X-Git-Url: http://ftp.safe.ca/?a=blobdiff_plain;f=Documentation%2Fkernel-parameters.txt;h=b12bacd252fc92b2c737fdcc1ecb4c9390161e95;hb=adff687d8cb0ed62b147a7e1d277846b3130d593;hp=3bc48b0bd3a979e857287115d2893b068abb8b58;hpb=322aafa6645a48c3b7837ca7385f126ab78127fd;p=safe%2Fjmp%2Flinux-2.6

diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt
index 3bc48b0..b12bacd 100644
--- a/Documentation/kernel-parameters.txt
+++ b/Documentation/kernel-parameters.txt
@@ -99,6 +99,7 @@ parameter is applicable:
 	SWSUSP	Software suspend (hibernation) is enabled.
 	SUSPEND	System suspend states are enabled.
 	FTRACE	Function tracing enabled.
+	TPM	TPM drivers are enabled.
 	TS	Appropriate touchscreen support is enabled.
 	UMS	USB Mass Storage support is enabled.
 	USB	USB support is enabled.
@@ -151,6 +152,7 @@ and is between 256 and 4096 characters. It is defined in the file
 			strict -- Be less tolerant of platforms that are not
 				strictly ACPI specification compliant.
 			rsdt -- prefer RSDT over (default) XSDT
+			copy_dsdt -- copy DSDT to memory
 
 			See also Documentation/power/pm.txt, pci=noacpi
 
@@ -200,10 +202,6 @@ and is between 256 and 4096 characters. It is defined in the file
 			acpi_display_output=video
 			See above.
 
-	acpi_early_pdc_eval	[HW,ACPI] Evaluate processor _PDC methods
-				early. Needed on some platforms to properly
-				initialize the EC.
-
 	acpi_irq_balance [HW,ACPI]
 			ACPI will balance active IRQs
 			default in APIC mode
@@ -324,15 +322,12 @@ and is between 256 and 4096 characters. It is defined in the file
 	amd_iommu=	[HW,X86-84]
 			Pass parameters to the AMD IOMMU driver in the system.
 			Possible values are:
-			isolate - enable device isolation (each device, as far
-			          as possible, will get its own protection
-			          domain) [default]
-			share - put every device behind one IOMMU into the
-				same protection domain
 			fullflush - enable flushing of IO/TLB entries when
 				    they are unmapped. Otherwise they are
 				    flushed before they will be reused, which
 				    is a lot of faster
+			off	  - do not initialize any AMD IOMMU found in
+				    the system
 
 	amijoy.map=	[HW,JOY] Amiga joystick support
 			Map of devices attached to JOY0DAT and JOY1DAT
@@ -793,8 +788,12 @@ and is between 256 and 4096 characters. It is defined in the file
 			as early as possible in order to facilitate early
 			boot debugging.
 
-	ftrace_dump_on_oops
+	ftrace_dump_on_oops[=orig_cpu]
 			[FTRACE] will dump the trace buffers on oops.
+			If no parameter is passed, ftrace will dump
+			buffers of all CPUs, but if you pass orig_cpu, it will
+			dump only the buffer of the CPU that triggered the
+			oops.
 
 	ftrace_filter=[function-list]
 			[FTRACE] Limit the functions traced by the function
@@ -1203,7 +1202,7 @@ and is between 256 and 4096 characters. It is defined in the file
 
 	libata.force=	[LIBATA] Force configurations.  The format is comma
 			separated list of "[ID:]VAL" where ID is
-			PORT[:DEVICE].  PORT and DEVICE are decimal numbers
+			PORT[.DEVICE].  PORT and DEVICE are decimal numbers
 			matching port, link or device.  Basically, it matches
 			the ATA ID string printed on console by libata.  If
 			the whole ID part is omitted, the last PORT and DEVICE
@@ -2619,6 +2618,15 @@ and is between 256 and 4096 characters. It is defined in the file
 
 	tp720=		[HW,PS2]
 
+	tpm_suspend_pcr=[HW,TPM]
+			Format: integer pcr id
+			Specify that at suspend time, the tpm driver
+			should extend the specified pcr with zeros,
+			as a workaround for some chips which fail to
+			flush the last written pcr on TPM_SaveState.
+			This will guarantee that all the other pcrs
+			are saved.
+
 	trace_buf_size=nn[KMG]
 			[FTRACE] will set tracing buffer size.