X-Git-Url: http://ftp.safe.ca/?a=blobdiff_plain;f=Documentation%2Fkernel-parameters.txt;h=839b21b0699ac10a1991c47455cddd05ced6491b;hb=3374cd1abd478f767aaedf2c21d109596ff0fe72;hp=0bf8a882ee9e18eb1bfba3ca05de68137211d1d8;hpb=d614aec4752f8c61b2e7cb77806b6bd59aa50836;p=safe%2Fjmp%2Flinux-2.6 diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index 0bf8a88..839b21b 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -48,14 +48,17 @@ parameter is applicable: EFI EFI Partitioning (GPT) is enabled EIDE EIDE/ATAPI support is enabled. FB The frame buffer device is enabled. + GCOV GCOV profiling is enabled. HW Appropriate hardware is enabled. IA-64 IA-64 architecture is enabled. IMA Integrity measurement architecture is enabled. IOSCHED More than one I/O scheduler is enabled. IP_PNP IP DHCP, BOOTP, or RARP is enabled. + IPV6 IPv6 support is enabled. ISAPNP ISA PnP code is enabled. ISDN Appropriate ISDN support is enabled. JOY Appropriate joystick support is enabled. + KVM Kernel Virtual Machine support is enabled. LIBATA Libata driver is enabled LP Printer support is enabled. LOOP Loopback device support is enabled. @@ -83,7 +86,6 @@ parameter is applicable: PPT Parallel port support is enabled. PS2 Appropriate PS/2 support is enabled. RAM RAM disk support is enabled. - ROOTPLUG The example Root Plug LSM is enabled. S390 S390 architecture is enabled. SCSI Appropriate SCSI support is enabled. A lot of drivers has their options described inside of @@ -228,14 +230,6 @@ and is between 256 and 4096 characters. It is defined in the file to assume that this machine's pmtimer latches its value and always returns good values. - acpi.power_nocheck= [HW,ACPI] - Format: 1/0 enable/disable the check of power state. - On some bogus BIOS the _PSC object/_STA object of - power resource can't return the correct device power - state. In such case it is unneccessary to check its - power state again in power transition. - 1 : disable the power state check - acpi_sci= [HW,ACPI] ACPI System Control Interrupt trigger mode Format: { level | edge | high | low } @@ -247,7 +241,7 @@ and is between 256 and 4096 characters. It is defined in the file acpi_sleep= [HW,ACPI] Sleep options Format: { s3_bios, s3_mode, s3_beep, s4_nohwsig, - old_ordering, s4_nonvs } + old_ordering, s4_nonvs, sci_force_enable } See Documentation/power/video.txt for information on s3_bios and s3_mode. s3_beep is for debugging; it makes the PC's speaker beep @@ -260,6 +254,9 @@ and is between 256 and 4096 characters. It is defined in the file of _PTS is used by default). s4_nonvs prevents the kernel from saving/restoring the ACPI NVS memory during hibernation. + sci_force_enable causes the kernel to set SCI_EN directly + on resume from S1/S3 (which is against the ACPI spec, + but some broken systems don't work without it). acpi_use_timer_override [HW,ACPI] Use timer override. For some broken Nvidia NF5 boards @@ -315,14 +312,14 @@ and is between 256 and 4096 characters. It is defined in the file aic79xx= [HW,SCSI] See Documentation/scsi/aic79xx.txt. + alignment= [KNL,ARM] + Allow the default userspace alignment fault handler + behaviour to be specified. Bit 0 enables warnings, + bit 1 enables fixups, and bit 2 sends a segfault. + amd_iommu= [HW,X86-84] Pass parameters to the AMD IOMMU driver in the system. Possible values are: - isolate - enable device isolation (each device, as far - as possible, will get its own protection - domain) [default] - share - put every device behind one IOMMU into the - same protection domain fullflush - enable flushing of IO/TLB entries when they are unmapped. Otherwise they are flushed before they will be reused, which @@ -351,6 +348,18 @@ and is between 256 and 4096 characters. It is defined in the file Change the amount of debugging information output when initialising the APIC and IO-APIC components. + autoconf= [IPV6] + See Documentation/networking/ipv6.txt. + + show_lapic= [APIC,X86] Advanced Programmable Interrupt Controller + Limit apic dumping. The parameter defines the maximal + number of local apics being dumped. Also it is possible + to set it to "all" by meaning -- no limit here. + Format: { 1 (default) | 2 | ... | all }. + The parameter valid if only apic=debug or + apic=verbose is specified. + Example: apic=debug show_lapic=all + apm= [APM] Advanced Power Management See header of arch/x86/kernel/apm_32.c. @@ -491,6 +500,13 @@ and is between 256 and 4096 characters. It is defined in the file Also note the kernel might malfunction if you disable some critical bits. + cmo_free_hint= [PPC] Format: { yes | no } + Specify whether pages are marked as being inactive + when they are freed. This is used in CMO environments + to determine OS memory pressure for page stealing by + a hypervisor. + Default: yes + code_bytes [X86] How many bytes of object code to print in an oops report. Range: 0 - 8192 @@ -539,6 +555,10 @@ and is between 256 and 4096 characters. It is defined in the file console=brl,ttyS0 For now, only VisioBraille is supported. + consoleblank= [KNL] The console blank (screen saver) timeout in + seconds. Defaults to 10*60 = 10mins. A value of 0 + disables the blank timer. + coredump_filter= [KNL] Change the default value for /proc//coredump_filter. @@ -613,6 +633,12 @@ and is between 256 and 4096 characters. It is defined in the file See drivers/char/README.epca and Documentation/serial/digiepca.txt. + disable= [IPV6] + See Documentation/networking/ipv6.txt. + + disable_ipv6= [IPV6] + See Documentation/networking/ipv6.txt. + disable_mtrr_cleanup [X86] The kernel tries to adjust MTRR layout from continuous to discrete, to make X server driver able to add WB @@ -666,7 +692,8 @@ and is between 256 and 4096 characters. It is defined in the file earlyprintk= [X86,SH,BLACKFIN] earlyprintk=vga earlyprintk=serial[,ttySn[,baudrate]] - earlyprintk=dbgp + earlyprintk=ttySn[,baudrate] + earlyprintk=dbgp[debugController#] Append ",keep" to not disable it when the real console takes over. @@ -773,6 +800,13 @@ and is between 256 and 4096 characters. It is defined in the file by the set_ftrace_notrace file in the debugfs tracing directory. + ftrace_graph_filter=[function-list] + [FTRACE] Limit the top level callers functions traced + by the function graph tracer at boot up. + function-list is a comma separated list of functions + that can be changed at run time by the + set_graph_function file in the debugfs tracing directory. + gamecon.map[2|3]= [HW,JOY] Multisystem joystick and NES/SNES/PSX pad support via parallel port (up to 5 devices per port) @@ -785,6 +819,12 @@ and is between 256 and 4096 characters. It is defined in the file Format: off | on default: on + gcov_persist= [GCOV] When non-zero (default), profiling data for + kernel modules is saved and remains accessible via + debugfs, even when the module is unloaded/reloaded. + When zero, profiling data is discarded and associated + debugfs files are removed at module unload time. + gdth= [HW,SCSI] See header of drivers/scsi/gdth.c. @@ -922,7 +962,7 @@ and is between 256 and 4096 characters. It is defined in the file 1 -- enable informational integrity auditing messages. ima_hash= [IMA] - Formt: { "sha1" | "md5" } + Format: { "sha1" | "md5" } default: "sha1" ima_tcb [IMA] @@ -988,6 +1028,7 @@ and is between 256 and 4096 characters. It is defined in the file nomerge forcesac soft + pt [x86, IA64] io7= [HW] IO7 for Marvel based alpha systems See comment before marvel_specify_io7 in @@ -1004,7 +1045,7 @@ and is between 256 and 4096 characters. It is defined in the file No delay ip= [IP_PNP] - See Documentation/filesystems/nfsroot.txt. + See Documentation/filesystems/nfs/nfsroot.txt. ip2= [HW] Set IO/IRQ pairs for up to 4 IntelliPort boards See comment before ip2_setup() in @@ -1073,7 +1114,7 @@ and is between 256 and 4096 characters. It is defined in the file kgdboc= [HW] kgdb over consoles. Requires a tty driver that supports console polling. - (only serial suported for now) + (only serial supported for now) Format: [,baud] kmac= [MIPS] korina ethernet MAC address. @@ -1087,6 +1128,44 @@ and is between 256 and 