X-Git-Url: http://ftp.safe.ca/?a=blobdiff_plain;f=arch%2Fpowerpc%2Fkernel%2Fhead_64.S;h=844a44b6447254889a10c35c2acf877981a4f16e;hb=HEAD;hp=b7d140430a41e4a4fc625161ad417211984a5570;hpb=f39224a8c1828bdd327539da72a53d8a13595838;p=safe%2Fjmp%2Flinux-2.6 diff --git a/arch/powerpc/kernel/head_64.S b/arch/powerpc/kernel/head_64.S index b7d1404..844a44b 100644 --- a/arch/powerpc/kernel/head_64.S +++ b/arch/powerpc/kernel/head_64.S @@ -12,8 +12,9 @@ * Adapted for 64bit PowerPC by Dave Engebretsen, Peter Bergner, and * Mike Corrigan {engebret|bergner|mikejc}@us.ibm.com * - * This file contains the low-level support and setup for the - * PowerPC-64 platform, including trap and interrupt dispatch. + * This file contains the entry point for the 64-bit kernel along + * with some early initialization code common to all 64-bit powerpc + * variants. * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License @@ -21,7 +22,6 @@ * 2 of the License, or (at your option) any later version. */ -#include #include #include #include @@ -34,86 +34,49 @@ #include #include #include +#include +#include +#include +#include -#ifdef CONFIG_PPC_ISERIES -#define DO_SOFT_DISABLE -#endif - -/* - * We layout physical memory as follows: - * 0x0000 - 0x00ff : Secondary processor spin code - * 0x0100 - 0x2fff : pSeries Interrupt prologs - * 0x3000 - 0x5fff : interrupt support, iSeries and common interrupt prologs - * 0x6000 - 0x6fff : Initial (CPU0) segment table - * 0x7000 - 0x7fff : FWNMI data area - * 0x8000 - : Early init and support code - */ - -/* - * SPRG Usage - * - * Register Definition - * - * SPRG0 reserved for hypervisor - * SPRG1 temp - used to save gpr - * SPRG2 temp - used to save gpr - * SPRG3 virt addr of paca +/* The physical memory is layed out such that the secondary processor + * spin code sits at 0x0000...0x00ff. On server, the vectors follow + * using the layout described in exceptions-64s.S */ /* * Entering into this code we make the following assumptions: - * For pSeries: + * + * For pSeries or server processors: * 1. The MMU is off & open firmware is running in real mode. * 2. The kernel is entered at __start * * For iSeries: * 1. The MMU is on (as it always is for iSeries) * 2. The kernel is entered at system_reset_iSeries + * + * For Book3E processors: + * 1. The MMU is on running in AS0 in a state defined in ePAPR + * 2. The kernel is entered at __start */ .text .globl _stext _stext: -#ifdef CONFIG_PPC_MULTIPLATFORM _GLOBAL(__start) /* NOP this out unconditionally */ BEGIN_FTR_SECTION b .__start_initialization_multiplatform END_FTR_SECTION(0, 1) -#endif /* CONFIG_PPC_MULTIPLATFORM */ /* Catch branch to 0 in real mode */ trap -#ifdef CONFIG_PPC_ISERIES - /* - * At offset 0x20, there is a pointer to iSeries LPAR data. - * This is required by the hypervisor - */ - . = 0x20 - .llong hvReleaseData-KERNELBASE - - /* - * At offset 0x28 and 0x30 are offsets to the mschunks_map - * array (used by the iSeries LPAR debugger to do translation - * between physical addresses and absolute addresses) and - * to the pidhash table (also used by the debugger) + /* Secondary processors spin on this value until it becomes nonzero. + * When it does it contains the real address of the descriptor + * of the function that the cpu should jump to to continue + * initialization. */ - .llong mschunks_map-KERNELBASE - .llong 0 /* pidhash-KERNELBASE SFRXXX */ - - /* Offset 0x38 - Pointer to start of embedded System.map */ - .globl embedded_sysmap_start -embedded_sysmap_start: - .llong 0 - /* Offset 0x40 - Pointer to end of embedded System.map */ - .globl embedded_sysmap_end -embedded_sysmap_end: - .llong 0 - -#endif /* CONFIG_PPC_ISERIES */ - - /* Secondary processors spin on this value until it goes to 1. */ .globl __secondary_hold_spinloop __secondary_hold_spinloop: .llong 0x0 @@ -124,37 +87,65 @@ __secondary_hold_spinloop: __secondary_hold_acknowledge: .llong 0x0 +#ifdef CONFIG_PPC_ISERIES + /* + * At offset 0x20, there is a pointer to iSeries LPAR data. + * This is required by the hypervisor + */ + . = 0x20 + .llong hvReleaseData-KERNELBASE +#endif /* CONFIG_PPC_ISERIES */ + +#ifdef CONFIG_CRASH_DUMP + /* This flag is set to 1 by a loader if the kernel should run + * at the loaded address instead of the linked address. This + * is used by kexec-tools to keep the the kdump kernel in the + * crash_kernel region. The loader is responsible for + * observing the alignment requirement. + */ + /* Do not move this variable as kexec-tools knows about it. */ + . = 0x5c + .globl __run_at_load +__run_at_load: + .long 0x72756e30 /* "run0" -- relocate to 0 by default */ +#endif + . = 0x60 /* - * The following code is used on pSeries to hold secondary processors - * in a spin loop after they have been freed from OpenFirmware, but + * The following code is used to hold secondary processors + * in a spin loop after they have entered the kernel, but * before the bulk of the kernel has been relocated. This code * is relocated to physical address 0x60 before prom_init is run. * All of it must fit below the first exception vector at 0x100. + * Use .globl here not _GLOBAL because we want __secondary_hold + * to be the actual text address, not a descriptor. */ -_GLOBAL(__secondary_hold) + .globl __secondary_hold +__secondary_hold: +#ifndef CONFIG_PPC_BOOK3E mfmsr r24 ori r24,r24,MSR_RI mtmsrd r24 /* RI on */ - +#endif /* Grab our physical cpu number */ mr r24,r3 /* Tell the master cpu we're here */ /* Relocation is off & we are located at an address less */ /* than 0x100, so only need to grab low order offset. */ - std r24,__secondary_hold_acknowledge@l(0) + std r24,__secondary_hold_acknowledge-_stext(0) sync /* All secondary cpus wait here until told to start. */ -100: ld r4,__secondary_hold_spinloop@l(0) - cmpdi 0,r4,1 - bne 100b +100: ld r4,__secondary_hold_spinloop-_stext(0) + cmpdi 0,r4,0 + beq 100b #if defined(CONFIG_SMP) || defined(CONFIG_KEXEC) - LOAD_REG_IMMEDIATE(r4, .pSeries_secondary_smp_init) + ld r4,0(r4) /* deref function descriptor */ mtctr r4 mr r3,r24 + li r4,0 bctr #else BUG_OPCODE @@ -167,1301 +158,69 @@ exception_marker: .text /* - * The following macros define the code that appears as - * the prologue to each of the exception handlers. They - * are split into two parts to allow a single kernel binary - * to be used for pSeries and iSeries. - * LOL. One day... - paulus - */ - -/* - * We make as much of the exception code common between native - * exception handlers (including pSeries LPAR) and iSeries LPAR - * implementations as possible. - */ - -/* - * This is the start of the interrupt handlers for pSeries - * This code runs with relocation off. - */ -#define EX_R9 0 -#define EX_R10 8 -#define EX_R11 16 -#define EX_R12 24 -#define EX_R13 32 -#define EX_SRR0 40 -#define EX_DAR 48 -#define EX_DSISR 56 -#define EX_CCR 60 -#define EX_R3 64 -#define EX_LR 72 - -/* - * We're short on space and time in the exception prolog, so we can't - * use the normal SET_REG_IMMEDIATE macro. Normally we just need the - * low halfword of the address, but for Kdump we need the whole low - * word. - */ -#ifdef CONFIG_CRASH_DUMP -#define LOAD_HANDLER(reg, label) \ - oris reg,reg,(label)@h; /* virt addr of handler ... */ \ - ori reg,reg,(label)@l; /* .. and the rest */ -#else -#define LOAD_HANDLER(reg, label) \ - ori reg,reg,(label)@l; /* virt addr of handler ... */ -#endif - -#define EXCEPTION_PROLOG_PSERIES(area, label) \ - mfspr r13,SPRN_SPRG3; /* get paca address into r13 */ \ - std r9,area+EX_R9(r13); /* save r9 - r12 */ \ - std r10,area+EX_R10(r13); \ - std r11,area+EX_R11(r13); \ - std r12,area+EX_R12(r13); \ - mfspr r9,SPRN_SPRG1; \ - std