X-Git-Url: http://ftp.safe.ca/?a=blobdiff_plain;f=Documentation%2Fkernel-parameters.txt;h=e4cbca58536c9f3ab4236f4db78eb22cacc993af;hb=d4509e5a6edf8862c18d887a642ce4994bde297d;hp=5bf45c0ac749038b062b4a5de25715bfa38059e1;hpb=016ddd9b5b315fe52ac6ba3167521f50b3868d34;p=safe%2Fjmp%2Flinux-2.6

diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt
index 5bf45c0..e4cbca5 100644
--- a/Documentation/kernel-parameters.txt
+++ b/Documentation/kernel-parameters.txt
@@ -54,6 +54,7 @@ parameter is applicable:
 	IMA     Integrity measurement architecture is enabled.
 	IOSCHED	More than one I/O scheduler is enabled.
 	IP_PNP	IP DHCP, BOOTP, or RARP is enabled.
+	IPV6	IPv6 support is enabled.
 	ISAPNP	ISA PnP code is enabled.
 	ISDN	Appropriate ISDN support is enabled.
 	JOY	Appropriate joystick support is enabled.
@@ -311,6 +312,11 @@ and is between 256 and 4096 characters. It is defined in the file
 	aic79xx=	[HW,SCSI]
 			See Documentation/scsi/aic79xx.txt.
 
+	alignment=	[KNL,ARM]
+			Allow the default userspace alignment fault handler
+			behaviour to be specified.  Bit 0 enables warnings,
+			bit 1 enables fixups, and bit 2 sends a segfault.
+
 	amd_iommu=	[HW,X86-84]
 			Pass parameters to the AMD IOMMU driver in the system.
 			Possible values are:
@@ -347,6 +353,9 @@ and is between 256 and 4096 characters. It is defined in the file
 			Change the amount of debugging information output
 			when initialising the APIC and IO-APIC components.
 
+	autoconf=	[IPV6]
+			See Documentation/networking/ipv6.txt.
+
 	show_lapic=	[APIC,X86] Advanced Programmable Interrupt Controller
 			Limit apic dumping. The parameter defines the maximal
 			number of local apics being dumped. Also it is possible
@@ -629,6 +638,12 @@ and is between 256 and 4096 characters. It is defined in the file
 			See drivers/char/README.epca and
 			Documentation/serial/digiepca.txt.
 
+	disable=	[IPV6]
+			See Documentation/networking/ipv6.txt.
+
+	disable_ipv6=	[IPV6]
+			See Documentation/networking/ipv6.txt.
+
 	disable_mtrr_cleanup [X86]
 			The kernel tries to adjust MTRR layout from continuous
 			to discrete, to make X server driver able to add WB
@@ -1775,6 +1790,12 @@ and is between 256 and 4096 characters. It is defined in the file
 			purges which is reported from either PAL_VM_SUMMARY or
 			SAL PALO.
 
+	nr_cpus=	[SMP] Maximum number of processors that	an SMP kernel
+			could support.  nr_cpus=n : n >= 1 limits the kernel to
+			supporting 'n' processors. Later in runtime you can not
+			use hotplug cpu feature to put more cpu back to online.
+			just like you compile the kernel NR_CPUS=n
+
 	nr_uarts=	[SERIAL] maximum number of UARTs to be registered.
 
 	numa_zonelist_order= [KNL, BOOT] Select zonelist order for NUMA.
@@ -1942,8 +1963,12 @@ and is between 256 and 4096 characters. It is defined in the file
 				IRQ routing is enabled.
 		noacpi		[X86] Do not use ACPI for IRQ routing
 				or for PCI scanning.
-		use_crs		[X86] Use _CRS for PCI resource
-				allocation.
+		use_crs		[X86] Use PCI host bridge window information
+				from ACPI.  On BIOSes from 2008 or later, this
+				is enabled by default.  If you need to use this,
+				please report a bug.
+		nocrs		[X86] Ignore PCI host bridge windows from ACPI.
+			        If you need to use this, please report a bug.
 		routeirq	Do IRQ routing for all PCI devices.
 				This is normally done in pci_enable_device(),
 				so this option is a temporary workaround
@@ -1992,6 +2017,14 @@ and is between 256 and 4096 characters. It is defined in the file
 		force	Enable ASPM even on devices that claim not to support it.
 			WARNING: Forcing ASPM on may cause system lockups.
 
+	pcie_pme=	[PCIE,PM] Native PCIe PME signaling options:
+		off	Do not use native PCIe PME signaling.
+		force	Use native PCIe PME signaling even if the BIOS refuses
+			to allow the kernel to control the relevant PCIe config
+			registers.
+		nomsi	Do not use MSI for native PCIe PME signaling (this makes
+			all PCIe root ports use INTx for everything).
+
 	pcmv=		[HW,PCMCIA] BadgePAD 4
 
 	pd.		[PARIDE]
@@ -2697,6 +2730,13 @@ and is between 256 and 4096 characters. It is defined in the file
 					medium is write-protected).
 			Example: quirks=0419:aaf5:rl,0421:0433:rc
 
+	userpte=
+			[X86] Flags controlling user PTE allocations.
+
+				nohigh = do not allocate PTE pages in
+					HIGHMEM regardless of setting
+					of CONFIG_HIGHPTE.
+
 	vdso=		[X86,SH]
 			vdso=2: enable compat VDSO (default with COMPAT_VDSO)
 			vdso=1: enable VDSO (default)
@@ -2790,6 +2830,12 @@ and is between 256 and 4096 characters. It is defined in the file
 			default x2apic cluster mode on platforms
 			supporting x2apic.
 
+	x86_mrst_timer= [X86-32,APBT]
+			Choose timer option for x86 Moorestown MID platform.
+			Two valid options are apbt timer only and lapic timer
+			plus one apbt timer for broadcast timer.
+			x86_mrst_timer=apbt_only | lapic_and_apbt
+
 	xd=		[HW,XT] Original XT pre-IDE (RLL encoded) disks.
 	xd_geo=		See header of drivers/block/xd.c.