4096 characters. It is defined in the file kstack=N [X86] Print N words from the kernel stack in oops dumps. + kvm.ignore_msrs=[KVM] Ignore guest accesses to unhandled MSRs. + Default is 0 (don't ignore, but inject #GP) + + kvm.oos_shadow= [KVM] Disable out-of-sync shadow paging. + Default is 1 (enabled) + + kvm-amd.nested= [KVM,AMD] Allow nested virtualization in KVM/SVM. + Default is 0 (off) + + kvm-amd.npt= [KVM,AMD] Disable nested paging (virtualized MMU) + for all guests. + Default is 1 (enabled) if in 64bit or 32bit-PAE mode + + kvm-intel.bypass_guest_pf= + [KVM,Intel] Disables bypassing of guest page faults + on Intel chips. Default is 1 (enabled) + + kvm-intel.ept= [KVM,Intel] Disable extended page tables + (virtualized MMU) support on capable Intel chips. + Default is 1 (enabled) + + kvm-intel.emulate_invalid_guest_state= + [KVM,Intel] Enable emulation of invalid guest states + Default is 0 (disabled) + + kvm-intel.flexpriority= + [KVM,Intel] Disable FlexPriority feature (TPR shadow). + Default is 1 (enabled) + + kvm-intel.unrestricted_guest= + [KVM,Intel] Disable unrestricted guest feature + (virtualized real and unpaged mode) on capable + Intel chips. Default is 1 (enabled) + + kvm-intel.vpid= [KVM,Intel] Disable Virtual Processor Identification + feature (tagged TLBs) on capable Intel chips. + Default is 1 (enabled) + l2cr= [PPC] l3cr= [PPC] @@ -1104,6 +1183,10 @@ and is between 256 and 4096 characters. It is defined in the file libata.dma=4 Compact Flash DMA only Combinations also work, so libata.dma=3 enables DMA for disks and CDROMs, but not CFs. + + libata.ignore_hpa= [LIBATA] Ignore HPA limit + libata.ignore_hpa=0 keep BIOS limits (default) + libata.ignore_hpa=1 ignore limits, using full disk libata.noacpi [LIBATA] Disables use of ACPI in libata suspend/resume when set. @@ -1111,7 +1194,7 @@ and is between 256 and 4096 characters. It is defined in the file libata.force= [LIBATA] Force configurations. The format is comma separated list of "[ID:]VAL" where ID is - PORT[:DEVICE]. PORT and DEVICE are decimal numbers + PORT[.DEVICE]. PORT and DEVICE are decimal numbers matching port, link or device. Basically, it matches the ATA ID string printed on console by libata. If the whole ID part is omitted, the last PORT and DEVICE @@ -1232,6 +1315,10 @@ and is between 256 and 4096 characters. It is defined in the file (machvec) in a generic kernel. Example: machvec=hpzx1_swiotlb + machtype= [Loongson] Share the same kernel image file between different + yeeloong laptop. + Example: machtype=lemote-yeeloong-2f-7inch + max_addr=nn[KMG] [KNL,BOOT,ia64] All physical memory greater than or equal to this physical address is ignored. @@ -1351,6 +1438,27 @@ and is between 256 and 4096 characters. It is defined in the file min_addr=nn[KMG] [KNL,BOOT,ia64] All physical memory below this physical address is ignored. + mini2440= [ARM,HW,KNL] + Format:[0..2][b][c][t] + Default: "0tb" + MINI2440 configuration specification: + 0 - The attached screen is the 3.5" TFT + 1 - The attached screen is the 7" TFT + 2 - The VGA Shield is attached (1024x768) + Leaving out the screen size parameter will not load + the TFT driver, and the framebuffer will be left + unconfigured. + b - Enable backlight. The TFT backlight pin will be + linked to the kernel VESA blanking code and a GPIO + LED. This parameter is not necessary when using the + VGA shield. + c - Enable the s3c camera interface. + t - Reserved for enabling touchscreen support. The + touchscreen support is not enabled in the mainstream + kernel as of 2.6.30, a preliminary port can be found + in the "bleeding edge" mini2440 support kernel at + http://repo.or.cz/w/linux-2.6/mini2440.git + mminit_loglevel= [KNL] When CONFIG_DEBUG_MEMORY_INIT is set, this parameter allows control of the logging verbosity for @@ -1392,6 +1500,16 @@ and is between 256 and 4096 characters. It is defined in the file mtdparts= [MTD] See drivers/mtd/cmdlinepart.c. + onenand.bdry= [HW,MTD] Flex-OneNAND Boundary Configuration + + Format: [die0_boundary][,die0_lock][,die1_boundary][,die1_lock] + + boundary - index of last SLC block on Flex-OneNAND. + The remaining blocks are configured as MLC blocks. + lock - Configure if Flex-OneNAND boundary should be locked. + Once locked, the boundary cannot be changed. + 1 indicates lock status, 0 indicates unlock status. + mtdset= [ARM] ARM/S3C2412 JIVE boot control @@ -1402,7 +1520,7 @@ and is between 256 and 4096 characters. It is defined in the file ('y', default) or cooked coordinates ('n') mtrr_chunk_size=nn[KMG] [X86] - used for mtrr cleanup. It is largest continous chunk + used for mtrr cleanup. It is largest continuous chunk that could hold holes aka. UC entries. mtrr_gran_size=nn[KMG] [X86] @@ -1448,15 +1566,23 @@ and is between 256 and 4096 characters. It is defined in the file going to be removed in 2.6.29. nfsaddrs= [NFS] - See Documentation/filesystems/nfsroot.txt. + See Documentation/filesystems/nfs/nfsroot.txt. nfsroot= [NFS] nfs root filesystem for disk-less boxes. - See Documentation/filesystems/nfsroot.txt. + See Documentation/filesystems/nfs/nfsroot.txt. nfs.callback_tcpport= [NFS] set the TCP port on which the NFSv4 callback channel should listen. + nfs.cache_getent= + [NFS] sets the pathname to the program which is used + to update the NFS client cache entries. + + nfs.cache_getent_timeout= + [NFS] sets the timeout after which an attempt to + update a cache entry is deemed to have failed. + nfs.idmap_cache_timeout= [NFS] set the maximum lifetime for idmapper cache entries. @@ -1468,7 +1594,7 @@ and is between 256 and 4096 characters. It is defined in the file of returning the full 64-bit number. The default is to return 64-bit inode numbers. - nmi_debug= [KNL,AVR32] Specify one or more actions to take + nmi_debug= [KNL,AVR32,SH] Specify one or more actions to take when a NMI is triggered. Format: [state][,regs][,debounce][,die] @@ -1489,6 +1615,11 @@ and is between 256 and 4096 characters. It is defined in the file symbolic names: lapic and ioapic Example: nmi_watchdog=2 or nmi_watchdog=panic,lapic + netpoll.carrier_timeout= + [NET] Specifies amount of time (in seconds) that + netpoll should wait for a carrier. By default netpoll + waits 4 seconds. + no387 [BUGS=X86-32] Tells the kernel to use the 387 maths emulation library even if a 387 maths coprocessor is present. @@ -1608,6 +1739,9 @@ and is between 256 and 4096 characters. It is defined in the file nomfgpt [X86-32] Disable Multi-Function General Purpose Timer usage (for AMD Geode machines). + nopat [X86] Disable PAT (page attribute table extension of + pagetables) support. + norandmaps Don't use address space randomization. Equivalent to echo 0 > /proc/sys/kernel/randomize_va_space @@ -1651,6 +1785,12 @@ and is between 256 and 4096 characters. It is defined in the file purges which is reported from either PAL_VM_SUMMARY or SAL PALO. + nr_cpus= [SMP] Maximum number of processors that an SMP kernel + could support. nr_cpus=n : n >= 1 limits the kernel to + supporting 'n' processors. Later in runtime you can not + use hotplug cpu feature to put more cpu back to online. + just like you compile the kernel NR_CPUS=n + nr_uarts= [SERIAL] maximum number of UARTs to be registered. numa_zonelist_order= [KNL, BOOT] Select zonelist order for NUMA. @@ -1669,6 +1809,11 @@ and is between 256 and 4096 characters. It is defined in the file waiting for the ACK, so if this is set too high interrupts *may* be lost! + omap_mux= [OMAP] Override bootloader pin multiplexing. + Format: ... + For example, to override I2C bus2: + omap_mux=i2c2_scl.i2c2_scl=0x100,i2c2_sda.i2c2_sda=0x100 + opl3= [HW,OSS] Format: @@ -1678,8 +1823,8 @@ and is between 256 and 4096 characters. It is defined in the file oprofile.cpu_type= Force an oprofile cpu type This might be useful if you have an older oprofile userland or if you want common events. - Format: { archperfmon } - archperfmon: [X86] Force use of architectural + Format: { arch_perfmon } + arch_perfmon: [X86] Force use of architectural perfmon on Intel CPUs instead of the CPU specific event set. @@ -1758,6 +1903,9 @@ and is between 256 and 4096 characters. It is defined in the file root domains (aka PCI segments, in ACPI-speak). nommconf [X86] Disable use of MMCONFIG for PCI Configuration + check_enable_amd_mmconf [X86] check for and enable + properly configured MMIO access to PCI + config space on AMD family 10h CPU nomsi [MSI] If the PCI_MSI kernel config parameter is enabled, this kernel boot option can be used to disable the use of MSI interrupts system-wide. @@ -1810,8 +1958,12 @@ and is between 256 and 4096 characters. It is defined in the file IRQ routing is enabled. noacpi [X86] Do not use ACPI for IRQ routing or for PCI scanning. - use_crs [X86] Use _CRS for PCI resource - allocation. + use_crs [X86] Use PCI host bridge window information + from ACPI. On BIOSes from 2008 or later, this + is enabled by default. If you need to use this, + please report a bug. + nocrs [X86] Ignore PCI host bridge windows from ACPI. + If you need to use this, please report a bug. routeirq Do IRQ routing for all PCI devices. This is normally done in pci_enable_device(), so this option is a temporary workaround @@ -1847,6 +1999,12 @@ and is between 256 and 4096 characters. It is defined in the file PAGE_SIZE is used as alignment. PCI-PCI bridge can be specified, if resource windows need to be expanded. + ecrc= Enable/disable PCIe ECRC (transaction layer + end-to-end CRC checking). + bios: Use BIOS/firmware settings. This is the + the default. + off: Turn ECRC off + on: Turn ECRC on. pcie_aspm= [PCIE] Forcibly enable or disable PCIe Active State Power Management. @@ -1854,6 +2012,14 @@ and is between 256 and 4096 characters. It is defined in the file force Enable ASPM even on devices that claim not to support it. WARNING: Forcing ASPM on may cause system lockups. + pcie_pme= [PCIE,PM] Native PCIe PME signaling options: + off Do not use native PCIe PME signaling. + force Use native PCIe PME signaling even if the BIOS refuses + to allow the kernel to control the relevant PCIe config + registers. + nomsi Do not use MSI for native PCIe PME signaling (this makes + all PCIe root ports use INTx for everything). + pcmv= [HW,PCMCIA] BadgePAD 4 pd. [PARIDE] @@ -1864,6 +2030,13 @@ and is between 256 and 4096 characters. It is defined in the file Format: { 0 | 1 } See arch/parisc/kernel/pdc_chassis.c + percpu_alloc= Select which percpu first chunk allocator to use. + Currently supported values are "embed" and "page". + Archs may support subset or none of the selections. + See comments in mm/percpu.c for details on each + allocator. This parameter is primarily for debugging + and performance comparison. + pf. [PARIDE] See Documentation/blockdev/paride.txt. @@ -1913,8 +2086,15 @@ and is between 256 and 4096 characters. It is defined in the file print-fatal-signals= [KNL] debug: print fatal signals - print-fatal-signals=1: print segfault info to - the kernel console. + + If enabled, warn about various signal handling + related application anomalies: too many signals, + too many POSIX.1 timers, fatal signals causing a + coredump - etc. + + If you hit the warning due to signal overflow, + you might want to try "ulimit -i unlimited". + default: off. printk.time= Show timing data prefixed to each printk message line @@ -2045,15 +2225,6 @@ and is between 256 and 4096 characters. It is defined in the file Useful for devices that are detected asynchronously (e.g. USB and MMC devices). - root_plug.vendor_id= - [ROOTPLUG] Override the default vendor ID - - root_plug.product_id= - [ROOTPLUG] Override the default product ID - - root_plug.debug= - [ROOTPLUG] Enable debugging output - rw [KNL] Mount root device read-write on boot S [KNL] Run init in single mode @@ -2063,6 +2234,8 @@ and is between 256 and 4096 characters. It is defined in the file sbni= [NET] Granch SBNI12 leased line adapter + sched_debug [KNL] Enables verbose scheduler debug messages. + sc1200wdt= [HW,WDT] SC1200 WDT (watchdog) driver Format: [,[,]] @@ -2334,6 +2507,18 @@ and is between 256 and 4096 characters. It is defined in the file