r9,area+EX_R13(r13); \ - mfcr r9; \ - clrrdi r12,r13,32; /* get high part of &label */ \ - mfmsr r10; \ - mfspr r11,SPRN_SRR0; /* save SRR0 */ \ - LOAD_HANDLER(r12,label) \ - ori r10,r10,MSR_IR|MSR_DR|MSR_RI; \ - mtspr SPRN_SRR0,r12; \ - mfspr r12,SPRN_SRR1; /* and SRR1 */ \ - mtspr SPRN_SRR1,r10; \ - rfid; \ - b . /* prevent speculative execution */ - -/* - * This is the start of the interrupt handlers for iSeries - * This code runs with relocation on. - */ -#define EXCEPTION_PROLOG_ISERIES_1(area) \ - mfspr r13,SPRN_SPRG3; /* get paca address into r13 */ \ - std r9,area+EX_R9(r13); /* save r9 - r12 */ \ - std r10,area+EX_R10(r13); \ - std r11,area+EX_R11(r13); \ - std r12,area+EX_R12(r13); \ - mfspr r9,SPRN_SPRG1; \ - std r9,area+EX_R13(r13); \ - mfcr r9 - -#define EXCEPTION_PROLOG_ISERIES_2 \ - mfmsr r10; \ - ld r12,PACALPPACAPTR(r13); \ - ld r11,LPPACASRR0(r12); \ - ld r12,LPPACASRR1(r12); \ - ori r10,r10,MSR_RI; \ - mtmsrd r10,1 - -/* - * The common exception prolog is used for all except a few exceptions - * such as a segment miss on a kernel address. We have to be prepared - * to take another exception from the point where we first touch the - * kernel stack onwards. - * - * On entry r13 points to the paca, r9-r13 are saved in the paca, - * r9 contains the saved CR, r11 and r12 contain the saved SRR0 and - * SRR1, and relocation is on. - */ -#define EXCEPTION_PROLOG_COMMON(n, area) \ - andi. r10,r12,MSR_PR; /* See if coming from user */ \ - mr r10,r1; /* Save r1 */ \ - subi r1,r1,INT_FRAME_SIZE; /* alloc frame on kernel stack */ \ - beq- 1f; \ - ld r1,PACAKSAVE(r13); /* kernel stack to use */ \ -1: cmpdi cr1,r1,0; /* check if r1 is in userspace */ \ - bge- cr1,bad_stack; /* abort if it is */ \ - std r9,_CCR(r1); /* save CR in stackframe */ \ - std r11,_NIP(r1); /* save SRR0 in stackframe */ \ - std r12,_MSR(r1); /* save SRR1 in stackframe */ \ - std r10,0(r1); /* make stack chain pointer */ \ - std r0,GPR0(r1); /* save r0 in stackframe */ \ - std r10,GPR1(r1); /* save r1 in stackframe */ \ - ACCOUNT_CPU_USER_ENTRY(r9, r10); \ - std r2,GPR2(r1); /* save r2 in stackframe */ \ - SAVE_4GPRS(3, r1); /* save r3 - r6 in stackframe */ \ - SAVE_2GPRS(7, r1); /* save r7, r8 in stackframe */ \ - ld r9,area+EX_R9(r13); /* move r9, r10 to stackframe */ \ - ld r10,area+EX_R10(r13); \ - std r9,GPR9(r1); \ - std r10,GPR10(r1); \ - ld r9,area+EX_R11(r13); /* move r11 - r13 to stackframe */ \ - ld r10,area+EX_R12(r13); \ - ld r11,area+EX_R13(r13); \ - std r9,GPR11(r1); \ - std r10,GPR12(r1); \ - std r11,GPR13(r1); \ - ld r2,PACATOC(r13); /* get kernel TOC into r2 */ \ - mflr r9; /* save LR in stackframe */ \ - std r9,_LINK(r1); \ - mfctr r10; /* save CTR in stackframe */ \ - std r10,_CTR(r1); \ - mfspr r11,SPRN_XER; /* save XER in stackframe */ \ - std r11,_XER(r1); \ - li r9,(n)+1; \ - std r9,_TRAP(r1); /* set trap number */ \ - li r10,0; \ - ld r11,exception_marker@toc(r2); \ - std r10,RESULT(r1); /* clear regs->result */ \ - std r11,STACK_FRAME_OVERHEAD-16(r1); /* mark the frame */ - -/* - * Exception vectors. + * On server, we include the exception vectors code here as it + * relies on absolute addressing which is only possible within + * this compilation unit */ -#define STD_EXCEPTION_PSERIES(n, label) \ - . = n; \ - .globl label##_pSeries; \ -label##_pSeries: \ - HMT_MEDIUM; \ - mtspr SPRN_SPRG1,r13; /* save r13 */ \ - EXCEPTION_PROLOG_PSERIES(PACA_EXGEN, label##_common) - -#define STD_EXCEPTION_ISERIES(n, label, area) \ - .globl label##_iSeries; \ -label##_iSeries: \ - HMT_MEDIUM; \ - mtspr SPRN_SPRG1,r13; /* save r13 */ \ - EXCEPTION_PROLOG_ISERIES_1(area); \ - EXCEPTION_PROLOG_ISERIES_2; \ - b label##_common - -#define MASKABLE_EXCEPTION_ISERIES(n, label) \ - .globl label##_iSeries; \ -label##_iSeries: \ - HMT_MEDIUM; \ - mtspr SPRN_SPRG1,r13; /* save r13 */ \ - EXCEPTION_PROLOG_ISERIES_1(PACA_EXGEN); \ - lbz r10,PACAPROCENABLED(r13); \ - cmpwi 0,r10,0; \ - beq- label##_iSeries_masked; \ - EXCEPTION_PROLOG_ISERIES_2; \ - b label##_common; \ - -#ifdef DO_SOFT_DISABLE -#define DISABLE_INTS \ - lbz r10,PACAPROCENABLED(r13); \ - li r11,0; \ - std r10,SOFTE(r1); \ - mfmsr r10; \ - stb r11,PACAPROCENABLED(r13); \ - ori r10,r10,MSR_EE; \ - mtmsrd r10,1 - -#define ENABLE_INTS \ - lbz r10,PACAPROCENABLED(r13); \ - mfmsr r11; \ - std r10,SOFTE(r1); \ - ori r11,r11,MSR_EE; \ - mtmsrd r11,1 - -#else /* hard enable/disable interrupts */ -#define DISABLE_INTS - -#define ENABLE_INTS \ - ld r12,_MSR(r1); \ - mfmsr r11; \ - rlwimi r11,r12,0,MSR_EE; \ - mtmsrd r11,1 - +#ifdef CONFIG_PPC_BOOK3S +#include "exceptions-64s.S" #endif -#define STD_EXCEPTION_COMMON(trap, label, hdlr) \ - .align 7; \ - .globl label##_common; \ -label##_common: \ - EXCEPTION_PROLOG_COMMON(trap, PACA_EXGEN); \ - DISABLE_INTS; \ - bl .save_nvgprs; \ - addi r3,r1,STACK_FRAME_OVERHEAD; \ - bl hdlr; \ - b .ret_from_except - -/* - * Like STD_EXCEPTION_COMMON, but for exceptions that can occur - * in the idle task and therefore need the special idle handling. - */ -#define STD_EXCEPTION_COMMON_IDLE(trap, label, hdlr) \ - .align 7; \ - .globl label##_common; \ -label##_common: \ - EXCEPTION_PROLOG_COMMON(trap, PACA_EXGEN); \ - FINISH_NAP; \ - DISABLE_INTS; \ - bl .save_nvgprs; \ - addi r3,r1,STACK_FRAME_OVERHEAD; \ - bl hdlr; \ - b .ret_from_except - -#define STD_EXCEPTION_COMMON_LITE(trap, label, hdlr) \ - .align 7; \ - .globl label##_common; \ -label##_common: \ - EXCEPTION_PROLOG_COMMON(trap, PACA_EXGEN); \ - FINISH_NAP; \ - DISABLE_INTS; \ - bl .ppc64_runlatch_on; \ - addi r3,r1,STACK_FRAME_OVERHEAD; \ - bl hdlr; \ - b .ret_from_except_lite +/* KVM trampoline code needs to be close to the interrupt handlers */ -/* - * When the idle code in power4_idle puts the CPU into NAP mode, - * it has to do so in a loop, and relies on the external interrupt - * and decrementer interrupt entry code to get it out of the loop. - * It sets the _TLF_NAPPING bit in current_thread_info()->local_flags - * to signal that it is in the loop and needs help to get out. - */ -#ifdef CONFIG_PPC_970_NAP -#define FINISH_NAP \ -BEGIN_FTR_SECTION \ - clrrdi r11,r1,THREAD_SHIFT; \ - ld r9,TI_LOCAL_FLAGS(r11); \ - andi. r10,r9,_TLF_NAPPING; \ - bnel power4_fixup_nap; \ -END_FTR_SECTION_IFSET(CPU_FTR_CAN_NAP) -#else -#define FINISH_NAP +#ifdef CONFIG_KVM_BOOK3S_64_HANDLER +#include "../kvm/book3s_rmhandlers.S" #endif -/* - * Start of pSeries system interrupt routines - */ - . = 0x100 - .globl __start_interrupts -__start_interrupts: - - STD_EXCEPTION_PSERIES(0x100, system_reset) - - . = 0x200 -_machine_check_pSeries: - HMT_MEDIUM - mtspr SPRN_SPRG1,r13 /* save r13 */ - EXCEPTION_PROLOG_PSERIES(PACA_EXMC, machine_check_common) - - . = 0x300 - .globl data_access_pSeries -data_access_pSeries: - HMT_MEDIUM - mtspr SPRN_SPRG1,r13 -BEGIN_FTR_SECTION - mtspr SPRN_SPRG2,r12 - mfspr r13,SPRN_DAR - mfspr r12,SPRN_DSISR - srdi r13,r13,60 - rlwimi r13,r12,16,0x20 - mfcr r12 - cmpwi r13,0x2c - beq .do_stab_bolted_pSeries - mtcrf 0x80,r12 - mfspr r12,SPRN_SPRG2 -END_FTR_SECTION_IFCLR(CPU_FTR_SLB) - EXCEPTION_PROLOG_PSERIES(PACA_EXGEN, data_access_common) - - . = 0x380 - .globl data_access_slb_pSeries -data_access_slb_pSeries: - HMT_MEDIUM - mtspr SPRN_SPRG1,r13 - mfspr r13,SPRN_SPRG3 /* get paca address into r13 */ - std r3,PACA_EXSLB+EX_R3(r13) - mfspr r3,SPRN_DAR - std r9,PACA_EXSLB+EX_R9(r13) /* save r9 - r12 */ - mfcr r9 -#ifdef __DISABLED__ - /* Keep that around for when we re-implement dynamic VSIDs */ - cmpdi r3,0 - bge slb_miss_user_pseries -#endif /* __DISABLED__ */ - std r10,PACA_EXSLB+EX_R10(r13) - std r11,PACA_EXSLB+EX_R11(r13) - std r12,PACA_EXSLB+EX_R12(r13) - mfspr