLAG_NCQ_EN)) { - mv_err_intr(ap, qc); - return; - } - - /* and finally, complete the ATA command */ - if (qc) { - qc->err_mask |= - ac_err_mask(status >> CRPB_FLAG_STATUS_SHIFT); - ata_qc_complete(qc); + } else { + /* Gen II/IIE: get command tag from CRPB entry */ + tag = le16_to_cpu(response->id) & 0x1f; } - - /* advance software response queue pointer, to - * indicate (after the loop completes) to hardware - * that we have consumed a response queue entry. - */ + mv_process_crpb_response(ap, response, tag, ncq_enabled); work_done = true; - pp->resp_idx++; } /* Update the software queue position index in hardware */ if (work_done) writelfl((pp->crpb_dma & EDMA_RSP_Q_BASE_LO_MASK) | - (out_index << EDMA_RSP_Q_PTR_SHIFT), - port_mmio + EDMA_RSP_Q_OUT_PTR_OFS); + (pp->resp_idx << EDMA_RSP_Q_PTR_SHIFT), + port_mmio + EDMA_RSP_Q_OUT_PTR); +} + +static void mv_port_intr(struct ata_port *ap, u32 port_cause) +{ + struct mv_port_priv *pp; + int edma_was_enabled; + + if (ap->flags & ATA_FLAG_DISABLED) { + mv_unexpected_intr(ap, 0); + return; + } + /* + * Grab a snapshot of the EDMA_EN flag setting, + * so that we have a consistent view for this port, + * even if something we call of our routines changes it. + */ + pp = ap->private_data; + edma_was_enabled = (pp->pp_flags & MV_PP_FLAG_EDMA_EN); + /* + * Process completed CRPB response(s) before other events. + */ + if (edma_was_enabled && (port_cause & DONE_IRQ)) { + mv_process_crpb_entries(ap, pp); + if (pp->pp_flags & MV_PP_FLAG_DELAYED_EH) + mv_handle_fbs_ncq_dev_err(ap); + } + /* + * Handle chip-reported errors, or continue on to handle PIO. + */ + if (unlikely(port_cause & ERR_IRQ)) { + mv_err_intr(ap); + } else if (!edma_was_enabled) { + struct ata_queued_cmd *qc = mv_get_active_qc(ap); + if (qc) + ata_sff_host_intr(ap, qc); + else + mv_unexpected_intr(ap, edma_was_enabled); + } } /** * mv_host_intr - Handle all interrupts on the given host controller * @host: host specific structure - * @relevant: port error bits relevant to this host controller - * @hc: which host controller we're to look at - * - * Read then write clear the HC interrupt status then walk each - * port connected to the HC and see if it needs servicing. Port - * success ints are reported in the HC interrupt status reg, the - * port error ints are reported in the higher level main - * interrupt status register and thus are passed in via the - * 'relevant' argument. + * @main_irq_cause: Main interrupt cause register for the chip. * * LOCKING: * Inherited from caller. */ -static void mv_host_intr(struct ata_host *host, u32 relevant, unsigned int hc) +static int mv_host_intr(struct ata_host *host, u32 main_irq_cause) { struct mv_host_priv *hpriv = host->private_data; - void __iomem *mmio = hpriv->base; - void __iomem *hc_mmio = mv_hc_base(mmio, hc); - u32 hc_irq_cause; - int port, port0, last_port; - - if (hc == 0) - port0 = 0; - else - port0 = MV_PORTS_PER_HC; - - if (HAS_PCI(host)) - last_port = port0 + MV_PORTS_PER_HC; - else - last_port = port0 + hpriv->n_ports; - /* we'll need the HC success int register in most cases */ - hc_irq_cause = readl(hc_mmio + HC_IRQ_CAUSE_OFS); - if (!hc_irq_cause) - return; - - writelfl(~hc_irq_cause, hc_mmio + HC_IRQ_CAUSE_OFS); + void __iomem *mmio = hpriv->base, *hc_mmio; + unsigned int handled = 0, port; - VPRINTK("ENTER, hc%u relevant=0x%08x HC IRQ cause=0x%08x\n", - hc, relevant, hc_irq_cause); + /* If asserted, clear the "all ports" IRQ coalescing bit */ + if (main_irq_cause & ALL_PORTS_COAL_DONE) + writel(~ALL_PORTS_COAL_IRQ, mmio + IRQ_COAL_CAUSE); - for (port = port0; port < last_port; port++) { + for (port = 0; port < hpriv->n_ports; port++) { struct ata_port *ap = host->ports[port]; - struct mv_port_priv *pp; - int have_err_bits, hardport, shift; - - if ((!ap) || (ap->flags & ATA_FLAG_DISABLED)) - continue; - - pp = ap->private_data; + unsigned int p, shift, hardport, port_cause; - shift = port << 1; /* (port * 2) */ - if (port >= MV_PORTS_PER_HC) - shift++; /* skip bit 8 in the HC Main IRQ reg */ - - have_err_bits = ((ERR_IRQ << shift) & relevant); - - if (unlikely(have_err_bits)) { - struct ata_queued_cmd *qc; - - qc = ata_qc_from_tag(ap, ap->link.active_tag); - if (qc && (qc->tf.flags & ATA_TFLAG_POLLING)) + MV_PORT_TO_SHIFT_AND_HARDPORT(port, shift, hardport); + /* + * Each hc within the host has its own hc_irq_cause register, + * where the interrupting ports bits get ack'd. + */ + if (hardport == 0) { /* first port on this hc ? */ + u32 hc_cause = (main_irq_cause >> shift) & HC0_IRQ_PEND; + u32 port_mask, ack_irqs; + /* + * Skip this entire hc if nothing pending for any ports + */ + if (!hc_cause) { + port += MV_PORTS_PER_HC - 1; continue; - - mv_err_intr(ap, qc); - continue; - } - - hardport = mv_hardport_from_port(port); /* range 0..3 */ - - if (pp->pp_flags & MV_PP_FLAG_EDMA_EN) { - if ((DMA_IRQ << hardport) & hc_irq_cause) - mv_intr_edma(ap); - } else { - if ((DEV_IRQ << hardport) & hc_irq_cause) - mv_intr_pio(ap); + } + /* + * We don't need/want to read the hc_irq_cause register, + * because doing so hurts performance, and + * main_irq_cause already gives us everything we need. + * + * But we do have to *write* to the hc_irq_cause to ack + * the ports that we are handling this time through. + * + * This requires that we create a bitmap for those + * ports which interrupted us, and use that bitmap + * to ack (only) those ports via hc_irq_cause. + */ + ack_irqs = 0; + if (hc_cause & PORTS_0_3_COAL_DONE) + ack_irqs = HC_COAL_IRQ; + for (p = 0; p < MV_PORTS_PER_HC; ++p) { + if ((port + p) >= hpriv->n_ports) + break; + port_mask = (DONE_IRQ | ERR_IRQ) << (p * 2); + if (hc_cause & port_mask) + ack_irqs |= (DMA_IRQ | DEV_IRQ) << p; + } + hc_mmio = mv_hc_base_from_port(mmio, port); + writelfl(~ack_irqs, hc_mmio + HC_IRQ_CAUSE); + handled = 1; } + /* + * Handle interrupts signalled for this port: + */ + port_cause = (main_irq_cause >> shift) & (DONE_IRQ | ERR_IRQ); + if (port_cause) + mv_port_intr(ap, port_cause); } - VPRINTK("EXIT\n"); + return handled; } -static void mv_pci_error(struct ata_host *host, void __iomem *mmio) +static int mv_pci_error(struct ata_host *host, void __iomem *mmio) { struct mv_host_priv *hpriv = host->private_data; struct ata_port *ap; @@ -1748,7 +2897,7 @@ static void mv_pci_error(struct ata_host *host, void __iomem *mmio) unsigned int i, err_mask, printed = 0; u32 err_cause; - err_cause = readl(mmio + hpriv->irq_cause_ofs); + err_cause = readl(mmio + hpriv->irq_cause_offset); dev_printk(KERN_ERR, host->dev, "PCI ERROR; PCI IRQ cause=0x%08x\n", err_cause); @@ -1756,7 +2905,7 @@ static void mv_pci_error(struct ata_host *host, void __iomem *mmio) DPRINTK("All regs @ PCI error\n"); mv_dump_all_regs(mmio, -1, to_pci_dev(host->dev)); - writelfl(0, mmio + hpriv->irq_cause_ofs); + writelfl(0, mmio + hpriv->irq_cause_offset); for (i = 0; i < host->n_ports; i++) { ap = host->ports[i]; @@ -1777,6 +2926,7 @@ static void mv_pci_error(struct ata_host *host, void __iomem *mmio) ata_port_freeze(ap); } } + return 1; /* handled */ } /** @@ -1797,38 +2947,35 @@ static irqreturn_t mv_interrupt(int irq, void *dev_instance) { struct ata_host *host = dev_instance; struct mv_host_priv *hpriv = host->private_data; - unsigned int hc, handled = 0, n_hcs; - void __iomem *mmio = hpriv->base; - u32 main_cause, main_mask; + unsigned int handled = 0; + int using_msi = hpriv->hp_flags & MV_HP_FLAG_MSI; + u32 main_irq_cause, pending_irqs; spin_lock(&host->lock); - main_cause = readl(hpriv->main_cause_reg_addr); - main_mask = readl(hpriv->main_mask_reg_addr); + + /* for MSI: block new interrupts while in here */ + if (using_msi) + mv_write_main_irq_mask(0, hpriv); + + main_irq_cause = readl(hpriv->main_irq_cause_addr); + pending_irqs = main_irq_cause & hpriv->main_irq_mask; /* * Deal with cases where we either have nothing pending, or have read * a bogus register value which can indicate HW removal or PCI fault. */ - if (!(main_cause & main_mask) || (main_cause == 0xffffffffU)) - goto out_unlock; - - n_hcs = mv_get_hc_count(host->ports[0]->flags); - - if (unlikely((main_cause & PCI_ERR) && HAS_PCI(host))) { - mv_pci_error(host, mmio); - handled = 1; - goto out_unlock; /* skip all other HC irq handling */ + if (pending_irqs && main_irq_cause != 0xffffffffU) { + if (unlikely((pending_irqs & PCI_ERR) && !IS_SOC(hpriv))) + handled = mv_pci_error(host, hpriv->base); + else + handled = mv_host_intr(host, pending_irqs); } - for (hc = 0; hc < n_hcs; hc++) { - u32 relevant = main_cause & (HC0_IRQ_PEND << (hc * HC_SHIFT)); - if (relevant) { - mv_host_intr(host, relevant, hc); - handled = 1; - } - } + /* for MSI: unmask; interrupt cause bits will retrigger now */ + if (using_msi) + mv_write_main_irq_mask(hpriv->main_irq_mask, hpriv); -out_unlock: spin_unlock(&host->lock); + return IRQ_RETVAL(handled); } @@ -1849,11 +2996,11 @@ static unsigned int mv5_scr_offset(unsigned int sc_reg_in) return ofs; } -static int mv5_scr_read(struct ata_port *ap, unsigned int sc_reg_in, u32 *val) +static int mv5_scr_read(struct ata_link *link, unsigned int sc_reg_in, u32 *val) { - struct mv_host_priv *hpriv = ap->host->private_data; + struct mv_host_priv *hpriv = link->ap->host->private_data; void __iomem *mmio = hpriv->base; - void __iomem *addr = mv5_phy_base(mmio, ap->port_no); + void __iomem *addr = mv5_phy_base(mmio, link->ap->port_no); unsigned int ofs = mv5_scr_offset(sc_reg_in); if (ofs != 0xffffffffU) { @@ -1863,11 +3010,11 @@ static int mv5_scr_read(struct ata_port *ap, unsigned int sc_reg_in, u32 *val) return -EINVAL; } -static int mv5_scr_write(struct ata_port *ap, unsigned int sc_reg_in, u32 val) +static int mv5_scr_write(struct ata_link *link, unsigned int sc_reg_in, u32 val) { - struct mv_host_priv *hpriv = ap->host->private_data; + struct mv_host_priv *hpriv = link->ap->host->private_data; void __iomem *mmio = hpriv->base; - void __iomem *addr = mv5_phy_base(mmio, ap->port_no); + void __iomem *addr = mv5_phy_base(mmio, link->ap->port_no); unsigned int ofs = mv5_scr_offset(sc_reg_in); if (ofs != 0xffffffffU) { @@ -1895,7 +3042,7 @@ static void mv5_reset_bus(struct ata_host *host, void __iomem *mmio) static void mv5_reset_flash(struct mv_host_priv *hpriv, void __iomem *mmio) { - writel(0x0fcfffff, mmio + MV_FLASH_CTL); + writel(0x0fcfffff, mmio + FLASH_CTL); } static void mv5_read_preamp(struct mv_host_priv *hpriv, int idx, @@ -1914,7 +3061,7 @@ static void mv5_enable_leds(struct mv_host_priv *hpriv, void __iomem *mmio) { u32 tmp; - writel(0, mmio + MV_GPIO_PORT_CTL); + writel(0, mmio + GPIO_PORT_CTL); /* FIXME: handle MV_HP_ERRATA_50XXB2 errata */ @@ -1932,9 +3079,9 @@ static void mv5_phy_errata(struct mv_host_priv *hpriv, void __iomem *mmio, int fix_apm_sq = (hpriv->hp_flags & MV_HP_ERRATA_50XXB0); if (fix_apm_sq) { - tmp = readl(phy_mmio + MV5_LT_MODE); + tmp = readl(phy_mmio + MV5_LTMODE); tmp |= (1 << 19); - writel(tmp, phy_mmio + MV5_LT_MODE); + writel(tmp, phy_mmio + MV5_LTMODE); tmp = readl(phy_mmio + MV5_PHY_CTL); tmp &= ~0x3; @@ -1957,15 +3104,10 @@ static void mv5_reset_hc_port(struct mv_host_priv *hpriv, void __iomem *mmio, { void __iomem *port_mmio = mv_port_base(mmio, port); - /* - * The datasheet warns against setting ATA_RST when EDMA is active - * (but doesn't say what the problem might be). So we first try - * to disable the EDMA engine before doing the ATA_RST operation. - */ mv_reset_channel(hpriv, mmio, port); ZERO(0x028); /* command */ - writel(0x11f, port_mmio + EDMA_CFG_OFS); + writel(0x11f, port_mmio + EDMA_CFG); ZERO(0x004); /* timer */ ZERO(0x008); /* irq err cause */ ZERO(0x00c); /* irq err mask */ @@ -2029,10 +3171,9 @@ static void mv_reset_pci_bus(struct ata_host *host, void __iomem *mmio) ZERO(MV_PCI_DISC_TIMER); ZERO(MV_PCI_MSI_TRIGGER); writel(0x000100ff, mmio + MV_PCI_XBAR_TMOUT); - ZERO(HC_MAIN_IRQ_MASK_OFS); ZERO(MV_PCI_SERR_MASK); - ZERO(hpriv->irq_cause_ofs); - ZERO(hpriv->irq_mask_ofs); + ZERO(hpriv->irq_cause_offset); + ZERO(hpriv->irq_mask_offset); ZERO(MV_PCI_ERR_LOW_ADDRESS); ZERO(MV_PCI_ERR_HIGH_ADDRESS); ZERO(MV_PCI_ERR_ATTRIBUTE); @@ -2046,10 +3187,10 @@ static void mv6_reset_flash(struct mv_host_priv *hpriv, void __iomem *mmio) mv5_reset_flash(hpriv, mmio); - tmp = readl(mmio + MV_GPIO_PORT_CTL); + tmp = readl(mmio + GPIO_PORT_CTL); tmp &= 0x3; tmp |= (1 << 5) | (1 << 6); - writel(tmp, mmio + MV_GPIO_PORT_CTL); + writel(tmp, mmio + GPIO_PORT_CTL); } /** @@ -2064,7 +3205,7 @@ static void mv6_reset_flash(struct mv_host_priv *hpriv, void __iomem *mmio) static int mv6_reset_hc(struct mv_host_priv *hpriv, void __iomem *mmio, unsigned int n_hc) { - void __iomem *reg = mmio + PCI_MAIN_CMD_STS_OFS; + void __iomem *reg = mmio + PCI_MAIN_CMD_STS; int i, rc = 0; u32 t; @@ -2112,13 +3253,6 @@ static int mv6_reset_hc(struct mv_host_priv *hpriv, void __iomem *mmio, printk(KERN_ERR DRV_NAME ": can't clear global reset\n"); rc = 1; } - /* - * Temporary: wait 3 seconds before port-probing can happen, - * so that we don't miss finding sleepy SilXXXX port-multipliers. - * This can go away once hotplug is fully/correctly implemented. - */ - if (rc == 0) - msleep(3000); done: return rc; } @@ -2129,7 +3263,7 @@ static void mv6_read_preamp(struct mv_host_priv *hpriv, int idx, void __iomem *port_mmio; u32 tmp; - tmp = readl(mmio + MV_RESET_CFG); + tmp = readl(mmio + RESET_CFG); if ((tmp & (1 << 0)) == 0) { hpriv->signal[idx].amps = 0x7 << 8; hpriv->signal[idx].pre = 0x1 << 5; @@ -2145,7 +3279,7 @@ static void mv6_read_preamp(struct mv_host_priv *hpriv, int idx, static void mv6_enable_leds(struct mv_host_priv *hpriv, void __iomem *mmio) { - writel(0x00000060, mmio + MV_GPIO_PORT_CTL); + writel(0x00000060, mmio + GPIO_PORT_CTL); } static void mv6_phy_errata(struct mv_host_priv *hpriv, void __iomem *mmio, @@ -2158,7 +3292,7 @@ static void mv6_phy_errata(struct mv_host_priv *hpriv, void __iomem *mmio, hp_flags & (MV_HP_ERRATA_60X1B2 | MV_HP_ERRATA_60X1C0); int fix_phy_mode4 = hp_flags & (MV_HP_ERRATA_60X1B2 | MV_HP_ERRATA_60X1C0); - u32 m2, tmp; + u32 m2, m3; if (fix_phy_mode2) { m2 = readl(port_mmio + PHY_MODE2); @@ -2175,28 +3309,37 @@ static void mv6_phy_errata(struct mv_host_priv *hpriv, void __iomem *mmio, udelay(200); } - /* who knows what this magic does */ - tmp = readl(port_mmio + PHY_MODE3); - tmp &= ~0x7F800000; - tmp |= 0x2A800000; - writel(tmp, port_mmio + PHY_MODE3); - - if (fix_phy_mode4) { - u32 m4; - - m4 = readl(port_mmio + PHY_MODE4); - - if (hp_flags & MV_HP_ERRATA_60X1B2) - tmp = readl(port_mmio + PHY_MODE3); + /* + * Gen-II/IIe PHY_MODE3 errata RM#2: + * Achieves better receiver noise performance than the h/w default: + */ + m3 = readl(port_mmio + PHY_MODE3); + m3 = (m3 & 0x1f) | (0x5555601 << 5); - /* workaround for errata FEr SATA#10 (part 1) */ - m4 = (m4 & ~(1 << 1)) | (1 << 0); + /* Guideline 88F5182 (GL# SATA-S11) */ + if (IS_SOC(hpriv)) + m3 &= ~0x1c; + if (fix_phy_mode4) { + u32 m4 = readl(port_mmio + PHY_MODE4); + /* + * Enforce reserved-bit restrictions on GenIIe devices only. + * For earlier chipsets, force only the internal config field + * (workaround for errata FEr SATA#10 part 1). + */ + if (IS_GEN_IIE(hpriv)) + m4 = (m4 & ~PHY_MODE4_RSVD_ZEROS) | PHY_MODE4_RSVD_ONES; + else + m4 = (m4 & ~PHY_MODE4_CFG_MASK) | PHY_MODE4_CFG_VALUE; writel(m4, port_mmio + PHY_MODE4); - - if (hp_flags & MV_HP_ERRATA_60X1B2) - writel(tmp, port_mmio + PHY_MODE3); } + /* + * Workaround for 60x1-B2 errata SATA#13: + * Any write to PHY_MODE4 (above) may corrupt PHY_MODE3, + * so we must always rewrite PHY_MODE3 after PHY_MODE4. + * Or ensure we use writelfl() when writing PHY_MODE4. + */ + writel(m3, port_mmio + PHY_MODE3); /* Revert values of pre-emphasis and signal amps to the saved ones */ m2 = readl(port_mmio + PHY_MODE2); @@ -2243,15 +3386,10 @@ static void mv_soc_reset_hc_port(struct mv_host_priv *hpriv, { void __iomem *port_mmio = mv_port_base(mmio, port); - /* - * The datasheet warns against setting ATA_RST when EDMA is active - * (but doesn't say what the problem might be). So we first try - * to disable the EDMA engine before doing the ATA_RST operation. - */ mv_reset_channel(hpriv, mmio, port); ZERO(0x028); /* command */ - writel(0x101f, port_mmio + EDMA_CFG_OFS); + writel(0x101f, port_mmio + EDMA_CFG); ZERO(0x004); /* timer */ ZERO(0x008); /* irq err cause */ ZERO(0x00c); /* irq err mask */ @@ -2262,7 +3400,7 @@ static void mv_soc_reset_hc_port(struct mv_host_priv *hpriv, ZERO(0x024); /* respq outp */ ZERO(0x020); /* respq inp */ ZERO(0x02c); /* test control */ - writel(0xbc, port_mmio + EDMA_IORDY_TMOUT); + writel(0x800, port_mmio + EDMA_IORDY_TMOUT); } #undef ZERO @@ -2305,40 +3443,88 @@ static void mv_soc_reset_bus(struct ata_host *host, void __iomem *mmio) return; } -static void mv_setup_ifctl(void __iomem *port_mmio, int want_gen2i) +static void mv_soc_65n_phy_errata(struct mv_host_priv *hpriv, + void __iomem *mmio, unsigned int port) +{ + void __iomem *port_mmio = mv_port_base(mmio, port); + u32 reg; + + reg = readl(port_mmio + PHY_MODE3); + reg &= ~(0x3 << 27); /* SELMUPF (bits 28:27) to 1 */ + reg |= (0x1 << 27); + reg &= ~(0x3 << 29); /* SELMUPI (bits 30:29) to 1 */ + reg |= (0x1 << 29); + writel(reg, port_mmio + PHY_MODE3); + + reg = readl(port_mmio + PHY_MODE4); + reg &= ~0x1; /* SATU_OD8 (bit 0) to 0, reserved bit 16 must be set */ + reg |= (0x1 << 16); + writel(reg, port_mmio + PHY_MODE4); + + reg = readl(port_mmio + PHY_MODE9_GEN2); + reg &= ~0xf; /* TXAMP[3:0] (bits 3:0) to 8 */ + reg |= 0x8; + reg &= ~(0x1 << 14); /* TXAMP[4] (bit 14) to 0 */ + writel(reg, port_mmio + PHY_MODE9_GEN2); + + reg = readl(port_mmio + PHY_MODE9_GEN1); + reg &= ~0xf; /* TXAMP[3:0] (bits 3:0) to 8 */ + reg |= 0x8; + reg &= ~(0x1 << 14); /* TXAMP[4] (bit 14) to 0 */ + writel(reg, port_mmio + PHY_MODE9_GEN1); +} + +/** + * soc_is_65 - check if the soc is 65 nano device + * + * Detect the type of the SoC, this is done by reading the PHYCFG_OFS + * register, this register should contain non-zero value and it exists only + * in the 65 nano devices, when reading it from older devices we get 0. + */ +static bool soc_is_65n(struct mv_host_priv *hpriv) +{ + void __iomem *port0_mmio = mv_port_base(hpriv->base, 0); + + if (readl(port0_mmio + PHYCFG_OFS)) + return true; + return false; +} + +static void mv_setup_ifcfg(void __iomem *port_mmio, int want_gen2i) { - u32 ifctl = readl(port_mmio + SATA_INTERFACE_CFG); + u32 ifcfg = readl(port_mmio + SATA_IFCFG); - ifctl = (ifctl & 0xf7f) | 0x9b1000; /* from chip spec */ + ifcfg = (ifcfg & 0xf7f) | 0x9b1000; /* from chip spec */ if (want_gen2i) - ifctl |= (1 << 7); /* enable gen2i speed */ - writelfl(ifctl, port_mmio + SATA_INTERFACE_CFG); + ifcfg |= (1 << 7); /* enable gen2i speed */ + writelfl(ifcfg, port_mmio + SATA_IFCFG); } -/* - * Caller must ensure that EDMA is not active, - * by first doing mv_stop_edma() where needed. - */ static void mv_reset_channel(struct mv_host_priv *hpriv, void __iomem *mmio, unsigned int port_no) { void __iomem *port_mmio = mv_port_base(mmio, port_no); + /* + * The datasheet warns against setting EDMA_RESET when EDMA is active + * (but doesn't say what the problem might be). So we first try + * to disable the EDMA engine before doing the EDMA_RESET operation. + */ mv_stop_edma_engine(port_mmio); - writelfl(ATA_RST, port_mmio + EDMA_CMD_OFS); + writelfl(EDMA_RESET, port_mmio + EDMA_CMD); if (!IS_GEN_I(hpriv)) { - /* Enable 3.0gb/s link speed */ - mv_setup_ifctl(port_mmio, 1); + /* Enable 3.0gb/s link speed: this survives EDMA_RESET */ + mv_setup_ifcfg(port_mmio, 