stifb= [HW] Format: bpp:[:[:...]] + sunrpc.min_resvport= + sunrpc.max_resvport= + [NFS,SUNRPC] + SunRPC servers often require that client requests + originate from a privileged port (i.e. a port in the + range 0 < portnr < 1024). + An administrator who wishes to reserve some of these + ports for other uses may adjust the range that the + kernel's sunrpc client considers to be privileged + using these two parameters to set the minimum and + maximum port values. + sunrpc.pool_mode= [NFS] Control how the NFS server code allocates CPUs to @@ -2350,6 +2535,15 @@ and is between 256 and 4096 characters. It is defined in the file pernode one pool for each NUMA node (equivalent to global on non-NUMA machines) + sunrpc.tcp_slot_table_entries= + sunrpc.udp_slot_table_entries= + [NFS,SUNRPC] + Sets the upper limit on the number of simultaneous + RPC calls that can be sent from the client to a + server. Increasing these values may allow you to + improve throughput, but will also increase the + amount of memory reserved for use by the client. + swiotlb= [IA-64] Number of I/O TLB slabs switches= [HW,M68k] @@ -2416,7 +2610,13 @@ and is between 256 and 4096 characters. It is defined in the file tp720= [HW,PS2] - trace_buf_size=nn[KMG] [ftrace] will set tracing buffer size. + trace_buf_size=nn[KMG] + [FTRACE] will set tracing buffer size. + + trace_event=[event-list] + [FTRACE] Set and start specified trace events in order + to facilitate early boot debugging. + See also Documentation/trace/events.txt trix= [HW,OSS] MediaTrix AudioTrix Pro Format: @@ -2444,6 +2644,9 @@ and is between 256 and 4096 characters. It is defined in the file uart6850= [HW,OSS] Format: , + uhash_entries= [KNL,NET] + Set number of hash buckets for UDP/UDP-Lite connections + uhci-hcd.ignore_oc= [USB] Ignore overcurrent events (default N). Some badly-designed motherboards generate lots of @@ -2499,6 +2702,8 @@ and is between 256 and 4096 characters. It is defined in the file to a common usb-storage quirk flag as follows: a = SANE_SENSE (collect more than 18 bytes of sense data); + b = BAD_SENSE (don't collect more than 18 + bytes of sense data); c = FIX_CAPACITY (decrease the reported device capacity by one sector); h = CAPACITY_HEURISTICS (decrease the @@ -2520,6 +2725,13 @@ and is between 256 and 4096 characters. It is defined in the file medium is write-protected). Example: quirks=0419:aaf5:rl,0421:0433:rc + userpte= + [X86] Flags controlling user PTE allocations. + + nohigh = do not allocate PTE pages in + HIGHMEM regardless of setting + of CONFIG_HIGHPTE. + vdso= [X86,SH] vdso=2: enable compat VDSO (default with COMPAT_VDSO) vdso=1: enable VDSO (default) @@ -2558,6 +2770,11 @@ and is between 256 and 4096 characters. It is defined in the file vmpoff= [KNL,S390] Perform z/VM CP command after power off. Format: + vt.cur_default= [VT] Default cursor shape. + Format: 0xCCBBAA, where AA, BB, and CC are the same as + the parameters of the [?A;B;Cc escape sequence; + see VGA-softcursor.txt. Default: 2 = underline. + vt.default_blu= [VT] Format: ,,,..., Change the default blue palette of the console. @@ -2583,6 +2800,15 @@ and is between 256 and 4096 characters. It is defined in the file Default is 1, i.e. UTF-8 mode is enabled for all newly opened terminals. + vt.global_cursor_default= + [VT] + Format=<-1|0|1> + Set system-wide default for whether a cursor + is shown on new VTs. Default is -1, + i.e. cursors will be created by default unless + overridden by individual drivers. 0 will hide + cursors, 1 will display them. + waveartist= [HW,OSS] Format: ,,, @@ -2599,6 +2825,12 @@ and is between 256 and 4096 characters. It is defined in the file default x2apic cluster mode on platforms supporting x2apic. + x86_mrst_timer= [X86-32,APBT] + Choose timer option for x86 Moorestown MID platform. + Two valid options are apbt timer only and lapic timer + plus one apbt timer for broadcast timer. + x86_mrst_timer=apbt_only | lapic_and_apbt + xd= [HW,XT] Original XT pre-IDE (RLL encoded) disks. xd_geo= See header of drivers/block/xd.c.