r10,SPRN_SPRG1 - std r10,PACA_EXSLB+EX_R13(r13) - mfspr r12,SPRN_SRR1 /* and SRR1 */ - b .slb_miss_realmode /* Rel. branch works in real mode */ - - STD_EXCEPTION_PSERIES(0x400, instruction_access) - - . = 0x480 - .globl instruction_access_slb_pSeries -instruction_access_slb_pSeries: - HMT_MEDIUM - mtspr SPRN_SPRG1,r13 - mfspr r13,SPRN_SPRG3 /* get paca address into r13 */ - std r3,PACA_EXSLB+EX_R3(r13) - mfspr r3,SPRN_SRR0 /* SRR0 is faulting address */ - std r9,PACA_EXSLB+EX_R9(r13) /* save r9 - r12 */ - mfcr r9 -#ifdef __DISABLED__ - /* Keep that around for when we re-implement dynamic VSIDs */ - cmpdi r3,0 - bge slb_miss_user_pseries -#endif /* __DISABLED__ */ - std r10,PACA_EXSLB+EX_R10(r13) - std r11,PACA_EXSLB+EX_R11(r13) - std r12,PACA_EXSLB+EX_R12(r13) - mfspr r10,SPRN_SPRG1 - std r10,PACA_EXSLB+EX_R13(r13) - mfspr r12,SPRN_SRR1 /* and SRR1 */ - b .slb_miss_realmode /* Rel. branch works in real mode */ - - STD_EXCEPTION_PSERIES(0x500, hardware_interrupt) - STD_EXCEPTION_PSERIES(0x600, alignment) - STD_EXCEPTION_PSERIES(0x700, program_check) - STD_EXCEPTION_PSERIES(0x800, fp_unavailable) - STD_EXCEPTION_PSERIES(0x900, decrementer) - STD_EXCEPTION_PSERIES(0xa00, trap_0a) - STD_EXCEPTION_PSERIES(0xb00, trap_0b) - - . = 0xc00 - .globl system_call_pSeries -system_call_pSeries: - HMT_MEDIUM - mr r9,r13 - mfmsr r10 - mfspr r13,SPRN_SPRG3 - mfspr r11,SPRN_SRR0 - clrrdi r12,r13,32 - oris r12,r12,system_call_common@h - ori r12,r12,system_call_common@l - mtspr SPRN_SRR0,r12 - ori r10,r10,MSR_IR|MSR_DR|MSR_RI - mfspr r12,SPRN_SRR1 - mtspr SPRN_SRR1,r10 - rfid - b . /* prevent speculative execution */ - - STD_EXCEPTION_PSERIES(0xd00, single_step) - STD_EXCEPTION_PSERIES(0xe00, trap_0e) - - /* We need to deal with the Altivec unavailable exception - * here which is at 0xf20, thus in the middle of the - * prolog code of the PerformanceMonitor one. A little - * trickery is thus necessary - */ - . = 0xf00 - b performance_monitor_pSeries - - STD_EXCEPTION_PSERIES(0xf20, altivec_unavailable) - - STD_EXCEPTION_PSERIES(0x1300, instruction_breakpoint) - STD_EXCEPTION_PSERIES(0x1700, altivec_assist) - - . = 0x3000 - -/*** pSeries interrupt support ***/ - - /* moved from 0xf00 */ - STD_EXCEPTION_PSERIES(., performance_monitor) - - .align 7 -_GLOBAL(do_stab_bolted_pSeries) - mtcrf 0x80,r12 - mfspr r12,SPRN_SPRG2 - EXCEPTION_PROLOG_PSERIES(PACA_EXSLB, .do_stab_bolted) - -/* - * We have some room here we use that to put - * the peries slb miss user trampoline code so it's reasonably - * away from slb_miss_user_common to avoid problems with rfid - * - * This is used for when the SLB miss handler has to go virtual, - * which doesn't happen for now anymore but will once we re-implement - * dynamic VSIDs for shared page tables - */ -#ifdef __DISABLED__ -slb_miss_user_pseries: - std r10,PACA_EXGEN+EX_R10(r13) - std r11,PACA_EXGEN+EX_R11(r13) - std r12,PACA_EXGEN+EX_R12(r13) - mfspr r10,SPRG1 - ld r11,PACA_EXSLB+EX_R9(r13) - ld r12,PACA_EXSLB+EX_R3(r13) - std r10,PACA_EXGEN+EX_R13(r13) - std r11,PACA_EXGEN+EX_R9(r13) - std r12,PACA_EXGEN+EX_R3(r13) - clrrdi r12,r13,32 - mfmsr r10 - mfspr r11,SRR0 /* save SRR0 */ - ori r12,r12,slb_miss_user_common@l /* virt addr of handler */ - ori r10,r10,MSR_IR|MSR_DR|MSR_RI - mtspr SRR0,r12 - mfspr r12,SRR1 /* and SRR1 */ - mtspr SRR1,r10 - rfid - b . /* prevent spec. execution */ -#endif /* __DISABLED__ */ - -/* - * Vectors for the FWNMI option. Share common code. - */ - .globl system_reset_fwnmi - .align 7 -system_reset_fwnmi: - HMT_MEDIUM - mtspr SPRN_SPRG1,r13 /* save r13 */ - EXCEPTION_PROLOG_PSERIES(PACA_EXGEN, system_reset_common) - - .globl machine_check_fwnmi - .align 7 -machine_check_fwnmi: - HMT_MEDIUM - mtspr SPRN_SPRG1,r13 /* save r13 */ - EXCEPTION_PROLOG_PSERIES(PACA_EXMC, machine_check_common) - -#ifdef CONFIG_PPC_ISERIES -/*** ISeries-LPAR interrupt handlers ***/ - - STD_EXCEPTION_ISERIES(0x200, machine_check, PACA_EXMC) - - .globl data_access_iSeries -data_access_iSeries: - mtspr SPRN_SPRG1,r13 -BEGIN_FTR_SECTION - mtspr SPRN_SPRG2,r12 - mfspr r13,SPRN_DAR - mfspr r12,SPRN_DSISR - srdi r13,r13,60 - rlwimi r13,r12,16,0x20 - mfcr r12 - cmpwi r13,0x2c - beq .do_stab_bolted_iSeries - mtcrf 0x80,r12 - mfspr r12,SPRN_SPRG2 -END_FTR_SECTION_IFCLR(CPU_FTR_SLB) - EXCEPTION_PROLOG_ISERIES_1(PACA_EXGEN) - EXCEPTION_PROLOG_ISERIES_2 - b data_access_common - -.do_stab_bolted_iSeries: - mtcrf 0x80,r12 - mfspr r12,SPRN_SPRG2 - EXCEPTION_PROLOG_ISERIES_1(PACA_EXSLB) - EXCEPTION_PROLOG_ISERIES_2 - b .do_stab_bolted - - .globl data_access_slb_iSeries -data_access_slb_iSeries: - mtspr SPRN_SPRG1,r13 /* save r13 */ - mfspr r13,SPRN_SPRG3 /* get paca address into r13 */ - std r3,PACA_EXSLB+EX_R3(r13) - mfspr r3,SPRN_DAR - std r9,PACA_EXSLB+EX_R9(r13) - mfcr r9 -#ifdef __DISABLED__ - cmpdi r3,0 - bge slb_miss_user_iseries -#endif - std r10,PACA_EXSLB+EX_R10(r13) - std r11,PACA_EXSLB+EX_R11(r13) - std r12,PACA_EXSLB+EX_R12(r13) - mfspr r10,SPRN_SPRG1 - std r10,PACA_EXSLB+EX_R13(r13) - ld r12,PACALPPACAPTR(r13) - ld r12,LPPACASRR1(r12) - b .slb_miss_realmode - - STD_EXCEPTION_ISERIES(0x400, instruction_access, PACA_EXGEN) - - .globl instruction_access_slb_iSeries -instruction_access_slb_iSeries: - mtspr SPRN_SPRG1,r13 /* save r13 */ - mfspr r13,SPRN_SPRG3 /* get paca address into r13 */ - std r3,PACA_EXSLB+EX_R3(r13) - ld r3,PACALPPACAPTR(r13) - ld r3,LPPACASRR0(r3) /* get SRR0 value */ - std r9,PACA_EXSLB+EX_R9(r13) - mfcr r9 -#ifdef __DISABLED__ - cmpdi r3,0 - bge .slb_miss_user_iseries -#endif - std r10,PACA_EXSLB+EX_R10(r13) - std r11,PACA_EXSLB+EX_R11(r13) - std r12,PACA_EXSLB+EX_R12(r13) - mfspr r10,SPRN_SPRG1 - std r10,PACA_EXSLB+EX_R13(r13) - ld r12,PACALPPACAPTR(r13) - ld r12,LPPACASRR1(r12) - b .slb_miss_realmode - -#ifdef __DISABLED__ -slb_miss_user_iseries: - std r10,PACA_EXGEN+EX_R10(r13) - std r11,PACA_EXGEN+EX_R11(r13) - std r12,PACA_EXGEN+EX_R12(r13) - mfspr r10,SPRG1 - ld r11,PACA_EXSLB+EX_R9(r13) - ld r12,PACA_EXSLB+EX_R3(r13) - std r10,PACA_EXGEN+EX_R13(r13) - std r11,PACA_EXGEN+EX_R9(r13) - std r12,PACA_EXGEN+EX_R3(r13) - EXCEPTION_PROLOG_ISERIES_2 - b slb_miss_user_common -#endif - - MASKABLE_EXCEPTION_ISERIES(0x500, hardware_interrupt) - STD_EXCEPTION_ISERIES(0x600, alignment, PACA_EXGEN) - STD_EXCEPTION_ISERIES(0x700, program_check, PACA_EXGEN) - STD_EXCEPTION_ISERIES(0x800, fp_unavailable, PACA_EXGEN) - MASKABLE_EXCEPTION_ISERIES(0x900, decrementer) - STD_EXCEPTION_ISERIES(0xa00, trap_0a, PACA_EXGEN) - STD_EXCEPTION_ISERIES(0xb00, trap_0b, PACA_EXGEN) - - .globl system_call_iSeries -system_call_iSeries: - mr r9,r13 - mfspr r13,SPRN_SPRG3 - EXCEPTION_PROLOG_ISERIES_2 - b system_call_common - - STD_EXCEPTION_ISERIES( 0xd00, single_step, PACA_EXGEN) - STD_EXCEPTION_ISERIES( 0xe00, trap_0e, PACA_EXGEN) - STD_EXCEPTION_ISERIES( 0xf00, performance_monitor, PACA_EXGEN) - - .globl system_reset_iSeries -system_reset_iSeries: - mfspr r13,SPRN_SPRG3 /* Get paca address */ - mfmsr r24 - ori r24,r24,MSR_RI - mtmsrd r24 /* RI on */ - lhz r24,PACAPACAINDEX(r13) /* Get processor # */ - cmpwi 0,r24,0 /* Are we processor 0? */ - beq .__start_initialization_iSeries /* Start up the first processor */ - mfspr r4,SPRN_CTRLF - li r5,CTRL_RUNLATCH /* Turn off the run light */ - andc r4,r4,r5 - mtspr SPRN_CTRLT,r4 - -1: - HMT_LOW -#ifdef CONFIG_SMP - lbz r23,PACAPROCSTART(r13) /* Test if this processor - * should start */ - sync - LOAD_REG_IMMEDIATE(r3,current_set) - sldi r28,r24,3 /* get current_set[cpu#] */ - ldx r3,r3,r28 - addi r1,r3,THREAD_SIZE - subi r1,r1,STACK_FRAME_OVERHEAD - - cmpwi 0,r23,0 - beq iSeries_secondary_smp_loop /* Loop until told to go */ - bne .