X-Git-Url: http://ftp.safe.ca/?a=blobdiff_plain;f=Documentation%2Fkprobes.txt;h=053037a1fe6d3b4943219c55d82dafca593c8d03;hb=16c01b20ae0572d5a1fe8059f1b4c09f79b73cbf;hp=a79633d702bff23230bb0d76cb68565e078b4fb2;hpb=f82796214a95b1ec00c2f121c1080d10f2b099a1;p=safe%2Fjmp%2Flinux-2.6

diff --git a/Documentation/kprobes.txt b/Documentation/kprobes.txt
index a79633d..053037a 100644
--- a/Documentation/kprobes.txt
+++ b/Documentation/kprobes.txt
@@ -212,7 +212,9 @@ hit, Kprobes calls kp->pre_handler.  After the probed instruction
 is single-stepped, Kprobe calls kp->post_handler.  If a fault
 occurs during execution of kp->pre_handler or kp->post_handler,
 or during single-stepping of the probed instruction, Kprobes calls
-kp->fault_handler.  Any or all handlers can be NULL.
+kp->fault_handler.  Any or all handlers can be NULL. If kp->flags
+is set KPROBE_FLAG_DISABLED, that kp will be registered but disabled,
+so, it's handlers aren't hit until calling enable_kprobe(kp).
 
 NOTE:
 1. With the introduction of the "symbol_name" field to struct kprobe,
@@ -363,6 +365,26 @@ probes) in the specified array, they clear the addr field of those
 incorrect probes. However, other probes in the array are
 unregistered correctly.
 
+4.7 disable_*probe
+
+#include <linux/kprobes.h>
+int disable_kprobe(struct kprobe *kp);
+int disable_kretprobe(struct kretprobe *rp);
+int disable_jprobe(struct jprobe *jp);
+
+Temporarily disables the specified *probe. You can enable it again by using
+enable_*probe(). You must specify the probe which has been registered.
+
+4.8 enable_*probe
+
+#include <linux/kprobes.h>
+int enable_kprobe(struct kprobe *kp);
+int enable_kretprobe(struct kretprobe *rp);
+int enable_jprobe(struct jprobe *jp);
+
+Enables *probe which has been disabled by disable_*probe(). You must specify
+the probe which has been registered.
+
 5. Kprobes Features and Limitations
 
 Kprobes allows multiple probes at the same address.  Currently,
@@ -485,9 +507,9 @@ http://www.linuxsymposium.org/2006/linuxsymposium_procv2.pdf (pages 101-115)
 Appendix A: The kprobes debugfs interface
 
 With recent kernels (> 2.6.20) the list of registered kprobes is visible
-under the /debug/kprobes/ directory (assuming debugfs is mounted at /debug).
+under the /sys/kernel/debug/kprobes/ directory (assuming debugfs is mounted at //sys/kernel/debug).
 
-/debug/kprobes/list: Lists all registered probes on the system
+/sys/kernel/debug/kprobes/list: Lists all registered probes on the system
 
 c015d71a  k  vfs_read+0x0
 c011a316  j  do_fork+0x0
@@ -497,10 +519,17 @@ The first column provides the kernel address where the probe is inserted.
 The second column identifies the type of probe (k - kprobe, r - kretprobe
 and j - jprobe), while the third column specifies the symbol+offset of
 the probe. If the probed function belongs to a module, the module name
-is also specified.
-
-/debug/kprobes/enabled: Turn kprobes ON/OFF
-
-Provides a knob to globally turn registered kprobes ON or OFF. By default,
-all kprobes are enabled. By echoing "0" to this file, all registered probes
-will be disarmed, till such time a "1" is echoed to this file.
+is also specified. Following columns show probe status. If the probe is on
+a virtual address that is no longer valid (module init sections, module
+virtual addresses that correspond to modules that've been unloaded),
+such probes are marked with [GONE]. If the probe is temporarily disabled,
+such probes are marked with [DISABLED].
+
+/sys/kernel/debug/kprobes/enabled: Turn kprobes ON/OFF forcibly.
+
+Provides a knob to globally and forcibly turn registered kprobes ON or OFF.
+By default, all kprobes are enabled. By echoing "0" to this file, all
+registered probes will be disarmed, till such time a "1" is echoed to this
+file. Note that this knob just disarms and arms all kprobes and doesn't
+change each probe's disabling state. This means that disabled kprobes (marked
+[DISABLED]) will be not enabled if you turn ON all kprobes by this knob.