1); } /* - * Strobing ATA_RST here causes a hard reset of the SATA transport, + * Strobing EDMA_RESET here causes a hard reset of the SATA transport, * link, and physical layers. It resets all SATA interface registers - * (except for SATA_INTERFACE_CFG), and issues a COMRESET to the dev. + * (except for SATA_IFCFG), and issues a COMRESET to the dev. */ - writelfl(ATA_RST, port_mmio + EDMA_CMD_OFS); + writelfl(EDMA_RESET, port_mmio + EDMA_CMD); udelay(25); /* allow reset propagation */ - writelfl(0, port_mmio + EDMA_CMD_OFS); + writelfl(0, port_mmio + EDMA_CMD); hpriv->ops->phy_errata(hpriv, mmio, port_no); @@ -2350,12 +3536,12 @@ static void mv_pmp_select(struct ata_port *ap, int pmp) { if (sata_pmp_supported(ap)) { void __iomem *port_mmio = mv_ap_base(ap); - u32 reg = readl(port_mmio + SATA_IFCTL_OFS); + u32 reg = readl(port_mmio + SATA_IFCTL); int old = reg & 0xf; if (old != pmp) { reg = (reg & ~0xf) | pmp; - writelfl(reg, port_mmio + SATA_IFCTL_OFS); + writelfl(reg, port_mmio + SATA_IFCTL); } } } @@ -2387,6 +3573,8 @@ static int mv_hardreset(struct ata_link *link, unsigned int *class, mv_reset_channel(hpriv, mmio, ap->port_no); pp->pp_flags &= ~MV_PP_FLAG_EDMA_EN; + pp->pp_flags &= + ~(MV_PP_FLAG_FBS_EN | MV_PP_FLAG_NCQ_EN | MV_PP_FLAG_FAKE_ATA_BUSY); /* Workaround for errata FEr SATA#10 (part 2) */ do { @@ -2395,69 +3583,46 @@ static int mv_hardreset(struct ata_link *link, unsigned int *class, rc = sata_link_hardreset(link, timing, deadline + extra, &online, NULL); + rc = online ? -EAGAIN : rc; if (rc) return rc; sata_scr_read(link, SCR_STATUS, &sstatus); if (!IS_GEN_I(hpriv) && ++attempts >= 5 && sstatus == 0x121) { /* Force 1.5gb/s link speed and try again */ - mv_setup_ifctl(mv_ap_base(ap), 0); + mv_setup_ifcfg(mv_ap_base(ap), 0); if (time_after(jiffies + HZ, deadline)) extra = HZ; /* only extend it once, max */ } } while (sstatus != 0x0 && sstatus != 0x113 && sstatus != 0x123); + mv_save_cached_regs(ap); + mv_edma_cfg(ap, 0, 0); return rc; } static void mv_eh_freeze(struct ata_port *ap) { - struct mv_host_priv *hpriv = ap->host->private_data; - unsigned int hc = (ap->port_no > 3) ? 1 : 0; - unsigned int shift; - u32 main_mask; - - /* FIXME: handle coalescing completion events properly */ - - shift = ap->port_no * 2; - if (hc > 0) - shift++; - - /* disable assertion of portN err, done events */ - main_mask = readl(hpriv->main_mask_reg_addr); - main_mask &= ~((DONE_IRQ | ERR_IRQ) << shift); - writelfl(main_mask, hpriv->main_mask_reg_addr); + mv_stop_edma(ap); + mv_enable_port_irqs(ap, 0); } static void mv_eh_thaw(struct ata_port *ap) { struct mv_host_priv *hpriv = ap->host->private_data; - void __iomem *mmio = hpriv->base; - unsigned int hc = (ap->port_no > 3) ? 1 : 0; - void __iomem *hc_mmio = mv_hc_base(mmio, hc); + unsigned int port = ap->port_no; + unsigned int hardport = mv_hardport_from_port(port); + void __iomem *hc_mmio = mv_hc_base_from_port(hpriv->base, port); void __iomem *port_mmio = mv_ap_base(ap); - unsigned int shift, hc_port_no = ap->port_no; - u32 main_mask, hc_irq_cause; - - /* FIXME: handle coalescing completion events properly */ - - shift = ap->port_no * 2; - if (hc > 0) { - shift++; - hc_port_no -= 4; - } + u32 hc_irq_cause; /* clear EDMA errors on this port */ - writel(0, port_mmio + EDMA_ERR_IRQ_CAUSE_OFS); + writel(0, port_mmio + EDMA_ERR_IRQ_CAUSE); /* clear pending irq events */ - hc_irq_cause = readl(hc_mmio + HC_IRQ_CAUSE_OFS); - hc_irq_cause &= ~((DEV_IRQ | DMA_IRQ) << hc_port_no); - writel(hc_irq_cause, hc_mmio + HC_IRQ_CAUSE_OFS); + hc_irq_cause = ~((DEV_IRQ | DMA_IRQ) << hardport); + writelfl(hc_irq_cause, hc_mmio + HC_IRQ_CAUSE); - /* enable assertion of portN err, done events */ - main_mask = readl(hpriv->main_mask_reg_addr); - main_mask |= ((DONE_IRQ | ERR_IRQ) << shift); - writelfl(main_mask, hpriv->main_mask_reg_addr); + mv_enable_port_irqs(ap, ERR_IRQ); } /** @@ -2474,8 +3639,7 @@ static void mv_eh_thaw(struct ata_port *ap) */ static void mv_port_init(struct ata_ioports *port, void __iomem *port_mmio) { - void __iomem *shd_base = port_mmio + SHD_BLK_OFS; - unsigned serr_ofs; + void __iomem *serr, *shd_base = port_mmio + SHD_BLK; /* PIO related setup */ @@ -2490,23 +3654,63 @@ static void mv_port_init(struct ata_ioports *port, void __iomem *port_mmio) port->status_addr = port->command_addr = shd_base + (sizeof(u32) * ATA_REG_STATUS); /* special case: control/altstatus doesn't have ATA_REG_ address */ - port->altstatus_addr = port->ctl_addr = shd_base + SHD_CTL_AST_OFS; + port->altstatus_addr = port->ctl_addr = shd_base + SHD_CTL_AST; /* unused: */ port->cmd_addr = port->bmdma_addr = port->scr_addr = NULL; /* Clear any currently outstanding port interrupt conditions */ - serr_ofs = mv_scr_offset(SCR_ERROR); - writelfl(readl(port_mmio + serr_ofs), port_mmio + serr_ofs); - writelfl(0, port_mmio + EDMA_ERR_IRQ_CAUSE_OFS); + serr = port_mmio + mv_scr_offset(SCR_ERROR); + writelfl(readl(serr), serr); + writelfl(0, port_mmio + EDMA_ERR_IRQ_CAUSE); /* unmask all non-transient EDMA error interrupts */ - writelfl(~EDMA_ERR_IRQ_TRANSIENT, port_mmio + EDMA_ERR_IRQ_MASK_OFS); + writelfl(~EDMA_ERR_IRQ_TRANSIENT, port_mmio + EDMA_ERR_IRQ_MASK); VPRINTK("EDMA cfg=0x%08x EDMA IRQ err cause/mask=0x%08x/0x%08x\n", - readl(port_mmio + EDMA_CFG_OFS), - readl(port_mmio + EDMA_ERR_IRQ_CAUSE_OFS), - readl(port_mmio + EDMA_ERR_IRQ_MASK_OFS)); + readl(port_mmio + EDMA_CFG), + readl(port_mmio + EDMA_ERR_IRQ_CAUSE), + readl(port_mmio + EDMA_ERR_IRQ_MASK)); +} + +static unsigned int mv_in_pcix_mode(struct ata_host *host) +{ + struct mv_host_priv *hpriv = host->private_data; + void __iomem *mmio = hpriv->base; + u32 reg; + + if (IS_SOC(hpriv) || !IS_PCIE(hpriv)) + return 0; /* not PCI-X capable */ + reg = readl(mmio + MV_PCI_MODE); + if ((reg & MV_PCI_MODE_MASK) == 0) + return 0; /* conventional PCI mode */ + return 1; /* chip is in PCI-X mode */ +} + +static int mv_pci_cut_through_okay(struct ata_host *host) +{ + struct mv_host_priv *hpriv = host->private_data; + void __iomem *mmio = hpriv->base; + u32 reg; + + if (!mv_in_pcix_mode(host)) { + reg = readl(mmio + MV_PCI_COMMAND); + if (reg & MV_PCI_COMMAND_MRDTRIG) + return 0; /* not okay */ + } + return 1; /* okay */ +} + +static void mv_60x1b2_errata_pci7(struct ata_host *host) +{ + struct mv_host_priv *hpriv = host->private_data; + void __iomem *mmio = hpriv->base; + + /* workaround for 60x1-B2 errata PCI#7 */ + if (mv_in_pcix_mode(host)) { + u32 reg = readl(mmio + MV_PCI_COMMAND); + writelfl(reg & ~MV_PCI_COMMAND_MWRCOM, mmio + MV_PCI_COMMAND); + } } static int mv_chip_id(struct ata_host *host, unsigned int board_idx) @@ -2562,6 +3766,7 @@ static int mv_chip_id(struct ata_host *host, unsigned int board_idx) switch (pdev->revision) { case 0x7: + mv_60x1b2_errata_pci7(host); hp_flags |= MV_HP_ERRATA_60X1B2; break; case 0x9: @@ -2576,7 +3781,7 @@ static int mv_chip_id(struct ata_host *host, unsigned int board_idx) break; case chip_7042: - hp_flags |= MV_HP_PCIE; + hp_flags |= MV_HP_PCIE | MV_HP_CUT_THROUGH; if (pdev->vendor == PCI_VENDOR_ID_TTI && (pdev->device == 0x2300 || pdev->device == 0x2310)) { @@ -2606,15 +3811,15 @@ static int mv_chip_id(struct ata_host *host, unsigned int board_idx) " and avoid the final two gigabytes on" " all RocketRAID BIOS initialized drives.\n"); } + /* drop through */ case chip_6042: hpriv->ops = &mv6xxx_ops; hp_flags |= MV_HP_GEN_IIE; + if (board_idx == chip_6042 && mv_pci_cut_through_okay(host)) + hp_flags |= MV_HP_CUT_THROUGH; switch (pdev->revision) { - case 0x0: - hp_flags |= MV_HP_ERRATA_XX42A0; - break; - case 0x1: + case 0x2: /* Rev.B0: the first/only public release */ hp_flags |= MV_HP_ERRATA_60X1C0; break; default: @@ -2625,8 +3830,12 @@ static int mv_chip_id(struct ata_host *host, unsigned int board_idx) } break; case chip_soc: - hpriv->ops = &mv_soc_ops; - hp_flags |= MV_HP_ERRATA_60X1C0; + if (soc_is_65n(hpriv)) + hpriv->ops = &mv_soc_65n_ops; + else + hpriv->ops = &mv_soc_ops; + hp_flags |= MV_HP_FLAG_SOC | MV_HP_GEN_IIE | + MV_HP_ERRATA_60X1C0; break; default: @@ -2637,12 +3846,12 @@ static int mv_chip_id(struct ata_host *host, unsigned int board_idx) hpriv->hp_flags = hp_flags; if (hp_flags & MV_HP_PCIE) { - hpriv->irq_cause_ofs = PCIE_IRQ_CAUSE_OFS; - hpriv->irq_mask_ofs = PCIE_IRQ_MASK_OFS; + hpriv->irq_cause_offset = PCIE_IRQ_CAUSE; + hpriv->irq_mask_offset = PCIE_IRQ_MASK; hpriv->unmask_all_irqs = PCIE_UNMASK_ALL_IRQS; } else { - hpriv->irq_cause_ofs = PCI_IRQ_CAUSE_OFS; - hpriv->irq_mask_ofs = PCI_IRQ_MASK_OFS; + hpriv->irq_cause_offset = PCI_IRQ_CAUSE; + hpriv->irq_mask_offset = PCI_IRQ_MASK; hpriv->unmask_all_irqs = PCI_UNMASK_ALL_IRQS; } @@ -2652,7 +3861,6 @@ static int mv_chip_id(struct ata_host *host, unsigned int board_idx) /** * mv_init_host - Perform some early initialization of the host. * @host: ATA host to initialize - * @board_idx: controller index * * If possible, do an early global reset of the host. Then do * our port init and clear/unmask all/relevant host interrupts. @@ -2660,31 +3868,35 @@ static int mv_chip_id(struct ata_host *host, unsigned int board_idx) * LOCKING: * Inherited from caller. */ -static int mv_init_host(struct ata_host *host, unsigned int board_idx) +static int mv_init_host(struct ata_host *host) { int rc = 0, n_hc, port, hc; struct mv_host_priv *hpriv = host->private_data; void __iomem *mmio = hpriv->base; - rc = mv_chip_id(host, board_idx); + rc = mv_chip_id(host, hpriv->board_idx); if (rc) goto done; - if (HAS_PCI(host)) { - hpriv->main_cause_reg_addr = mmio + HC_MAIN_IRQ_CAUSE_OFS; - hpriv->main_mask_reg_addr = mmio + HC_MAIN_IRQ_MASK_OFS; + if (IS_SOC(hpriv)) { + hpriv->main_irq_cause_addr = mmio + SOC_HC_MAIN_IRQ_CAUSE; + hpriv->main_irq_mask_addr = mmio + SOC_HC_MAIN_IRQ_MASK; } else { - hpriv->main_cause_reg_addr = mmio + HC_SOC_MAIN_IRQ_CAUSE_OFS; - hpriv->main_mask_reg_addr = mmio + HC_SOC_MAIN_IRQ_MASK_OFS; + hpriv->main_irq_cause_addr = mmio + PCI_HC_MAIN_IRQ_CAUSE; + hpriv->main_irq_mask_addr = mmio + PCI_HC_MAIN_IRQ_MASK; } + /* initialize shadow irq mask with register's value */ + hpriv->main_irq_mask = readl(hpriv->main_irq_mask_addr); + /* global interrupt mask: 0 == mask everything */ - writel(0, hpriv->main_mask_reg_addr); + mv_set_main_irq_mask(host, ~0, 0); n_hc = mv_get_hc_count(host->ports[0]->flags); for (port = 0; port < host->n_ports; port++) - hpriv->ops->read_preamp(hpriv, port, mmio); + if (hpriv->ops->read_preamp) + hpriv->ops->read_preamp(hpriv, port, mmio); rc = hpriv->ops->reset_hc(hpriv, mmio, n_hc); if (rc) @@ -2699,14 +3911,6 @@ static int mv_init_host(struct ata_host *host, unsigned int board_idx) void __iomem *port_mmio = mv_port_base(mmio, port); mv_port_init(&ap->ioaddr, port_mmio); - -#ifdef CONFIG_PCI - if (HAS_PCI(host)) { - unsigned int offset = port_mmio - mmio; - ata_port_pbar_desc(ap, MV_PRIMARY_BAR, -1, "mmio"); - ata_port_pbar_desc(ap, MV_PRIMARY_BAR, offset, "port"); - } -#endif } for (hc = 0; hc < n_hc; hc++) { @@ -2714,39 +3918,28 @@ static int mv_init_host(struct ata_host *host, unsigned int board_idx) VPRINTK("HC%i: HC config=0x%08x HC IRQ cause " "(before clear)=0x%08x\n", hc, - readl(hc_mmio + HC_CFG_OFS), - readl(hc_mmio + HC_IRQ_CAUSE_OFS)); + readl(hc_mmio + HC_CFG), + readl(hc_mmio + HC_IRQ_CAUSE)); /* Clear any currently outstanding hc interrupt conditions */ - writelfl(0, hc_mmio + HC_IRQ_CAUSE_OFS); + writelfl(0, hc_mmio + HC_IRQ_CAUSE); } - if (HAS_PCI(host)) { + if (!IS_SOC(hpriv)) { /* Clear any currently outstanding host interrupt conditions */ - writelfl(0, mmio + hpriv->irq_cause_ofs); + writelfl(0, mmio + hpriv->irq_cause_offset); /* and unmask interrupt generation for host regs */ - writelfl(hpriv->unmask_all_irqs, mmio + hpriv->irq_mask_ofs); - if (IS_GEN_I(hpriv)) - writelfl(~HC_MAIN_MASKED_IRQS_5, - hpriv->main_mask_reg_addr); - else - writelfl(~HC_MAIN_MASKED_IRQS, - hpriv->main_mask_reg_addr); - - VPRINTK("HC MAIN IRQ cause/mask=0x%08x/0x%08x " - "PCI int cause/mask=0x%08x/0x%08x\n", - readl(hpriv->main_cause_reg_addr), - readl(hpriv->main_mask_reg_addr), - readl(mmio + hpriv->irq_cause_ofs), - readl(mmio + hpriv->irq_mask_ofs)); - } else { - writelfl(~HC_MAIN_MASKED_IRQS_SOC, - hpriv->main_mask_reg_addr); - VPRINTK("HC MAIN IRQ cause/mask=0x%08x/0x%08x\n", - readl(hpriv->main_cause_reg_addr), - readl(hpriv->main_mask_reg_addr)); + writelfl(hpriv->unmask_all_irqs, mmio + hpriv->irq_mask_offset); } + + /* + * enable only global host interrupts for now. + * The per-port interrupts get done later as ports are set up. + */ + mv_set_main_irq_mask(host, 0, PCI_ERR); + mv_set_irq_coalescing(host, irq_coalescing_io_count, + irq_coalescing_usecs); done: return rc; } @@ -2840,11 +4033,20 @@ static int mv_platform_probe(struct platform_device *pdev) return -ENOMEM; host->private_data = hpriv; hpriv->n_ports = n_ports; + hpriv->board_idx = chip_soc; host->iomap = NULL; hpriv->base = devm_ioremap(&pdev->dev, res->start, - res->end - res->start + 1); - hpriv->base -= MV_SATAHC0_REG_BASE; + resource_size(res)); + hpriv->base -= SATAHC0_REG_BASE; + +#if defined(CONFIG_HAVE_CLK) + hpriv->clk = clk_get(&pdev->dev, NULL); + if (IS_ERR(hpriv->clk)) + dev_notice(&pdev->dev, "cannot get clkdev\n"); + else + clk_enable(hpriv->clk); +#endif /* * (Re-)program MBUS remapping windows if we are asked to. @@ -2854,12 +4056,12 @@ static int mv_platform_probe(struct platform_device *pdev) rc = mv_create_dma_pools(hpriv, &pdev->dev); if (rc) - return rc; + goto err; /* initialize adapter */ - rc = mv_init_host(host, chip_soc); + rc = mv_init_host(host); if (rc) - return rc; + goto err; dev_printk(KERN_INFO, &pdev->dev, "slots %u ports %d\n", (unsigned)MV_MAX_Q_DEPTH, @@ -2867,6 +4069,15 @@ static int mv_platform_probe(struct platform_device *pdev) return ata_host_activate(host, platform_get_irq(pdev, 0), mv_interrupt, IRQF_SHARED, &mv6_sht); +err: +#if defined(CONFIG_HAVE_CLK) + if (!IS_ERR(hpriv->clk)) { + clk_disable(hpriv->clk); + clk_put(hpriv->clk); + } +#endif + + return rc; } /* @@ -2881,14 +4092,66 @@ static int __devexit mv_platform_remove(struct platform_device *pdev) { struct device *dev = &pdev->dev; struct ata_host *host = dev_get_drvdata(dev); - +#if defined(CONFIG_HAVE_CLK) + struct mv_host_priv *hpriv = host->private_data; +#endif ata_host_detach(host); + +#if defined(CONFIG_HAVE_CLK) + if (!IS_ERR(hpriv->clk)) { + clk_disable(hpriv->clk); + clk_put(hpriv->clk); + } +#endif + return 0; +} + +#ifdef CONFIG_PM +static int mv_platform_suspend(struct platform_device *pdev, pm_message_t state) +{ + struct ata_host *host = dev_get_drvdata(&pdev->dev); + if (host) + return ata_host_suspend(host, state); + else + return 0; +} + +static int mv_platform_resume(struct platform_device *pdev) +{ + struct ata_host *host = dev_get_drvdata(&pdev->dev); + int ret; + + if (host) { + struct mv_host_priv *hpriv = host->private_data; + const struct mv_sata_platform_data *mv_platform_data = \ + pdev->dev.platform_data; + /* + * (Re-)program MBUS remapping windows if we are asked to. + */ + if (mv_platform_data->dram != NULL) + mv_conf_mbus_windows(hpriv, mv_platform_data->dram); + + /* initialize adapter */ + ret = mv_init_host(host); + if (ret) { + printk(KERN_ERR DRV_NAME ": Error during HW init\n"); + return ret; + } + ata_host_resume(host); + } + return 0; } +#else +#define mv_platform_suspend NULL +#define mv_platform_resume NULL +#endif static struct platform_driver mv_platform_driver = { .probe = mv_platform_probe, .remove = __devexit_p(mv_platform_remove), + .suspend = mv_platform_suspend, + .resume = mv_platform_resume, .driver = { .name = DRV_NAME, .owner = THIS_MODULE, @@ -2899,6 +4162,9 @@ static struct platform_driver mv_platform_driver = { #ifdef CONFIG_PCI static int mv_pci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent); +#ifdef CONFIG_PM +static int mv_pci_device_resume(struct pci_dev *pdev); +#endif static struct pci_driver mv_pci_driver = { @@ -2906,23 +4172,22 @@ static struct pci_driver mv_pci_driver = { .id_table = mv_pci_tbl, .probe = mv_pci_init_one, .remove = ata_pci_remove_one, -}; - -/* - * module options - */ -static int msi; /* Use PCI msi; either zero (off, default) or non-zero */ +#ifdef CONFIG_PM + .suspend = ata_pci_device_suspend, + .resume = mv_pci_device_resume, +#endif +}; /* move to PCI layer or libata core? */ static int pci_go_64(struct pci_dev *pdev) { int rc; - if (!pci_set_dma_mask(pdev, DMA_64BIT_MASK)) { - rc = pci_set_consistent_dma_mask(pdev, DMA_64BIT_MASK); + if (!pci_set_dma_mask(pdev, DMA_BIT_MASK(64))) { + rc = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(64)); if (rc) { - rc = pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK); + rc = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32)); if (rc) { dev_printk(KERN_ERR, &pdev->dev, "64-bit DMA enable failed\n"); @@ -2930,13 +4195,13 @@ static int pci_go_64(struct pci_dev *pdev) } } } else { - rc = pci_set_dma_mask(pdev, DMA_32BIT_MASK); + rc = pci_set_dma_mask(pdev, DMA_BIT_MASK(32)); if (rc) { dev_printk(KERN_ERR, &pdev->dev, "32-bit DMA enable failed\n"); return rc; } - rc = pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK); + rc = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(32)); if (rc) { dev_printk(KERN_ERR, &pdev->dev, "32-bit consistent DMA enable failed\n"); @@ -3005,7 +4270,7 @@ static int mv_pci_init_one(struct pci_dev *pdev, const struct ata_port_info *ppi[] = { &mv_port_info[board_idx], NULL }; struct ata_host *host; struct mv_host_priv *hpriv; - int n_ports, rc; + int n_ports, port, rc; if (!printed_version++) dev_printk(KERN_INFO, &pdev->dev, "version " DRV_VERSION "\n"); @@ -3019,6 +4284,7 @@ static int mv_pci_init_one(struct pci_dev *pdev, return -ENOMEM; host->private_data = hpriv; hpriv->n_ports = n_ports; + hpriv->board_idx = board_idx; /* acquire resources */ rc = pcim_enable_device(pdev); @@ -3041,14 +4307,23 @@ static int mv_pci_init_one(struct pci_dev *pdev, if (rc) return rc; + for (port = 0; port < host->n_ports; port++) { + struct ata_port *ap = host->ports[port]; + void __iomem *port_mmio = mv_port_base(hpriv->base, port); + unsigned int offset = port_mmio - hpriv->base; + + ata_port_pbar_desc(ap, MV_PRIMARY_BAR, -1, "mmio"); + ata_port_pbar_desc(ap, MV_PRIMARY_BAR, offset, "port"); + } + /* initialize adapter */ - rc = mv_init_host(host, board_idx); + rc = mv_init_host(host); if (rc) return rc; - /* Enable interrupts */ - if (msi && pci_enable_msi(pdev)) - pci_intx(pdev, 1); + /* Enable message-switched interrupts, if requested */ + if (msi && pci_enable_msi(pdev) == 0) + hpriv->hp_flags |= MV_HP_FLAG_MSI; mv_dump_pci_cfg(pdev, 0x68); mv_print_info(host); @@ -3058,6 +4333,27 @@ static int mv_pci_init_one(struct pci_dev *pdev, return ata_host_activate(host, pdev->irq, mv_interrupt, IRQF_SHARED, IS_GEN_I(hpriv) ? &mv5_sht : &mv6_sht); } + +#ifdef CONFIG_PM +static int mv_pci_device_resume(struct pci_dev *pdev) +{ + struct ata_host *host = dev_get_drvdata(&pdev->dev); + int rc; + + rc = ata_pci_device_do_resume(pdev); + if (rc) + return rc; + + /* initialize adapter */ + rc = mv_init_host(host); + if (rc) + return rc; + + ata_host_resume(host); + + return 0; +} +#endif #endif static int mv_platform_probe(struct platform_device *pdev); @@ -3095,10 +4391,5 @@ MODULE_DEVICE_TABLE(pci, mv_pci_tbl); MODULE_VERSION(DRV_VERSION); MODULE_ALIAS("platform:" DRV_NAME); -#ifdef CONFIG_PCI -module_param(msi, int, 0444); -MODULE_PARM_DESC(msi, "Enable use of PCI MSI (0=off, 1=on)"); -#endif - module_init(mv_init); module_exit(mv_exit);