__secondary_start /* Loop until told to go */ -iSeries_secondary_smp_loop: - /* Let the Hypervisor know we are alive */ - /* 8002 is a call to HvCallCfg::getLps, a harmless Hypervisor function */ - lis r3,0x8002 - rldicr r3,r3,32,15 /* r0 = (r3 << 32) & 0xffff000000000000 */ -#else /* CONFIG_SMP */ - /* Yield the processor. This is required for non-SMP kernels - which are running on multi-threaded machines. */ - lis r3,0x8000 - rldicr r3,r3,32,15 /* r3 = (r3 << 32) & 0xffff000000000000 */ - addi r3,r3,18 /* r3 = 0x8000000000000012 which is "yield" */ - li r4,0 /* "yield timed" */ - li r5,-1 /* "yield forever" */ -#endif /* CONFIG_SMP */ - li r0,-1 /* r0=-1 indicates a Hypervisor call */ - sc /* Invoke the hypervisor via a system call */ - mfspr r13,SPRN_SPRG3 /* Put r13 back ???? */ - b 1b /* If SMP not configured, secondaries - * loop forever */ - - .globl decrementer_iSeries_masked -decrementer_iSeries_masked: - /* We may not have a valid TOC pointer in here. */ - li r11,1 - ld r12,PACALPPACAPTR(r13) - stb r11,LPPACADECRINT(r12) - LOAD_REG_IMMEDIATE(r12, tb_ticks_per_jiffy) - lwz r12,0(r12) - mtspr SPRN_DEC,r12 - /* fall through */ - - .globl hardware_interrupt_iSeries_masked -hardware_interrupt_iSeries_masked: - mtcrf 0x80,r9 /* Restore regs */ - ld r12,PACALPPACAPTR(r13) - ld r11,LPPACASRR0(r12) - ld r12,LPPACASRR1(r12) - mtspr SPRN_SRR0,r11 - mtspr SPRN_SRR1,r12 - ld r9,PACA_EXGEN+EX_R9(r13) - ld r10,PACA_EXGEN+EX_R10(r13) - ld r11,PACA_EXGEN+EX_R11(r13) - ld r12,PACA_EXGEN+EX_R12(r13) - ld r13,PACA_EXGEN+EX_R13(r13) - rfid - b . /* prevent speculative execution */ -#endif /* CONFIG_PPC_ISERIES */ - -/*** Common interrupt handlers ***/ - - STD_EXCEPTION_COMMON(0x100, system_reset, .system_reset_exception) - - /* - * Machine check is different because we use a different - * save area: PACA_EXMC instead of PACA_EXGEN. - */ - .align 7 - .globl machine_check_common -machine_check_common: - EXCEPTION_PROLOG_COMMON(0x200, PACA_EXMC) - FINISH_NAP - DISABLE_INTS - bl .save_nvgprs - addi r3,r1,STACK_FRAME_OVERHEAD - bl .machine_check_exception - b .ret_from_except - - STD_EXCEPTION_COMMON_LITE(0x900, decrementer, .timer_interrupt) - STD_EXCEPTION_COMMON(0xa00, trap_0a, .unknown_exception) - STD_EXCEPTION_COMMON(0xb00, trap_0b, .unknown_exception) - STD_EXCEPTION_COMMON(0xd00, single_step, .single_step_exception) - STD_EXCEPTION_COMMON(0xe00, trap_0e, .unknown_exception) - STD_EXCEPTION_COMMON_IDLE(0xf00, performance_monitor, .performance_monitor_exception) - STD_EXCEPTION_COMMON(0x1300, instruction_breakpoint, .instruction_breakpoint_exception) -#ifdef CONFIG_ALTIVEC - STD_EXCEPTION_COMMON(0x1700, altivec_assist, .altivec_assist_exception) -#else - STD_EXCEPTION_COMMON(0x1700, altivec_assist, .unknown_exception) -#endif - -/* - * Here we have detected that the kernel stack pointer is bad. - * R9 contains the saved CR, r13 points to the paca, - * r10 contains the (bad) kernel stack pointer, - * r11 and r12 contain the saved SRR0 and SRR1. - * We switch to using an emergency stack, save the registers there, - * and call kernel_bad_stack(), which panics. - */ -bad_stack: - ld r1,PACAEMERGSP(r13) - subi r1,r1,64+INT_FRAME_SIZE - std r9,_CCR(r1) - std r10,GPR1(r1) - std r11,_NIP(r1) - std r12,_MSR(r1) - mfspr r11,SPRN_DAR - mfspr r12,SPRN_DSISR - std r11,_DAR(r1) - std r12,_DSISR(r1) - mflr r10 - mfctr r11 - mfxer r12 - std r10,_LINK(r1) - std r11,_CTR(r1) - std r12,_XER(r1) - SAVE_GPR(0,r1) - SAVE_GPR(2,r1) - SAVE_4GPRS(3,r1) - SAVE_2GPRS(7,r1) - SAVE_10GPRS(12,r1) - SAVE_10GPRS(22,r1) - addi r11,r1,INT_FRAME_SIZE - std r11,0(r1) - li r12,0 - std r12,0(r11) - ld r2,PACATOC(r13) -1: addi r3,r1,STACK_FRAME_OVERHEAD - bl .kernel_bad_stack - b 1b - -/* - * Return from an exception with minimal checks. - * The caller is assumed to have done EXCEPTION_PROLOG_COMMON. - * If interrupts have been enabled, or anything has been - * done that might have changed the scheduling status of - * any task or sent any task a signal, you should use - * ret_from_except or ret_from_except_lite instead of this. - */ - .globl fast_exception_return -fast_exception_return: - ld r12,_MSR(r1) - ld r11,_NIP(r1) - andi. r3,r12,MSR_RI /* check if RI is set */ - beq- unrecov_fer - -#ifdef CONFIG_VIRT_CPU_ACCOUNTING - andi. r3,r12,MSR_PR - beq 2f - ACCOUNT_CPU_USER_EXIT(r3, r4) -2: -#endif - - ld r3,_CCR(r1) - ld r4,_LINK(r1) - ld r5,_CTR(r1) - ld r6,_XER(r1) - mtcr r3 - mtlr r4 - mtctr r5 - mtxer r6 - REST_GPR(0, r1) - REST_8GPRS(2, r1) - - mfmsr r10 - clrrdi r10,r10,2 /* clear RI (LE is 0 already) */ - mtmsrd r10,1 - - mtspr SPRN_SRR1,r12 - mtspr SPRN_SRR0,r11 - REST_4GPRS(10, r1) - ld r1,GPR1(r1) - rfid - b . /* prevent speculative execution */ - -unrecov_fer: - bl .save_nvgprs -1: addi r3,r1,STACK_FRAME_OVERHEAD - bl .unrecoverable_exception - b 1b - -/* - * Here r13 points to the paca, r9 contains the saved CR, - * SRR0 and SRR1 are saved in r11 and r12, - * r9 - r13 are saved in paca->exgen. - */ - .align 7 - .globl data_access_common -data_access_common: - mfspr r10,SPRN_DAR - std r10,PACA_EXGEN+EX_DAR(r13) - mfspr r10,SPRN_DSISR - stw r10,PACA_EXGEN+EX_DSISR(r13) - EXCEPTION_PROLOG_COMMON(0x300, PACA_EXGEN) - ld r3,PACA_EXGEN+EX_DAR(r13) - lwz r4,PACA_EXGEN+EX_DSISR(r13) - li r5,0x300 - b .do_hash_page /* Try to handle as hpte fault */ - - .align 7 - .globl instruction_access_common -instruction_access_common: - EXCEPTION_PROLOG_COMMON(0x400, PACA_EXGEN) - ld r3,_NIP(r1) - andis. r4,r12,0x5820 - li r5,0x400 - b .do_hash_page /* Try to handle as hpte fault */ - -/* - * Here is the common SLB miss user that is used when going to virtual - * mode for SLB misses, that is currently not used - */ -#ifdef __DISABLED__ - .align 7 - .globl slb_miss_user_common -slb_miss_user_common: - mflr r10 - std r3,PACA_EXGEN+EX_DAR(r13) - stw r9,PACA_EXGEN+EX_CCR(r13) - std r10,PACA_EXGEN+EX_LR(r13) - std r11,PACA_EXGEN+EX_SRR0(r13) - bl .slb_allocate_user - - ld r10,PACA_EXGEN+EX_LR(r13) - ld r3,PACA_EXGEN+EX_R3(r13) - lwz r9,PACA_EXGEN+EX_CCR(r13) - ld r11,PACA_EXGEN+EX_SRR0(r13) - mtlr r10 - beq- slb_miss_fault - - andi. r10,r12,MSR_RI /* check for unrecoverable exception */ - beq- unrecov_user_slb - mfmsr r10 - -.machine push -.machine "power4" - mtcrf 0x80,r9 -.machine pop - - clrrdi r10,r10,2 /* clear RI before setting SRR0/1 */ - mtmsrd r10,1 - - mtspr SRR0,r11 - mtspr SRR1,r12 - - ld r9,PACA_EXGEN+EX_R9(r13) - ld r10,PACA_EXGEN+EX_R10(r13) - ld r11,PACA_EXGEN+EX_R11(r13) - ld r12,PACA_EXGEN+EX_R12(r13) - ld r13,PACA_EXGEN+EX_R13(r13) - rfid - b . - -slb_miss_fault: - EXCEPTION_PROLOG_COMMON(0x380, PACA_EXGEN) - ld r4,PACA_EXGEN+EX_DAR(r13) - li r5,0 - std r4,_DAR(r1) - std r5,_DSISR(r1) - b .handle_page_fault - -unrecov_user_slb: - EXCEPTION_PROLOG_COMMON(0x4200, PACA_EXGEN) - DISABLE_INTS - bl .save_nvgprs -1: addi r3,r1,STACK_FRAME_OVERHEAD - bl .unrecoverable_exception - b 1b - -#endif /* __DISABLED__ */ - - -/* - * r13 points to the PACA, r9 contains the saved CR, - * r12 contain the saved SRR1, SRR0 is still ready for return - * r3 has the faulting address - * r9 - r13 are saved in paca->exslb. - * r3 is saved in paca->slb_r3 - * We assume we aren't going to take any exceptions during this procedure. - */ -_GLOBAL(slb_miss_realmode) - mflr r10 - - stw r9,PACA_EXSLB+EX_CCR(r13) /* save CR in exc. frame */ - std r10,PACA_EXSLB+EX_LR(r13) /* save LR */ - - bl .slb_allocate_realmode - - /* All done -- return from exception. */ - - ld r10,PACA_EXSLB+EX_LR(r13) - ld r3,PACA_EXSLB+EX_R3(r13) - lwz r9,PACA_EXSLB+EX_CCR(r13) /* get saved CR */ -#ifdef CONFIG_PPC_ISERIES - ld r11,PACALPPACAPTR(r13) - ld r11,LPPACASRR0(r11) /* get SRR0 value */ -#endif /* CONFIG_PPC_ISERIES */ - - mtlr r10 - - andi. r10,r12,MSR_RI /* check for unrecoverable exception */ - beq- unrecov_slb - -.machine push -.machine "power4" - mtcrf 0x80,r9 - mtcrf 0x01,r9 /* slb_allocate uses cr0 and cr7 */ -.machine pop - -#ifdef CONFIG_PPC_ISERIES - mtspr SPRN_SRR0,r11 - mtspr SPRN_SRR1,r12 -#endif /* CONFIG_PPC_ISERIES */ - ld r9,PACA_EXSLB+EX_R9(r13) - ld r10,PACA_EXSLB+EX_R10(r13) - ld r11,PACA_EXSLB+EX_R11(r13) - ld r12,PACA_EXSLB+EX_R12(r13) - ld r13,PACA_EXSLB+EX_R13(r13) - rfid - b . /* prevent speculative execution */ - -unrecov_slb: - EXCEPTION_PROLOG_COMMON(0x4100, PACA_EXSLB) - DISABLE_INTS - bl .save_nvgprs -1: addi r3,r1,STACK_FRAME_OVERHEAD - bl .unrecoverable_exception - b 1b - - .align 7 - .globl hardware_interrupt_common - .globl hardware_interrupt_entry -hardware_interrupt_common: - EXCEPTION_PROLOG_COMMON(0x500, PACA_EXGEN) - FINISH_NAP -hardware_interrupt_entry: - DISABLE_INTS - bl .ppc64_runlatch_on - addi r3,r1,STACK_FRAME_OVERHEAD - bl .do_IRQ - b .ret_from_except_lite - -#ifdef CONFIG_PPC_970_NAP -power4_fixup_nap: - andc r9,r9,r10 - std r9,TI_LOCAL_FLAGS(r11) - ld r10,_LINK(r1) /* make idle task do the */ - std r10,_NIP(r1) /* equivalent of a blr */ - blr -#endif - - .align 7 - .globl alignment_common -alignment_common: - mfspr r10,SPRN_DAR - std r10,PACA_EXGEN+EX_DAR(r13) - mfspr r10,SPRN_DSISR - stw r10,PACA_EXGEN+EX_DSISR(r13) - EXCEPTION_PROLOG_COMMON(0x600, PACA_EXGEN) - ld r3,PACA_EXGEN+EX_DAR(r13) - lwz r4,PACA_EXGEN+EX_DSISR(r13) - std r3,_DAR(r1) - std r4,_DSISR(r1) - bl .save_nvgprs - addi r3,r1,STACK_FRAME_OVERHEAD - ENABLE_INTS - bl .alignment_exception - b .ret_from_except - - .align 7 - .globl program_check_common -program_check_common: - EXCEPTION_PROLOG_COMMON(0x700, PACA_EXGEN) - bl .save_nvgprs - addi r3,r1,STACK_FRAME_OVERHEAD - ENABLE_INTS - bl .program_check_exception - b .ret_from_except - - .align 7 - .globl fp_unavailable_common -fp_unavailable_common: - EXCEPTION_PROLOG_COMMON(0x800, PACA_EXGEN) - bne .load_up_fpu /* if from user, just load it up */ - bl .save_nvgprs - addi r3,r1,STACK_FRAME_OVERHEAD - ENABLE_INTS - bl .kernel_fp_unavailable_exception - BUG_OPCODE - - .align 7 - .globl altivec_unavailable_common -altivec_unavailable_common: - EXCEPTION_PROLOG_COMMON(0xf20, PACA_EXGEN) -#ifdef CONFIG_ALTIVEC -BEGIN_FTR_SECTION - bne .load_up_altivec /* if from user, just load it up */ -END_FTR_SECTION_IFSET(CPU_FTR_ALTIVEC) -#endif - bl .save_nvgprs - addi r3,r1,STACK_FRAME_OVERHEAD - ENABLE_INTS - bl .altivec_unavailable_exception - b .ret_from_except - -#ifdef CONFIG_ALTIVEC -/* - * load_up_altivec(unused, unused, tsk) - * Disable VMX for the task which had it previously, - * and save its vector registers in its thread_struct. - * Enables the VMX for use in the kernel on return. - * On SMP we know the VMX is free, since we give it up every - * switch (ie, no lazy save of the vector registers). - * On entry: r13 == 'current' && last_task_used_altivec != 'current' - */ -_STATIC(load_up_altivec) - mfmsr r5 /* grab the current MSR */ - oris r5,r5,MSR_VEC@h - mtmsrd r5 /* enable use of VMX now */ - isync - -/* - * For SMP, we don't do lazy VMX switching because it just gets too - * horrendously complex, especially when a task switches from one CPU - * to another. Instead we call giveup_altvec in switch_to. - * VRSAVE isn't dealt with here, that is done in the normal context - * switch code. Note that we could rely on vrsave value to eventually - * avoid saving all of the VREGs here... - */ -#ifndef CONFIG_SMP - ld r3,last_task_used_altivec@got(r2) - ld r4,0(r3) - cmpdi 0,r4,0 - beq 1f - /* Save VMX state to last_task_used_altivec's THREAD struct */ - addi r4,r4,THREAD - SAVE_32VRS(0,r5,r4) - mfvscr vr0 - li r10,THREAD_VSCR - stvx vr0,r10,r4 - /* Disable VMX for last_task_used_altivec */ - ld r5,PT_REGS(r4) - ld r4,_MSR-STACK_FRAME_OVERHEAD(r5) - lis r6,MSR_VEC@h - andc r4,r4,r6 - std r4,_MSR-STACK_FRAME_OVERHEAD(r5) -1: -#endif /* CONFIG_SMP */ - /* Hack: if we get an altivec unavailable trap with VRSAVE - * set to all zeros, we assume this is a broken application - * that fails to set it properly, and thus we switch it to - * all 1's - */ - mfspr r4,SPRN_VRSAVE - cmpdi 0,r4,0 - bne+ 1f - li r4,-1 - mtspr SPRN_VRSAVE,r4 -1: - /* enable use of VMX after return */ - ld r4,PACACURRENT(r13) - addi r5,r4,THREAD /* Get THREAD */ - oris r12,r12,MSR_VEC@h - std r12,_MSR(r1) - li r4,1 - li r10,THREAD_VSCR - stw r4,THREAD_USED_VR(r5) - lvx vr0,r10,r5 - mtvscr vr0 - REST_32VRS(0,r4,r5) -#ifndef CONFIG_SMP - /* Update last_task_used_math to 'current' */ - subi r4,r5,THREAD /* Back to 'current' */ - std r4,0(r3) -#endif /* CONFIG_SMP */ - /* restore registers and return */ - b fast_exception_return -#endif /* CONFIG_ALTIVEC */ - -/* - * Hash table stuff - */ - .align 7 -_GLOBAL(do_hash_page) - std r3,_DAR(r1) - std r4,_DSISR(r1) - - andis. r0,r4,0xa450 /* weird error? */ - bne- .handle_page_fault /* if not, try to insert a HPTE */ -BEGIN_FTR_SECTION - andis. r0,r4,0x0020 /* Is it a segment table fault? */ - bne- .do_ste_alloc /* If so handle it */ -END_FTR_SECTION_IFCLR(CPU_FTR_SLB) - - /* - * We need to set the _PAGE_USER bit if MSR_PR is set or if we are - * accessing a userspace segment (even from the kernel). We assume - * kernel addresses always have the high bit set. - */ - rlwinm r4,r4,32-25+9,31-9,31-9 /* DSISR_STORE -> _PAGE_RW */ - rotldi r0,r3,15 /* Move high bit into MSR_PR posn */ - orc r0,r12,r0 /* MSR_PR | ~high_bit */ - rlwimi r4,r0,32-13,30,30 /* becomes _PAGE_USER access bit */ - ori r4,r4,1 /* add _PAGE_PRESENT */ - rlwimi r4,r5,22+2,31-2,31-2 /* Set _PAGE_EXEC if trap is 0x400 */ - - /* - * On iSeries, we soft-disable interrupts here, then - * hard-enable interrupts so that the hash_page code can spin on - * the hash_table_lock without problems on a shared processor. - */ - DISABLE_INTS - - /* - * r3 contains the faulting address - * r4 contains the required access permissions - * r5 contains the trap number - * - * at return r3 = 0 for success - */ - bl .hash_page /* build HPTE if possible */ - cmpdi r3,0 /* see if hash_page succeeded */ +_GLOBAL(generic_secondary_thread_init) + mr r24,r3 -#ifdef DO_SOFT_DISABLE - /* - * If we had interrupts soft-enabled at the point where the - * DSI/ISI occurred, and an interrupt came in during hash_page, - * handle it now. - * We jump to ret_from_except_lite rather than fast_exception_return - * because ret_from_except_lite will check for and handle pending - * interrupts if necessary. - */ - beq .ret_from_except_lite - /* For a hash failure, we don't bother re-enabling interrupts */ - ble- 12f + /* turn on 64-bit mode */ + bl .enable_64b_mode - /* - * hash_page couldn't handle it, set soft interrupt enable back - * to what it was before the trap. Note that .local_irq_restore - * handles any interrupts pending at this point. - */ - ld r3,SOFTE(r1) - bl .local_irq_restore - b 11f -#else - beq fast_exception_return /* Return from exception on success */ - ble- 12f /* Failure return from hash_page */ + /* get a valid TOC pointer, wherever we're mapped at */ + bl .relative_toc - /* fall through */ +#ifdef CONFIG_PPC_BOOK3E + /* Book3E initialization */ + mr r3,r24 + bl .book3e_secondary_thread_init #endif - -/* Here we have a page fault that hash_page can't handle. */ -_GLOBAL(handle_page_fault) - ENABLE_INTS -11: ld r4,_DAR(r1) - ld r5,_DSISR(r1) - addi r3,r1,STACK_FRAME_OVERHEAD - bl .do_page_fault - cmpdi r3,0 - beq+ .ret_from_except_lite - bl .save_nvgprs - mr r5,r3 - addi r3,r1,STACK_FRAME_OVERHEAD - lwz r4,_DAR(r1) - bl .bad_page_fault - b .ret_from_except - -/* We have a page fault that hash_page could handle but HV refused - * the PTE insertion - */ -12: bl .save_nvgprs - addi r3,r1,STACK_FRAME_OVERHEAD - lwz r4,_DAR(r1) - bl .low_hash_fault - b .ret_from_except - - /* here we have a segment miss */ -_GLOBAL(do_ste_alloc) - bl .ste_allocate /* try to insert stab entry */ - cmpdi r3,0 - beq+ fast_exception_return - b .handle_page_fault - -/* - * r13 points to the PACA, r9 contains the saved CR, - * r11 and r12 contain the saved SRR0 and SRR1. - * r9 - r13 are saved in paca->exslb. - * We assume we aren't going to take any exceptions during this procedure. - * We assume (DAR >> 60) == 0xc. - */ - .align 7 -_GLOBAL(do_stab_bolted) - stw r9,PACA_EXSLB+EX_CCR(r13) /* save CR in exc. frame */ - std r11,PACA_EXSLB+EX_SRR0(r13) /* save SRR0 in exc. frame */ - - /* Hash to the primary group */ - ld r10,PACASTABVIRT(r13) - mfspr r11,SPRN_DAR - srdi r11,r11,28 - rldimi r10,r11,7,52 /* r10 = first ste of the group */ - - /* Calculate VSID */ - /* This is a kernel address, so protovsid = ESID */ - ASM_VSID_SCRAMBLE(r11, r9) - rldic r9,r11,12,16 /* r9 = vsid << 12 */ - - /* Search the primary group for a free entry */ -1: ld r11,0(r10) /* Test valid bit of the current ste */ - andi. r11,r11,0x80 - beq 2f - addi r10,r10,16 - andi. r11,r10,0x70 - bne 1b - - /* Stick for only searching the primary group for now. */ - /* At least for now, we use a very simple random castout scheme */ - /* Use the TB as a random number ; OR in 1 to avoid entry 0 */ - mftb r11 - rldic r11,r11,4,57 /* r11 = (r11 << 4) & 0x70 */ - ori r11,r11,0x10 - - /* r10 currently points to an ste one past the group of interest */ - /* make it point to the randomly selected entry */ - subi r10,r10,128 - or r10,r10,r11 /* r10 is the entry to invalidate */ - - isync /* mark the entry invalid */ - ld r11,0(r10) - rldicl r11,r11,56,1 /* clear the valid bit */ - rotldi r11,r11,8 - std r11,0(r10) - sync - - clrrdi r11,r11,28 /* Get the esid part of the ste */ - slbie r11 - -2: std r9,8(r10) /* Store the vsid part of the ste */ - eieio - - mfspr r11,SPRN_DAR /* Get the new esid */ - clrrdi r11,r11,28 /* Permits a full 32b of ESID */ - ori r11,r11,0x90 /* Turn on valid and kp */ - std r11,0(r10) /* Put new entry back into the stab */ - - sync - - /* All done -- return from exception. */ - lwz r9,PACA_EXSLB+EX_CCR(r13) /* get saved CR */ - ld r11,PACA_EXSLB+EX_SRR0(r13) /* get saved SRR0 */ - - andi. r10,r12,MSR_RI - beq- unrecov_slb - - mtcrf 0x80,r9 /* restore CR */ - - mfmsr r10 - clrrdi r10,r10,2 - mtmsrd r10,1 - - mtspr SPRN_SRR0,r11 - mtspr SPRN_SRR1,r12 - ld r9,PACA_EXSLB+EX_R9(r13) - ld r10,PACA_EXSLB+EX_R10(r13) - ld r11,PACA_EXSLB+EX_R11(r13) - ld r12,PACA_EXSLB+EX_R12(r13) - ld r13,PACA_EXSLB+EX_R13(r13) - rfid - b . /* prevent speculative execution */ - -/* - * Space for CPU0's segment table. - * - * On iSeries, the hypervisor must fill in at least one entry before - * we get control (with relocate on). The address is give to the hv - * as a page number (see xLparMap in lpardata.c), so this must be at a - * fixed address (the linker can't compute (u64)&initial_stab >> - * PAGE_SHIFT). - */ - . = STAB0_OFFSET /* 0x6000 */ - .globl initial_stab -initial_stab: - .space 4096 - -/* - * Data area reserved for FWNMI option. - * This address (0x7000) is fixed by the RPA. - */ - .= 0x7000 - .globl fwnmi_data_area -fwnmi_data_area: - - /* iSeries does not use the FWNMI stuff, so it is safe to put - * this here, even if we later allow kernels that will boot on - * both pSeries and iSeries */ -#ifdef CONFIG_PPC_ISERIES - . = LPARMAP_PHYS -#include "lparmap.s" -/* - * This ".text" is here for old compilers that generate a trailing - * .note section when compiling .c files to .s - */ - .text -#endif /* CONFIG_PPC_ISERIES */ - - . = 0x8000 + b generic_secondary_common_init /* - * On pSeries, secondary processors spin in the following code. + * On pSeries and most other platforms, secondary processors spin + * in the following code. * At entry, r3 = this processor's number (physical cpu id) + * + * On Book3E, r4 = 1 to indicate that the initial TLB entry for + * this core already exists (setup via some other mechanism such + * as SCOM before entry). */ -_GLOBAL(pSeries_secondary_smp_init) +_GLOBAL(generic_secondary_smp_init) mr r24,r3 - + mr r25,r4 + /* turn on 64-bit mode */ bl .enable_64b_mode - isync - /* Copy some CPU settings from CPU 0 */ - bl .__restore_cpu_setup + /* get a valid TOC pointer, wherever we're mapped at */ + bl .relative_toc + +#ifdef CONFIG_PPC_BOOK3E + /* Book3E initialization */ + mr r3,r24 + mr r4,r25 + bl .book3e_secondary_core_init +#endif +generic_secondary_common_init: /* Set up a paca value for this processor. Since we have the * physical cpu id in r24, we need to search the pacas to find * which logical id maps to our physical one. */ - LOAD_REG_IMMEDIATE(r13, paca) /* Get base vaddr of paca array */ + LOAD_REG_ADDR(r13, paca) /* Load paca pointer */ + ld r13,0(r13) /* Get base vaddr of paca array */ li r5,0 /* logical cpu id */ 1: lhz r6,PACAHWCPUID(r13) /* Load HW procid from paca */ cmpw r6,r24 /* Compare to our id */ @@ -1474,73 +233,60 @@ _GLOBAL(pSeries_secondary_smp_init) mr r3,r24 /* not found, copy phys to r3 */ b .kexec_wait /* next kernel might do better */ -2: mtspr SPRN_SPRG3,r13 /* Save vaddr of paca in SPRG3 */ +2: mtspr SPRN_SPRG_PACA,r13 /* Save vaddr of paca in an SPRG */ +#ifdef CONFIG_PPC_BOOK3E + addi r12,r13,PACA_EXTLB /* and TLB exc frame in another */ + mtspr SPRN_SPRG_TLB_EXFRAME,r12 +#endif + /* From now on, r24 is expected to be logical cpuid */ mr r24,r5 3: HMT_LOW lbz r23,PACAPROCSTART(r13) /* Test if this processor should */ /* start. */ - sync - - /* Create a temp kernel stack for use before relocation is on. */ - ld r1,PACAEMERGSP(r13) - subi r1,r1,STACK_FRAME_OVERHEAD +#ifndef CONFIG_SMP + b 3b /* Never go on non-SMP */ +#else cmpwi 0,r23,0 -#ifdef CONFIG_SMP - bne .__secondary_start -#endif - b 3b /* Loop until told to go */ + beq 3b /* Loop until told to go */ -#ifdef CONFIG_PPC_ISERIES -_STATIC(__start_initialization_iSeries) - /* Clear out the BSS */ - LOAD_REG_IMMEDIATE(r11,__bss_stop) - LOAD_REG_IMMEDIATE(r8,__bss_start) - sub r11,r11,r8 /* bss size */ - addi r11,r11,7 /* round up to an even double word */ - rldicl. r11,r11,61,3 /* shift right by 3 */ - beq 4f - addi r8,r8,-8 - li r0,0 - mtctr r11 /* zero this many doublewords */ -3: stdu r0,8(r8) - bdnz 3b -4: - LOAD_REG_IMMEDIATE(r1,init_thread_union) - addi r1,r1,THREAD_SIZE - li r0,0 - stdu r0,-STACK_FRAME_OVERHEAD(r1) - - LOAD_REG_IMMEDIATE(r3,cpu_specs) - LOAD_REG_IMMEDIATE(r4,cur_cpu_spec) - li r5,0 - bl .identify_cpu - - LOAD_REG_IMMEDIATE(r2,__toc_start) - addi r2,r2,0x4000 - addi r2,r2,0x4000 - - bl .iSeries_early_setup - bl .early_setup + sync /* order paca.run and cur_cpu_spec */ - /* relocation is on at this point */ + /* See if we need to call a cpu state restore handler */ + LOAD_REG_ADDR(r23, cur_cpu_spec) + ld r23,0(r23) + ld r23,CPU_SPEC_RESTORE(r23) + cmpdi 0,r23,0 + beq 4f + ld r23,0(r23) + mtctr r23 + bctrl - b .start_here_common -#endif /* CONFIG_PPC_ISERIES */ +4: /* Create a temp kernel stack for use before relocation is on. */ + ld r1,PACAEMERGSP(r13) + subi r1,r1,STACK_FRAME_OVERHEAD -#ifdef CONFIG_PPC_MULTIPLATFORM + b __secondary_start +#endif +/* + * Turn the MMU off. + * Assumes we're mapped EA == RA if the MMU is on. + */ +#ifdef CONFIG_PPC_BOOK3S _STATIC(__mmu_off) mfmsr r3 andi. r0,r3,MSR_IR|MSR_DR beqlr + mflr r4 andc r3,r3,r0 mtspr SPRN_SRR0,r4 mtspr SPRN_SRR1,r3 sync rfid b . /* prevent speculative execution */ +#endif /* @@ -1555,35 +301,54 @@ _STATIC(__mmu_off) * */ _GLOBAL(__start_initialization_multiplatform) -#ifdef CONFIG_PPC_MULTIPLATFORM + /* Make sure we are running in 64 bits mode */ + bl .enable_64b_mode + + /* Get TOC pointer (current runtime address) */ + bl .relative_toc + + /* find out where we are now */ + bcl 20,31,$+4 +0: mflr r26 /* r26 = runtime addr here */ + addis r26,r26,(_stext - 0b)@ha + addi r26,r26,(_stext - 0b)@l /* current runtime base addr */ + /* * Are we booted from a PROM Of-type client-interface ? */ cmpldi cr0,r5,0 - bne .__boot_from_prom /* yes -> prom */ -#endif - + beq 1f + b .__boot_from_prom /* yes -> prom */ +1: /* Save parameters */ mr r31,r3 mr r30,r4 - /* Make sure we are running in 64 bits mode */ - bl .enable_64b_mode - +#ifdef CONFIG_PPC_BOOK3E + bl .start_initialization_book3e + b .__after_prom_start +#else /* Setup some critical 970 SPRs before switching MMU off */ - bl .__970_cpu_preinit - - /* cpu # */ - li r24,0 + mfspr r0,SPRN_PVR + srwi r0,r0,16 + cmpwi r0,0x39 /* 970 */ + beq 1f + cmpwi r0,0x3c /* 970FX */ + beq 1f + cmpwi r0,0x44 /* 970MP */ + beq 1f + cmpwi r0,0x45 /* 970GX */ + bne 2f +1: bl .__cpu_preinit_ppc970 +2: - /* Switch off MMU if not already */ - LOAD_REG_IMMEDIATE(r4, .__after_prom_start - KERNELBASE) - add r4,r4,r30 + /* Switch off MMU if not already off */ bl .__mmu_off b .__after_prom_start +#endif /* CONFIG_PPC_BOOK3E */ -#ifdef CONFIG_PPC_MULTIPLATFORM -_STATIC(__boot_from_prom) +_INIT_STATIC(__boot_from_prom) +#ifdef CONFIG_PPC_OF_BOOT_TRAMPOLINE /* Save parameters */ mr r31,r3 mr r30,r4 @@ -1594,22 +359,15 @@ _STATIC(__boot_from_prom) /* * Align the stack to 16-byte boundary * Depending on the size and layout of the ELF sections in the initial - * boot binary, the stack pointer will be unalignet on PowerMac + * boot binary, the stack pointer may be unaligned on PowerMac */ rldicr r1,r1,0,59 - /* Make sure we are running in 64 bits mode */ - bl .enable_64b_mode - - /* put a relocation offset into r3 */ - bl .reloc_offset - - LOAD_REG_IMMEDIATE(r2,__toc_start) - addi r2,r2,0x4000 - addi r2,r2,0x4000 - - /* Relocate the TOC from a virt addr to a real addr */ - add r2,r2,r3 +#ifdef CONFIG_RELOCATABLE + /* Relocate code for where we are now */ + mr r3,r26 + bl .relocate +#endif /* Restore parameters */ mr r3,r31 @@ -1619,63 +377,81 @@ _STATIC(__boot_from_prom) mr r7,r27 /* Do all of the interaction with OF client interface */ + mr r8,r26 bl .prom_init - /* We never return */ +#endif /* #CONFIG_PPC_OF_BOOT_TRAMPOLINE */ + + /* We never return. We also hit that trap if trying to boot + * from OF while CONFIG_PPC_OF_BOOT_TRAMPOLINE isn't selected */ trap -#endif -/* - * At this point, r3 contains the physical address we are running at, - * returned by prom_init() - */ _STATIC(__after_prom_start) +#ifdef CONFIG_RELOCATABLE + /* process relocations for the final address of the kernel */ + lis r25,PAGE_OFFSET@highest /* compute virtual base of kernel */ + sldi r25,r25,32 +#ifdef CONFIG_CRASH_DUMP + lwz r7,__run_at_load-_stext(r26) + cmplwi cr0,r7,1 /* kdump kernel ? - stay where we are */ + bne 1f + add r25,r25,r26 +#endif +1: mr r3,r25 + bl .relocate +#endif /* - * We need to run with __start at physical address PHYSICAL_START. + * We need to run with _stext at physical address PHYSICAL_START. * This will leave some code in the first 256B of * real memory, which are reserved for software use. - * The remainder of the first page is loaded with the fixed - * interrupt vectors. The next two pages are filled with - * unknown exception placeholders. * * Note: This process overwrites the OF exception vectors. - * r26 == relocation offset - * r27 == KERNELBASE */ - bl .reloc_offset - mr r26,r3 - LOAD_REG_IMMEDIATE(r27, KERNELBASE) - - LOAD_REG_IMMEDIATE(r3, PHYSICAL_START) /* target addr */ - - // XXX FIXME: Use phys returned by OF (r30) - add r4,r27,r26 /* source addr */ - /* current address of _start */ - /* i.e. where we are running */ - /* the source addr */ - - LOAD_REG_IMMEDIATE(r5,copy_to_here) /* # bytes of memory to copy */ - sub r5,r5,r27 - + li r3,0 /* target addr */ +#ifdef CONFIG_PPC_BOOK3E + tovirt(r3,r3) /* on booke, we already run at PAGE_OFFSET */ +#endif + mr. r4,r26 /* In some cases the loader may */ + beq 9f /* have already put us at zero */ li r6,0x100 /* Start offset, the first 0x100 */ /* bytes were copied earlier. */ +#ifdef CONFIG_PPC_BOOK3E + tovirt(r6,r6) /* on booke, we already run at PAGE_OFFSET */ +#endif + +#ifdef CONFIG_CRASH_DUMP +/* + * Check if the kernel has to be running as relocatable kernel based on the + * variable __run_at_load, if it is set the kernel is treated as relocatable + * kernel, otherwise it will be moved to PHYSICAL_START + */ + lwz r7,__run_at_load-_stext(r26) + cmplwi cr0,r7,1 + bne 3f + + li r5,__end_interrupts - _stext /* just copy interrupts */ + b 5f +3: +#endif + lis r5,(copy_to_here - _stext)@ha + addi r5,r5,(copy_to_here - _stext)@l /* # bytes of memory to copy */ bl .copy_and_flush /* copy the first n bytes */ /* this includes the code being */ /* executed here. */ - - LOAD_REG_IMMEDIATE(r0, 4f) /* Jump to the copy of this code */ - mtctr r0 /* that we just made/relocated */ + addis r8,r3,(4f - _stext)@ha /* Jump to the copy of this code */ + addi r8,r8,(4f - _stext)@l /* that we just made */ + mtctr r8 bctr -4: LOAD_REG_IMMEDIATE(r5,klimit) - add r5,r5,r26 - ld r5,0(r5) /* get the value of klimit */ - sub r5,r5,r27 - bl .copy_and_flush /* copy the rest */ - b .start_here_multiplatform +p_end: .llong _end - _stext + +4: /* Now copy the rest of the kernel up to _end */ + addis r5,r26,(p_end - _stext)@ha + ld r5,(p_end - _stext)@l(r5) /* get _end */ +5: bl .copy_and_flush /* copy the rest */ -#endif /* CONFIG_PPC_MULTIPLATFORM */ +9: b .start_here_multiplatform /* * Copy routine used to copy the kernel to start at physical address 0 @@ -1688,7 +464,7 @@ _STATIC(__after_prom_start) _GLOBAL(copy_and_flush) addi r5,r5,-8 addi r6,r6,-8 -4: li r0,16 /* Use the least common */ +4: li r0,8 /* Use the smallest common */ /* denominator cache line */ /* size. This results in */ /* extra cache line flushes */ @@ -1739,10 +515,21 @@ __secondary_start_pmac_0: _GLOBAL(pmac_secondary_start) /* turn on 64-bit mode */ bl .enable_64b_mode + + li r0,0 + mfspr r3,SPRN_HID4 + rldimi r3,r0,40,23 /* clear bit 23 (rm_ci) */ + sync + mtspr SPRN_HID4,r3 isync + sync + slbia + + /* get TOC pointer (real address) */ + bl .relative_toc /* Copy some CPU settings from CPU 0 */ - bl .__restore_cpu_setup + bl .__restore_cpu_ppc970 /* pSeries do that early though I don't think we really need it */ mfmsr r3 @@ -1750,16 +537,17 @@ _GLOBAL(pmac_secondary_start) mtmsrd r3 /* RI on */ /* Set up a paca value for this processor. */ - LOAD_REG_IMMEDIATE(r4, paca) /* Get base vaddr of paca array */ - mulli r13,r24,PACA_SIZE /* Calculate vaddr of right paca */ + LOAD_REG_ADDR(r4,paca) /* Load paca pointer */ + ld r4,0(r4) /* Get base vaddr of paca array */ + mulli r13,r24,PACA_SIZE /* Calculate vaddr of right paca */ add r13,r13,r4 /* for this processor. */ - mtspr SPRN_SPRG3,r13 /* Save vaddr of paca in SPRG3 */ + mtspr SPRN_SPRG_PACA,r13 /* Save vaddr of paca in an SPRG*/ /* Create a temp kernel stack for use before relocation is on. */ ld r1,PACAEMERGSP(r13) subi r1,r1,STACK_FRAME_OVERHEAD - b .__secondary_start + b __secondary_start #endif /* CONFIG_PPC_PMAC */ @@ -1771,18 +559,19 @@ _GLOBAL(pmac_secondary_start) * 1. Processor number * 2. Segment table pointer (virtual address) * On entry the following are set: - * r1 = stack pointer. vaddr for iSeries, raddr (temp stack) for pSeries - * r24 = cpu# (in Linux terms) - * r13 = paca virtual address - * SPRG3 = paca virtual address + * r1 = stack pointer. vaddr for iSeries, raddr (temp stack) for pSeries + * r24 = cpu# (in Linux terms) + * r13 = paca virtual address + * SPRG_PACA = paca virtual address */ -_GLOBAL(__secondary_start) + .section ".text"; + .align 2 ; + + .globl __secondary_start +__secondary_start: /* Set thread priority to MEDIUM */ HMT_MEDIUM - /* Load TOC */ - ld r2,PACATOC(r13) - /* Do early setup for that CPU (stab, slb, hash table pointer) */ bl .early_setup_secondary @@ -1800,19 +589,41 @@ _GLOBAL(__secondary_start) /* enable MMU and jump to start_secondary */ LOAD_REG_ADDR(r3, .start_secondary_prolog) LOAD_REG_IMMEDIATE(r4, MSR_KERNEL) -#ifdef DO_SOFT_DISABLE +#ifdef CONFIG_PPC_ISERIES +BEGIN_FW_FTR_SECTION ori r4,r4,MSR_EE + li r8,1 + stb r8,PACAHARDIRQEN(r13) +END_FW_FTR_SECTION_IFSET(FW_FEATURE_ISERIES) #endif +BEGIN_FW_FTR_SECTION + stb r7,PACAHARDIRQEN(r13) +END_FW_FTR_SECTION_IFCLR(FW_FEATURE_ISERIES) + stb r7,PACASOFTIRQEN(r13) + mtspr SPRN_SRR0,r3 mtspr SPRN_SRR1,r4 - rfid + RFI b . /* prevent speculative execution */ /* * Running with relocation on at this point. All we want to do is - * zero the stack back-chain pointer before going into C code. + * zero the stack back-chain pointer and get the TOC virtual address + * before going into C code. */ _GLOBAL(start_secondary_prolog) + ld r2,PACATOC(r13) + li r3,0 + std r3,0(r1) /* Zero the stack frame pointer */ + bl .start_secondary + b . +/* + * Reset stack pointer and call start_secondary + * to continue with online operation when woken up + * from cede in cpu offline. + */ +_GLOBAL(start_secondary_resume) + ld r1,PACAKSAVE(r13) /* Reload kernel stack pointer */ li r3,0 std r3,0(r1) /* Zero the stack frame pointer */ bl .start_secondary @@ -1824,35 +635,51 @@ _GLOBAL(start_secondary_prolog) */ _GLOBAL(enable_64b_mode) mfmsr r11 /* grab the current MSR */ - li r12,1 - rldicr r12,r12,MSR_SF_LG,(63-MSR_SF_LG) - or r11,r11,r12 - li r12,1 - rldicr r12,r12,MSR_ISF_LG,(63-MSR_ISF_LG) +#ifdef CONFIG_PPC_BOOK3E + oris r11,r11,0x8000 /* CM bit set, we'll set ICM later */ + mtmsr r11 +#else /* CONFIG_PPC_BOOK3E */ + li r12,(MSR_SF | MSR_ISF)@highest + sldi r12,r12,48 or r11,r11,r12 mtmsrd r11 isync +#endif + blr + +/* + * This puts the TOC pointer into r2, offset by 0x8000 (as expected + * by the toolchain). It computes the correct value for wherever we + * are running at the moment, using position-independent code. + */ +_GLOBAL(relative_toc) + mflr r0 + bcl 20,31,$+4 +0: mflr r9 + ld r2,(p_toc - 0b)(r9) + add r2,r2,r9 + mtlr r0 blr -#ifdef CONFIG_PPC_MULTIPLATFORM +p_toc: .llong __toc_start + 0x8000 - 0b + /* * This is where the main kernel code starts. */ -_STATIC(start_here_multiplatform) - /* get a new offset, now that the kernel has moved. */ - bl .reloc_offset - mr r26,r3 +_INIT_STATIC(start_here_multiplatform) + /* set up the TOC (real address) */ + bl .relative_toc /* Clear out the BSS. It may have been done in prom_init, * already but that's irrelevant since prom_init will soon * be detached from the kernel completely. Besides, we need * to clear it now for kexec-style entry. */ - LOAD_REG_IMMEDIATE(r11,__bss_stop) - LOAD_REG_IMMEDIATE(r8,__bss_start) + LOAD_REG_ADDR(r11,__bss_stop) + LOAD_REG_ADDR(r8,__bss_start) sub r11,r11,r8 /* bss size */ addi r11,r11,7 /* round up to an even double word */ - rldicl. r11,r11,61,3 /* shift right by 3 */ + srdi. r11,r11,3 /* shift right by 3 */ beq 4f addi r8,r8,-8 li r0,0 @@ -1861,122 +688,75 @@ _STATIC(start_here_multiplatform) bdnz 3b 4: +#ifndef CONFIG_PPC_BOOK3E mfmsr r6 ori r6,r6,MSR_RI mtmsrd r6 /* RI on */ +#endif + +#ifdef CONFIG_RELOCATABLE + /* Save the physical address we're running at in kernstart_addr */ + LOAD_REG_ADDR(r4, kernstart_addr) + clrldi r0,r25,2 + std r0,0(r4) +#endif - /* The following gets the stack and TOC set up with the regs */ + /* The following gets the stack set up with the regs */ /* pointing to the real addr of the kernel stack. This is */ /* all done to support the C function call below which sets */ /* up the htab. This is done because we have relocated the */ /* kernel but are still running in real mode. */ - LOAD_REG_IMMEDIATE(r3,init_thread_union) - add r3,r3,r26 + LOAD_REG_ADDR(r3,init_thread_union) - /* set up a stack pointer (physical address) */ + /* set up a stack pointer */ addi r1,r3,THREAD_SIZE li r0,0 stdu r0,-STACK_FRAME_OVERHEAD(r1) - /* set up the TOC (physical address) */ - LOAD_REG_IMMEDIATE(r2,__toc_start) - addi r2,r2,0x4000 - addi r2,r2,0x4000 - add r2,r2,r26 - - LOAD_REG_IMMEDIATE(r3, cpu_specs) - add r3,r3,r26 - LOAD_REG_IMMEDIATE(r4,cur_cpu_spec) - add r4,r4,r26 - mr r5,r26 - bl .identify_cpu - - /* Save some low level config HIDs of CPU0 to be copied to - * other CPUs later on, or used for suspend/resume - */ - bl .__save_cpu_setup - sync - /* Do very early kernel initializations, including initial hash table, * stab and slb setup before we turn on relocation. */ /* Restore parameters passed from prom_init/kexec */ mr r3,r31 - bl .early_setup + bl .early_setup /* also sets r13 and SPRG_PACA */ - LOAD_REG_IMMEDIATE(r3, .start_here_common) - LOAD_REG_IMMEDIATE(r4, MSR_KERNEL) + LOAD_REG_ADDR(r3, .start_here_common) + ld r4,PACAKMSR(r13) mtspr SPRN_SRR0,r3 mtspr SPRN_SRR1,r4 - rfid + RFI b . /* prevent speculative execution */ -#endif /* CONFIG_PPC_MULTIPLATFORM */ /* This is where all platforms converge execution */ -_STATIC(start_here_common) +_INIT_GLOBAL(start_here_common) /* relocation is on at this point */ + std r1,PACAKSAVE(r13) - /* The following code sets up the SP and TOC now that we are */ - /* running with translation enabled. */ - - LOAD_REG_IMMEDIATE(r3,init_thread_union) - - /* set up the stack */ - addi r1,r3,THREAD_SIZE - li r0,0 - stdu r0,-STACK_FRAME_OVERHEAD(r1) - - /* Apply the CPUs-specific fixups (nop out sections not relevant - * to this CPU - */ - li r3,0 - bl .do_cpu_ftr_fixups - - LOAD_REG_IMMEDIATE(r26, boot_cpuid) - lwz r26,0(r26) - - LOAD_REG_IMMEDIATE(r24, paca) /* Get base vaddr of paca array */ - mulli r13,r26,PACA_SIZE /* Calculate vaddr of right paca */ - add r13,r13,r24 /* for this processor. */ - mtspr SPRN_SPRG3,r13 - - /* ptr to current */ - LOAD_REG_IMMEDIATE(r4, init_task) - std r4,PACACURRENT(r13) - - /* Load the TOC */ + /* Load the TOC (virtual address) */ ld r2,PACATOC(r13) - std r1,PACAKSAVE(r13) bl .setup_system /* Load up the kernel context */ 5: -#ifdef DO_SOFT_DISABLE li r5,0 - stb r5,PACAPROCENABLED(r13) /* Soft Disabled */ + stb r5,PACASOFTIRQEN(r13) /* Soft Disabled */ +#ifdef CONFIG_PPC_ISERIES +BEGIN_FW_FTR_SECTION mfmsr r5 - ori r5,r5,MSR_EE /* Hard Enabled */ + ori r5,r5,MSR_EE /* Hard Enabled on iSeries*/ mtmsrd r5 + li r5,1 +END_FW_FTR_SECTION_IFSET(FW_FEATURE_ISERIES) #endif + stb r5,PACAHARDIRQEN(r13) /* Hard Disabled on others */ - bl .start_kernel + bl .start_kernel /* Not reached */ BUG_OPCODE -/* Put the paca pointer into r13 and SPRG3 */ -_GLOBAL(setup_boot_paca) - LOAD_REG_IMMEDIATE(r3, boot_cpuid) - lwz r3,0(r3) - LOAD_REG_IMMEDIATE(r4, paca) /* Get base vaddr of paca array */ - mulli r3,r3,PACA_SIZE /* Calculate vaddr of right paca */ - add r13,r3,r4 /* for this processor. */ - mtspr SPRN_SPRG3,r13 - - blr - /* * We put a few things here that have to be page-aligned. * This stuff goes at the beginning of the bss, which is page-aligned. @@ -1991,12 +771,4 @@ empty_zero_page: .globl swapper_pg_dir swapper_pg_dir: - .space PAGE_SIZE - -/* - * This space gets a copy of optional info passed to us by the bootstrap - * Used to pass parameters into the kernel like root=/dev/sda1, etc. - */ - .globl cmd_line -cmd_line: - .space COMMAND_LINE_SIZE + .space PGD_TABLE_SIZE